Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLASTIC DEFORMATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1956

Plastic Deformation of Aluminum Single Crystals at Elevated Temperatures

This report describes the results of a comprehensive study of plastic deformation of aluminum single crystals over a wide range of temperatures. The results of constant-stress creep tests have been reported for the temperature range from 400 degrees to 900 degrees F. For these tests, a new capacitance-type extensometer was designed. This unit has a range of 0.30 inch over which the sensitivity is very nearly linear and can be varied from as low a sensitivity as is desired to a maximum of 20 microinches per millivolt with good stability. Experiments were carried out to investigate the effect of small amounts of prestraining, by two different methods, on the creep and tensile properties of these aluminum single crystals. From observations it has been concluded that plastic deformation takes place predominantly by slip which is accompanied by the mechanisms of kinking and polygonization.

Johnson, R D↗
NASA NTRS1984

Plastic deformation of silicon dendritic web ribbons during the growth

The distribution of slip dislocations in silicon dendritic web ribbons due to plastic deformation during the cooling phase of the growth was studied. The results show the existence of two distinguishable stress regions across the ribbon formed during the plastic deformation stage, namely, shear stress at the ribbon edges and tensile stress at the middle. In addition, slip dislocations caused by shear stress near the edges appear to originate at the twin plane.

Cheng, L. J.↗
NASA NTRS1982

Pressure concentrations due to plastic deformation of thin films or gaskets between anvils

Plastic deformation of either a sample or a gasket between diamond anvils leads to large pressure concentrations, i.e., the maximum pressure can be many times the average pressure. This behavior is discussed using elementary plasticity theory for the case where the pressures are sufficiently low that the yield stress can be assumed not to vary with pressure. It is then shown that the pressure concentration factor can be even much larger when the yield stress of the sample at the highest pressure is much greater than the yield stress at the lowest pressure. This is illustrated with solid xenon where it is shown that the assumption that Nelson and Ruoff made about the pressure distribution in their xenon samples is incorrect. The pressure distribution is shown to be much steeper than assumed. Thus, the pressure they observed electrical conduction in xenon was above 1 Mbar.

Chan, K. S.↗
NASA NTRS1939

Tensile elastic properties of 18:8 chromium-nickel steel as affected by plastic deformation

The relationship between stress and strain, and between stress and permanent set, for 18:8 alloy as affected by prior plastic deformation is discussed. Hysteresis and creep and their effects on the stress-strain and stress-set curves are also considered, as well as the influence of duration of the rest interval after cold work and the influence of plastic deformation on proof stresses, on the modulus of elasticity at zero stress, and on the curvature of the stress-strain line. A constant (c sub 1) is suggested to represent the variation of the modulus of elasticity with stress.

Mcadam, D J↗
DOE OSTI2025

Modification of Ni-20Cr corrosion dealloying behavior in molten fluorides via cold work induced plastic deformation

The corrosion dealloying behavior of cold-worked (CW) Ni20Cr alloy (wt%) was studied in molten LiF-NaF-KF (or FLiNaK) salts at 600 °C, equal to a homologous temperature (TH) of 0.52. Alloys were cold-rolled to achieve reductions of thickness of 10%, 30%, and 50% introducing plastic deformation and a high density of dislocations. Potentiostatic holds (Eapplied) were applied in two different electrode potential regimes. At 1.75VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, Cr dealloying to Cr(II) and Cr(III) is predominant, while at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, both Ni and Cr are oxidized in molten FLiNaK at 600 °C. In these potential regimes, dealloyed Ni20Cr displayed bicontinuous porosity within the grain interior and at grain boundaries, driven by the high driving force for Cr dissolution and sustained by defect mediated outward solid state diffusion of Cr in parallel with surface diffusion of Ni. The bicontinuous porous structure developed was observed to undergo further coarsening and densification of the Ni-rich ligaments at a higher electrode potential. The main effect of CW observed is the introduction of plastic deformation and dislocation substructures that serve as short-circuit paths for Cr solid state diffusion to surfaces exposed to FLiNaK. This modified the evolution of the bicontinuous porous structure which increased with CW substantially. Kinetic analysis reveals that the Cr dealloying at +1.75 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ and 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$ is initially charge transfer controlled, except for the 50% CW condition at 1.90 VK+/K$${\text{V}}_{{\text{K}}^{+}/{\text{K}}}$$, where the process becomes limited by slow Cr defect mediated bulk diffusion. The rate determining factors are explored and compared to experimental results.

Chan, Ho Lun↗
NASA NTRS1982

Plastic deformation and wear process at a surface during unlubricated sliding

The plastic deformation and wear of a 304 stainless steel surface sliding against an aluminum oxide rider with a spherical surface (the radius of curvature: 1.3 cm) were observed by using scanning electron and optical microscopes. Experiments were conducted in a vacuum of one million Pa and in an environment of fifty thousandth Pa of chlorine gas at 25 C. The load was 500 grams and the sliding velocity was 0.5 centimeter per second. The deformed surface layer which accumulates and develops successively is left behind the rider, and step shaped proturbances are developed even after single pass sliding under both environmental conditions. A fully developed surface layer is gradually torn off leaving a characteristic pattern. The mechanism for tearing away of the surface layer from the contact area and sliding track contour is explained assuming the simplified process of material removal based on the adhesion theory for the wear of materials.

Yamamoto, T.↗
NASA NTRS1983

Plastic deformation and wear process at a surface during unlubricated sliding

The plastic deformation and wear of a 304 stainless steel surface sliding against an aluminum oxide rider with a spherical surface (the radius of curvature: 1.3 cm) were observed by using scanning electron and optical microscopes. Experiments were conducted in a vacuum of one million Pa and in an environment of fifty thousandth Pa of chlorine gas at 25 C. The load was 500 grams and the sliding velocity was 0.5 centimeter per second. The deformed surface layer which accumulates and develops successively is left behind the rider, and step shaped proturbances are developed even after single pass sliding under both environmental conditions. A fully developed surface layer is gradually torn off leaving a characteristic pattern. The mechanism for tearing away of the surface layer from the contact area and sliding track contour is explained assuming the simplified process of material removal based on the adhesion theory for the wear of materials. Previously announced in STAR as N82-32735

Yamamoto, T.↗
NASA NTRS1982

Interaction of heat production, strain rate and stress power in a plastically deforming body under tensile test

At high strain rates the heat produced by plastic deformation can give rise to a rate dependent response even if the material has rate independent constitutive equations. This effect has to be evaluated when interpreting a material test, or else it could erroneously be ascribed to viscosity. A general thermodynamic theory of tensile testing of elastic-plastic materials is given in this paper; it is valid for large strain at finite strain rates. It enables discovery of the parameters governing the thermodynamic strain rate effect, provides a method for proper interpretation of the results of the tests of dynamic plasticity, and suggests a way of planning experiments in order to detect the real contribution of viscosity.

Paglietti, A.↗
NASA NTRS1986

Ultrasonic characterization of plastic deformation in metals

Acoustic tone burst spectroscopy is used to examine the effect of plastic deformation on higher order elastic properties of specimens of AISI 1016, 1045, 1095 and 8620 steel rods by measuring the stress acoustic constants (SACs). The SAC is found to be influenced by prestraining, and prestrain SAC measurements on 8620 steel demonstrate similar behavior to previously measured steels even though the composition of 8620 steel is significantly different. It is suggested from bias stress measurements that the stress acoustic response of prestrained 8620 steel is sensitive to the sign of the applied stress due to the different directions is which dislocations move under tension as opposed to compression, providing an approach to nondestructive testing of residual stress in steels.

Allison, S. G.↗
NASA NTRS1984

Finite elastic-plastic deformation of polycrystalline metals

Applying Hill's self-consistent method to finite elastic-plastic deformations, the overall moduli of polycrystalline solids are estimated. The model predicts a Bauschinger effect, hardening, and formation of vertex or corner on the yield surface for both microscopically non-hardening and hardening crystals. The changes in the instantaneous moduli with deformation are examined, and their asymptotic behavior, especially in relation to possible localization of deformations, is discussed. An interesting conclusion is that small second-order quantities, such as shape changes of grains and residual stresses (measured relative to the crystal elastic moduli), have a first-order effect on the overall response, as they lead to a loss of the overall stability by localized deformation. The predicted incipience of localization for a uniaxial deformation in two dimensions depends on the initial yield strain, but the orientation of localization is slightly less than 45 deg with respect to the tensile direction, although the numerical instability makes it very difficult to estimate this direction accurately.

Iwakuma, T.↗