Plastic deformation waves and heat generated near the yield point of annealed aluminum.
Plastic deformation wave propagation and heat generated near yield point of annealed aluminum
Dillon, O. W., Jr.↗
SEARCH · Search NASA
Results for “PLASTIC YIELDING”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Limitations to the small scale yielding approximation for crack tip plasticity
Recent finite-element results by S. G. Larsson and A. J. Carlsson suggest a limited range of validity to the 'small scale yielding approximation,' whereby small crack tip plastic zones are correlated in terms of the elastic stress intensity factor. It is shown with the help of a model for plane strain yielding that their results may be explained by considering the non-singular stress, acting parallel to the crack at its tip, which accompanies the inverse square-root elastic singularity. Further implications of the non-singular stress term for crack tip deformations and fracturing are examined. It is suggested that its effect on crack tip parameters, such as the opening displacement and J-integral, is less pronounced than its effect on the yield zone size.
Rice, J. R.↗
Dispersion of borax in plastic is excellent fire-retardant heat insulator
A mix of borax powder and a chlorinated anhydrous polyester resin yields a plastic composition that is fire-retardant, yields a minimum of toxic gases when heated, and exhibits high thermal insulating properties. This composition can be used as a coating or can be converted into laminated or cast shapes.
Evans, H.↗
Wave speeds and slowness surface in elastic-plastic media obeying Tresca's yield condition
With the coordinate axes chosen along the principal axes of the stress, the plastic wave speeds c(f) and c(s) depend on the direction of propagation, not on the stress components. The directions along which c(f) and c(s) assume the largest and smallest values are determined. A means of determining the slowness surface when the coordinate axes are not along the principal axes of stress is presented.
Ting, T. C. T.↗
Yielding Torque-Tube System Reduces Crash Injuries
Yielding torque-tube system minimizes injuries by limiting load transferred to occupant in crash. When properly integrated into seat structure, torque tube yields in plastic deformation stage of material and maintains a relatively constant resistance to applied torque for many degrees of rotation. Yielding torque-tube system is expected to find application in aircraft and automobile industries.
Mcsmith, D. G.↗
Pinning, flow and plastic deformation of flux vortices in high T(sub c) superconductors
In high temperature superconductor (HTSC) materials the vortices are highly mobile and flexible. This is reflected in different models of melt of a vortex lattice. Another aspect of the problem is stressed: an easy nucleation and high mobility of dislocations in the vortex lattice. Some models of plastic deformation of vortex lattice are considered as a result of its interaction with a real crystal structure. Depinning is interpreted as yield of plastic flow is vortex medium. Effect of macroscopic defects in crystal structures (pores, inclusions, grain and domain boundaries) is being considered in detail. Available experimental facts on magnetization and a critical current in HTSC and conventional superconductors are discussed from the points of view of depinning to vortices vs. plastic flow of vortices vs. plastic flow of vortices medium.
Roytburd, A.↗
Nonlinear quasi-fracture behavior of polymers
This paper deals with the nonlinear quasi-fracture behavior of polymers. Using the finite element method, the quasi-fracture model composed of an isolated craze opening with a nonlinear boundary envelope forces represented by oriented fibril domains is analyzed in simply-stressed rectangular plate. The stress distribution, the displacement profile, as well as the yield or plastic or flow zone adjacent to the craze tips are obtained. It is found that the variation of the stress distribution near the craze tip is not as sharp as that for an elastic crack. The initial load required for yielding or flowing is greater for the quasifracture as compared with that for a classical fracture. Under the same load the yield or flow zone is somewhat smaller as compared with that obtained on the basis of linear elastic-plastic fracture mechanics theory.
Sun, B. N.↗
Automated Grain Yield Behavior Classification
A method for classifying grain stress evolution behaviors using unsupervised learning techniques is presented. The method is applied to analyze grain stress histories measured in-situ using high-energy X-ray diffraction microscopy (HEDM) from the aluminum-lithium alloy Al-Li 2099 at the elastic-plastic transition (yield). The unsupervised learning process automatically classified the grain stress histories into four groups: major softening, no work-hardening or softening, moderate work-hardening, and major work-hardening. The orientation and spatial dependence of these four groups are discussed. In addition, the generality of the classification process to other samples is explored.
Pagan, Darren C↗
Plastic stability of spherical plates.
Plastic stability of externally loaded flat circular and spherical plates, examining axisymmetric and asymmetric buckling modes
COMPRESSION BUCKLING↗
Application of the methods of limit analysis to the evaluation of the strength of fiber-reinforced composites
Limit analysis of plasticity applied to strength evaluation of fiber reinforced composites
PLASTICITY↗
Continuity gage measurement of crack growth on flat and curved surfaces at cryogenic temperatures.
Continuity gauge measurement of crack growth on flat and curved surfaces at cryogenic temperatures
PLASTIC YIELDING↗
The role of energy in deformation
Necking, yield, and plastic flow in electrical analogs of mechanical systems with respect to energy conversion effects on mechanical behavior of various materials
Gruntfest, I. J.↗
An investigation into the role of plastic failure in crater modification
The mechanical stability of an impact crater is analyzed in this paper via a quasi-static, axisymmetric slip line theory of plasticity. The yield model incorporated is Mohr-Coulomb and a simplified rectangular profile is used for the transient cavity. The degree of stability (or instability) is described as a function of internal friction angle, depth/diameter ratio, and a dimensionless parameter. To match the observed slumping of large lunar craters the cohesion strength of the lunar surface material must be low (less than 20 bars) and the angle of internal friction must be less than 2 deg. It is not implausible that these failure strength characteristics are realized by freshly shocked rock.
Mckinnon, W. B.↗
Materials for a Stirling engine heater head
Work done on the 25-kW advanced Stirling conversion system (ASCS) terrestrial solar program in establishing criteria and selecting materials for the engine heater head and heater tubes is described. Various mechanisms contributing to incompatibility between materials are identified and discussed. Large thermal gradients, coupled with requirements for long life (60,000 h at temperature) and a large number of heatup and cooldown cycles (20,000) drive the design from a structural standpoint. The pressurized cylinder is checked for creep rupture, localized yielding, reverse plasticity, creep and fatigue damage, and creep ratcheting, in addition to the basic requirements for bust and proof pressure. In general, creep rupture and creep and fatigue interaction are the dominant factors in the design. A wide range of materials for the heater head and tubes was evaluated. Factors involved in the assessment were strength and effect on engine efficiency, reliability, and cost. A preliminary selection of Inconel 713LC for the heater head is based on acceptable structural properties but driven mainly by low cost. The criteria for failure, the structural analysis, and the material characteristics with basis for selection are discussed.
Noble, J. E.↗
Use of photostress and strain gages to analyze behavior of weldments
Tensile and pure bending tests were conducted on specimens having welded joints made from 2219-T87 aluminum alloy and 2319 filler. Data were collected using photoelastic coatings and strain gages. Stress-strain relationships and contraction ratios were determined at several points in a grid covering the weld material and heat affected zone. Material behavior was nonlinear and nonuniform at all points in the grid and contraction ratios did not conform to those predicted by Chakrabarty's plasticity theory. Yielding in joints made using four new welding procedures was examined. None of the new procedures produced more uniform yielding in the joint.
Gambrell, S. C., Jr.↗
Microscope Cells Containing Multiple Micromachined Wells
Tech Briefs, May 2003 19 Manufacturing Microscope Cells Containing Multiple Micromachined Wells The cost per cell has been reduced substantially. John H. Glenn Research Center, Cleveland, Ohio An improved design for multiple-well microscope cells and an associated improved method of fabricating them have been devised. [As used here, "well" denotes a cavity that has a volume of about 1 or 2 L and that is used to hold a sample for examination under a microscope. As used here, "cell" denotes a laminate, based on a standard 1- by 3-in. (2.54- by 7.62-cm) microscope slide, that comprises (1) the slide as the lower layer, (2) an intermediate layer that contains holes that serve as the wells, and (3) a top layer that either consists of, or is similar to, a standard microscope-slide cover slip.] The improved design and method of fabrication make it possible to increase (relative to a prior design and method of fabrication) the number of wells per cell while reducing the fabrication loss and reducing the cost per cell to about one-tenth of the prior value. In the prior design and method, the slide, well, and cover-slip layers were made from silicate glass. The fabrication of each cell was a labor-intensive process that included precise cutting and grinding of the glass components, fusing of the glass components, and then more grinding and polishing to obtain desired dimensions. Cells of the prior design were expensive and fragile, the rate of loss in fabrication was high, and the nature of the glass made it difficult to increase the number of cells per well. Efforts to execute alternative prior designs in plastic have not yielded satisfactory results because, for typical applications, plastics are not sufficiently thermally or chemically stable, not sufficiently optically clear, and/or not hard enough to resist scratching. The figure depicts a cell of the present improved type. The slide and cover-slip layers are made of a low-thermal-expansion glass (Pyrex(TradeMark) or equivalent) and the intermediate (well layer) is made of SiO2 - a combination of materials that results in a laminate stronger than one made from layers of silicate glass. Before the layers are assembled into the laminate, the SiO2 layer is micromachined to form the wells plus shallow grooves that, when subsequently covered with the cover slip, become capillary channels that are used to fill the wells with samples. The micromachining is accomplished by use of the same patterning and etching techniques used to fabricate microelectromechanical systems (MEMS).
Turner, Walter↗
Closure of fatigue cracks at high strains
Experiments were conducted on smooth specimens to study the closure behavior of short cracks at high cyclic strains under completely reversed cycling. Testing procedures and methodology, and closure measurement techniques, are described in detail. The strain levels chosen for the study cover from predominantly elastic to grossly plastic strains. Crack closure measurements are made at different crack lengths. The study reveals that, at high strains, cracks close only as the lowest stress level in the cycle is approached. The crack opening is observed to occur in the compressive part of the loading cycle. The applied stress needed to open a short crack under high strain is found to be less than for cracks under small scale yielding. For increased plastic deformations, the value of sigma sub op/sigma sub max is observed to decrease and approaches the value of R. Comparison of the experimental results with existing analysis is made and indicates the limitations of the small scale yielding approach where gross plastic deformation behavior occurs.
Iyyer, N. S.↗
Improving the low temperature ductility of NiAl
As part of a study aimed at developing a ductile NiAl-based alloy, ingots of Ni-Fe-Al alloys were cast and hot extruded to rods. The purpose of the iron additions was two-fold viz; to produce a change in the slip vector from 001 to 111 line and, in one alloy, to add a L1(2)-structured ductile second phase. Extruded Ni-20Al-30Fe was two-phase, containing a pro-eutectic B2 phase in a fine lamellar structure of B2+L1(2) phases. Room temperature tensile testing of both single extruded and double extruded alloys resulted in 8-percent and 22-percent plastic elongation and yield stresses of 850 and 760 MPa, respectively. Fracture in both cases occurred by ductile tearing of the eutectic and transgranular cleavage of the proeutectic phase at 1350 MPa. The ductility in double extruded condition is higher than that reported earlier in rapidly solidified wires by Inoue et al. (1984). By comparison, extruded single-phase B2-structured Ni-30Al-20Fe exhibited a fracture strength of 780 MPa, no plasticity, and a mixture of intergranular fracture and transgranular cleavage. This is contrast to earlier work by Inoue et al. where a yield stress of 400 MPa, 5 percent plastic strain, and a mixture of dimple and intergranular fracture was reported.
Guha, Sumit↗