Search NASA⌕ Search

SEARCH · Search NASA

Results for “PNEUMATIC EQUIPMENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Mechanical-load indicator

By rotation of washerlike part, mechanical indicator shows when predetermined compression or tension load has been reached. Indicator consists of bolt, sleeve, load-indicating washer, and nut. Besides application as load indicator, device has uses as remote indicator of mechanical action. Rotating washer can also act as sequencer, signaling action to begin upon attainment of certain load. It can be used, for example, to initiate work cycle after stored energy has been built up in hydraulic or pneumatic power equipment. It can also be used as remote, nonelectrical switch in hazardous environments.

Appleberry, W. T.↗
NASA NTRS1982

Planar equations of rollout motion for an aircraft with free or steerable landing gears

Equations were derived for an aircraft in a three-point attitude. Transient tire forces were simulated by delaying the application of forces derived from steady-state considerations. Predicted rollout trajectories were similar to those measured in tests of a small-scale landing-gear model equipped with pneumatic tires (where a laterally sloping runway was used to simulate a crosswind), both with and without nose-wheel steering.

Sleeper, R. K.↗
NASA NTRS1949

Transient Behavior of Lumped-Constant Systems for Sensing Gas Pressures

The development of theoretical equations describing the behavior of a lumped-constant pressure-sensing system under transient operation Is presented with experimental data that show agreement with the equations. A pressure-sensing system 'consisting of a tube terminating in a reservoir is investigated for the transient relation between a presSure disturbance at the open end of the tube and the pressure response in the reservoir. Design parameters are presented that can be adjusted to achieve a desired performance fran such a system when the system is considered as a transfer member of a control loop.

INSTRUMENTS - PRESSURE↗
NASA NTRS1988

Aerodynamics in ground effect and predicted landing ground roll of a fighter configuration with a secondary-nozzle thrust reverser

An experimental investigation of the in-ground effect aerodynamic characteristics and predicted landing-ground-roll performance of wing-canard fighter configuration with a secondary nozzle thrust reverser was completed. These tests were conducted in the Langley 14 by 22 foot Subsonic Wind Tunnel using a model equipped with a pneumatic jet for thrust simulation of nozzle pressure ratios up to 4.0. The model was tested in the landing rollout configuration at approx. wheel touchdown height for a range of decreasing dynamic pressure from 50 psf down to 10 psf. Landing-ground-roll predictions of the configuration were calculated using the wind tunnel results.

Banks, Daniel W.↗
NASA NTRS2003

Effect of Intercycle Ice Accretions on Airfoil Performance

This paper presents the results of an experimental study designed to characterize and evaluate the aerodynamic performance penalties of residual and intercycle ice accretions that result from the cyclic operation of a typical aircraft deicing system. Icing wind tunnel tests were carried out on a 36-inch chord NACA 23012 airfoil section equipped with a pneumatic deicer for several different FAR 25 Appendix C cloud conditions. Results from the icing tests showed that the intercycle ice accretions were much more severe in terms of size and shape than the residual ice accretions. Molds of selected intercycle ice shapes were made and converted to castings that were attached to the leading edge of a 36-inch chord NACA 23012 airfoil model for aerodynamic testing. The aerodynamic testing revealed that the intercycle ice shapes caused a significant performance degradation. Maximum lift coefficients were typically reduced about 60% from 1.8 (clean) to 0.7 (iced) and stall angles were reduced from 17 deg. (clean) to 9 deg. (iced). Changes in the Reynolds number (from 2.0 x 10(exp 6) to 10.5 x 10(exp 6) and Mach number (from 0.10 to 0.28) did not significantly affect the iced-airfoil performance.

Broeren, Andy P.↗