Search NASA⌕ Search

SEARCH · Search NASA

Results for “PNEUMATICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Experimental Development and Evaluation of Pneumatic Powered-Lift Super-STOL Aircraft

The powered-lift Channel Wing concept has been combined with pneumatic Circulation Control aerodynamic and propulsive technology to generate a Pneumatic Channel Wing (PCW) configuration intended to have Super-STOL or VSTOL capability while eliminating many of the operational problem areas of the original Channel Wing vehicle. Wind-tunnel development and evaluations of a PCW powered model conducted at Georgia Tech Research Institute (GTRI) have shown substantial lift capabilities for the blown configuration (CL values of 10 to 11). Variation in blowing of the channel was shown to be more efficient than variation in propeller thrust in terms of lift generation. Also revealed was the ability to operate unstalled at very high angles of attack of 40 deg - 45 deg, or to achieve very high lift at much lower angle of attack to increase visibility and controllability. In order to provide greater flexibility in Super-STOL takeoffs and landings, the blown model also displayed the ability to interchange thrust and drag by varying blowing without any moving parts. A preliminary design study of this pneumatic vehicle based on the two technologies integrated into a simple Pneumatic Channel Wing configuration showed very strong Super-STOL potential. This paper presents these experimental results, discusses variations in the configuration geometry under development, and addresses additional considerations to extend this integrated technology to advanced design studies of PCW-type vehicles.

Englar, Robert J.↗
NASA NTRS2013

Pneumatic Proboscis Heat-Flow Probe

Heat flow is a fundamental property of a planet, and provides significant constraints on the abundance of radiogenic isotopes, the thermal evolution and differentiation history, and the mechanical properties of the lithosphere. Heat-flow measurements are also essential in achieving at least four of the goals set out by the National Research Council for future lunar exploration. The heat-flow probe therefore directly addresses the goal of the Lunar Geophysical Network, which is to understand the interior structure and composition of the Moon. A key challenge for heat flow measurement is to install thermal sensors to the depths approximately equal to 3 m that are not influenced by the diurnal, annual, and longer-term fluctuations of the surface thermal environment. In addition, once deployed, the heat flow probe should cause little disturbance to the thermal regime of the surrounding regolith. A heat-flow probe system was developed that has two novel features: (1) it utilizes a pneumatic (gas) approach, excavates a hole by lofting the lunar soil out of the hole, and (2) deploys the heat flow probe, which utilizes a coiled up tape as a thermal probe to reach greater than 3-meter depth. The system is a game-changer for small lunar landers as it exhibits extremely low mass, volume, and simple deployment. The pneumatic system takes advantage of the helium gas used for pressurizing liquid propellant of the lander. Normally, helium is vented once the lander is on the surface, but it can be utilized for powering pneumatic systems. Should sufficient helium not be available, a simple gas delivery system may be taken specifically for the heat flow probe. Either way, the pneumatic heat flow probe system would be much lighter than other systems that entirely rely on the electrical power of the lander.

Zacny, Kris↗
NASA NTRS2017

Shape Memory Alloys (SMAs) for Non-Pneumatic Tires

Conventional mobility elements, such as pneumatic tires, suffer from a number of issues related to reliability. Two of the more prevalent problems are the high likelihood of single point failure owing to puncture (i.e. flat tire), and loss of efficiency due to reduction in tire pressure over time. In order to overcome these limitations, alternative compliant tire designs not requiring pneumatics have been developed. However, although current designs have significantly reduced the aforementioned issues, they tend to have their own set of limitations. First, non-pneumatic tires designed for high load applications often have restricted envelopment capability, making their performance less than optimal, especially on uneven terrain. Second, tires designed with larger envelopment capability tend to suffer from large amounts of plasticity (permanent deformation) or failure (rupture). Both of these limitations are the direct result of the choice of material being used for the design; conventional metals undergo plastic deformation at low strain while elastomer based designs are often too rigid for the localized deformations needed for high envelopment. Recent advancements at the NASA Glenn research center in a unique class of metals know as shape memory alloys (SMAs) has opened the design space for non-pneumatic compliant tire technologies allowing designs to incorporate orders of magnitude more deformation without damage. The work presented herein highlights the advantages of using SMAs as compared to conventional metals. Additionally, the development of a unique SMA compliant tire design capable of carrying up to 8.9 kN (2000 lbf) with reversible, local deformations on the order of the side wall height will be presented.

Padula, Santo↗
DOE OSTI2016

Microfluidic pressure amplifier circuits and electrostatic gates for pneumatic microsystems

An electrostatic actuator is provide that can include a fluidic line, a first electrode, and a second electrode such that a gate chamber portion of the fluidic line is sandwiched between the first electrode and the second electrode. The electrostatic actuator can also include a pressure-balancing channel in fluid communication with the gate chamber portion where the first electrode is sandwiched between the pressure-balancing channel and the gate chamber portion. A pneumatic valve system is provided which includes an electrostatic gate and a fluidic channel fluidly separate from a fluidic control line. A pneumatic valve portion of the fluidic control line can be positioned relative to a portion of the fluidic channel such that expansion of the pneumatic valve portion restricts fluid flow through the fluidic channel. Methods of using an electrostatic actuator and a pneumatic valve system are also provided.

42 ENGINEERING↗
DOE OSTI2017

Determination of the Most Likely Wear Zones of Pipe Bends in the Pulsed Pneumatic Conveyor at the RT-1 Plant

The results of an experimental investigation and numerical modeling of the most likely high-wear zones in 90° pipeline bends in the pulsed pneumatic conveyor system at the RT-1 plant of the Mayak Industrial Association are presented. The experimental studies were conducted on a model of a pulsed pneumatic conveyor system; the numerical modeling of the gas-dynamic flow in the pipeline channel was performed in a model of a two-dimensional non-stationary motion of a compressible medium. It was found on the basis of the experimental results obtained using the model and numerical modeling in the homogeneous approximation that local regions with high wear of walls in the 90° pipe bends in the pulsed pneumatic conveyor do indeed exist and their experimentally found positions agree with the calculations.

42 ENGINEERING↗
DOE OSTI2014

Controllable pneumatic generator based on the catalytic decomposition of hydrogen peroxide

This paper presents a novel compact and controllable pneumatic generator that uses hydrogen peroxide decomposition. A fuel micro-injector using a piston-pump mechanism is devised and tested to control the chemical decomposition rate. By controlling the injection rate, the feedback controller maintains the pressure of the gas reservoir at a desired pressure level. Thermodynamic analysis and experiments are performed to demonstrate the feasibility of the proposed pneumatic generator. Using a prototype of the pneumatic generator, it takes 6 s to reach 3.5 bars with a reservoir volume of 200 ml at the room temperature, which is sufficiently rapid and effective to maintain the repetitive lifting of a 1 kg mass.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Instrumentation and Data Analysis Supporting the Transient Rod Pneumatic System Design Study at the Annular Core Research Reactor

The Sandia National Laboratories Annular Core Research Reactor (ACRR) has been experiencing intermittent failures of its pneumatically operated transient rod system. The most frequent failures have been to the dashpot rod where it connects to the upper aluminum connecting rod. Within the three systems, Transient Rod (TR) A has the most frequent failures. In order to conduct the pulse operations, the Transient Rods are pneumatically driven to quickly remove "poison" from the reactor core. During these pulse operations increased forces and vibrations are placed on the TR system. In an effort to fix these problems, Sandia's TA-V Nuclear Reactor and Systems Engineering Department (Engineering Department) has started an extensive Transient Rod Pneumatic System Design Study. The goal of this study is to determine the causes of the elevated failure rates in TR A. This necessitates an increased understanding of the dynamics in the TR systems. This report will cover the approach taken and reasoning behind the choices of instrumentation, calibration, data collection and data analysis used to diagnose these failures. In order to determine the types and specifications for the sensors that will be installed, estimates of the TR system performance needed to be determined. Using known and assumed parameters, mechanical and thermodynamic models were developed, and calculations performed to estimate ranges of displacement, speed, and acceleration experienced by the transient rod system. After some preliminary data collection, the thermodynamic models were refined for better accuracy. After installation of the full suite of sensors, data can be collected and analyzed in order to determine the cause of the increased failures.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2015

Wireless Pneumatic Thermostat Evaluation, Ronald Reagan Building and International Trade Center

To be effective at maintaining indoor air conditions, a building heating, ventilation, and air conditioning (HVAC) system needs to be controlled in some fashion. The control system needs to sense the temperature of a space, feeding it to a control system, and manipulate the HVAC equipment to maintain desired temperatures for the occupants. Within the portfolio of buildings under the jurisdiction, custody, or control of the General Services Administration (GSA), approximately 20% have HVAC systems that are operated by pneumatic control systems. These buildings are under the same energy conservation mandates as all federal facilities. Unfortunately, the major drawback to pneumatic systems is that they are not capable of implementing automated energy-saving control strategies. They can’t automatically change the thermostat setting at night and on weekends in the same way as more modern control systems such as direct digital controls (DDCs). Converting a building from a pneumatic control system to DDCs is typically cost prohibitive.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1969

Pneumatic analog-to-pulse frequency converter

Pneumatic analog-to-pulse frequency converter circuit has output pulse frequency proportional to the pressure level of the input signal. Converter circuit drives a pneumatic stepping motor and is part of a pneumatic control system for nuclear powered spacecraft.

Dustin, M. O.↗
NASA NTRS1974

Vibration and recoil control of pneumatic hammers

Vibration sources are described for pneumatic hammers used in the mining industry (pick hammers), in boiler shops (riveting hammers), etc., bringing to light the fact that the principal vibration source is the variation in air pressure inside the cylinder. The present state of the art of vibration control of pneumatic hammers as it is practiced abroad, and the solutions adopted for this purpose, are discussed. A new type of pneumatic hammer with a low noise and vibration level is presented.

Constantinescu, I. N.↗
NASA NTRS1977

Evacuation of coal from hoppers/silos with low pressure pneumatic blasting systems

The need for an efficient, economical, effective and quiet device for moving coal and other difficult bulk solids was recognized. Thus came the advent of the low pressure pneumatic blasting system - a very efficient means of using a small amount of plant air (up to 125 PSI) to eliminate the most troublesome material hang-ups in storage containers. This simple device has one moving part and uses approximately 3% of the air consumed by a pneumatic vibrator on the same job. The principle of operation is very simple: air stored in the unit's reservoir is expelled directly into the material via a patented quick release valve. The number, size, and placement of the blaster units on the storage vessel is determined by a series of tests to ascertain flowability of the problem material. These tests in conjunction with the hopper or silo configuration determine specification of a low pressure pneumatic blasting system. This concept has often proven effective in solving flow problems when all other means have failed.

Fischer, J. S.↗
NASA NTRS1998

Continued Development and Application of Circulation Control Pneumatic Technology to Advanced Transport Aircraft

Personnel of the Georgia Tech Research Institute (GTRI) Aerospace and Transportation Lab have completed a four-year grant program to develop and evaluate the pneumatic aerodynamic technology known as Circulation Control (CC) or Circulation Control Wing (CCW) for advanced transport aircraft. This pneumatic technology, which employs low-level blowing from tangential slots over round or near-round trailing edges of airfoils, greatly augments the circulation around a lifting or control surface and thus enhances the aerodynamic forces and moments generated by that surface. Two-dimensional force augmentations as high as 80 times the input blowing momentum coefficient have been recorded experimentally for these blown devices, thus providing returns of 8000% on the jet momentum expended. A further benefit is the absence of moving parts such as mechanical flaps, slats, spoilers, ailerons, elevators and rudders from these pneumatic surfaces, or the use of only very small, simple, blown aerodynamic surfaces on synergistic designs which integrate the lift, drag and control surfaces. The application of these devices to advanced aircraft can offer significant benefits in their performance, efficiency, simplicity, reliability, economic cost of operation, noise reduction, and safety of flight. To further develop and evaluate this potential, this research effort was conducted by GTRI under grant for the NASA Langley Research Center, Applied Aerodynamics Division, Subsonic Aerodynamics Branch, between June 14, 1993 and May 31, 1997.

Englar, Robert J.↗
NASA NTRS2003

Compact, Pneumatically Actuated Filter Shuttle

A compact, pneumatically actuated filter shuttle has been invented to enable alternating imaging of a wind-tunnel model in two different spectral bands characteristic of the pressure and temperature responses of a pressure and temperature-sensitive paint. This filter shuttle could also be used in other settings in which there are requirements for alternating imaging in two spectral bands. Pneumatic actuation was chosen because of a need to exert control remotely (that is, from outside the wind tunnel) and because the power leads that would be needed for electrical actuation would pose an unacceptable hazard in the wind tunnel. The entire shuttle mechanism and its housing can be built relatively inexpensively [<$500 (prices as of year 2000)] from off-the-shelf parts. The shuttle mechanism (see Figure 1) is contained in a housing that has dimensions of 4 by 6 by 2 in. (about 10 by 15 by 5 cm). Two 2-in. (=5-cm)-diameter standard scientific-grade band-pass filters are mounted on sliding panels in a dual-track frame. The mechanism is positioned and oriented so the panels slide sideways with respect to the optical axis of a charge-coupled-device camera used for viewing the wind-tunnel model. The mechanism includes a pneumatic actuator connected to a linkage. The linkage converts the actuator stroke to a scissor-like motion that places one filter in front of the camera and the other filter out of the way. Optoelectronic sensors detect tabs on the sliding panels for verification of the proper positioning of the filters.

Leighy, Bradley D.↗
NASA NTRS2011

A Model-Based Prognostics Approach Applied to Pneumatic Valves

Within the area of systems health management, the task of prognostics centers on predicting when components will fail. Model-based prognostics exploits domain knowledge of the system, its components, and how they fail by casting the underlying physical phenomena in a physics-based model that is derived from first principles. Uncertainty cannot be avoided in prediction, therefore, algorithms are employed that help in managing these uncertainties. The particle filtering algorithm has become a popular choice for model-based prognostics due to its wide applicability, ease of implementation, and support for uncertainty management. We develop a general model-based prognostics methodology within a robust probabilistic framework using particle filters. As a case study, we consider a pneumatic valve from the Space Shuttle cryogenic refueling system. We develop a detailed physics-based model of the pneumatic valve, and perform comprehensive simulation experiments to illustrate our prognostics approach and evaluate its effectiveness and robustness. The approach is demonstrated using historical pneumatic valve data from the refueling system.

Daigle, Matthew J.↗
NASA NTRS2019

Utilizing Shape Memory Alloys for Novel, Non-Pneumatic Tire Design - Designing for the Best of Both Worlds

Materials are a fundamental building block that often get overlooked as a critical component that shapes our world. Numerous products that impact our lives are enabled by the materials from which they are made. With regard to Martian and lunar rover applications, conventional mobility elements, such as pneumatic tires, suffer from a number of issues related to reliability. Two of the more prevalent problems are the high likelihood of single point failure owing to puncture (i.e. flat tire), and loss of efficiency due to reduction in tire pressure over time. Solid, rigid wheels suffer from the inability to handle the high, localized loads while encountering rugged terrain and also produce relatively poor traction and operating efficiency. In an effort to overcome these problems, non-pneumatic, compliant tire designs are being developed, using Nickel-Titanium (NiTi), a thermally activated shape memory alloy (SMA), that is less sensitive to temperature and exhibits much greater plastic deformation than do conventional vulcanized rubber pneumatic tires.

Padula, Santo, II↗
NASA NTRS2019

Utilizing Shape Memory Alloys for Novel, Non-Pneumatic Tire Design - Designing for the Best of Both Worlds

Materials are a fundamental building block that often get overlooked as a critical component that shapes our world. Numerous products that impact our lives are enabled by the materials from which they are made. With regard to Martian and lunar rover applications, conventional mobility elements, such as pneumatic tires, suffer from a number of issues related to reliability. Two of the more prevalent problems are the high likelihood of single point failure owing to puncture (i.e. flat tire), and loss of efficiency due to reduction in tire pressure over time. Solid, rigid wheels suffer from the inability to handle the high, localized loads while encountering rugged terrain and also produce relatively poor traction and operating efficiency. In an effort to overcome these problems, non-pneumatic, compliant tire designs are being developed, using Nickel-Titanium (NiTi), a thermally activated shape memory alloy (SMA), that is less sensitive to temperature and exhibits much greater plastic deformation than do conventional vulcanized rubber pneumatic tires.

Padula, Santo, II↗
DOE OSTI2016

Buckling Pneumatic Linear Actuators Inspired by Muscle

To being, the mechanical features of biological muscles are difficult to reproduce completely in synthetic systems. A new class of soft pneumatic structures (vacuum-actuated muscle-inspired pneumatic structures) is described that combines actuation by negative pressure (vacuum), with cooperative buckling of beams fabricated in a slab of elastomer, to achieve motion and demonstrate many features that are similar to that of mammalian muscle.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Pneumatic Microvalve-Based Hydrodynamic Sample Injection for High-Throughput, Quantitative Zone Electrophoresis in Capillaries

A hybrid microchip/capillary CE system was developed to allow unbiased and lossless sample loading and high throughput repeated injections. This new hybrid CE system consists of a polydimethylsiloxane (PDMS) microchip sample injector featuring a pneumatic microvalve that separates a sample introduction channel from a short sample loading channel and a fused silica capillary separation column that connects seamlessly to the sample loading channel. The sample introduction channel is pressurized such that when the pneumatic microvalve opens briefly, a variable-volume sample plug is introduced into the loading channel. A high voltage for CE separation is continuously applied across the loading channel and the fused silica capillary separation column. Analytes are rapidly separated in the fused silica capillary with high resolution. High sensitivity MS detection after CE separation is accomplished via a sheathless CE/ESI-MS interface. The performance evaluation of the complete CE/ESI-MS platform demonstrated that reproducible sample injection with well controlled sample plug volumes could be achieved by using the PDMS microchip injector. The absence of band broadening from microchip to capillary indicated a minimum dead volume at the junction. The capabilities of the new CE/ESI-MS platform in performing high throughput and quantitative sample analyses were demonstrated by the repeated sample injection without interrupting an ongoing separation and a good linear dependence of the total analyte ion abundance on the sample plug volume using a mixture of peptide standards. The separation efficiency of the new platform was also evaluated systematically at different sample injection times, flow rates and CE separation voltages.

Eletrophoresis↗