Search NASA⌕ Search

SEARCH · Search NASA

Results for “POWDERED METAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Novel Route to Transition Metal Isothiocyanate Complexes Using Metal Powders and Thiourea

A new synthetic route to isothiocyanate-containing materials is presented. Eight isothiocyanate- 4-methylpyridine (y-picoline) compounds were prepared by refluxing metal powders (Mn, Fe, Co, Ni, and Cu) with thiourea in y-picoline. With the exception of compound 5,prepared with Co, the isothiocyanate ligand was generated in situ by the isomerization of thiourea to NH4+SCN- at reflux temperatures. The complexes were characterized by x-ray crystallography. Compounds 1,2, and 8 are the first isothiocyanate- 4-methylpyridine anionic compounds ever prepared and structurally characterized. Compounds 1 and 2 are isostructural with four equatorially bound isothiocyanate ligands and two axially bound y-picoline molecules. Compound 8 is a five-coordinate copper(II) molecule with a distorted square-pyramidal geometry. Coordinated picoline and two isothiocyanates form the basal plane and the remaining isothiocyanate is bound at the apex. Structural data are presented for all compounds.

Harris, Jerry D.↗
NASA NTRS1999

Pulsed high energy synthesis of fine metal powders

Repetitively pulsed plasma jets generated by a capillary arc discharge at high stagnation pressure (>15,000 psi) and high temperature (>10,000 K) are utilized to produce 0.1-10 .mu.m sized metal powders and decrease cost of production. The plasma jets impact and atomize melt materials to form the fine powders. The melt can originate from a conventional melt stream or from a pulsed arc between two electrodes. Gas streams used in conventional gas atomization are replaced with much higher momentum flux plasma jets. Delivering strong incident shocks aids in primary disintegration of the molten material. A series of short duration, high pressure plasma pulses fragment the molten material. The pulses introduce sharp velocity gradients in the molten material which disintegrates into fine particles. The plasma pulses have peak pressures of approximately one kilobar. The high pressures improve the efficiency of disintegration. High gas flow velocities and pressures are achieved without reduction in gas density. Repetitively pulsed plasma jets will produce powders with lower mean size and narrower size distribution than conventional atomization techniques.

Witherspoon, F. Douglas↗
NASA NTRS1976

Shock wave ignition of metal powders

The interaction between isolated metal particles and shock-induced flowfields is analyzed to characterize physical events and determine experimental feasibility for shock wave ignition studies. Emphasis is placed on incident shock wave phenomenon as opposed to reflected shock wave. A pre-ignition particle-flow interaction is hypothesized which presumes a vapor phase ignition reaction and an absence of significant vaporization prior to particle melting and erosion. Rapid vaporization of eroded mass is expected, with ignition reaction in the particle wakes. Experimental observation of the 6438-A Cd line and the 3721-A MgO band support the ignition mechanism hypothesized. Scattered cloud data are believed to substantiate the hypothesis that ignition delays could be correlated with predicted melting times.

Fox, T. W.↗
NASA NTRS1983

Surface characterization of Ti and Ti (6 percent, Al-4 percent, V) metal powders and interaction with primer solutions

The interaction of Ti and Ti 6-4 powders with water and primer solutions was investigated experimentally by measuring the heats of immersion. Similar comparative studies were made on anatase and rutile TiO2 powders. The surface oxide layers of Ti and Ti 6-4 cracked on heating in vacuum between 300 and 400 C as evidenced by high heats of immersion in both water and primer solutions. Polyimide and polyphenylquinoxaline interacted preferentially, compared with the solvents with both metal powders after outgassing at room temperature. The heats of immersion of Ti 6-4 in water, solvents, and primer solutions increased significantly after pretreatment of the powder by an alkaline etch and a phosphate-fluoride process. The TiO2 powders were not satisfactory models for the surface oxide layer on either Ti or Ti 6-4 powder.

Siriwardane, R. V.↗
NASA NTRS1975

Chemical reactions of metal powders with organic and inorganic liquids during ball milling

Chromium and/or nickel powders were milled in metal chlorides and in organic liquids representative of various functional groups. The powders always reacted with the liquid and became contaminated with elements from them. The milled powders had specific surface areas ranging from 0.14 to 37 sq m/g, and the total contamination with elements from the milling liquid ranged from 0.01 to 56 weight percent. Compounds resulting from substitution, addition, or elimination reactions formed in or from the milling liquid.

Arias, A.↗
NASA NTRS1985

Fluidized reduction of oxides on fine metal powders without sintering

In the process of reducing extremely fine metal particles (av. particle size or = 1000 angstroms) covered with an oxide layer, the metal particles are fluidized by a gas flow contg. H, heated, and reduced. The method uniformly and easily reduces surface oxide layers of the extremely fine metal particles without causing sintering. The metal particles are useful for magnetic recording materials, conductive paste, powder metallurgy materials, chem. reagents, and catalysts.

Hayashi, T.↗
NASA NTRS1982

Applications of high-temperature powder metal aluminum alloys to small gas turbines

A program aimed at the development of advanced powder-metallurgy (PM) aluminum alloys for high-temperature applications up to 650 F using the concepts of rapid solidification and mechanical alloying is discussed. In particular, application of rapidly solidified PM aluminum alloys to centrifugal compressor impellers, currently used in auxiliary power units for both military and commercial aircraft and potentially for advanced automotive gas turbine engines, is examined. It is shown that substitution of high-temperature aluminum for titanium alloy impellers operating in the 360-650 F range provides significant savings in material and machining costs and results in reduced component weight, and consequently, reduced rotating group inertia requirements.

Millan, P. P., Jr.↗
NASA NTRS2016

Photon Doppler Velocimeter to Measure Entrained Additive Manufactured Bulk Metal Powders in Hot Subsonic and Supersonic Oxygen Gas

Parts produced by additive manufacturing, particularly selective laser melting (SLM), have been shown to silt metal particulate even after undergoing stringent precision aerospace cleaning processes (Lowrey 2016). As printed parts are used in oxygen systems with increased pressures, temperatures, and gas velocity, the risk of ignition by particle impact, the most common direct ignition source of metals in oxygen, substantially increases. The White Sands Test Facility (WSTF), in collaboration with Marshall Space Flight Center (MSFC), desires to test the ignitability of SLM metals by particle impact in heated oxygen. The existing test systems rely on gas velocity calculations to infer particle velocity in both subsonic and supersonic particle impact systems. Until now, it was not possible to directly measure particle velocity. To increase the fidelity of planned SLM ignition studies, it is necessary to validate that the Photon Doppler Velocimetry(PDV) test system can accurately measure particle velocity.

Tylka, Jonathan↗
NASA NTRS1989

Canning Of Powdered Metal For Hot Isostatic Pressing

Quality of specimen enhanced by improved canning process. Method developed for canning specimens for hot isostatic pressing. Specimen placed inside refractory-metal ring, then sandwiched between two refractory-metal face sheets. Assembly placed inside die, then positioned in vacuum hot press. Heated to set temperature at prescribed vacuum to burn off all of binder in specimen. Advantages: powder-metallurgy composite totally purged of binder sealed in can in single operation, maintains size, shape, and uniformity of specimen. Weld region does not recrystallize, and little possibility of cracking.

Juhas, John J.↗
NASA NTRS2016

Retention of Compressive Residual Stresses Introduced by Shot Peening in a Powder Metal Disk Superalloy

The fatigue lives of disk superalloys can be increased by shot peening their surfaces, to induce compressive residual stresses near the surface that impede cracking there. As disk application temperatures increase for improved efficiency, the persistence of these beneficial stresses could be impaired, especially with continued fatigue cycling. The objective of this work was to study the retention of residual stresses introduced by shot peening, when subjected to fatigue and high temperatures. Fatigue specimens of powder metallurgy processed nickel-base disk superalloy ME3 were prepared with consistent processing and heat treatment. They were then shot peened using varied conditions. Strain-controlled fatigue cycles were run at room temperature and 704 C, to allow re-assessment of residual stresses.

fatigue↗
NASA NTRS2017

Systems and Methods for Designing and Fabricating Contact-Free Support Structures for Overhang Geometries of Parts in Powder-Bed Metal Additive Manufacturing

Systems and methods are provided for designing and fabricating contact-free support structures for overhang geometries of parts fabricated using electron beam additive manufacturing. One or more layers of un-melted metallic powder are disposed in an elongate gap between an upper horizontal surface of the support structure and a lower surface of the overhang geometry. The powder conducts heat from the overhang geometry to the support structure. The support structure acts as a heat sink to enhance heat transfer and reduce the temperature and severe thermal gradients due to poor thermal conductivity of metallic powders underneath the overhang. Because the support structure is not connected to the part, the support structure can be removed freely without any post-processing step.

Chou, Yuag-Shan↗
NASA NTRS1969

Improved retort for cleaning metal powders with hydrogen

Improved cleaning retort produces uniform temperature distribution in the heated zone and minimizes hydrogen channeling through the powder bed. Retort can be used for nonmetallic powders, sintering in a reducing atmosphere, and for cleaning powders in reduction atmospheres other than hydrogen.

Arias, A.↗
NASA NTRS1986

Metal powder production by gas atomization

The confined liquid, gas-atomization process was investigated. Results from a two-dimensional water model showed the importance of atomization pressure, as well as delivery tube and atomizer design. The atomization process at the tip of the delivery tube was photographed. Results from the atomization of a modified 7075 aluminum alloy yielded up to 60 wt pct. powders that were finer than 45 microns in diameter. Two different atomizer designs were evaluated. The amount of fine powders produced was correlated to a calculated gas-power term. An optimal gas-power value existed for maximized fine powder production. Atomization at gas-power greater than or less than this optimal value produced coarser powders.

Ting, E. Y.↗
NASA NTRS1993

On the development of constitutive relations for metallic powders

This article describes the development of elastic and plastic constitutive relations as functions of relative density for partially consolidated -100 mesh aluminum powder. First, measurements of yield stress as a function of stress state and relative density are described. Measurements of the plastic strain increments associated with yielding in unconstrained compression tests and elastic properties, both as functions of relative density, are also described. The experimental results are combined with the associated flow rule to show that the yield surface is asymmetric with respect to hydrostatic tension and compression. Second, it is shown that the yield stress results can be represented by a two-part (capped Drucker-Prager) yield surface. The consolidation yield surface moves along the hydrostatic stress axis during densification, while the shear yield surface approaches the Mises yield surface. For the Al powder used in the present investigation, superposition of shear stress on a hydrostatic stress state aids the densification process. However, the hydrostatic stress requirement was found to be reduced by only about 20 pct for relative densities below 0.98.

Watson, T. J.↗
NASA NTRS1993

Characteristics of products generated by selective sintering and stereolithography rapid prototyping processes

The trend in the modern global economy towards free market policies has motivated companies to use rapid prototyping technologies to not only reduce product development cycle time but also to maintain their competitive edge. A rapid prototyping technology is one which combines computer aided design with computer controlled tracking of focussed high energy source (eg. lasers, heat) on modern ceramic powders, metallic powders, plastics or photosensitive liquid resins in order to produce prototypes or models. At present, except for the process of shape melting, most rapid prototyping processes generate products that are only dimensionally similar to those of the desired end product. There is an urgent need, therefore, to enhance the understanding of the characteristics of these processes in order to realize their potential for production. Currently, the commercial market is dominated by four rapid prototyping processes, namely selective laser sintering, stereolithography, fused deposition modelling and laminated object manufacturing. This phase of the research has focussed on the selective laser sintering and stereolithography rapid prototyping processes. A theoretical model for these processes is under development. Different rapid prototyping sites supplied test specimens (based on ASTM 638-84, Type I) that have been measured and tested to provide a data base on surface finish, dimensional variation and ultimate tensile strength. Further plans call for developing and verifying the theoretical models by carefully designed experiments. This will be a joint effort between NASA and other prototyping centers to generate a larger database, thus encouraging more widespread usage by product designers.

Cariapa, Vikram↗
NASA NTRS1976

Ternary boride product and process

A hard, tough, strong ceramic body is formed by hot pressing a mixture of a powdered metal and a powdered metal diboride. The metal employed is zirconium, titanium or hafnium and the diboride is the diboride of a different member of the same group of zirconium, titanium or hafnium to form a ternary composition. During hot pressing at temperatures above about 2,000.degree.F., a substantial proportion of acicular ternary monoboride is formed.

Clougherty, Edward V.↗
NASA NTRS1979

Development of economical improved thick film solar cell contact

Materials were surveyed to provide candidates for an all metal electrode paste system. These consisted of a major constituent metal powder, a low melting metal powder suitable for a liquid phase sintering medium, and a powder material suitable as an etchant for silicon dioxide at sintering temperatures. By means of thermal gravimetric analysis a suitable binder was identified for low temperature fired inks. The all metal ink concept was first demonstrated with the silver system to avoid the problems of limited process windows encountered with base metal systems. A number of solid materials capable of selectively etching silicon dioxide at modest temperatures were identified. A paste with silver fluoride was screened onto N-type silicon with 5 ohm cm resistivity. The resulting contact pads had excellent adhesion but were not electrically ohmic. Metallurgically, these contacts have equal or better grain structure as commercial inks fired at the same temperatures.

Ross, B.↗