Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRECIPITATION HARDENING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Formation of the {gamma}ʹʹʹ-Ni2(Cr, Mo, W) phase during a two-step aging heat treatment in HAYNES® 244® Alloy

Precipitation hardening is the dominant method of achieving high strength in most Ni-based superalloys. The formation of nanoscale precipitates during thermal exposure is often studied to determine the optimal methods of attaining high strength. The commercial Ni-based superalloy, HAYNES® 244® alloy, is strengthened through a novel -Ni2(Cr, Mo, W) intermetallic phase that forms during a two-step aging cycle. The precipitation kinetics of this intermetallic phase are sluggish for single-step aging in comparison to the γʹ phase in precipitation-strengthened Ni-based alloys, but a two-step aging treatment has shown to reliably harden the alloy and improve high-temperature properties compared to a single-step aging heat treatment. To investigate the formation and coarsening of this phase, heat-treated samples of the 244 alloy were analyzed with high-energy in situ and ex situ X-ray techniques such as small angle X-ray scattering and wide angle X-ray scattering as well as Vickers micro-hardness, electron microscopy, and atom probe tomography. The relationship between hardness, aging parameters, and microstructure evolution is discussed. The enthalpy of formation and precipitate solvus temperature were determined with high-temperature differential scanning calorimetry and dilatometry analysis.

Ni-based Superalloys↗
DOE OSTI2020

Coupled solute effects enable anomalous high-temperature strength and stability in nanotwinned Al alloys

Nanoprecipitates or grain refinement can effectively enhance the mechanical strength of Al alloys, but the room-temperature strengths of precipitation hardened and nanocrystalline Al alloys often fall below 1 GPa. Furthermore, they are largely plagued by precipitous mechanical softening at elevated temperature below 300°C, mostly due to degraded microstructural stability. Here, we report a mechanism of coupled solute effect in nanotwinned Al-Fe-Ti alloys that enables stability of nanograins up to 400°C and an unprecedented high-temperature flow stress of ~ 1.7 GPa at 300°C. The supersaturated Fe solutes in Al act as effective grain refiner, forming superstrong solid solution alloys. More importantly, empirical evidence combined with first principle calculations indicate that the Ti solutes delay the agglomeration of Fe solutes, thereby remarkably extending the temperature window for the stability of nanograins in nanotwinned Al alloys. Finally, this study highlights the opportunity to design ultrastrong and stable nanostructured alloys for potential high temperature applications via a coupled solute effect.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase transformation dynamics guided alloy development for additive manufacturing

Fusion-based additive manufacturing technologies enable the fabrication of geometrically and compositionally complex parts unachievable by conventional manufacturing methods. However, the non-uniform and far-from-equilibrium heating/cooling conditions pose a significant challenge to consistently obtaining desirable phases in the as-printed parts. Here, in this study, we report a martensite stainless steel development guided by phase transformation dynamics revealed by in-situ high-speed, high-energy, high-resolution X-ray diffraction. This developed stainless steel consistently forms desired fully martensitic structure across a wide range of cooling rates (10 2 –10 7 °C/s), which enables direct printing of parts with fully martensitic structure. The as-printed material exhibits a yield strength of 1157 ± 23 MPa, comparable to its wrought counterpart after precipitation-hardening heat-treatment. The as-printed property is attributed to the fully martensitic structure and the fine precipitates formed during the intrinsic heat treatment in additive manufacturing. The phase transformation dynamics guided alloy development strategy demonstrated here opens the path for developing reliable, high-performance alloys specific for additive manufacturing.

17–4 PH stainless steel↗
DOE OSTI2020

High susceptibility to adiabatic shear banding and high dynamic strength in tungsten heavy alloys with a high-entropy alloy matrix

The susceptibility to adiabatic shear banding (ASB) of tungsten heavy alloys (WHAs) is a key factor to determine their penetration performance for kinetic energy penetrators (KEPs). This work reports a novel WHA with strong susceptibility to ASB that uses a precipitation-hardening high-entropy alloy (HEA) as the binding phase of W particles. The results find that nanoscale L12 precipitates and high dislocation density in the matrix contribute a high dynamic yield strength of ~2300 MPa. Also, a narrow ASB with a width of ~12 μm forms in the novel WHA, which is only 6% of the width of ASB in traditional WHAs like W-NiFe, exhibiting a great susceptibility to ASB. The redissolution of precipitates into the matrix because of temperature rise during shearing could sharply soften the shearing location, which is suggested to be a very important factor of destabilizing mechanism to promote the development of ASB.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Report on Evolution of Inconel 718 Following HFIR Irradiation

The report presents the microstructure and mechanical properties of 3D printed Inconel 718 after irradiation in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) to assess its potential use as a structural material. The structural components near the outlets of several proposed reactor cores will experience significant neutron fluxes and outlet coolant temperatures ranging from the hot standby temperature of 300 °C to nearly 550 °C at the center of the part. These components must support the core in appropriate loading conditions and require structural analysis at relevant temperatures. In FY21, three heat treatments were designed and conducted to simplify the microstructure and to determine how each precipitating phase contributed to the overall strength. In FY21, baseline mechanical properties were measured from uniaxial tensile tests on subsize SS-J2 specimens at room temperature and at elevated temperatures of 300, 450, and 600 °C to serve a comparison to the irradiated properties. Four capsules containing 3D printed Inconel 718 were inserted into HFIR in FY21 for a matrix of two temperatures and two doses. The lower of the two doses was available for characterization in FY22. Multiple heat treatments of Inconel 718 irradiated to nominal conditions of 2 displacements per atom (dpa) at either 300 or 600 °C were strained with uniaxial tensile tests at the Irradiated Material Examination and Testing (IMET) Facility to discern the mechanical properties. Transmission electron microscopy was performed to correlate the observed mechanical properties with nanoscale features. The initially homogenous AM718-HM increased in strength at both irradiation temperatures based on a high density of nanometer-scale radiation-induced cavities at lower temperature and nucleation and growth of γ" precipitates at higher temperatures. The precipitate-hardened AM718-HT2 showed very small differences in strength before and after irradiation: the contribution to strength from γ" precipitates was replaced with dislocation loops. Because the radioactivity of the nickel superalloys from neutron activation limited the scope of the analysis, a feasibility study examined the possibility of an ultra-miniature specimen geometry, colloquially SS-Tiny (SS-T), for mechanical property determination using the nonirradiated Inconel 718. This study found an overestimation of ductility from the SS-T geometry with yield strength and ultimate tensile strength slightly above the SS-J2 geometry: this could be contributed to a reduction in specimen thickness.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Precipitate Characterization in Model Al-Zn-Mg-(Cu) Alloys Using Small-Angle X-ray Scattering

Model 7000 series alloys with and without copper were fabricated into sheets to study precipitation hardening behavior under isothermal aging conditions. Samples of each alloy were subjected to 3 h annealing treatments at various temperatures to produce a range of precipitate size distributions. Hardness, electrical conductivity, and small-angle X-ray scattering (SAXS) were used to characterize the aging behavior of the two alloys. Precipitate size distributions were modeled from the scattering curves for each annealing condition using a maximum entropy method (MEM) and compared to select transmission electron microscopy (TEM) results. The measured average precipitate diameters from TEM were in good agreement with the average precipitate diameters determined from the scattering curves.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Role of Fe in long-range ordered Ni 2 Cr precipitates in Ni-Cr-Fe model alloys during isothermal aging

The precipitation of new phases during long-term service at elevated temperatures is a concern for the thermal stability of engineering alloys. In Ni-Cr-based alloys, e.g., Alloy 690, the formation of long-range ordered Ni 2 Cr causes embrittlement and may impact the lifetime of nuclear power plant components. In this work, we quantify the formation and evolution of Ni 2 Cr precipitation in eleven Ni-Cr-Fe model alloys with 0, 5, 7, and 10wt % Fe contents, and with Ni/Cr atomic ratios of 1.8, 2.0, 2.2, 2.4. These alloys were isothermally aged up to 10,000h at temperatures between 330 and 475°C. The alloys were characterized by synchrotron-based x-ray diffraction and Vickers hardness testing to quantify Ni 2 Cr precipitate size, and the impact of precipitate size on the mechanical properties as a function of Fe content. After 10,000 h of aging at 475°C and 418°C, the formation of Ni 2 Cr was observed in all alloys with 0 and 5wt % Fe. After 10,000h of aging at 418°C, Ni 2 Cr precipitates were also observed in the 7wt % Fe containing Ni/Cr=2.0 sample. Further, no clear evidence of Ni 2 Cr was observed in any of the 10wt % Fe samples at any time and temperature combination. We find that the face-centered cubic matrix lattice contraction and Vickers hardness are correlated with the Ni 2 Cr formation. The greatest change in hardness and lattice contraction occurs in stoichiometric alloys (Ni/Cr=2.0) with 0wt % Fe at 475°C. The rate of change in the material properties for the 5wt % Fe alloys is reduced, however the magnitude of changes is similar to 0wt % Fe alloys. A precipitation hardening model developed for Ni-Cr alloys based on critical resolved shear stress with weakly coupled dislocations shows a clear link between Ni 2 Cr precipitate size and hardness. This trend held across all alloys with Ni 2 Cr formation regardless of Fe concentration. This important structure-property relationship can potentially help define Ni-Cr-Fe-based component lifetimes directly through an understanding of how Ni 2 Cr formation impacts mechanical properties as a function of Fe content.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Evolution of carbide precipitates in Haynes® 282 superalloy processed by wire arc additive manufacturing

Precipitation hardening regulated with heat treatments is a critical technique for tuning the mechanical properties of Ni-based superalloys fabricated with additive manufacturing, where mechanical deformation is no longer viable for microstructural refinement. As one of the key precipitates, carbides prevail in the additively manufactured alloys, whose precipitation kinetics remain largely vague. This work studies the influence of heat treatments on the evolution of MC- and M 23 C 6 -type carbides within a Haynes® 282 superalloy prepared by wire arc additive manufacturing (WAAM). SEM-EDS analysis was performed to identify the evolution pathways of the carbides, and TEM and XRD characterizations were carried out to track the crystallographic features. The MC-type carbides are originally present in the as-printed alloy, which distribute uniformly across the whole material and remain largely unchanged in size during the heat treatments. By contrast, the incipiently non-existent M 23 C 6 -type carbides precipitate during an aging treatment at 1010 °C, which majorly extend along the grain boundaries as kinetically feasible sites. Further experimental and computational analysis confirms the enhancing effect of the M 23 C 6 -type carbides on the Vickers hardness. For the first time, this work revealed the evolution pathways of carbides within a Haynes® 282 superalloy prepared by WAAM, providing critical information for tunning the microstructure and mechanical properties. Finally, the carbide evolution kinetics established in this work can be potentially extended to other alloys prepared with WAAM, providing critical information to prevent mechanical failures associated with carbide coarsening.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Partitioning of Ca to metastable precipitates in a Mg-rare earth alloy

The potential effect of the element Ca on the precipitation behavior was investigated in an Mg-rare earth alloy. A combination of metastable β''' and β' precipitates was observed for the peak aging condition at 200°C. Ca addition was found to have no significant effect on the precipitating phases and evolution sequence. Composition analysis showed that the Ca partitioned to both β''' and β' precipitate phases. First-principles calculations indicated that Ca partitions to the rare-earth sublattice in the precipitate phase. This finding suggests the potential of Ca to partially replace costly rare-earth elements in precipitation-hardened Mg-rare earth alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of Precipitation-Strengthened Al 0.8 NbTiVM (M = Co, Ni) Light-Weight Refractory High-Entropy Alloys

Single-phase solid-solution refractory high-entropy alloys (RHEAs) have been receiving significant attention due to their excellent mechanical properties and phase stability at elevated temperatures. Recently, many studies have been reported regarding the precipitation-enhanced alloy design strategy to further improve the mechanical properties of RHEAs at elevated temperatures. In this study, we attempted to develop precipitation-hardened light-weight RHEAs via addition of Ni or Co into Al 0.8 NbTiV HEA. The added elements were selected due to their smaller atomic radius and larger mixing enthalpy, which is known to stimulate the formation of precipitates. The addition of the Ni or Co leads to the formation of the sigma precipitates with homogeneous distribution. The formation and homogeneous distribution of sigma particles plays a critical role in improvement of yield strength. Furthermore, the Al 0.8 NbTiVM 0.2 (M = Co, Ni) HEAs show excellent specific yield strength compared to single-phase AlNbTiV and NbTiVZr RHEA alloys and conventional Ni-based superalloy (Inconel 718) at elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Neutron Diffraction Residual Stress Study of a AA2219-T87 Self-Reacting Friction Stir Weld

2219-T87 is a precipitation hardenable aluminum-copper alloy which sees wide use in structural aerospace components. Thick panels of this alloy are joined via self-reacting friction welding (SRFSW); however, this thermomechanical process can result in significant loss of the alloy’s strengthening precipitates and large residual stresses which are detrimental to mechanical behavior and performance. High-resolution maps of the residual strain and stress states along the normal, transverse, and longitudinal directions of 2219-T87 SRFSW were obtained using neutron diffraction measurements. Residual stress had the highest tensile value in the heat-affected zone (HAZ) and the largest compressive stress in the base metal region of the normal and transverse directions. Line profile residual stress distributions displayed an “M”-shaped distribution in each direction with the longitudinal direction being the most pronounced while 2D residual stresses displayed an hourglass-shaped pattern. Further, average maximal longitudinal residual stress values ranged from 60.6 to 85.6% of yield. Microhardness testing across the transverse weld section produced a “V”-shaped curve with slight hardness recovery in the stir zone. Maximal and minimal microhardness values were observed in the base metal (154 HV) and thermomechanically affected zone (82 HV), respectively. Microstructural evolution was recorded using optical microscopy and showed decreasing grain size from the HAZ to the stir zone.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Atomic structures of interfacial solute gateways to θ' precipitates in Al-Cu alloys

Many materials employed in critical structural applications depend upon metastable strengthening precipitates that transform or dissolve at elevated temperatures. Herein, aberration-corrected scanning transmission electron microscopy and first-principles calculations are used to accurately determine the atomic structure of the highly mobile, semi-coherent precipitate interfaces that control this process in the classic θ' (Al 2 Cu) precipitate in the Al-Cu system. Semi-coherent {110} interfaces are found to be composed of an array of unexpected misfit dislocations that are arranged in two different structural units. Dislocations accommodate nearly all of the misfit between the Al matrix and strengthening phase. Cu is observed to segregate to the compressed edge of the dislocation cores at specific sites in this interface. First-principles calculations revealed the energetic landscape that facilitates these sites to become entry and exit gateways of Cu atoms in this semi-coherent interface. In conclusion, this investigation reveals critical features within semi-coherent interfaces that determine the thermal stability of precipitation-hardened alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Fracture characteristics and heat treatment of laser powder bed fusion additively manufactured GRCop-84 copper

Laser Powder Bed Fusion (LPBF) of Glenn Research Copper 84 (GRCop-84), a Cr 2 Nb (8 at. % Cr, 4 at. % Nb) precipitation hardened alloy, produces a fully dense high conductivity alloy with a yield strength of 500 MPa and ultimate tensile strength (UTS) of 740 MPa, superior to other competing copper alloys, and 20% elongation at fracture for material stressed perpendicular to the build direction. The high thermal stability of the Cr 2 Nb precipitate in the copper matrix reduces coarsening and maintains a 300 MPa yield, 520 MPa UTS and 26% elongation after a 900 °C, 5-h heat treatment, while a 3 h 450 °C heat treatment increases yield to 810 MPa, UTS to 970 MPa with 9% elongation at fracture, for samples stressed perpendicular to the build direction. Tensile strength anisotropy based on print direction was attributed to internal stress and columnar grain formation. Void nucleation during tensile fracture was initiated by brittle fracture of precipitate particles within the copper matrix. Fracture cusps contain matching precipitate fragment geometry on opposing sides located near the cusp center in at least 80% of fracture cusps. An optimal precipitate size of 100 nm is predicted for maximum tensile strength from precipitates on fracture surfaces, while tensile testing with varying heat treatments shows maximum strength with 100 nm and smaller precipitates. Cr2Nb precipitates are shown to transition between polycrystalline and monocrystalline structures at high temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Laser Powder Directed Energy Deposition of Steels for Nuclear Applications

This comprehensive investigation examines the structure–property relationships in two nuclear alloy systems—Alloy 709 (A709) austenitic stainless steel and Grade 92 (G-92) ferritic/martensitic (F/M) steel—manufactured via directed energy deposition (DED) for sodium-cooled fast reactor applications. This study establishes the fundamental mechanisms for controlling microstructures for optimizing the mechanical performance of additively manufactured nuclear materials through systematic heat treatment optimization and multiscale characterization. As-deposited A709 steel develops a complex multiscale strengthening architecture consisting of a fine cellular solidification structure with diameter of 2-3 µm within10–50 µm grains, elevated dislocation densities from rapid thermal cycling, and grain boundary precipitates that activate concurrent Hall–Petch, dislocation, and precipitation hardening mechanisms to achieve exceptional properties [yield strength (YS): 603 MPa, ultimate tensile strength (UTS): 844 MPa, Vickers hardness: 220 HV] that achieve a 44% superior strength compared to that of the wrought material. Heat treatments produce different results. Solution annealing (SA) dissolves the cellular structure and reduces the hardness to 190 HV. Precipitation treatment (PT) keeps the cellular structure but adds carbides, allowing the hardness to reach 205 HV. The best approach combines both treatments (SA+PT) and creates uniform precipitate distributions with M 23 C 6 carbides at the grain boundaries and MX carbonitrides in the matrix, achieving a hardness of 195 HV. However, directional differences persist, with a 12%–15% strength variation between orientations due to the inherited layered microstructural architecture that survives aggressive heat treatment. While tensile testing at 550°C demonstrates 40%–50% thermal softening with dynamic strain aging, DED A709 steel still maintains a 71% higher YS than that of the wrought material. Ion irradiation studies (100–400 dpa) of DED A709 steel reveal progressive radiation damage with increasing void density and radiation-induced segregation causing nickel enrichment and chromium depletion, which will ultimately compromise mechanical properties. As-deposited G-92 exhibits exceptional strength (UTS: 1650–1700 MPa, 430 HV) through a complex microstructure containing both ferrite and martensite phases, a high geometrically necessary dislocation (GND) density (17.04×10 14 /m 2 ), and fine carbides. Heat treatments create distinct changes. Normalizing produces fresh martensite with the highest hardness (460 HV) and an increased GND density (20.23×10 14 /m 2 ). Tempering develops dual precipitation systems and reduces the hardness to 290 HV. The optimal approach uses sequential normalizing plus tempering, achieving balanced properties with the lowest hardness (250 HV) and a reduced GND density (11.01×10 14 /m 2 ). A processing-dependent anisotropy is observed: horizontal specimens achieve superior ductile behavior, while vertical specimens exhibit brittle failure. A tempering heat treatment successfully mitigates this anisotropic behavior by transforming the hard martensitic as-deposited structure into tempered martensite enabling both horizontal and vertical specimens to exhibit similar stress–strain characteristics with visible necking behavior. Remarkably, testing at 550°C reveals a reversal in the anisotropy, where as-deposited specimens achieve near isotropy with superior thermal stability (a 15%–20% strength reduction), while tempered specimens develop an orientation dependence with a 25%–30% strength reduction. Both alloy systems demonstrate that DED processing creates specimens with a superior strength through refined microstructural features, though with distinct strengthening mechanisms—austenitic through cellular structures and precipitates versus F/M through phase transformations and precipitates. Heat treatment optimization requires alloy-specific approaches, with A709 benefiting from controlled precipitation while G-92 requires careful phase transformation control. The results show that DED manufacturing can produce nuclear materials with exceptional performance, but directional effects and temperature-dependent behavior must be carefully considered for reactor component design and qualification.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Microstructural evolution and hardness changes in ion irradiated nickel-based Haynes 282 superalloy

This study investigated the crucial aspects of thermal and irradiation stability in precipitation hardened Haynes 282 Ni-based superalloy. The Haynes 282 Ni-based alloy was irradiated by 8 MeV Ni 3+ ions to assess its resistance to phase instabilities and mechanical property alterations. The mid-range doses (at a depth of ∼1 µm) were 1 and 10 displacements per atom (dpa) at temperatures of 600°C and 750°C. Nanoindentation tests provided insights into bulk equivalent hardness of the irradiated and pristine regions, while scanning transmission electron microscopy (STEM) and energy dispersive X-ray spectroscopy (EDS) were used to examine the microstructural evolution of irradiation-induced defects and γ′ -Ni 3 (Al, Ti) precipitates and defect structure under irradiation. These precipitates, with an average diameter of 29 nm and a number density of 5 x 10 21 /m 3 , acted as robust dispersion strengthening agents with high radiation point defect sink strength. Remarkably, irradiation did not significantly alter the size or number density of the γ′ precipitates, indicating exceptional thermal stability and radiation resistance of these precipitates at the examined conditions. Radiation-induced dislocation loops were observed at 600°C, albeit without a substantial impact on mechanical properties due to the dominance of γ′ precipitates on the overall alloy strength. The superior stability of γ′ precipitates observed in this study contrasts with several previous research findings on Ni-based alloys that reported poor precipitate stability. Plausible reasons for this difference are discussed. Moreover, this work explicitly outlines a physically grounded approach to ensure accurate microstructure-hardness correlations and clarifies the hardening model by addressing common misapplications of superposition in prior studies.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Nuclear response of additive manufactured GRCop-84 copper for use in Lower hybrid launchers in a fusion environment

Recent advances in selective laser melting (SLM) 3D printing technology allow additive manufacture of lower hybrid current drive (LHCD) RF launchers from a new material, Glenn Research Copper 84 (GRCop-84), a Cr 2 Nb (8 at. % Cr, 4 at. % Nb) precipitation hardened alloy, in configurations unachievable with conventional machining. Tensile strength and thermal conductivity are compared to other competing high conductivity copper alloys for fusion use. Swelling and conductivity at 100 DPA when exposed to the Hanford Fast Flux Test Facility neutron spectrum is predicted in the 1–2 % and 65-70% IACS range, respectively, by comparison to copper alloys with similar precipitate and grain size. Finally, self-similar ion irradiation of a GRCop-84 target at 430 °C to 20 DPA resulted in no noticeable void formation in FIB cross sections or TEM lamella.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

The formation and evolution of Ni 2 Cr precipitates in Ni–Cr model alloys as a function of stoichiometry characterized by synchrotron x-ray diffraction

Ni-based alloys containing significant amounts of Cr, may precipitate new phases during long-term service at elevated temperatures. In Ni–Cr model alloys, the formation of Ni 2 Cr has been found to impact the material properties, including the strength and ductility after isothermal aging below the critical temperature of 590°C. In this work, we quantify the formation and evolution of long-range ordering in four Ni–Cr binary model alloys (Ni/Cr = 1.8, 2.0, 2.2, 2.4) after isothermal aging up to 10,000h at temperatures between 373 and 475°C. The alloys were characterized by hardness testing and synchrotron-based x-ray diffraction to quantify the impact of Ni 2 Cr phase fraction and precipitate size on mechanical properties. After 500h of isothermal aging, the formation of Ni 2 Cr was detected in all four alloys at 475°C. In the stochiometric alloy samples (Ni/Cr = 2.0), the formation of Ni 2 Cr was found after 500 and 3000h aging at 418 and 373°C, respectively. We found that the matrix lattice contraction and Ni 2 Cr phase fraction both saturate after early aging times. This is in stark contrast to the hardness and Ni 2 Cr precipitate size that both continue to increase with increasing aging time. Our results highlight that changes in hardness correlate linearly with Ni 2 Cr precipitate size rather than phase fraction. This important structure-property relationship can potentially help define Ni–Cr-based component lifetimes directly through an understanding of how Ni 2 Cr formation impacts strength and ductility. Here, we find that a precipitation hardening model for critical resolved shear stress with weakly coupled dislocations shows good agreement with the material property changes quantified from experimental measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Revisiting the first Sandia Fracture Challenge with transient deformation heating and strain localization considerations

In this study, we present a systematic experimental study and accompanying theoretical analysis of the dependence of ductile fracture on strain localization, strain hardening rates, deformation-induced thermal softening, and transient heat conduction under spatially uniform as well as spatially heterogeneous deformation. Spatially uniform cases are studied via standard dogbone shaped specimens subject to uniaxial tension. Spatially heterogeneous deformation is studied via the so-called Sandia Fracture Challenge (SFC) specimen, which is a standard compact tension specimen modified with three machined holes in front of a blunt notch. We utilize the same precipitation hardened martensitic stainless steel used in the first SFC experiments, i.e. 15-5 PH with an H1075 heat treatment. We also study 15-5 PH in Condition A and with the H900 heat treatment, each of which has a different hardening behavior and ductility. We find that the ductility does not correlate with the deformation to first crack initiation in the SFC specimen. Instead, hardening rates are better correlated. Moreover, a re-examination finds that an accurate calibration of the hardening rates is strongly correlated with accurate blind predictions of ductile fracture in the SFC specimens. Given that thermal softening can greatly affect hardening rates, we provided a thermographic analysis of deformation-induced heating and transient heat transfer in both the dogbone shaped samples and the SFC specimens. Transient heating in stainless steels is found to have first-order effects on the strain at the onset of necking, strain to fracture, as well as strain localization and ductile fracture in complex geometries even under so-called quasi-static loading rates.

42 ENGINEERING↗