Search NASA⌕ Search

SEARCH · Search NASA

Results for “Phase patterning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

LISA Telescope Sensitivity Analysis

The results of a LISA telescope sensitivity analysis will be presented, The emphasis will be on the outgoing beam of the Dall-Kirkham' telescope and its far field phase patterns. The computed sensitivity analysis will include motions of the secondary with respect to the primary, changes in shape of the primary and secondary, effect of aberrations of the input laser beam and the effect the telescope thin film coatings on polarization. An end-to-end optical model will also be discussed.

Waluschka, Eugene↗
NASA NTRS2004

DORIS satellite antenna maps derived from long-term residuals time series

Recent studies have shown that phase pattern models for the Jason-1 GPS antenna significantly benefit GPS-based precise orbit determination (POD) for the satellite. We have used a similar technique to derive DORIS receiver antenna maps, using all available DORIS tracking data over long time periods (from 1993.0 to 2004.0). We demonstrate that the derived correction models are satellite specific. For a given satellite, year-to-year estimations show clear systematic patterns. Some of these systematic patterns are attributable to the derivative of the multi-path effects in the direction of the satellite velocity. For early SPOT data, the patterns can be explained by an offset in the TAI time tagging (typically 8 (mu)s). In a second step, we have applied the SPOT2 antenna correction models in precise orbit determination and in the positioning of ground beacons. Preliminary results on DORIS/SPOT2 show that application of the DORIS antenna maps lead to a slight improvement of the derived POD and geodetic results (typically less than 5%).

precise orbit determination (POD)↗
NASA NTRSDate not supplied

3D Phase-Field Simulations of Pattern Formation During Freeze Casting

We present the results of a combined experimental and phase-field modeling study of pattern formation during freeze casting. Those studies use unidirectional freezing of simple binary liquid mixtures of water and sugars (sucrose and trehalose) in a temperature gradient, which suffice to produce hierarchical templated structures similar to those observed in more complex multi-component freeze-cast systems including lamellae, undulated ridges, and more exotic “jellyfish-like” substructures. Multiscale 3D phase-field simulations reproduce remarkably well those structures quantitatively and identify key properties of the ice-water interface that control their formation. They further reveal that lamellae form as a result of a novel symmetry-breaking secondary instability of partially faceted cellular structures and pinpoint additional secondary instability mechanisms giving rise to smaller-scale substructures.

Kaihua Ji↗
NASA NTRSDate not supplied

3D Phase-Field Simulations of Pattern Formation During Freeze Casting

We present the results of a combined experimental and phase-field modeling study of pattern formation during freeze casting. Those studies use unidirectional freezing of simple binary liquid mixtures of water and sugars (sucrose and trehalose) in a temperature gradient, which suffice to produce hierarchical templated structures similar to those observed in more complex multi-component freeze-cast systems including lamellae, undulated ridges, and more exotic “jellyfish-like” substructures. Multiscale 3D phase-field simulations reproduce remarkably well those structures quantitatively and identify key properties of the ice-water interface that control their formation. They further reveal that lamellae form as a result of a novel symmetry-breaking secondary instability of partially faceted cellular structures and pinpoint additional secondary instability mechanisms giving rise to smaller-scale substructures.

Kaihua Ji↗
NASA NTRS2023

Experimental Investigation of Flow Orientation Effects on Cryogenic Flow Boiling

Cryogenic flow boiling physics is of paramount importance for future cryogenic space applications employing Cryogenic Fluid Management (CFM) technologies. This experimental study investigates the two-phase flow and heat transfer performance of LN 2 flow boiling across five distinct flow orientations: vertical upflow, vertical downflow, horizontal flow, 45° inclined upflow, and 45° inclined downflow. The study employed the steady- state heating method within a circular heated tube featuring an 8.5-mm inner diameter and a 680-mm heated length. High-speed video recordings were utilized to capture two-phase flow patterns and interfacial behaviors across various flow orientations. The experiments covered a wide range of operating conditions, including mass velocities ranging from 351.80 to 1572.77 kg/m 2 s and inlet pressures from 297.14 to 1032.97 kPa, primarily with near-saturated inlet subcooling. Distinct two-phase flow patterns and regime transitions were identified for each flow orientation. Symmetrical flow patterns were evident in vertical orientations, whereas non-vertical orientations exhibited asymmetric flow stratifications, primarily influenced by the buoyancy force in a terrestrial gravity environment. Bubble dynamic parameters were quantified, and bubble collision and dispersion phenomena were visualized. Analyzing heat transfer performance based on local flow boiling curves and variations in heat transfer coefficients (HTCs), it was observed that vertical upflow demonstrated the most enhanced heat transfer performance, while vertical downflow exhibited the lowest. As mass velocity exceeded 830 kg/ m 2 s, the differences in heat transfer among orientations became less distinct, emphasizing the role of flow inertia in mitigating the influence of flow orientation. A direct comparison of microgravity HTC data from a recent study by the authors against the 1-𝘨 e HTC data indicated enhanced heat transfer performance in microgravity for flow orientation configurations in terrestrial gravity. However, this enhancement progressively diminished as the heat flux increased. Distinct HTC trends were observed as mass velocity increased for different flow orientations and gravity levels.

Cryogens↗
NASA NTRS1987

Time evolution of pulsed far-field patterns of GaAlAs phase-locked laser-diode arrays

The time evolution of pulsed far fields from commercially available gain-guided phase-locked arrays has been studied and compared to experimental results previously obtained by streak camera measurements, and to predictions of coupled-mode theories developed for index- and gain-guided arrays. Although phase locking is evident by 100 ps into the drive pulse, stable operation in a fixed superposition of array modes is not achieved until 1-2 ns after the drive pulse has stabilized.

Forrest, Kathrine A.↗
NASA NTRS2010

Operation Program for the Spatially Phase-Shifted Digital Speckle Pattern Interferometer - SPS-DSPI

SPS-DSPI software has been revised so that Goddard optical engineers can operate the instrument, instead of data programmers. The user interface has been improved to view the data collected by the SPS-DSPI, with a real-time mode and a play-back mode. The SPS-DSPI has been developed by NASA/GSFC to measure the temperature distortions of the primary-mirror backplane structure for the James Webb Space Telescope. It requires a team of computer specialists to run successfully, because, at the time of this reporting, it just finished the prototype stage. This software improvement will transition the instrument to become available for use by many programs that measure distortion

Blake, Peter N.↗
NASA NTRS2018

Estimating a Large Phased Array Antenna Radiation Pattern by Computer Electromagnetic Simulation

The design of a conformal antenna for use on UAV's (Unmanned Aerial Vehicle) and other aircraft can be enhanced with computational electromagnetic modeling to determine the expected radiation patterns of the antenna when mounted on the aircraft. However, detailed simulation of the antenna structure and the aircraft together requires significant computational resources and time which may not be available. This paper details several methods for estimating the radiation pattern of a 50 by 50-element patch antenna. The Conformal Lightweight Antenna Structures for Aeronautical Communication Technologies (CLASACT) Program aims to build and test a 14.25 gigaherz (Ku-band) conformal antenna on a NASA-owned UAV. The antenna is intended for satellite communications and will enable communication between a ground station and a UAV when the separation distance is too great for line-of-sight communication. It is estimated that a 2 degree beamwidth will be necessary, requiring a 50 by 50 array of patch elements. The narrow beamwidth requirement, together with an element spacing of 0.6 lambda means that the array length will be 30 wavelengths, electrically very large. Three methods of varying complexity are described for estimating the total far-field radiation pattern. The results are shown for each method in the form of a normalized power pattern.

Mackenzie, Anne I.↗
NASA NTRS1999

The Effects of LOX Post Biasing on SSME Injector Wall Compatibility

An experimental investigation has been carried out to examine the effects of LOX post biasing of a shear coaxial injector on the behavior of the spray near a chamber wall. The experimental work was performed with inert propellant simulants in a high-pressure chamber. Injector flow rates and chamber pressure were designed to match the Space Shuttle Main Engine (SSME) injector gas-to-liquid density and velocity ratio at the point of propellant injection. Measurements of liquid mass flux, gas phase velocity and droplet size were made using mechanical patternation and phase Doppler interferometry techniques. The measurements revealed that the liquid mass flux distribution shifts away from the wall with increasing LOX post bias away from the wall. The shift in the liquid flux distribution was much greater than that caused by the angling of the LOX post alone. Gas velocity near the wall simultaneously increased with increasing LOX post bias away from the wall. The increase in wall side gas velocity was due to the higher fraction of gas injected on the wall side of the injector as a result of the eccentricity at the injector exit. The net result is a decrease in mixture ratio near the wall. Estimates of heat transfer and engine performance relative to the unbiased case are presented.

Strakey, P. A.↗
NASA NTRS1980

Multi-mode horn antenna simulation

Radiation patterns were computed for a circular multimode horn antenna using waveguide electric field radiation expressions. The circular multimode horn was considered as a possible reflector feed antenna for the Large Antenna Multifrequency Microwave Radiometer (LAMMR). This horn antenna uses a summation of the TE sub 11 deg and TM sub 11 deg modes to generate far field primary radiation patterns with equal E and H plane beamwidths and low sidelobes. A computer program for the radiation field expressions using the summation of waveguide radiation modes is described. The sensitivity of the multimode horn antenna radiation patterns to phase variations between the two modes is given. Sample radiation pattern calculations for a reflector feed horn for LAMMR are shown. The multimode horn antenna provides a low noise feed suitable for radiometric applications.

Dod, L. R.↗
NASA NTRS1992

Dehydration kinetics and thermochemistry of selected hydrous phases, and simulated gas release pattern in carbonaceous chondrites

As part of our continued program of study on the volatile bearing phases and volatile resource potential of carbonaceous chondrite, results of our experimental studies on the dehydration kinetics of talc as a function of temperature and grain size (50 to 0.5 microns), equilibrium dehydration boundary of talc to 40 kbars, calorimetric study of enthalpy of formation of both natural and synthetic talc as a function of grain size, and preliminary results on the dehydration kinetics of epsomite are reported. In addition, theoretical calculations on the gas release pattern of Murchison meteorite, which is a C2(CM) carbonaceous chondrite, were performed. The kinetic study of talc leads to a dehydration rate constant for 40-50 microns size fraction of k = (3.23 x 10(exp 4))exp(-Q/RT)/min with the activation energy Q = 376 (plus or minus 20) kJ/mole. The dehydration rate was found to increase somewhat with decreasing grain size. The enthalpy of formation of talc from elements was measured to be -5896(10) kJ/mol. There was no measurable effect of grain size on the enthalpy beyond the limits of precision of the calorimetric studies. Also the calorimetric enthalpy of both synthetic and natural talc was found to be essentially the same, within the precision of measurements, although the natural talc had a slightly larger field of stability in our phase equilibrium studies. The high pressure experimental data the dehydration equilibrium of talc (talc = enstatite + coesite + H2O) is in strong disagreement with that calculated from the available thermochemical data, which were constrained to fit the low pressure experimental results. The calculated gas release pattern of Murchison meteorite were in reasonable agreement with that determined by stepwise heating in a gas chromatograph.

Bose, Kunal↗
NASA NTRS1992

Coarsening following a morphological instability in the one-sided model

We study the coarsening of the interfacial pattern separating two coexisting phases after the pattern becomes morphologically unstable. Shortly after the instability, the scale of the structure is given by the most unstable wave number in the linear regime. At later times, nonlinear interactions cause the structure to coarsen. Coarsening is studied by monitoring the time dependence of the two-dimensional power spectrum of the pattern, especially for wave vectors transverse to the direction of growth. Characteristic length scales of the pattern obtained from moments of the power spectrum are asymptotically linear in time. Furthermore, the power spectrum is seen to satisfy a scaling relation, in agreement with previous studies. A normal-velocity autocorrelation function is calculated and found to decay substantially over length scales that are of the order of the scale of the pattern. The issue of spatial anisotropy in the correlation functions is also discussed.

Vinals, Jorge↗
NASA NTRS1988

A micromechanics model for the effective Young's modulus of a piecewise-isotropic laminate with wavy patterns

A mathematical model based on the Euler-Bernoulli beam theory is proposed for predicting the effective Young's moduli of piece-wise isotropic composite laminates with wavy patterns in the main load-carrying layers. Strains in corrugated layers, in-phase layers, and out-of-phase layers are predicted for various geometries and material configurations by assuming matrix layers as elastic foundations. Experimental results obtained from corrugated aluminum specimens and aluminum/epoxy specimens with in-phase and out-of-phase wavy patterns coincide very well with the predictions. The work represents a preliminary effort toward further generalization of the model for two-dimensional anisotropic laminates containing wavy patterns in the main load-carrying layers.

Lee, Jong-Won↗
NASA NTRS1974

Moonquake predetermination and tides

A pattern in moonquakes, which correlates with the monthly tidal cycle, also correlates with a phase-shifted pattern of a 7-month tidal cycle. The lead of approximately 2 months in moonquake occurrence can be explained if local tidal forces are combined with a moonquake-driving force. This force, assumed to result from the 6-yr physical libration in latitude, would cause N-S sliding of an outer layer across a solid layer within a decoupled core in a lunar model. During 1969-1971, the sliding would be southward with a progression of monthly maxima in the combined forces. Where these forces control moonquakes, the reversal in direction of the 6-year cyclic force in early 1972 should cause a minimum in moonquake activity. Decreases toward such a minimum did occur simultaneously in the similar progressions of monthly moonquakes and maxima in the combined forces at the most active hypocenter. Repetition of the 1966-1971 force pattern in 1975-1977 should produce a corresponding repetition of the moonquake pattern.

Chapman, W. B.↗
NASA NTRS1988

A micromechanics model of the stiffness and strength of laminates with fiber waviness

A mathematical model based on the Euler-Bernoulli beam theory is proposed for predicting the effective Young's moduli of piecewise isotropic composite laminates with local ply curvatures in the main load-carrying layers. Strains in corrugated layers, In-Phase layers, Out-of-Phase layers are predicted for various geometries and material configurations by assuming matrix layers as elastic foundations of different spring constants. The effective Young's moduli measured from corrugated aluminum specimens and aluminum/epoxy specimens with In-Phase and Out-of-Phase wavy patterns coincide very well with the model predictions. Moire fringe analysis of an In-Phase specimen and an Out-of-Phase specimen are also presented confirming the main assumption of the model related to the elastic constraint due to the matrix layers. The present model is also compared with the experimental results and other models, including the micro-buckling models, published in the literature. The results of the present study show that even a very small scale local ply curvature produces a noticeable effect on the mechanical constitutive behavior of a laminated composite.

Harris, Charles E.↗
NASA NTRS1990

A deformation-formulated micromechanics model of the effective Young's modulus and strength of laminated composites containing local ply curvature

A mathematical model based on the Euler-Bermoulli beam theory is proposed for predicting the effective Young's moduli of piecewise isotropic composite laminates with local ply curvatures in the main load-carrying layers. Strains in corrugated layers, in-phase layers, and out-of-phase layers are predicted for various geometries and material configurations by assuming matrix layers as elastic foundations of different spring constants. The effective Young's moduli measured from corrugated aluminum specimens and aluminum/epoxy specimens with in-phase and out-of-phase wavy patterns coincide very well with the model predictions. Moire fringe analysis of an in-phase specimen and an out-of-phase specimen are also presented, confirming the main assumption of the model related to the elastic constraint due to the matrix layers. The present model is also compared with the experimental results and other models, including the microbuckling models, published in the literature. The results of the present study show that even a very small-scale local ply curvature produces a noticeable effect on the mechanical constitutive behavior of a laminated composite.

Lee, Jong-Won↗
NASA NTRS1985

Electronic heterodyne readout of fringes in moire deflectometry

An electronic heterodyne technique is described for the readout of fringes in moire deflectometry. The technique is based on phase measurements of signals generated by a photodetector observing the light transmitted through a traveling moire fringe pattern. The phase of the signal is proportional to the fringe deviation and thus to the deflection angle of the light ray. The phase is measured on line by a standard phase meter with an accuracy of 1 deg or 1:360 of a fringe. The technique, which is precise and sensitive, is demonstrated by detecting and measuring a fringe shift of 0.15 mm corresponding to 0.029 of a fringe.

Stricker, J.↗