Search NASA⌕ Search

SEARCH · Search NASA

Results for “Plasma discharges”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Demonstration of Separation Delay with Glow-Discharge Plasma Actuators

Active flow control of boundary-layer separation using glow-discharge plasma actuators is studied experimentally. Separation is induced on a flat plate installed in a closed-circuit wind tunnel by a shaped insert on the opposite wall. The flow conditions represent flow over the suction surface of a modern low-pressure-turbine airfoil. The Reynolds number, based on wetted plate length and nominal exit velocity, is varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low (0.2 percent) and high (2.5 percent) free-stream turbulence intensities are set using passive grids. A spanwise-oriented phased-plasma-array actuator, fabricated on a printed circuit board, is surface-flush-mounted upstream of the separation point and can provide forcing in a wide frequency range. Static surface pressure measurements and hot-wire anemometry of the base and controlled flows are performed and indicate that the glow-discharge plasma actuator is an effective device for separation control.

Hultgren, Lennart S.↗
NASA NTRS1983

A second kind of Beam-Plasma Discharge (BPD): Rocket and laboratory results

It is shown that there are two types of beam plasma discharge observed in rocket shots. The second BPD transition (BPD2) is characterized by a very broad featureless emission extending from much less than the cyclotron frequency to several times the plasma frequency. The characteristic spectra observed close to the beam plasma discharge region are deformed by the intervening plasma when observations are made at a distance from the injection field line and lead to spectra which must be interpreted with care. In one case, the Bernstein mode at 2 fce seems to be a remnant of the broad, featureless spectrum of BPD2.

Kellogg, P. J.↗
NASA NTRS1982

Suprathermal electrons produced by beam-plasma-discharge

Experiments conducted with a low energy plasma lens, HARP, in the electron beam of the large vacuum chamber at Johnson Space Center indicate that an enhanced population of 50 to 300 volt electrons appear when the beam goes into the Beam-Plasma Discharge (BPD) mode. Below the BPD instability the electron distribution appears to be characterized as non-energized single particle scattering and energy loss. At 100 cm from the beam core in the BPD mode the fluxes parallel to the beam are reduced by a factor of 20 with respect to the fluxes at 25 cm. Some evidence for isotropy near the beam core is presented.

Sharp, W. E.↗
NASA NTRS1984

Measurements of the optical emission produced during the laboratory beam plasma discharge

Optical observations of a beam-plasma discharge (BPD) in the laboratory showed that the discharge remained confined to a diameter little more than double that of the beam for injection parallel to the magnetic field and approximately equal to that of the beam for injection at large pitch angles. The diameter was independent of beam current but varied linearly with beam velocity and inversely with magnetic field strength. The ionization rate inferred from the total emission of 3914 A, integrated over the radial extent of the beam, was proportional to the excess beam current above that requied for BPD ignition. The proportionality constant ( 12 + or - 2) x 10 to the 14th ions/cm s A was valid over a wide range of pressure and of magnetic field strength. Power loss to ionization in a 20 m path was estimated at up to 4 percent of the beam power. Evidence is presented for effective confinement of suprathermal electrons (parallel to B) by some unidentified process other than electrostatic confinement.

Hallinan, T. J.↗
NASA NTRS1987

Effects of space plasma discharge on the performance of large antenna structures in low Earth orbit

The anomalous plasma around spacecrafts in low Earth orbit represents the coma of an artificial comet. The plasma discharge is caused by an energetic disturbance of charged particles which were formerly in a state of equilibrium. The plasma can effect the passive and active radio frequency operation of large space antennas by inducing corona discharge or strong arcing in the antenna feeds. One such large space antenna is the 15-meter hoop column antenna which consists of a mesh membrane material (tricot knitted gold plated wire) reflector and carbon fiber tension cords. The atomic oxygen in the plasma discharge state can force the wire base metal particles through the gold lattice and oxydize the metal particles to build a Schottky-barrier contact at the point where the wires meet. This effect can cause strong deviations in the reflector performance in terms of antenna pattern and losses. Also, the carbon-fiber cords can experience a strength reduction of 30 percent over a 40-hour exposure time.

Blume, Hans-Juergen C.↗
NASA NTRS1982

Electron energy distribution produced by beam-plasma discharge

In an investigation of a beam-plasma discharge (BPD), the electron energy distribution of an electron beam moving through a partially ionized gas is analyzed. Among other results, it is found that the occurrence of BPD heats the initially cold electron beam from the accelerator. The directional intensity of electrons measured outside the beam core indicates that most particles suffer a single scattering in energy and pitch angle. At low currents this result is expected as beam particles collide with the neutral atmosphere, while in BPD the majority of particles is determined to still undergo a single scattering near the original beam core. The extended energy spectra at various beam currents show two rather distinct plasma populations, one centered at the initial beam energy (approximately 1500 eV) and the other at approximately 150 eV.

Anderson, H. R.↗
DOE OSTI2023

Similarity-based scaling networks for capacitive radio frequency discharge plasmas

We demonstrate similarity-based scaling networks for capacitive radio frequency (RF) plasmas, which extensively correlate discharge characteristics under varied conditions, incorporating the transition from original to similarity states. Based on fully kinetic particle-in-cell simulations, similar RF discharges in argon are demonstrated with three external control parameters (gas pressure, gap distance, and driving frequency) simultaneously tuned. A complete set of scaling pathways regarding fundamental discharge parameters is obtained, from which each plasma state finds its neighboring node with only one control parameter tuned. The results from this study provide a promising strategy for plasma multi-parameter mapping, enabling effective cross-comparisons, prediction, and manipulation of RF discharge plasmas.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Observation of Quartz Cathode-Luminescence in a Low Pressure Plasma Discharge

Intense, steady-state cathode-luminescence has been observed from exposure of quartz powder to a low pressure rf-excited argon plasma discharge. The emission spectra (400 to 850 nm) associated with the powder luminescence were documented as a function of bias voltage using a spectrometer. The emission was broad-band, essentially washing out the line spectra features of the argon plasma discharge.

Foster, John E.↗
NASA NTRS1985

Electrostatic wave observation during a space simulation beam-plasma discharge

ELF waves which were observed during beam-plasma discharge in the large vacuum chamber at Johnson Space Center are studied. Phase delays as a function of radius (obtained from cross-correlation measurements of density fluctuations) along with measurements of frequency and plasma potential, density, and temperature have been compared to a zero-order slab model of nonlocal azimuthal drift wave propagation. The inferred wave phase velocity in the plasma frame after Doppler correction is found to be near one half the electron diamagnetic drift velocity. Although the measurements presented do not uniquely define a propagation mode, a model of azimuthal drift wave propagation is found to be consistent with observations.

Walker, D. N.↗
DOE OSTI2024

1D Simulation of Avalanche to Streamer to Spark Transition of Plasma Discharge in Ammonia-Air Combustion

The backward problem of plasma assisted combustion emphasizes evaluating the effect of the evolving thermochemical state on the plasma discharge. This paper investigates the dependence of avalanche to streamer to spark formation dynamics and kinetics on the gas composition and temperature at different points in an ammonia-air premixed laminar flame using a self-consistent multigrid-based 1D plasma solver. Different values of ..alpha.., the coefficient for effective ionization events per unit length, have been reported for electron avalanches in air and stoichiometric NH3-air mixtures. The streamer inception has been shown to obey the Meek's criterion. An exponential reduction in streamer and spark formation time has been observed from plasma simulations at different points in the unburnt, pre-heat zone, reaction zone and the fully burnt regions of the premixed flame. While the enhancement of the reduced electric field with increasing temperature affects effective ionization, there exists a minimum breakdown field for streamer formation, which does not vary proportionally with the changing number density of the gas. The change in the mixture from reactants (NH3, O2, N2) to products of complete combustion of ammonia in air (N2, H2O) has also been shown to affect the streamer and spark formation. Finally, the major pathways during the streamer and spark phases which are responsible for producing important radicals used in combustion of NH3 are also discussed.

ADVANCED PROPULSION SYSTEMS,INORGANIC, ORGANIC, PH↗
NASA NTRS1979

Further laboratory measurements of the beam-plasma discharge

The paper presents laboratory measurements of the beam-plasma discharge (BPD) produced when an energetic electron beam traverses an initially neutral gas. The results show that the critical beam current is related to energy, magnetic field, and the system length by an empirical relationship at pressures below 2 times 10 to the -5th power torr. This relationship describes the accumulation of ambient plasma density collisionally produced by the beam to a critical value at which ignition occurs. Additional measurements of the narrow-band cyclotron-related waves observed at beam currents below BPD threshold do not clearly establish whether this instability is a precursor to the BPD.

Bernstein, W.↗
NASA NTRS2003

Boundary-Layer Separation Control under Low-Pressure Turbine Airfoil Conditions using Glow-Discharge Plasma Actuators

Modem low-pressure turbines, in general, utilize highly loaded airfoils in an effort to improve efficiency and to lower the number of airfoils needed. Typically, the airfoil boundary layers are turbulent and fully attached at takeoff conditions, whereas a substantial fraction of the boundary layers on the airfoils may be transitional at cruise conditions due to the change of density with altitude. The strong adverse pressure gradients on the suction side of these airfoils can lead to boundary-layer separation at the latter low Reynolds number conditions. Large separation bubbles, particularly those which fail to reattach, cause a significant degradation of engine efficiency. A component efficiency drop of the order 2% may occur between takeoff and cruise conditions for large commercial transport engines and could be as large as 7% for smaller engines at higher altitude. An efficient means of of separation elimination/reduction is, therefore, crucial to improved turbine design. Because the large change in the Reynolds number from takeoff to cruise leads to a distinct change in the airfoil flow physics, a separation control strategy intended for cruise conditions will need to be carefully constructed so as to incur minimum impact/penalty at takeoff. A complicating factor, but also a potential advantage in the quest for an efficient strategy, is the intricate interplay between separation and transition for the situation at hand. Volino gives a comprehensive discussion of several recent studies on transition and separation under low-pressure-turbine conditions, among them one in the present facility. Transition may begin before or after separation, depending on the Reynolds number and other flow conditions. If the transition occurs early in the boundary layer then separation may be reduced or completely eliminated. Transition in the shear layer of a separation bubble can lead to rapid reattachment. This suggests using control mechanisms to trigger and enhance early transition. Gad-el-Hak provides a review of various techniques for flow control in general and Volino discusses recent studies on separation control under low-pressure-turbine conditions utilizing passive as well as active devices. As pointed out by Volino, passive devices optimized for separation control at low Reynolds numbers tend to increase losses at high Reynolds numbers, Active devices have the attractive feature that they can be utilized only in operational regimes where they are needed and when turned off would not affect the flow. The focus in the present paper is an experimental Separation is induced on a flat plate installed in a closed-circuit wind tunnel by a shaped insert on the opposite wall. The flow conditions represent flow over the suction surface of a modem low-pressure-turbine airfoil ('Pak-B'). The Reynolds number, based on wetted plate length and nominal exit velocity, is varied from 50,000 to 300,000, covering cruise to takeoff conditions. Low (0.2%) and high (2.5%) Gee-stream turbulence intensities are set using passive grids. A spanwise-oriented phased-plasma-array actuator, fabricated on a printed circuit board, is surface- flush-mounted upstream of the separation point and can provide forcing in a wide frequency range. Static surface pressure measurements and hot-wire anemometry of the base and controlled flows are performed and indicate that the glow-discharge plasma actuator is an effective device for separation control. of active separation control using glow discharge plasma actuators.

Hultgren, Lennart S.↗
NASA NTRS1988

Magnetic tearing of plasma discharges due to nonuniform resistivity

The rearrangement of current in a plasma discharge in response to resistivity nonuniformities within a magnetic surface is studied. It is shown that macroscopic magnetic islands develop about those surfaces where the nonuniformity is aligned with the magnetic field. If the nonuniformity and the field are not aligned anywhere, there is no current rearrangement; instead, relatively large plasma flows are set up. Such resistivity inhomogeneities can obtain in solar coronal loops and, in some circumstances, in tokamak discharges.

Hassam, A. B.↗
NASA NTRS1998

Characterization of Plasma Discharges in a High-Field Magnetic Tandem Mirror

High density magnetized plasma discharges in open-ended geometries, like Tandem Mirrors, have a variety of space applications. Chief among them is the production of variable Specific Impulse (I(sub sp)) and variable thrust in a magnetic nozzle. Our research group is pursuing the experimental characterization of such discharges in our high-field facility located at the Advanced Space Propulsion Laboratory (ASPL). These studies focus on identifying plasma stability criteria as functions of density, temperature and magnetic field strength. Plasma heating is accomplished by both Electron and Ion Cyclotron Resonance (ECR and ICR) at frequencies of 2-3 Ghz and 1-30 Mhz respectively, for both Hydrogen and Helium. Electron density and temperature has measured by movable Langmuir probes. Macroscopic plasma stability is being investigated in ongoing research.

Chang-Diaz, Franklin R.↗
NASA NTRS1993

Optical observations of the beam-plasma discharge phenomenon

Spectroscopic observations of optical emissions from the beam-plasma discharge (BPD) phenomenon were made with NASA's vacuum chamber facility, at the Johnson Space Center, configured to simulate the physical conditions of magnetospheric electron beam injection into the ionospheric/upper-atmospheric environment. Nonlinear N2 and N2(+) optical emission growth rates (with respect to incremental electron beam current values) were observed from the chamber gas during transition to the BPD state. For electron-beam currents (I) near the BPD transition value (I(sub c)), the band emissions from the chamber gas produced by relatively low energy (less than or equal to 50 eV) electrons interacting with N2 were anomalously more intense than those requiring higher energy (greater than 100 eV) electrons to excite them. For I more greater than I(sub c), the optical emissions increased linearly with I (as was the case for I less than I(sub c)) and their ratios decreased significantly from the peak values attained when I approximately equals I(sub c). These observations suggest that during BPD some of the energy of the primary electron beam is efficiently transferred, via wave-particle interactions, to local electrons produced through ionization of the chamber gas; the resulting suprathermal electrons provide an additional source of excitation for the relatively low energy states (A, B and C) of N2. Such nonlinear excitation of upper atmospheric gas may occur in certain auroral events wherein the current due to the precipitating electrons approaches a value close to I(sub c).

Sivjee, G. G.↗
DOE OSTI2026

Mathematical Models and Numerical Methods for High-Fidelity Simulation of Ignition of Reactive Mixtures by Nanosecond Plasma Discharges in Realistic Configurations

We present a newly developed framework for the numerical simulation of ignition of reactive mixtures using single or repeated nanosecond discharge pulses. The framework builds upon the AMReX library, using the existing compressible solver PeleC and low-Mach solver PeleLMeX and allowing for adaptive mesh refinement, complex geometries, and execution on next-generation high-performance computing (HPC) systems. High-fidelity elementary models are adopted for weakly-ionised plasma discharges with significant energy deposition, consistent with nanosecond discharge pulses, and then implemented in the solver. The treatment of non-thermal electrons and charged species, thermodynamics of non-equilbrium species, plasma kinetics, limiting time scales, and boundary conditions for charged species are discussed and addressed for computational efficiency. The framework is demonstrated for three relevant applications: single and multi-pulse discharges in air, single pulse ignition of an ethylene/air mixture, and a three-dimensional plasma discharge in air with temperature stratification. The successful application of the framework demonstrates the feasibility of high-fidelity simulation of ignition of air/hydrocarbon mixtures in three-dimensions with multiple discharge pulses.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1988

Spectral signature of the beam plasma discharge

The effect of the beam current on the spectrum of a beam plasma discharge (BPD) in N2 at 50, 100, or 400 microtorr is investigated experimentally in the 2.6-m chamber described by Bernstein et al. (1983). The results are presented graphically and discussed in detail. An increase in the ratio of first positive N2 emissions to first negative N2(+) emissions at BPD onset is shown to disappear at currents above the BPD threshold and is attributed to a large population of suprathermal electrons.

Hallinan, T. J.↗
DOE OSTI2022

Modeling of the effects of non-equilibrium excitation and electrode geometry on H 2 /air ignition in a nanosecond plasma discharge

In this work, we present the results of two-dimensional modeling of the effects of non-equilibrium excitation and electrode geometry on H 2 /air ignition in a nanosecond plasma discharge. A multiscale adaptive reduced chemistry solver for plasma assisted combustion (MARCS-PAC) based on PASSKEy discharge modeling package and compressible multi-component reactive flow solver ASURF+ is developed and validated. This model is applied to simulate the impact of non-equilibrium plasma excitation and electrode geometry and heat loss on the dynamics of the discharge from streamer to spark and ignition kernel development in a H 2 /air mixture with a pair of cylindrical electrodes. The results show that the plasmagenerated species (N 2 (A), N 2 (B), N 2 (a'), N 2 (C), O( 1 D), O and H) in the spark and afterglow significantly accelerate the ignition kernel development. The increase of discharge voltage at the same total discharge energy promotes the non-equilibrium active species production. It is found that the production of electronically excited species at higher reduced electric field strength is more efficient in enhancing ignition in comparison to the vibrational excitation and heating. Moreover, the 2D simulation clearly reveals that the electric field and active species distribution are highly non-uniform. The streamers are initiated at the sharp outer edges of the negative and positive electrodes by a strong electric field while the electric field is much weaker at the centerline of the electrodes. Furthermore, the simulations reveal that the ignition enhancement is sensitive to the variation of electrode shape, diameter, and gap size due to the changes of electric field distribution and location of streamer formation. A cylindrical electrode produces a larger discharge volume and ignition kernel than the parabolic and spherical electrodes, when the discharge is localized near the axis of the gap. It is found that there is a non-monotonic dependence of ignition kernel size on the electrode diameter and inter-electrode distance. The increase of electrode diameter and gap size above the optimal conditions leads to the reduction of ignition kernel volume, due to the decrease of active species concentration and gas temperature. At a larger electrode surface area and electrode diameter as well as smaller electrode gap size, the heat loss to electrode plays a greater role in reducing the ignition kernel size and slowing ignition kernel development. This work provides insights and guidance to understand the kinetic enhancement of non-equilibrium plasma and the effects of electrode geometries on ignition for the optimization ignitors in advanced engines.

42 ENGINEERING↗