Results for “Pu-238” — Page 2

NASA NTRS2015

Modular Stirling Radioisotope Generator

High efficiency radioisotope power generators will play an important role in future NASA space exploration missions. Stirling Radioisotope Generators (SRG) have been identified as a candidate generator technology capable of providing mission designers with an efficient, high specific power electrical generator. SRGs high conversion efficiency has the potential to extend the limited Pu-238 supply when compared with current Radioisotope Thermoelectric Generators (RTG). Due to budgetary constraints, the Advanced Stirling Radioisotope Generator (ASRG) was canceled in the fall of 2013. Over the past year a joint study by NASA and DOE called the Nuclear Power Assessment Study (NPAS) recommended that Stirling technologies continue to be explored. During the mission studies of the NPAS, spare SRGs were sometimes required to meet mission power system reliability requirements. This led to an additional mass penalty and increased isotope consumption levied on certain SRG-based missions. In an attempt to remove the spare power system, a new generator architecture is considered which could increase the reliability of a Stirling generator and provide a more fault-tolerant power system. This new generator called the Modular Stirling Radioisotope Generator (MSRG) employs multiple parallel Stirling convertor/controller strings, all of which share the heat from the General Purpose Heat Source (GPHS) modules. For this design, generators utilizing one to eight GPHS modules were analyzed, which provide about 50 to 450 watts DC to the spacecraft, respectively. Four Stirling convertors are arranged around each GPHS module resulting in from 4 to 32 Stirling/controller strings. The convertors are balanced either individually or in pairs, and are radiatively coupled to the GPHS modules. Heat is rejected through the housing/radiator which is similar in construction to the ASRG. Mass and power analysis for these systems indicate that specific power may be slightly lower than the ASRG and similar to the MMRTG. However, the reliability should be significantly increased compared to ASRG.

Stirling Cycle↗

NASA NTRS2016

Modular Stirling Radioisotope Generator

High-efficiency radioisotope power generators will play an important role in future NASA space exploration missions. Stirling Radioisotope Generators (SRGs) have been identified as a candidate generator technology capable of providing mission designers with an efficient, high-specific-power electrical generator. SRGs high conversion efficiency has the potential to extend the limited Pu-238 supply when compared with current Radioisotope Thermoelectric Generators (RTGs). Due to budgetary constraints, the Advanced Stirling Radioisotope Generator (ASRG) was canceled in the fall of 2013. Over the past year a joint study by NASA and the Department of Energy (DOE) called the Nuclear Power Assessment Study (NPAS) recommended that Stirling technologies continue to be explored. During the mission studies of the NPAS, spare SRGs were sometimes required to meet mission power system reliability requirements. This led to an additional mass penalty and increased isotope consumption levied on certain SRG-based missions. In an attempt to remove the spare power system, a new generator architecture is considered, which could increase the reliability of a Stirling generator and provide a more fault-tolerant power system. This new generator called the Modular Stirling Radioisotope Generator (MSRG) employs multiple parallel Stirling convertor/controller strings, all of which share the heat from the General Purpose Heat Source (GPHS) modules. For this design, generators utilizing one to eight GPHS modules were analyzed, which provided about 50 to 450 W of direct current (DC) to the spacecraft, respectively. Four Stirling convertors are arranged around each GPHS module resulting in from 4 to 32 Stirling/controller strings. The convertors are balanced either individually or in pairs, and are radiatively coupled to the GPHS modules. Heat is rejected through the housing/radiator, which is similar in construction to the ASRG. Mass and power analysis for these systems indicate that specific power may be slightly lower than the ASRG and similar to the Multi-Mission Radioisotope Thermoelectric Generator (MMRTG). However, the reliability should be significantly increased compared to ASRG.

Modules↗

NASA NTRS2017

Milli-Watt Radioisotope Power to Enable Small, Long-Term Robotic “Probe” Space Exploration

Milli-watt Radioisotope Power Systems (RPS) based on Radioisotope Heater Units (RHUs) could be an ideal power source for certain spacecraft that cannot use solar power due to large distances from the sun, or other environmental constraints, and where they enable or significantly enhance the ability of a mission to meet its scientific or operational goals. Various modular, compact RHU-based thermoelectric (TE) generator concepts developed or derived from current NASA Small Business Innovation Research (SBIR) projects satisfying this need have been investigated. These modular, compact and low mass power systems could support small, highly-mobile robotic exploration packages, and could be incorporated into different robotic package concepts, spacecraft or satellites. Current modular RPS design concepts with 40mW, 80mW and 120mW power levels use RHUs and Bi2Te3 TE converters. Skutterudites materials could be used in the future if new higher thermal energy output and higher temperature miniature heat sources were developed, for example, using technologies currently in the General Purpose Heat Source (GPHS) used in higher electric power output RTGs. Small (a.k.a., “mice-like”) robotic packages could effectively utilize these RHU-driven power levels to accommodate crawling, climbing, monitoring, taking measurements, and communicating during long-term planetary missions aimed at gathering environmental and geologic data (i.e., over multiple decades). Waste heat from the cold side of the TE converter could also be directed toward the electronics and / or energy storage (e.g. batteries) to keep them within design temperature ranges. In addition to power generation and electronics / battery heating, the RHU / TE configuration could be designed to survive an external 500°C bake out procedure for critical spacecraft sterilization, environmental certification and planetary protection. Analytical studies have been performed to optimize various design configurations for power, mass, volume and robotic mobility. Specific power (mW/kg) and volumetric specific power (mW/cm3) characteristics of various design configurations will be presented and key conceptual design tradeoffs will be discussed. Hot- and cold-side thermal interfaces required to meet power and mass goals and associated design sensitivities will also be discussed. RHU / TE systems must overcome critical design challenges to survive high-g loadings in some robotic applications and we will examine the mass impacts required to satisfy various dynamic loading environments up to 10,000 g’s. Power can be generated for a minimum of 30 years or more using plutonium-238 dioxide heat sources (given that Pu-238 has an 87.7 year half-life) with some reduction in power as the heat source naturally degrades.

Bahrami, Poyan↗

NASA NTRSDate not supplied

Dynamic Radioisotope Power Systems Development Status and Path to Flight

Dynamic power conversion offers the potential to produce Radioisotope Power Systems (RPS) that generate higher power outputs and utilize the Pu-238 radioisotope more efficiently. Additionally, dynamic power conversion offers the potential of producing generators with minimal degradation resulting in more power at the end of the mission, when the power is needed. Dynamic power conversion technologies being developed for space applications include the Stirling and Brayton thermodynamic cycle machines. Machines can be built based on these cycles while eliminating wear mechanisms of the moving components, enabling long design life necessary for space missions. The Dynamic Radioisotope Power Systems (DRPS) project at NASA Glenn Research Center (Glenn Research Center) is pursuing the realization of this type of power source on a flight mission. The project currently has three convertor development contracts that will deliver prototype hardware in 2020. This hardware will undergo a gamut of experimental performance verification efforts at NASA GRC. In parallel, the project has also initiated generator design efforts based on these underlying convertor options, and is also on track to build an in-house version of a generator for laboratory system-level testing. The project is also funding control electronics technology, which are necessary to convert alternating current from the dynamic devices to direct current for use by a spacecraft. A lunar mission is being targeted as the first use of this new technology, as DRPS enables a wide range of high-return scientific missions on the moon, while the mission being short in duration (2 years rather than 10 years for an outer planets mission).

Salvatore M Oriti↗

NASA NTRSDate not supplied

Dynamic Radioisotope Power Systems Status and Path to Flight

Dynamic power conversion offers the potential to produce Radioisotope Power Systems (RPS) that generate higher power outputs and utilize the Pu-238 radioisotope more efficiently. Additionally, dynamic power conversion offers the potential of producing generators with minimal degradation resulting in more power at the end of the mission, when the power is needed. Dynamic power conversion technologies being developed for space applications include the Stirling and Brayton thermodynamic cycle machines. Machines can be built based on these cycles while eliminating wear mechanisms of the moving components, enabling long design life necessary for space missions. The Dynamic Radioisotope Power Systems (DRPS) project at NASA Glenn Research Center (Glenn Research Center) is pursuing the realization of this type of power source on a flight mission. The project currently has three convertor development contracts that will deliver prototype hardware in 2020. This hardware will undergo a gamut of experimental performance verification efforts at NASA GRC. In parallel, the project has also initiated generator design efforts based on these underlying convertor options, and is also on track to build an in-house version of a generator for laboratory system-level testing. The project is also funding control electronics technology, which are necessary to convert alternating current from the dynamic devices to direct current for use by a spacecraft. A lunar mission is being targeted as the first use of this new technology, as DRPS enables a wide range of high-return scientific missions on the moon, while the mission being short in duration (2 years rather than 10 years for an outer planets mission).

Salvatore Oriti↗