Search NASA⌕ Search

SEARCH · Search NASA

Results for “Quenching limits”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

MO-F-CAMPUS-T-03: Verification of Range, SOBP Width, and Output for Passive-Scattering Proton Beams Using a Liquid Scintillator Detector

Purpose: Liquid scintillators have been shown to provide fast and high-resolution measurements of radiation beams. However, their linear energy transfer-dependent response (quenching) limits their use in proton beams. The purpose of this study was to develop a simple and fast method to verify the range, spread-out Bragg peak (SOBP) width, and output of a passive-scattering proton beam with a liquid scintillator detector, without the need for quenching correction. Methods: The light signal from a 20×20×20 cm3 liquid scintillator tank was collected with a CCD camera. Reproducible landmarks on the SOBP depth-light curve were identified which possessed a linear relationship with the beam range and SOBP width. The depth-light profiles for three beam energies (140, 160 and 180 MeV) with six SOBP widths at each energy were measured with the detector. Beam range and SOBP width calibration factors were obtained by comparing the depth-light curve landmarks with the nominal range and SOBP width for each beam setting. The daily output stability of the liquid scintillator detector was also studied by making eight repeated output measurements in a cobalt-60 beam over the course of two weeks. Results: The mean difference between the measured and nominal beam ranges was 0.6 mm (σ=0.2 mm), with a maximum difference of 0.9 mm. The mean difference between the measured and nominal SOBP widths was 0.1 mm (σ=1.8 mm), with a maximum difference of 4.0 mm. Finally an output variation of 0.14% was observed for 8 measurements performed over 2 weeks. Conclusion: A method has been developed to determine the range and SOBP width of a passive-scattering proton beam in a liquid scintillator without the need for quenching correction. In addition to providing rapid and accurate beam range and SOBP measurements, the detector is capable of measuring the output consistency with a high degree of precision. This project was supported in part by award number CA182450 from the National Cancer Institute.

07 ISOTOPE AND RADIATION SOURCES↗

Development of Magnesium Diboride Superconducting Coils for Nuclear Physics Application

The primary objective of this project is to develop an affordable magnet technology at 10-25K and then take it to a level that it can be considered mature enough to be used in a real Nuclear Physics accelerator system. We believe that because of the lower cost of magnesium diboride (MgB2) as compared to the other HTS, it offers the best such chance. Once successfully demonstrated, this exciting and innovative technology could potentially revolutionize the field the same way the conventional superconducting NbTi magnets did several decades ago. MgB2 magnets could reduce the cost of ownership (capital +operation) while enhancing performance. Another innovation is the overall cooling scheme where the exhaust gas of an existing superconducting magnet cools the inner tube which conduction cools the MgB2 coils. In several instances during the upgrade of existing facilities or designing new facilities in the Nuclear Physics or High Energy Physics communities, it is found that magnets made neither with copper coils nor with conventional superconducting NbTi coils offer an acceptable solution. Whereas copper coils limit the performance of the machine and consume large amount of power, NbTi require 4 K cryogenic facilities. This is particularly applicable in those Nuclear Physics machines where the magnetic field requirements are rather modest. One such case has been found in the Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Laboratory (BNL) where an e-lens system is under construction to increase RHIC luminosity. In this case, magnesium diboride (MgB2) operating at 10-25 K seems to offer an exciting and practical solution. The main objective in Phase II is to demonstrate the reliability and robustness of the MgB2 coil technology, so that it is ready for use in RHIC and other user facilities. We will do this by fabricating several MgB2 coils and by conducting an exhaustive series of lifetime cycle tests. The tests will involve about a thousand ramp-up and ramp-down cycles, about 20 over current or thermal-excursions hitting the quench limit and about 10 thermal cycles. Phase II will begin with a design modeling effort of the MgB2 coils for the e-lens system with enough detail so that the magnetic, thermal and stress requirements can be understood for the fabrication and testing of representative MgB2 coils. After the technology is proven in Phase II for reliability, we will propose to use this in Phase III to upgrade RHIC e-lens system for improved luminosity performance and expect that more applications will follow in other accelerator and medical facilities.

99 GENERAL AND MISCELLANEOUS↗

Preliminary Cryogenic Cold Test Results of the First 9-Cell LSF Shape Cavity

Following successful prototyping and testing of single- & 5-cell LSF shape cavities *, **, the first 9-cell LSF shape cavity LSF9-1 was successfully constructed using an innovative process at JLab with the in-house facilities. The cavity was then shipped to KEK for post-fabrication mechanical adjustment and ILC TDR style treatment and surface processing. Cold testing was carried out at the JLab VTA facility, instrumented with a suite of Kyoto instruments. Favorable values for the bath pressure detuning sensitivity and Lorentz force detuning coefficient were experimentally measured, validating the design improvement in cell stiffeners. Pass-band measurements indicate 4 out of 9 cells reaching gradient capability of > 45 MV/m, including 2 cells reaching 51 MV/m. Cornell OST detectors identified the cell and location responsible for the current hard quench limit. Multipacting-like barriers observed in end cells are investigated both analytically and numerically. The cavity was shipped to FNAL and received a light EP at the joint ANL/FNAL facility for further cold testing at Jlab. Two new 9-cell LSF cavities are being constructed including one made of large-grain niobium material.

43 PARTICLE ACCELERATORS↗

In Silico Design of DNP Polarizing Agents: Can Current Dinitroxides Be Improved?

Numerical calculations of enhancement factors offered by dynamic nuclear polarization in solids under magic angle spinning (DNP-MAS) were performed to determine the optimal EPR parameters for a dinitroxide polarizing agent. We found that the DNP performance of a biradical is more tolerant to the relative orientation of the two nitroxide moieties than previously thought. In general, any condition in which the gyy tensor components of both radicals are perpendicular to one another is expected to have near-optimal DNP performance. These results highlight the important role of the exchange coupling, which can lessen the sensitivity of DNP performance to the inter-radical distance, but also lead to lower enhancements when the number of atoms in the linker becomes less than three. Finally, the calculations showed that the electron T1e value should be near 500μs to yield optimal performance. Importantly, the newest polarizing agents already feature all of the qualities of the optimal polarizing agent, leaving little room for further improvement. Further research into DNP polarizing agents should then target non-nitroxide radicals, as well as improvements in sample formulations to advance high-temperature DNP and limit quenching and reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Deep Quench Approach to the Optimal Control of an Allen–Cahn Equation with Dynamic Boundary Conditions and Double Obstacles

In this paper, we investigate optimal control problems for Allen-Cahn variational inequalities with a dynamic boundary condition involving double obstacle potentials and the Laplace-Beltrami operator. The approach covers both the cases of distributed controls and of boundary controls. The cost functional is of standard tracking type, and box constraints for the controls are prescribed. We prove existence of optimal controls and derive first-order necessary conditions of optimality. The general strategy is the following: we use the results that were recently established by two of the authors for the case of (differentiable) logarithmic potentials and perform a so-called “deep quench limit”. Using compactness and monotonicity arguments, it is shown that this strategy leads to the desired first-order necessary optimality conditions for the case of (non-differentiable) double obstacle potentials.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Detonation mode and frequency analysis under high loss conditions for stoichiometric propane-oxygen

In this paper, the propagation characteristics of galloping detonations were quantified with a high-time-resolution velocity diagnostic. Combustion waves were initiated in 30-m lengths of 4.1-mm inner diameter transparent tubing filled with stoichiometric propane–oxygen mixtures. Chemiluminescence from the resulting waves was imaged to determine the luminous wave front position and velocity every 83.3 μ. As the mixture initial pressure was decreased from 20 to 7 kPa, the wave was observed to become increasingly unsteady and transition from steady detonation to a galloping detonation. While wave velocities averaged over the full tube length smoothly decreased with initial pressure down to half of the Chapman–Jouguet detonation velocity (D CJ ) at the quenching limit, the actual propagation mechanism was seen to be a galloping wave with a cycle period of approximately 1.0 ms, corresponding to a cycle length of 1.3–2.0 m or 317–488 tube diameters depending on the average wave speed. The long test section length of 7300 tube diameters allowed observation of up to 20 galloping cycles, allowing for statistical analysis of the wave dynamics. In the galloping regime, a bimodal velocity distribution was observed with peaks centered near 0.4 D CJ and 0.95 D CJ . Decreasing initial pressure increasingly favored the low velocity mode. Galloping frequencies ranged from 0.8 to 1.0 kHz and were insensitive to initial mixture pressure. Wave deflagration-to-detonation transition and detonation failure trajectories were found to be repeatable in a given test and also across different initial mixture pressures. The temporal duration of wave dwell at the low and high velocity modes during galloping was also quantified. It was found that the mean wave dwell duration in the low velocity mode was a weak function of initial mixture pressure, while the mean dwell time in the high velocity mode depended exponentially on initial mixture pressure. Analysis of the velocity histories using dynamical systems ideas demonstrated trajectories that varied from stable to limit cycles to aperiodic motion with decreasing initial pressure. Finally, the results indicate that galloping detonation is a persistent phenomenon at long tube lengths.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-efficiency cross-beam magnetic electron-impact source for improved miniature Mattauch-Herzog mass spectrometer performance

We describe a newly designed cross-beam magnetic electron-impact ion source (CBM-EI). We demonstrate its superiority in comparison with a conventional source (CB-EI) when used with a commercial miniature sector-field-type, non-scanning mass spectrometer featuring Mattauch-Herzog geometry (MH-MS) and a permanent sector-field magnet. This paper clearly shows the value of the CBM-EI for enhancing MH-MS sensitivity. Unlike secondary electron-multiplier type detectors, the pixelated detector (IonCCD Trade-Mark-Sign ) used in the commercial MH-MS has no gain. The MH-MS/IonCCD system is therefore challenged to compete with time-of-flight and quadrupole MS systems due to their higher ion transmissions and detector gains. Using the new CBM-EI, we demonstrate an instrument sensitivity increase of 20-fold to 100-fold relative to the CB-EI-equipped instrument. This remarkable signal increase by the simple addition of the magnet assembly arises from the magnet-induced gyromotion of the thermionic electrons, which vastly increases the effective path length of the electrons through the ionization region, and the collimated nature of the electron flux, which optimizes the ion transmission through the 100-{mu}m object slit of the MH-MS. Some or all of the realized sensitivity increase may be exchanged for an increase in resolution and/or mass range through the use of a narrower object slit, or for a reduction in ion-source pressure to limit quenching. The CBM-EI should facilitate development of a differentially pumped ion source to extend the lifetime of the filament, especially in otherwise intractable applications associated with oxidizing and corrosive samples.

43 PARTICLE ACCELERATORS↗

Efficient calculation of self magnetic field, self-force, and self-inductance for electromagnetic coils with rectangular cross-section

Abstract For designing high-field electromagnets, the Lorentz force on coils needs to be computed in order to design suitable support structures, and the inductance should be computed to evaluate the stored energy and dynamics. Also, the magnetic field and its variation inside the conductor is of interest for computing stress and strain, and due to superconducting quench limits. For these force, inductance, energy, and internal field calculations, the coils cannot be naively approximated as infinitesimally thin filaments due to divergences when the source and evaluation points coincide, so more computationally demanding calculations are usually required, resolving the finite cross-section of the conductors. Here, we present a new alternative method that enables the internal magnetic field vector, self-force, and self-inductance to be computed rapidly and accurately within a 1D filament model. The method is applicable to coils for which the curve center-line can have general noncircular shape, as long as the conductor width is small compared to the radius of curvature. This paper extends a previous calculation for circular-cross-section conductors (Hurwitz et al 2024 IEEE Trans. Magn. ) to consider the case of rectangular cross-section. The reduced model is derived by rigorous analysis of the singularity, regularizing the filament integrals such that they match the true high-dimensional integrals at high coil aspect ratio. The new filament model exactly recovers analytic results for a circular coil, and is shown to accurately reproduce full finite-cross-section calculations for a non-planar coil of a stellarator magnetic fusion device. Due to the efficiency of the model here, it is well suited for use inside design optimization.

Landreman, Matt (ORCID:000000027233577X)↗

The Higgs Factory muon collider superconducting magnets and their protection against beam decay radiation

We report a low-energy medium-luminosity Muon Collider (MC) is being studied as a possible Higgs Factory (HF). Electrons from muon decays will deposit more than 300 kW in superconducting (SC) magnets of the HF collider ring. This imposes significant challenges to SC magnets used in the HF storage ring (SR) and interaction regions (IR). Conceptual designs of SC dipole and quadrupole magnets are described which provide high operating gradient and field in a large aperture to accommodate the large size of muon beams (due to low β*), as well as a cooling system to intercept the large heat deposition from the showers induced by decay electrons. The distribution of heat deposition in the main elements of HF SR lattice requires large-aperture magnets to accommodate thick high-Z absorbers to protect the SC coils. Based on the developed MARS15 model and intensive simulations, a sophisticated protection system from radiation was designed for the collider SR and IR to bring the peak power density in the SC coils well below the quench limit and reduce the dynamic heat deposition in the cold mass of SC magnets by a factor of 100. The radiation protection system consists of tight tungsten masks in the magnet interconnect regions and elliptical tungsten liners in the magnet aperture optimized for each magnet. Lastly, these elements reduce also the background particle fluxes in the collider detector.

43 PARTICLE ACCELERATORS↗

Coupled-channel and screening effects in charmonium spectrum

Using the same quenched limit as input, we compare the charmonium spectra predicted by two different models, i.e., the coupled-channel model and the screened potential model in the mass region below 4 GeV, in which the contributions from decay channels involving P-wave (as well as even higher excited) D mesons can be neglected. We find that the two models have similar global features in describing the charmonium spectrum since they approximately embody the same effect of the vacuum polarization of dynamical light quark pairs. Adopting these models will be helpful to clarify the nature of the newly discovered charmonium or charmoniumlike states; and the coupled-channel model is more adept in investigating the influences of open-charm thresholds on the charmonium spectrum. In particular, we show the S-wave decay coupling effect on lowering the {chi}{sub c1}(2P) mass toward the DD* threshold, in support of the assignment of the X(3872) as a {chi}{sub c1}(2P)-dominated charmonium state.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

An experimental study of opposed flow diffusion flame extinction over a thin fuel in microgravity

The flame spread and flame extinction characteristics of a thin fuel burning in a low-speed forced convective environment in microgravity were examined. The flame spread rate was observed to decrease both with decreasing ambient oxygen concentration as well as decreasing free stream velocity. A new mode of flame extinction was observed, caused by either of two means: keeping the free stream velocity constant and decreasing the oxygen concentration, or keeping the oxygen concentration constant and decreasing the free stream velocity. This extinction is called quenching extinction. By combining this data together with a previous microgravity quiescent flame study and normal-gravity blowoff extinction data, a flammability map was constructed with molar percentage oxygen and characteristic relative velocity as coordinates. The Damkohler number is not sufficient to predict flame spread and extinction in the near quench limit region.

Ferkul, Paul V.↗

Microgravity combustion of dust suspensions

Unlike the combustion of homogeneous gas mixtures, there are practically no reliable fundamental data (i.e., laminar burning velocity, flammability limits, quenching distance, minimum ignition energy) for the combustion of heterogeneous dust suspensions. Even the equilibrium thermodynamic data such as the constant pressure volume combustion pressure and the constant pressure adiabatic flame temperature are not accurately known for dust mixtures. This is mainly due to the problem of gravity sedimentation. In normal gravity, turbulence, convective flow, electric and acoustic fields are required to maintain a dust in suspension. These external influences have a dominating effect on the combustion processes. Microgravity offers a unique environment where a quiescent dust cloud can in principle be maintained for a sufficiently long duration for almost all combustion experiments (dust suspensions are inherently unstable due to Brownian motion and particle aggregation). Thus, the microgravity duration provided by drop towers, parabolic flights, and the space shuttle, can all be exploited for different kinds of dust combustion experiments. The present paper describes some recent studies on microgravity combustion of dust suspension carried out on the KC-135 and the Caravelle aircraft. The results reported are obtained from three parabolic flight campaigns.

Lee, John H. S.↗

Solid Inflammability Boundary at Low Speed (SIBAL)

This research program is concerned with the effect of low-speed, concurrent flow on the spreading and extinction processes of flames over solid fuels. The primary objective is to verify the theoretically predicted extinction boundary, using oxygen percentage and flow velocity as coordinates. In particular, we are interested in the low-speed quenching limits and the existence of the critical oxygen flammability limit. Detailed flame spread characteristics, including flame spread rate, flame size, and flame structure are sought. Since the predicted flame behavior depends on the inclusion of flame and surface radiation, the measured results will also be used to assess the importance of radiative heat transfer by direct comparison to a comprehensive numerical model. This project passed the Science Concept Review (SCR) in 1996. As a result, the experiment continues on the flight definition path, and is currently scheduled to be performed in the Space Station Combustion Integrated Rack (CIR). We present an overview of recent and ongoing work, including selected experimental and theoretical topics.

T'ien, James S.↗

Solid Inflammability Boundary at Low-Speed (SIBAL)

This research program is concerned with the effect of low-speed, concurrent flow on the spreading and extinction processes of flames over solid fuels. The primary objective is to verify the theoretically predicted extinction boundary, using oxygen percentage and flow velocity as coordinates. Of particular interest are the low-speed quenching limits and the existence of the critical oxygen flammability limit. Detailed flame spread characteristics, including flame spread rate, flame size, and flame structure are sought. Since the predicted flame behavior depends on the inclusion of flame and surface radiation, the measured results will also be used to assess the importance of radiative heat transfer by direct comparison to a comprehensive numerical model. The solid fuel used in this experiment is a custom-made fabric consisting of a 1:1 blend of cotton and fiberglass. This choice was made following an extensive search to yield a material with favorable properties, namely, rollability, non-cracking behavior during combustion, strength after combustion, and flammability in a range of oxygen limits permissible within the Combustion Integrated Rack (CIR) on the International Space Station. At the present time, an effort is being made to characterize both the radiative properties of the fuel and the flame spreading behavior in normal gravity at reduced pressure. These will provide a basis for comparison with the microgravity results as well as aid in bracketing the anticipated flammability boundary for the flight experiment. An overview of recent work, with emphasis on theoretical results, is presented.

T'ien, James↗

Iodine Tagging Velocimetry in a Mach 10 Wake

A variation on molecular tagging velocimetry (MTV) [1] designated iodine tagging velocimetry (ITV) is demonstrated. Molecular iodine is tagged by two-photon absorption using an Argon Fluoride (ArF) excimer laser. A single camera measures fluid displacement using atomic iodine emission at 206 nm. Two examples ofMTVfor cold-flowmeasurements areN2OMTV [2] and Femtosecond Laser Electronic Excitation Tagging [3]. These, like most MTV methods, are designed for atmospheric pressure applications. Neither can be implemented at the low pressures (0.1- 1 Torr) in typical hypersonic wakes. Of all the single-laser/singlecamera MTV approaches, only Nitric-Oxide Planar Laser Induced Fluorescence-based MTV [4] has been successfully demonstrated in a Mach 10 wake. Oxygen quenching limits transit times to 500 ns and accuracy to typically 30%. The present note describes the photophysics of the ITV method. Off-body velocimetry along a line is demonstrated in the aerothermodynamically important and experimentally challenging region of a hypersonic low-pressure near-wake in a Mach 10 air wind tunnel. Transit times up to 10 μs are demonstrated with conservative errors of 10%.

Balla, Robert Jeffrey↗

A Comparison of NO Laser-Induced Fluorescence Models at Conditions Relevant to Supersonic and Hypersonic Flows

Planar laser-induced fluorescence (PLIF) of the nitric oxide (NO) molecule has been widely used in wind tunnel facilities for flow visualization, velocity, and temperature measurements. The experimental PLIF measurements are often compared with synthetic PLIF images using computationally derived temperatures, pressures, velocities, and species mole fractions. This approach is commonly referred to as computational flow imaging (CFI). In the present work, we compare signal intensity from PLIF models with experimental PLIF measurements obtained within a low pressure gas cell system at pressures and NO mole fractions relevant to supersonic and hypersonic flowfields. Experimental measurements were compared to several different laser induced-fluorescence models reported in the literature including LIFBASE, LINUS, and a NASA two-level model. The experimental measurements agreed well with all of the models at lower pressures and lower NO mole fractions; the fluorescence there is linear with both of these parameters. However, at higher pressures and mole fractions, the signal becomes nonlinear with respect to these parameters as self-quenching limits the signal and absorption further limits the signal. In fact, for the experimental path length of the experiment, the combination of high pressure and high NO mole fraction causes the experimental results to deviate significantly from the predicted results that neglect absorption of the incident laser sheet. The LINUS model, which allows absorption to be calculated, provided results that agreed better with the experimental measurements. Since supersonic and hypersonic flowfields may contain a region of the flow with high pressures and measurements in large-scale facilities often include a long path length, neglecting absorption may have a significantly negative effect on the CFI comparison to experimental PLIF images. As a result, PLIF models that account for absorption should be included in computational flow imaging approaches for laser induced fluorescence.

laser-induced fluorescence↗

Improving gradient and Q performance of BCP etched multi-cell cavities by applying a light EP

We have electropolishing (EP) processed several multi-cell cavities previously heavy buffered chemical polishing (BCP) etched. With a surprisingly light EP removal of less than 50 micron, all cavities have shown significant gradient and Q improvement. So far three cavities including two fine-grain niobium 7-cell CEBAF upgrade prototype cavities and one large-grain niobium 9-cell ILC cavities have been treated and tested. The two 7-cell cavities reached a quench limit (without field emission) of 35 MV/m and 25 MV/m, respectively. Another 7-cell cavity has been treated and is under RF test. We give a summary of the test results.

36 MATERIALS SCIENCE↗

THERMAL ANALYSIS OF THE RHIC ARC DIPOLE MAGNET COLD MASS WITH THE EIC BEAM SCREEN

The EIC will make use of the existing RHIC storage rings with their superconducting (SC) magnet arcs. A stain-less-steel beam screen with co-laminated copper and a thin amorphous carbon (aC) film on the inner surface will be installed in the beam pipe of the SC magnets. The copper will reduce the beam-induced resistive-wall (RW) heating from operation with the higher intensity EIC beams, that if not addressed would make the magnets quench. Limiting the RW heating is also important to achieve an adequately low vacuum level. The aC coating will reduce secondary electron yield which could also cause heating and limit in-tensity. Among all the RHIC SC magnets, the arc dipoles present the biggest challenge to the design and installation of beam screens. The arc dipoles, which make up for 78% (2.5 km) length of all SC magnets in RHIC, expect the larg-est RW heating due to their smallest aperture. These mag-nets are also the longest (9.45 m each), thus experiencing the largest temperature rise over their length, and have a large sagitta (48.5 mm) that increases the difficulty to in-stall the beam screen in place. This paper presents a de-tailed thermal analysis of the magnet-screen system.

43 PARTICLE ACCELERATORS↗