SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A hydrophobic electroconductive LIG membrane with ∼143.7° water contact angle is prepared showing average surface temperature of ∼140 °C with 91 MHz radiofrequency heating. Vacuum membrane distillation shows ∼13.5 L m −2 h −1 flux.
Abstract While humid atmospheric pressure plasmas are extensively modeled, reaction set validation for these conditions remains limited. We present a detailed comparison of a modelling and experimental study with a goal to elucidate the plasma chemistry in a humid Ar radiofrequency-driven atmospheric pressure plasma jet. A large group of species including radicals (H, OH, O, HO 2 ) and long-lived species (H 2 , O 2 and H 2 O 2 ) in the jet effluent was experimentally quantified by molecular beam mass spectroscopy (MBMS). MBMS measurements of H 2 O 2 , OH and H were validated by direct comparison with a liquid phase colorimetric measurement, laser-induced fluorescence (LIF) and two-photon absorption LIF respectively. While an excellent agreement was found for OH and H 2 O 2 by both techniques, a significant difference was found for H and shown to be due to boundary layer effects at the MBMS sampling substrate. The measured O, OH, HO 2 and H 2 are in good agreement with the plug model while H and O 2 were underestimated and H 2 O 2 was overestimated by the model. The accuracy of both the used reaction set and the diagnostics, as well as the observed discrepancies between the modeling and experimental results, are critically assessed. The results presented in this work enable us to identify further data needs for describing H 2 O vapor chemistry in low-temperature plasmas.
Abstract We demonstrate practical accelerating gradients on a superconducting radiofrequency (SRF) accelerator cavity with cryocooler conduction cooling, a cooling technique that does not involve the complexities of the conventional liquid helium bath. A design is first presented that enables conduction cooling an elliptical-cell SRF cavity. Implementing this design, a single cell 650 MHz Nb 3 Sn cavity coupled using high purity aluminum thermal links to a 4 K pulse tube cryocooler generated accelerating gradients up to 6.6 MV m −1 at 100% duty cycle. The experiments were carried out with the cavity-cryocooler assembly in a simple vacuum vessel, completely free of circulating liquid cryogens. We anticipate that this cryocooling technique will make the SRF technology accessible to interested accelerator researchers who lack access to full-stack helium cryogenic systems. Furthermore, the technique can lead to SRF based compact sources of high average power electron beams for environmental protection and industrial applications. A concept of such an SRF compact accelerator is presented.
Nb 3 Sn is a promising advanced material under development for superconducting radiofrequency cavities. Past efforts have been focused primarily on small development-scale cavities, but large, often multi-celled cavities, are needed for particle accelerator applications. In this work, we report on successful Nb 3 Sn coatings on Nb in a 1 m-long 9-cell Nb sample-host cavity at Fermilab. The geometry of the first coating with only one Sn source made it possible to study the influence of Sn flux on the microstructure. Based on these results, we postulate a connection between recently observed anomalously large thin grains and uncovered niobium spots observed in the past by other authors (Trenikhina et al 2018 Supercond. Sci. Technol. 32 015004). A phenomenological model to explain how these anomalously large grains could form is proposed. Overall, this model is invoked to provide possible explanations for literature results from several groups and to guide key process parameters to achieve uniform vapor-diffusion coatings, when applied to complex structures as the multi-cell cavity under study.
Radiofrequency sheath rectification is a phenomenon relevant to the operation of Ion Cyclotron Range of Frequencies (ICRFs) actuators in tokamaks. Techniques to model the sheath rectification on 3D ICRF antenna geometries have only recently become available (Shiraiw et al 2023 Nucl. Fusion 63 026024; Beers et al 2021 Phys. Plasmas 28 093503). In this work, we apply the 'sheath-equivalent dielectric layer' technique, used previously only on linear devices (Beers et al 2021 Phys. Plasmas 28 103508), in tokamak geometry, computing rectified sheath potentials on the WEST ICRF antenna. Advancing the state of the art in sheath rectification modeling, we compute the sheath potentials not just on the limiters, but also on the Faraday Screen bars. The calculations show a peak rectified DC potential of 300 V on the limiters and 500 V on the Faraday screen. Assuming a typical sputtering yield curve, the RF sheath rectification increases the sputtering yield from the limiters by a factor of 2.6 w.r.t. the sputtering due to the non-rectified thermal sheath.
In inhomogeneous media, electromagnetic-wave rays deviate from the trajectories predicted by the leading-order geometrical optics. This effect, called the spin Hall effect of light, is typically neglected in ray-tracing codes used for modeling waves in plasmas. Here, we demonstrate that the spin Hall effect can be significant for radiofrequency waves in toroidal magnetized plasmas whose parameters are in the ballpark of those used in fusion experiments. For example, an electron-cyclotron wave beam can deviate by as large as 10 wavelengths (~ 0.1 m) relative to the lowest-order ray trajectory in the poloidal direction. Finally, we calculate this displacement using gauge-invariant ray equations of extended geometrical optics, and we also compare our theoretical predictions with full-wave simulations.
The forming limit diagram (FLD) of high-purity niobium sheets used for the manufacturing of superconducting radiofrequency (SRF) cavities is presented. The Marciniak (in-plane) test was used with niobium blanks with a thickness of 1 mm and blank carriers of annealed oxygen-free electronic (OFE) copper. A high formability was measured, with an approximate true major strain at necking for plane strain of 0.44. The high formability of high-purity niobium is likely caused by its high strain rate sensitivity of 0.112. Plastic strain anisotropies (r-values) of 1.66, 1.00, and 2.30 were measured in the 0 deg, 45 deg, and 90 deg directions. However, stress–strain curves at a nominal strain rate of ~10 –3 s –1 showed similar mechanical properties in the three directions. Theoretical calculations of the forming limit curves (FLCs) were conducted using an analytical two-zone model. The obtained results indicate that the anisotropy and strain rate sensitivity of niobium affect its formability. The model was used to investigate the influence of strain rate on strains at necking. The obtained results suggest that the use of high-speed sheet forming should further increase the formability of niobium.
The occurrence of radiofrequency (RF) breakdown limits operational electromagnetic gradients in accelerator structures. Experimental evidence often suggests that breakdown events are associated with temperature and dark current spikes on the surface of RF devices. In the past decade, there has been increased interest in unveiling the mechanism behind breakdown initiation in metal copper and copper alloys; however, efforts regarding a breakdown phenomenon in photocathode-relevant semiconductors have been more limited. In this work, we explore field-emission-assisted heating via Nottingham and Joule processes, as a possible candidate for breakdown initiation. For this, field emission from an intrinsic Cs2Te ultrathin film coated on a copper substrate was modeled within the Stratton–Baskin–Lvov–Fursey formalism, describing the processes and effects in the bulk and on the surface of a photocathode exposed to high RF electromagnetic fields. It is shown that a field-emission characteristic deviates significantly from the classical Fowler–Nordheim (FN) theory, whereby predicting that dark current is orders of magnitude lower than the one expected by FN law. Conventional pulsed heating was also found to impose negligible heating to the photocathode. Both conclusions suggest that a Cs2Te photocathode coated on a metal substrate would be insensitive to catastrophic thermal-material runaway breakdown, unlike what is observed for metal surfaces. Finally, a few unconventional breakdown candidate scenarios are identified and discussed, including thermoelastic deformation and avalanche breakdown.
Amorphous carbon is an attractive material for next-generation inertial confinement fusion (ICF) ablators due to its amorphous structure, tunable density, compatibility with dopants, chemical inertness, and mechanical robustness. Ablators are typically deposited as ultrathick (10–200 μm) coatings on removable spherical templates. The deposition of such thick amorphous carbon films is challenging due to high intrinsic compressive stress, which causes film buckling and delamination. Here, we study the deposition of amorphous carbon films by magnetized, radiofrequency-driven hollow cathode chemical vapor deposition with a custom-designed source in Ne plasmas. Emphasis is on the hollow-cathode source design and effects of the plasma discharge power and the precursor flow rate on film properties. We demonstrate deposition rates of >1 μm/h for films with hydrogen content of ∼40 at. %, densities of 1.1–1.7 g/cm 3 , and trace quantities of oxygen impurities. In conclusion, we also demonstrate the feasibility of depositing thick hydrogenated amorphous carbon films (∼30 μm) for ICF applications.
The purpose of this CRADA is to provide for the joint conduct of research and development (R&D) investigations between Fermi Research Alliance, LLC (Contractor), as operator of the Fermi National Accelerator Laboratory (Fermilab) and Euclid TechLabs, LLC (Participant) related to Research and Development of Advanced Superconducting Radiofrequency (SRF) Accelerator Technology and Components for Scientific and Industrial Applications.
Superconducting radiofrequency (SRF) cavities are critical components of modern particle accelerators. The industrialization of SRF technology in the U.S. has a long history, with several companies becoming interested in the technology in the past 30 years. However, there is currently no U.S. manufacturer with the capability to produce fully assembled, ready-to-test SRF cavities. A majority of these companies have either left the field or shut their doors. As a result, government-sponsored SRF accelerator projects in the U.S. largely rely on European vendors for the cavity supply. This presents not only a supply chain risk for scientific use cases, but also severely limits the commercialization of accelerator-based technologies. SRF accelerators have a range of strategic applications, including environmental remediation, semiconductor lithography, medical isotope production, and irradiation/sterilization. The nurturing of a domestic SRF industry is critical to maintaining U.S. economic competitiveness.
Particle accelerators are considered as an important device that has wide applications in cancer treatment, sterilizing waste, preserving foods, ion implantation in semiconductor industry, and in production of isotopes for medical applications. Superconducting radiofrequency (SRF) cavities are the building blocks of a linear particle accelerator. Current particle accelerators use niobium (Nb) superconductors as the sheet material to fabricate a single SRF cavity for particle acceleration. With better superconducting properties (critical temperature Tc ~ 18.3 K, superheating field Hsh~ 400 mT), Nb3Sn is considered a potential candidate in SRF technology. Magnetron sputtering is a promising deposition method to fabricate Nb3Sn thin films inside SRF cavities. Superconducting Nb3Sn films were fabricated on Nb and sapphire substrates by magnetron sputtering from a single stoichiometric Nb3Sn target, by multilayer sputtering of Nb and Sn followed by annealing, and by co-sputtering of Nb and Sn followed by annealing. The variation of morphological and superconducting properties was investigated for different substrate temperatures, annealing temperatures, annealing durations, and thicknesses. The film properties were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy dispersive X-ray spectroscopy (EDS). The films had crystalline Nb3Sn structure without any presence of poor superconducting Nb6Sn5 and NbSn2 phases. The highest Tc of the films fabricated from the stoichiometric target, multilayer sputtering and co-sputtering were 17.44, 17.93, and 17.66 K respectively. Finally, a cylindrical sputter coater with two identical magnetrons was designed and commissioned to fabricate Nb3Sn films inside a 2.6 GHz SRF cavity. The magnetrons were installed facing opposite to each other in a custom designed vacuum chamber and multilayers of Nb and Sn films on 1 cm2 Nb substrates replicating the beam tubes and equator locations of the cavity and the coated multilayered films were annealed at 950 °C for 3 h. The XRD of the as?deposited and annealed films confirmed the formation of Nb3Sn after the annealing. The dissertation discusses the fabrication process, characterized results of the fabricated films, the design of the cylindrical sputter coater and the preliminary data obtained from the sputter coater.
Additive manufacturing is a versatile technique that shows promise in providing quick and dynamic manufacturing for complex engineering problems. Research has been ongoing into the use of additive manufacturing for potential applications in radiofrequency (RF) component technologies. Here, we present a method for developing an effective prototype load produced from 316L stainless steel on a direct metal laser sintering machine. The model was tested using simulation software to verify the validity of the design. The load structure was manufactured by an online digital manufacturing company, showing the viability of using easily accessible tools to manufacture RF structures. The produced load was able to produce an S11 value of −22.8 dB at a C-band frequency of 5.712 GHz while under a vacuum. In a high-power test, the load was able to terminate a peak power of 8.1 MW. The discussion includes future applications of the present method and how it will help to improve the implementation of future accelerator concepts.
Radiofrequency radiation and particle acceleration from solar flare filaments due to rotational collective motion of electrons or ions
Increased production of atomic hydrogen ion in low pressure radiofrequency discharge by two step process
Radiofrequency noise measurements in urban areas at 480 and 950 megahertz
Irregularly shaped surfaces, such as lubrication system components (ball bearings, seals, gears, etc.), can be coated on all surfaces, including irregular shapes, when radiofrequency sputtering is used. When the specimen is properly located with respect to the sputtering target, the sputtered material covers the entire surface of the object irrespective of its geometrical configuration. An adherent, dense film is formed. The film thickness varies from 20 to 50 percent on, for example, a hearing cage or race depending on its geometry. When sputtered solid film lubricants such as molybdenum disulfide are used, a film thickness only of the order of 10 to the minus 7th power m (thousands of angstroms) is required at the contacting areas. It is only essential to determine the required film thickness at the critical areas in need of lubrication. The sections outside the areas to be lubricated fall within the thickness deviation range of 20 to 50 percent, which still constitutes a negligible change respect to tolerance requirements.
The adherence, friction, and wear properties of thin hard refractory compound coatings applied to 440C bearing steel by radiofrequency sputtering were investigated. Friction and wear tests were done with nonconforming pin on disk specimens. The compounds examined were chromium carbide, molybdenum silicide, and titanium carbide. The adherence, friction, and wear were markedly improved by the application of a bias voltage to the bearing steel substrate during coating deposition. Analysis by X-ray photoelectron spectroscopy indicated that the improvement may be due to a reduction in impurities in bias deposited coatings. A fivefold reduction in oxygen concentration in MoSi2 coating by biasing was noted. Chromium carbide was not effective as an antiwear coating. Molybdenum silicide provided some reduction in both friction and wear. Titanium carbide exhibited excellent friction and antiwear properties at light loads. Plastic flow and transfer of the coating material onto the pin specimen appears to be important in achieving low friction and wear.