Search NASA⌕ Search

SEARCH · Search NASA

Results for “RECOMBINATION COEFFICIENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Unexpected origin of the quantum efficiency reduction in long-wavelength (In,Ga)⁢N light-emitting diodes

Differential carrier lifetime (DCL) measurements were performed on c-plane In 𝑥 ⁢Ga 1−𝑥⁢ N/Ga⁢N single-quantum-well (QW) light-emitting diodes (LEDs) with varying indium-content QWs (x = 13.5%, 16%, 22%), emitting with violet, blue, and green wavelengths. The recombination lifetimes of LEDs were found to increase with increasing indium composition, resulting in increased carrier densities n measured by DCL. Extraction of the A coefficients, which are assumed to not vary with n, and of the effective B(n) and C(n) coefficients of the ABC model of the internal quantum efficiency (IQE) of QWs showed no significant changes in the A coefficient with increasing indium content [In] in the In 𝑥 ⁢Ga 1−𝑥 ⁢N QW, and a reduction in the B(n) and C(n) coefficients with increasing [In]. When looking at the Shockley-Read-Hall (SRH) recombination rate An, the radiative recombination rate B(n)𝑛 2 , and the Auger-Meitner (AM) recombination rate C(n)𝑛 3 , we observed that at any given n, the SRH rate is the same for the three [In] measured, while the radiative rate decreases (by up to approximately 9 times) and the AM rate decreases (by up to approximately 7 times) with increasing indium content. This shows that the larger reduction in radiative recombination rates relative to nonradiative recombination rates with increasing [In] is the largest contributor to the decreased quantum efficiencies of LEDs (the “green gap”) at any given n. While some of the reduction in the effective recombination coefficients B(n) and C(n) can be explained by the reduced wave-function overlaps of the QW with increasing indium content, the larger reduction of B(n) relative to C(n) motivates further study of the intrinsic recombination coefficients 𝐵 0 and 𝐶 0 of bulk In 𝑥 ⁢Ga 1−𝑥 ⁢N alloys and how they are related to the effective recombination coefficients B(n) and C(n) in QWs. The relative contributions of nonradiative recombination are enhanced at any given current density due to the sublinear relationship between the carrier density n and the current density. Thus, the solution to the green gap, up to any intrinsic limitations set by the indium content of the QW, from an IQE perspective, requires the design of long-wavelength (In,Ga)⁢N LEDs with improved wave-function overlaps that can operate with a lower carrier density at any given current density.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

An Experimental and Theoretical Study of the High Temperature Reactions of the Four Butyl Radical Isomers

The high temperature gas phase chemistry of the four butyl radical isomers (n-butyl,sec-butyl, iso-butyl, andtert-butyl) was investigated in a combined experimental and theoretical study. Organic nitrites were used as convenient and clean sources of each of the butyl radical isomers. Rate coefficients for dissociation of each nitrite were obtained experimentally and are at, or close to, the high pressure limit. Low pressure experiments were performed in a diaphragmless shock tube with laser schlieren densitometry at post-shock pressures of 65, 130, and 260 Torr and post-shock temperatures of 700-1000 K. Additional experiments were conducted with iso-butyl radicals at 805 K and 8.7 bar to elucidate changes in mechanism at higher pressures. These experiments were performed in a miniature shock tube with synchrotron-based photoionization mass spectrometry. The mass spectra confirmed that scission of the O-NO bond is the primary channel by which the precursors dissociate, but they also provided evidence of a minor channel (<7.7%) through HNO loss and formation of an aldehyde. These high pressure experiments were also used to determine the disproportionation/recombination ratio for iso-butyl radicals as 0.3. Reanalysis of the lower-temperature literature and the present data yielded rate constants for the disproportionation reaction, iso-butyl + iso-butyl = iso-butene + iso-butane. A chemical kinetics model was developed for the reactions of the butyl isomers that included new paths for highly energized adducts. These adducts are formed by the addition of H, CH 3 or C 2 H 5 to the butyl radicals. Accompanying theoretical investigations show that chemically activated pathways are competitive with stabilization of the adduct by collision under the conditions of the laser schlieren experiments. These calculations also show that at 10 bar and T< 1000 K stabilization is the only important reaction, but at higher temperatures, even at 10 bar, chemically activated product channels should also be considered. Branching fractions and rate coefficients are presented for these reactions. Furthermore, this study also highlights the importance of the radical structure for determining branching ratios for disproportionation and recombination of alkyl radicals, and these were facilitated by theoretical calculations of recombination rate coefficients for the four butyl radical isomers. Overall, the results reveal previously unknown features of butyl radical chemistry under conditions that are relevant to a wide range of applications and reaction mechanisms are presented that incorporate pressure dependent rate coefficients for the key steps.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Continuous polymer films deposited on top of porous substrates using plasma-enhanced atomic layer deposition and molecular layer deposition

Molecular layer deposition (MLD) is able to produce ultrathin polymer films with control over thickness, cross-linking, and chemical composition. With these capabilities, MLD should be useful in the fabrication of novel polymer membranes on porous supports. However, confining a continuous MLD film to the surface of porous substrates is difficult because of MLD film growth in the pores. The deposition in the pores lowers the conductance of the porous support. This paper presents a method to deposit continuous polymer films on top of porous substrates. In this method, Al2O3 plasma-enhanced atomic layer deposition (PE-ALD) using trimethylaluminum and oxygen plasma as the reactants was first used to cap the pores of the substrate. Subsequently, a polyamide MLD film was deposited on the Al2O3 PE-ALD capping layer using m-phenylenediamine and trimesoyl chloride as the reactants. The Al2O3 pore caps were then removed from the porous substrate by etching from the backside using a timed exposure to a dilute sodium hydroxide solution. This method was demonstrated using anodic aluminum oxide (AAO) and polyethersulfone (PES) porous substrates. Al2O3 PE-ALD film growth was limited to the top of the porous substrate, resulting in rapid surface recombination or high sticking coefficients for the reactive plasma species within the pores. Gas permeance measurements confirmed the pore capping of the AAO substrates. The reopening of the pores by dissolving the Al2O3 pore caps with a sodium hydroxide solution was monitored using gas permeance versus etch time. The removal of the Al2O3 pore caps from the PES substrates could also dissolve the Al2O3 layer underneath the MLD film. The loss of this Al2O3 layer led to the detachment of the MLD film from the PES substrate. However, the MLD film could be anchored to the PES support at fractures located in the Al2O3 film prior to the MLD. The Al2O3 film fracture allowed the MLD film to anchor firmly to the PES substrate by MLD in the pores of the PES porous substrate. The distance between the anchor points was a function of fracture density. This distance could be controlled by applying a tensile stress to the Al2O3 PE-ALD film to fracture the film through sample bending. This method produced firmly anchored polymer MLD films on top of the PES porous substrates.

Welch, Brian C. (ORCID:000000029747045X)↗
DOE OSTI2023

Thermodynamic Limit for Excitonic Light-Emitting Diodes

Here, we derive the thermodynamic limit for organic light-emitting diodes (OLEDs), and show that strong exciton binding in these devices requires a higher voltage to achieve the same luminance as a comparable inorganic LED. The OLED overpotential, which does not reduce the power conversion efficiency, is minimized by having a small exciton binding energy, a long exciton lifetime, and a large Langevin coefficient for electron-hole recombination. Based on these results, it seems likely that the best phosphorescent and thermally activated delayed fluorescence OLEDs reported to date approach their thermodynamic limit. The framework developed here is broadly applicable to other excitonic materials, and should therefore help guide the development of low voltage LEDs for display and solid-state lighting applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Development, Implementation, and Verification of Partially-Ionized Collisional Multifluid Plasma Models in Drekar

We consider the development of multifluid models for partially ionized multispecies plasmas. The models are composed of a standard set of five-moment fluid equations for each species plus a description of electromagnetics. The most general model considered utilizes a full set of fluid equations for each charge state of each atomic species, plus a set of fluid equations for electrons. The fluid equations are coupled through source terms describing electromagnetic coupling, ionization, recombination, charge exchange, and elastic scattering collisions in the low-density coronal limit. The form of each of these source terms is described in detail, and references for required rate coefficients are identified for a diverse range of atomic species. Initial efforts have been made to extend these models to incorporate some higher-density collisional effects, including ionization potential depression and three- body recombination. Some reductions of the general multifluid model are considered. First, a reduced multifluid model is derived which averages over all of the charge states (including neutrals) of each atomic species in the general multifluid model. The resulting model maintains full consistency with the general multifluid model from which it is derived by leveraging a quasi-steady-state collisional ionization equilibrium assumption to recover the ionization fractions required to make use of the general collision models. Further reductions are briefly considered to derive certain components of a single-fluid magnetohydrodynamics (MHD) model. In this case, a generalized Ohm's law is obtained, and the standard MHD resistivity is expressed in terms of the collisional models used in the general multifluid model. A number of numerical considerations required to obtain robust implementations of these multifluid models are discussed. First, an algebraic flux correction (AFC) stabilization approach for a continuous Galerkin finite element discretization of the multifluid system is described in which the characteristic speeds used in the stabilization of the fluid systems are synchronized across all species in the model. It is demonstrated that this synchronization is crucial in order to obtain a robust discretization of the multifluid system. Additionally, several different formulations are considered for describing the electromagnetics portion of the multifluid system using nodal continuous Galerkin finite element discretizations. The formulations considered include a parabolic divergence cleaning method and an implicit projection method for the traditional curl formulation of Maxwell's equations, a purely- hyperbolic potential-based formulation of Maxwell's equations, and a mixed hyperbolic-elliptic potential-based formulation of Maxwell's equations. Some advantages and disadvantages of each formulation are explored to compare solution robustness and the ease of use of each formulation. Numerical results are presented to demonstrate the accuracy and robustness of various components of our implementation. Analytic solutions for a spatially homogeneous damped plasma oscillation are derived in order to verify the implementation of the source terms for electromagnetic coupling and elastic collisions between fluid species. Ionization balance as a function of electron temperature is evaluated for several atomic species of interest by comparing to steady-state calculations using various sets of ionization and recombination rate coefficients. Several test problems in one and two spatial dimensions are used to demonstrate the accuracy and robustness of the discretization and stabilization approach for the fluid components of the multifluid system. This includes standard test problems for electrostatic and electromagnetic shock tubes in the two-fluid and ideal shock-MHD limits, a cylindrical diocotron instability, and the GEM challenge magnetic reconnection problem. A one-dimensional simplified prototype of an argon gas puff configuration as deployed on Sandia's Z-machine is used as a demonstration to exercise the full range of capabilities associated with the general multifluid model.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Impact of dopant-induced band tails on optical spectra, charge carrier transport, and dynamics in single-crystal CdTe

Abstract Cadmium telluride (CdTe) semiconductors are used in thin-film photovoltaics, detectors, and other optoelectronic applications. For all technologies, higher efficiency and sensitivity are achieved with reduced charge carrier recombination. In this study, we use state-of-the-art CdTe single crystals and electro-optical measurements to develop a detailed understanding of recombination rate dependence on excitation and temperature in CdTe. We study recombination and carrier dynamics in high-resistivity (undoped) and arsenic (As)-doped CdTe by employing absorption, the Hall effect, time-resolved photoluminescence, and pump-probe in the 80–600 K temperature range. We report extraordinarily long lifetimes (30 µs) at low temperatures in bulk undoped CdTe. Temperature dependencies of carrier density and mobility reveal ionization of the main acceptors and donors as well as dominant scattering by ionized impurities. We also distinguish different recombination defects. In particular, shallow As Te and deep V Cd −As Cd acceptors were responsible for p-type conductivity. AX donors were responsible for electron capture, while nonradiative recombination centers (V Cd −As Te , As 2 precipitates), and native defects (V Cd −Te Cd ) were found to be dominant in p-type and n-type CdTe, respectively. Bimolecular and surface recombination rate temperature dependencies were also revealed, with bimolecular coefficient T −3/2 temperature dependence and 170 meV effective surface barrier, leading to an increase in surface recombination velocity at high temperatures and excitations. The results of this study allowed us to conclude that enhanced crucible rotation growth of As-doped CdTe is advantageous to As activation, leading to longer lifetimes and larger mobilities and open-circuit voltages due to lower absorption and trapping.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Assessing Carrier Mobility, Dopability, and Defect Tolerance in the Chalcogenide Perovskite Ba Zr S 3

The chalcogenide perovskite Ba Zr S 3 has attracted much attention as a promising solar absorber for thin-film photovoltaics. Here we use first-principles calculations to evaluate its carrier transport and defect properties. We find that Ba Zr S 3 has a phonon-limited electron mobility of 37 cm 2 / V s, which is comparable to that in halide perovskites, but lower hole mobility of 11 cm 2 / V s. The defect computations indicate that Ba Zr S 3 is intrinsically n -type due to shallow sulfur vacancies, but that strong compensation by sulfur vacancies will prevent attempts to make it p -type. We also establish that Ba Zr S 3 shows some degree of defect tolerance, presenting only few low formation energy, deep intrinsic defects. Among the deep defects, sulfur interstitials are the dominant nonradiative recombination centers but exhibit a moderate capture coefficient. Our work highlights the material’s intrinsic limitations in carrier mobility and p -type doping, and suggests focusing on suppressing the formation of sulfur interstitials to achieve longer carrier lifetime. Published by the American Physical Society 2024

Yuan, Zhenkun (ORCID:0000000272005973)↗
DOE OSTI2021

Minimizing hydrogen vacancies to enable highly efficient hybrid perovskites

Defect-induced non-radiative losses are currently limiting the performance of hybrid perovskite devices. Experimental reports have indicated the existence of point defects that act as detrimental non-radiative recombination centres under iodine-poor synthesis conditions. However, the microscopic nature of these defects is still unknown. Here we demonstrate that hydrogen vacancies can be present in high densities under iodine-poor conditions in the prototypical hybrid perovskite MAPbI 3 (MA = CH 3 NH 3 ). They act as very efficient non-radiative recombination centres with an exceptionally high carrier capture coefficient of 10 –4 cm 3 s –1 . By contrast, the hydrogen vacancies in FAPbI 3 [FA = CH(NH 2 ) 2 ] are much more difficult to form and have a capture coefficient that is three orders of magnitude lower. Our study unveils the critical but overlooked role of hydrogenvacancies in hybrid perovskites and rationalizes why FA is essential for realizing high efficiency in hybrid perovskite solar cells. Furthermore, minimizing the incorporation of hydrogen vacancies is key to enabling the best performance of hybrid perovskites.

14 SOLAR ENERGY↗
DOE OSTI2021

Nonrad: Computing nonradiative capture coefficients from first principles

Point defects in semiconductor crystals provide a means for carriers to recombine nonradiatively. This recombination process impacts the performance of devices. We present the Nonrad code that implements the first-principles approach of Alkauskas et al. (2014) [8] for the evaluation of nonradiative capture coefficients based on a quantum-mechanical description of the capture process. An approach for evaluating electron-phonon coupling within the projector augmented wave formalism is presented. We also show that the common procedure of replacing Dirac delta functions with Gaussians can introduce errors into the resulting capture rate, and implement an alternative scheme to properly account for vibrational broadening. Finally, we assess the accuracy of using an analytic approximation to the Sommerfeld parameter by comparing with direct numerical evaluation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Anomalous Auger Recombination in PbSe

Using first-principles approaches we find that the Auger recombination in PbSe is anomalous in three distinct ways. First, the direct Auger coefficient is 4 orders of magnitude lower than that of other semiconductors with similar band gaps, a result that can be attributed to the lack of involvement of a heavy-hole band. Second, phonon-assisted indirect Auger recombination prevails, contrary to the common belief that direct Auger is dominant in narrow-gap semiconductors. Third, an unexpectedly weak temperature dependence of the Auger coefficient is observed, which we can now attribute to the indirect nature of the Auger process. The widely accepted explanation of this behavior in terms of an unusual temperature dependence of the band gap is only a secondary effect. Furthermore, our results elucidate the mechanisms underlying the anomalous Auger recombination in IV-VI semiconductors in general, which is critical for understanding and engineering carrier transport.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Understanding radiation effects in friction stir welded MA956 using ion irradiation and a rate theory model

We report an outstanding challenge in the manufacturing and joining of oxide dispersion strengthened steels is retaining the nanofeatures in the alloy throughout the fabrication and welding process. MA956 was friction stir welded with two different sets of welding parameters, resulting in a medium and high heat input. After welding, 5 MeV Fe ++ ion irradiations were performed at doses ranging from 50 to 200 dpa in the temperature range of 400 to 500°C. Post-irradiation characterization was performed with scanning transmission electron microscopy and energy-dispersive x-ray spectroscopy to investigate the Y-Al-O dispersoids, voids, and dislocations. After welding, the dispersoid microstructure coarsened, resulting in fewer and larger dispersoids regardless of heat input. After irradiation, the dispersoid behavior in the welded material was sensitive to temperature, exhibiting growth behavior attributed to Ostwald coarsening at 500 °C but a mixture of nucleation and more muted growth at 400 and 450 °C, attributed to competing mechanisms of radiation-enhanced diffusion and Ostwald coarsening. Void swelling correlated to heat input; being more prevalent in the welded conditions occurring at lower doses and in higher values relative to the base material. The low values of swelling despite microstructure coarsening caused by welding demonstrate the excellent swelling resistance of MA956, even after welding with the highest swelling values of 0.5% noted in the stir zone high heat input condition at 450 °C, 200 dpa. The dislocation behavior was inconsistent: the strongest trend was that network density was higher for welded versus base material, and an increase in loop diameter with temperature was observed. A rate theory model based on the observed microstructure suggests at high temperature interstitial loss to sinks was more likely to be dominant compared to mutual annihilation via point defect recombination, because of an increase of the radiation diffusion coefficient with temperature regardless of initial welded microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dynamics of carrier injection through V-defects in long wavelength GaN LEDs

The efficiency of high-power operation of multiple quantum well (QW) light emitting diodes (LEDs) to a large degree depends on the realization of uniform hole distribution between the QWs. In long wavelength InGaN/GaN QW LEDs, the thermionic interwell hole transport is hindered by high GaN barriers. However, in polar LED structures, these barriers may be circumvented by the lateral hole injection via semipolar {$10\bar{1}1$} QWs that form on the facets of V-defects. The efficiency of such carrier transfer depends on the transport time since transport in the semipolar QWs is competed by recombination. In this work, we study the carrier transfer from the semipolar to polar QWs by time-resolved photoluminescence in long wavelength (green to red) LEDs. We find that the carrier transfer through the semipolar QWs is fast, a few tens of picoseconds with the estimated room temperature ambipolar diffusion coefficient of ∼5.5 cm 2 /s. With diffusion much faster than recombination, the hole transport from the p-side of the structure to the polar QWs should proceed without a substantial loss, contributing to the high efficiency of long wavelength GaN LEDs.

Crystallographic defects↗
DOE OSTI2023

Iodine Vacancies do not Cause Nonradiative Recombination in Halide Perovskites

The iodine vacancy (V I ) has frequently been discussed as a strong nonradiative recombination center in halide perovskites. This proposition was mainly based on the presence of charge-state transition levels in the band gap, as found in early first-principles calculations. In this work, we perform accurate hybrid-density-functional calculations for V I in CsPbI 3 , CsSnI 3 , and CsGeI 3 and find that V I does not have any transition levels in the band gap in CsPbI 3 , in contrast to the results from calculations based on semilocal functionals. The iodine vacancy V I does introduce levels in the band gap in CsSnI 3 and CsGeI 3 , but our explicitly computed nonradiative capture coefficients demonstrate that V I has a negligible impact on nonradiative recombination. Our study corrects a misunderstanding of the role of V I in the iodide-based perovskites, and shifts the focus toward identifying and mitigating actual recombination centers in order to further improve the optoelectronic performance.

14 SOLAR ENERGY↗
DOE OSTI2020

Strain dependence of Auger recombination in 3 μm GaInAsSb/GaSb type-I active regions

We differentiate the effect of strain induced by lattice-mismatched growth from strain induced by mechanical deformation on cubic nonradiative Auger recombination in narrow-gap GaInAsSb/GaSb quantum well (QW) heterostructures. The typical reduction in the Auger coefficient observed with lattice-mismatched growth appears to be due to the concomitant compositional change rather than the addition of strain, with implications for mid-IR semiconductor laser design. We induced a range of internal compressive strain in five samples from -0.90% to -2.07% by varying the composition during the growth and mechanically induced a similar range of internal strain in analogous quantum well membrane samples. We performed time-resolved photoluminescence and differential reflectivity measurements to extract the carrier recombination dynamics, taken at 300 K with carrier densities from 2.7 × 10 18 cm -3 to 1.4 × 10 19 cm -3 . We observed no change with strain in the cubic Auger coefficient of samples that were strained mechanically, but we did observe a trend with strain in samples that were strained by the QW alloy composition. Measured Auger coefficients ranged from 3.0 × 1 0 - 29 cm 6 s -1 to 3.0 × 1 0 - 28 cm 6 s -1 .

36 MATERIALS SCIENCE↗
DOE OSTI2021

Numerical Simulations of Time-Resolved Photoluminescence in CdSexTe1-x/CdTe Solar Cells

We present initial time-resolved photoluminescence (TRPL) simulations in graded CdSexTe1-e thin-film solar cells to quantify the front-interface recombination velocity, S int,front . Our model includes several composition dependences: bandgap energy, absorption coefficient, electron affinity, and carrier lifetime. Cathodoluminescence spectrum imaging measurements on bevels provide an estimate of the bandgap and the CdSe x Te 1-x alloy composition through the absorber thickness. TRPL decays are simulated as a function of the laser power, S int,front , front-interface band offset, and bulk Shockley-Read-Hall lifetime. We find the impact of S intf,ront on the PL decay increases as the band offset shifts from a "spike" to a "cliff". Recombination rate analysis shows that back-interface recombination could potentially dictate the later part of the TRPL decay "t 2" in high-lifetime CdSe x Te 1-x cells. We briefly discuss ongoing work to determine TRPL measurement conditions that maximize sensitivity to S itnt,front.

CdTe solar cells↗
DOE OSTI2025

Comprehensive model for evaluating voltage losses and performance improvements in thin-film photovoltaic devices

Progress of state-of-the-art and next-generation thin-film photovoltaic devices is often stymied by open-circuit voltage (𝑉 oc ) that is significantly lower than theoretical and practical limits. Yet, effectively diagnosing the primary sources of voltage loss remains challenging. Herein, a sequence of device-level characterization techniques and simulations are employed to identify and rank loss mechanisms. For the research-based Cd⁡(Se,Te) device under study, most of the loss was at the front semiconductor heterointerface due to a clifflike conduction-band offset that lowered the recombination activation energy. Additional losses due to band tails were quantified by photoluminescence analysis. The latter provided the absorption coefficient and activation energy reduction associated with band tails as inputs to device models. Simulations showed that alleviating front-interface issues would improve 𝑉 oc , but it would then be limited by bulk recombination. Further improvement of the bulk would then lead to back-contact limitations. Reducing band tails is beneficial in any circumstance. In conclusion, this analysis provides guidance for reaching toward the radiative 𝑉 oc limit.

14 SOLAR ENERGY↗
DOE OSTI2022

Non-Equilibrium Doping of Poly-Si:Ga/SiOx Passivating Contacts Solar Cells

In this contribution, we show that Ga-hyperdoped poly-Si/SiOx contacts are realized by pulsed laser annealing and post-hydrogenation. The motivation behind this work is to improve the inferior performance of boron-doped poly- Si/SiOx contacts when compared to the phosphorus-doped contacts. Here we used Ga as a novel p-type dopant to replace B, as B is known to accumulate at the interface between the oxide and the crystalline silicon and cause recombination. Due to a high diffusivity of Ga in oxide and a much higher segregation coefficient (Si:SiOx), Ga is shown to be immune to the oxide pileup phenomenon. However, Ga has a low solid solubility limit in Si (5x10^19 cm-3), which is not enough to form a low resistivity contact. To overcome this problem, we explored pulsed laser annealing via excimer laser by varying the laser energy densities and pulses. The passivation and electrical properties are studied systematically using photoluminescence (PL), secondary ion mass spectrometry (SIMS), and Van der Pauw-Hall measurements. We show an active Ga doping concentration above 1x10^20 cm^-3, which is above the solid solubility limit of Ga in Si. Good passivation quality is demonstrated with the highest implied Voc (iVoc) of 721 mV on single side polished samples. Furthermore, a low diode contact resistivity of ~22 m..omega.. cm^2 is obtained using Ti/Ag contacts, with minimal metal-to-semiconductor contact resistivity of 0.9 m..omega.. cm^2.

non-equilibrium doping↗
DOE OSTI2021

Four Isotope-Labeled Recombination Pathways of Ozone Formation

A theoretical approach is developed for the description of all possible recombination pathways in the ozone forming reaction, without neglecting any process a priori, and without decoupling the individual pathways one from another. These pathways become physically distinct when a rare isotope of oxygen is introduced, such as 18 O, which represents a sensitive probe of the ozone forming reaction. Each isotopologue of O 3 contains two types of physically distinct entrance channels and two types of physically distinct product wells, creating four recombination pathways. Calculations are done for singly and doubly substituted isotopologues of ozone, eight rate coefficients total. Two pathways for the formation of asymmetric ozone isotopomer exhibit rather different rate coefficients, indicating large isotope effect driven by ΔZPE-difference. Rate coefficient for the formation of symmetric isotopomer of ozone (third pathway) is found to be in between of those two, while the rate of insertion pathway is smaller by two orders of magnitude. These trends are in good agreement with experiments, for both singly and doubly substituted ozone. The total formation rates for asymmetric isotopomers are found to be somewhat larger than those for symmetric isotopomers, but not as much as in the experiment. Altogether, the distribution of lifetimes is found to be very similar for the metastable states in symmetric and asymmetric ozone isotopomers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗