Search NASA⌕ Search

SEARCH · Search NASA

Results for “RRR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

28 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Rutherford-in-Copper-Channel Conductor for the MARCO Solenoidal Detector Magnet

MARCO will be a superconducting solenoid for a new particle physics detector of the upcoming Electron Ion Collider (EIC) at Brookhaven National Laboratory (NY, USA). The design field at the interaction point is 2.0 T with a nominal current of about 4 kA at 4.5 K. For this magnet, an aluminumstabilized conductor was considered at the very preliminary design phase. After that, since the lack of manufacturers able to deal with aluminum extrusion, copper has been chosen as stabilizer. Thanks to a dedicated design effort, the copper stabilizer and accompanying material choices provided acceptable hadronic interaction length. The conductor is based on a NbTi Rutherford cable that is soldered in a U-shaped copper profile. Here, this paper goes through the definition of the conductor crosssection according to the project requirements and the supplier capabilities. Its characteristics will be detailed and discussed, in particular the RRR and the yield strength of the copper channel needed for protection and mechanics respectively. Finally, a proposal on how to make the joint between two conductors is presented.

Stacchi, Francesco [Commissariat a l'Energie Atomi↗
DOE OSTI2025

Impact of Annealing on the Chemical and Superconducting Properties of Ta Thin Films

Tantalum thin films are annealed to dissolve the surface oxide. The effect of annealing is studied using material characterization tools, XPS and TOF-SIMS, and electrical transport measurements of the annealed films are taken using standard PPMS methods to correlate with the surface chemistry. Annealing dissociates the surface oxide, and the oxygen produced diffuses into the thin film. The introduction of oxygen reduces the quality of the thin film, as shown by the suppression of Tc and a reduction in RRR.

Shinde, Maithilee [IIT, Chicago]↗
DOE OSTI2026

Impact of Annealing on Superconducting Properties of Tantalum Thin Films

The pursuit for higher-coherence superconducting qubits has led to the adoption of new materials and innovative fabrication techniques. Among the commonly used superconducting materials, tantalum-based or tantalum-capped superconducting qubits have demonstrated the longest lifetimes, outperforming niobium devices even in the presence of their native oxides. Given the losses introduced by the surface oxide, one method to further improve performance is to reduce or eliminate the native oxide on tantalum through UHV annealing. In this work, we examine the effect of dissolved oxygen as a function of annealing temperature on the superconducting properties of tantalum thin films. Dissolved oxygen is quantified using atom probe tomography (APT) and secondary ion mass spectrometry (TOF-SIMS) and correlated with electromagnetic transport measurements performed using a Physical Property Measurement System (PPMS). This study observes that annealing decomposes the native oxide and drives oxygen diffusion into the film matrix. Increasing oxygen content decreases the superconducting transition temperature (Tc) and the residual resistivity ratio (RRR). The critical field decreases with the incorporation of oxygen, while the film’s coherence length decreases relatively by 5%. These results, as well as findings from ongoing studies linking fabrication processes to the structural and chemical properties of the superconducting film and Josephson junction, provide insight into effective strategies for improving the performance of superconducting devices.

Shinde, Maithilee [IIT, Chicago; Fermilab]↗
NASA NTRS1977

The stereoisomeric composition of phytanyl chains in lipids of Dead Sea sediments

Lipid extracts from five recent Dead Sea sediments were analyzed for isoprenoid compounds and the following were isolated: free and phospholipid-bound di-O-phytanylglycerol, free phytanol and free and esterified phytanic acid. The phytanyl groups of the diether and the free phytanol were oxidized to the corresponding phytanic acid; the stereoisomeric composition of the derived phytanic acids as well as of the ester-bound phytanic acid was determined by open-tubular gas-liquid chromatography of the corresponding methyl esters on butanediolsuccinate polyester. Only the 3R, 7R, 11R-isomer of phytanic acid was detected in each of the phytanate samples, indicating that these phytanyl chains in the Dead Sea sediments are most likely derived from extremely halophilic bacteria rather than from phytol of chlorophyll origin. These findings also provide further evidence that the mixtures of RRR and SRR-phytanic acids previously isolated from organic-rich shales were most likely derived from the phytyl chain in chlorophyll.

Anderson, R.↗
NASA NTRS2007

Absorber Materials for Transition-Edge Sensor X-ray Microcalorimeters

Arrays of superconducting transition-edge sensors (TES) can provide high spatial and energy resolution necessary for x-ray astronomy. High quantum efficiency and uniformity of response can be achieved with a suitable absorber material, in which absorber x-ray stopping power, heat capacity, and thermal conductivity are relevant parameters. Here we compare these parameters for bismuth and gold. We have fabricated electroplated gold, electroplated gold/electroplated bismuth, and evaporated gold/evaporated bismuth 8x8 absorber arrays and find that a correlation exists between the residual resistance ratio (RRR) and thin film microstructure. This finding indicates that we can tailor absorber material conductivity via microstructure alteration, so as to permit absorber thermalization on timescales suitable for high energy resolution x-ray microcalorimetry. We show that by incorporating absorbers possessing large grain size, including electroplated gold and electroplated gold/electroplated bismuth, into our current Mo/Au TES, devices with tunable heat capacity and energy resolution of 2.3 eV (gold) and 2.1 eV (gold/bismuth) FWHM at 6 keV have been fabricated.

Brown, Ari-David↗
NASA NTRS2012

Design of High Resolution Soft X-Ray Microcalorimeters Using Magnetic Penetration Thermometers

We have designed high-resolution soft x-ray microcalorimeters using magnetic penetration thermometers (MPTs) in an array of pixels covering a total of 2 square centimeters to have a resolving power of 300 at energies around 300 eV. This performance is desirable for studying the soft x-ray background from the warm hot intergalactic medium. MPT devices have small sensor heat capacity and high responsivities, which makes them excellent detector technology for attempting to attain sub-eV resolution. We are investigating the feasibility of pixels with absorbers that are 625 x 625 square micrometers, up to 1 x 1 square millimeters in area and 0.35 micrometer thick and thinner. Our tests have shown that suspended gold absorbers 0.35 micrometers thick (RRR = 6.7) are feasible to fabricate. We modeled the thermal diffusion from such thin gold over the size of a 625 x 625 square micrometer absorber, and conclude that the effect of the thermalization on the resolution of a 300 eV photon is an additional approximately 0.2 eV FWHM of broadening. We discuss the thermal effects of small absorber attachment sterns on solid substrate, as well as considerations for multiplexed readout. We will present the progress we have made towards building and testing this soft x-ray detector.

Busch. Sarah↗
DOE OSTI2025

Investigation of the approach used in the unresolved resonance region

The typical practice used in Monte Carlo neutron transport codes in the unresolved resonance region (URR) is to take advantage of the probability table (PT) approach. Cross sections are sampled from PTs and used as needed, along with generated average cross sections. The PTs are generated based on cross-section calculations performed using the single-level Breit–Wigner approximation. Although the approach used in the URR seems plausible, a detailed examination was needed to understand the benchmark results obtained using specific tests.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗