SEARCH · Search NASA

Results for “Rotor Hover Test”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1997

Measurement of Vortex Strength and Core Diameter in the Wake of a Hovering Rotor

Detailed hot wire measurements have been acquired in the tip vortex of a three-bladed model tilt rotor in hover. Testing was conducted at a rotor tip speed of 752 ft/sec, a Reynolds number (based on blade tip chord) of 1.77 x 10(exp 6), for thrust coefficients up to 0.0160. A figure shows the hot wire mounted above the inverted rotor at the Outside Aerodynamic Rotor Facility (OARF) at NASA Ames Research Center. Strobed shadowgraph flow visualization was used to define the vortex trajectory as an aid in hot wire positioning. Considerable variations in tip vortex structure with time were observed, even from the same blade, under essentially uniform test conditions. The only velocity signatures analyzed were those corresponding to passage of the probe directly through the center of the vortex. These time histories were ensemble averaged after compensating for jitter in the vortex arrival time at the probe, thereby retaining the core structure with minimal smearing. An example of a mean velocity signature, after ensemble averaging, is shown. The mean velocity signature was analyzed under the assumption of constant (unknown) translation speed of the vortex filament past the fixed probe. The translation speed of the vortex is deduced and the vortex strength and core diameter inferred. The results were highly unexpected. The indicated vortex strength is seen to decrease rapidly after first blade passage. In addition, the core radius is seen to decrease with increasing wake age, not increase as might be expected from simple diffusion.

Wadcock, Alan J.↗

NASA NTRS1983

Experimental study of main rotor/tail rotor/airframe interactions in hover. Volume 1: Text and figures

To assist in identifying and quantifying the relevant parameters associated with the complex topic of main rotor/fuselage/tail rotor interference, a model scale hover test was conducted in the Model Rotor Hover Facility. The test was conducted using the basic model test rig, fuselage skins to represent a UH-60A BLACK HAWK helicopter, 4 sets of rotor blades of varying geometry (i.e., twist, airfoils and solidity) and a model tail rotor that could be relocated to give changes in rotor clearance (axially, laterally, and vertically), can't angle and operating model (pusher or tractor). The description of the models and the tests, data analysis and summary (including plots) are included. The customary system of units gas used for principal measurements and calculations. Expressions in both SI units and customary units are used with the SI units stated first and the customary units afterwords, in parenthesis.

Balch, D. T.↗

NASA NTRS1984

Hover test of a full-scale hingeless helicopter rotor: Aeroelastic stability, performance and loads data

A hover test of a full-scale, hingeless rotor system was conducted in the NASA Ames 40- by 80-foot wind tunnel. The rotor was tested on the Ames rotor test apparatus. Rotor aeroelastic stability, performance, and loads at various rotational speeds and thrust coefficients were investigated. The primary objective was to determine the inplane stability characteristics of the rotor system. Rotor inplane damping data were obtained for operation between 350 and 425 rpm (design speed), and for thurst coefficients between 0.0 and 0.12. The rotor was stable for all conditions tested. At constant rotor rotational speed, a minimum inplane dampling level was obtained at a thrust coefficient approximately = 0.02. At constant rotor lift, a minimum in rotor inplane damping was measured at 400 rpm.

Peterson, R. L.↗

NASA NTRS1949

Hovering and Low-Speed Performance and Control Characteristics of the Kaman Helicopter Rotor System as Determined on the Langley Helicopter Tower. TED No. NACA DE 205

An investigation has been conducted with the Langley helicopter tower to obtain basic performance and control characteristics of the Raman rotor system. Blade-pitch control is obtained in this configuration by utilizing an auxiliary flap to twist the blades. Rotor thrust and power required were measured for the hovering condition and over a range of wind velocities from 0 to 30 miles per hour. The control characteristics and the transient response of the rotor to various control movements were also measured. The hovering-performance data are presented as a survey of the wake velocities and the variation of torque coefficient with thrust coefficient. The power required for the test rotor to hover at a thrust of 1350 pounds and a rotor speed of 240 rpm is approximately 6.5 percent greater than that estimated for a conventional rotor of the same diameter and solidity. It is believed that most of this difference is caused by th e flap servomechanism. The reduction in total power required for sustentation of the single-rotor configuration tested at various wind velocities and at the normal operating rotor thrust was found to be similar to the theoretical and experimental results for ro tors with conventionally actuated pitch. The control effectiveness was determined as a function of rotor speed. Sufficient control was available to give a thrust range of 0 to 1500 pounds and a rotor tilt of plus or minus 7 degrees. The time lag between flap motion and blade-pitch response is approximately 0.02 to 0.03 second. The response of the rotor following the blade-pitch response is similar to that of a rotor with conventionally actuated pitch changes. The over-all characteristics of the rotor investigated indicate that satisfactory performance and control characteristics were obtained.

Carpenter, Paul J.↗

NASA NTRS1978

An experimental investigation of hingeless helicopter rotor-body stability in hover

Model tests of a 1.62 m diameter rotor were performed to investigate the aeromechanical stability of coupled rotor-body systems in hover. Experimental measurements were made of modal frequencies and damping over a wide range of rotor speeds. Good data were obtained for the frequencies of the rotor lead-lag regressing mode. The quality of the damping measurements of the body modes was poor due to nonlinear damping in the gimbal ball bearings. Simulated vacuum testing was performed using substitute blades of tantalum that reduced the effective lock number to 0.2% of the model scale value while keeping the blade inertia constant. The experimental data were compared with theoretical predictions, and the correlation was in general very good.

Bousman, W. G.↗

NASA NTRSDate not supplied

Aeroacoustic Testing of UAS-Scale Rotors for a Quadcopter in Hover and Forward Flight

A series of experiments was conducted in an anechoic chamber and wind tunnel to investigatethe noise and performance of an optimum hovering rotor design. The optimum hovering rotorexperimental data set presented in this paper provides the community with a rotor that istheoretically easier to model. Isolated rotors were tested in an anechoic hover chamber as wellas on a representative quadcopter vehicle. In the anechoic chamber, performance and acousticmeasurements were taken at various rotor speeds to compare to those of a commercial-off-the-shelf (COTS) rotor. In the wind tunnel, free-stream velocity, vehicle pitch, and rotor rotationrates were varied to achieve various hover and forward flight operating conditions. Previousinvestigation of a small quadcopter in the Low Speed Aeroacoustic Wind Tunnel (LSAWT) hadidentified possible broadband and interactional noise sources due to rotor airframe interactionand rotor-rotor interaction. These publications identified separation, turbulent boundary layertrailing edge, and bluntness vortex shedding as the main sources of self-generated airfoil noise.By replacing the COTS rotor with an optimum hovering rotor design, self-generated broadbandnoise was reduced for both hover and forward flight conditions for isolated rotor runs. However,the optimum rotors only reduced noise levels for full-vehicle hover conditions, and had little tono reduction in full-vehicle forward flight conditions.

Nicole A Pettingill↗

NASA NTRS1988

Effect of advanced rotorcraft airfoil sections on the hover performance of a small-scale rotor model

A hover test was conducted on a small scale rotor model for two sets of tapered rotor blades. The baseline rotor blade set used a NACA 0012 airfoil section, whereas the second rotor blade set had advanced rotorcraft airfoils distributed along the radius. The experiment was conducted for a range of thrust coefficients and tip speeds, and the data were compared to the predictions of three analytical methods. The data show the advantage of the advanced airfoils at the higher rotor thrust levels; two of the analyses predicted the correct data trends.

Althoff, Susan L.↗

NASA NTRS1984

Hover test of a full-scale hingeless rotor

The performance and aeroelastic stability in hover of a 9.8-m diameter, hingeless helicopter rotor system was evaluated. Rotor performance and inplane damping data were obtained for rotor operation between 350 and 425 rpm for thrust coefficients (CT/sigma) between 0.0 and 0.12. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Good agreement is shown between experimental performance data and predicted performance. The influence of different aerodynamic inflow models on predicting damping levels is also shown. The best correlation with experimental stability data was obtained when a dynamic inflow model was used instead of static or quasistatic inflow models. Comparison with other full scale, hingeless rotor data in hover is presented. The hingeless rotor data and data from a full scale, bearingless main rotor test performed on the same general purpose test apparatus were compared. Although the bearingless rotor was more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown. At low thrust levels the bearingless main rotor is less damped than the hingeless rotor.

Warmbrodt, W.↗

NASA NTRS1984

Hover test of a full-scale hingeless rotor

The performance and aeroelastic stability in hover of a 9.8-m diameter, hingeless helicopter rotor system was evaluated. Rotor performance and inplane damping data were obtained for rotor operation beteen 350 and 425 rpm for thrust coefficients (CT/sigma) between 0.0 and 0.12. At constant rotor thrust, a minimum in rotor inplane damping was measured at 400 rpm. Good agreement is shown between experimental performance data and predicted performance. The influence of different aerodynamic inflow models on predicting damping levels is also shown. The best correlation with experimental stability data was obtained when a dynamic inflow model was used instead of static or quasistatic inflow models. Comparison with other full scale, hingeless rotor data in hover is presented. The hingeless rotor data and data from a full scale, bearingless main rotor test performed on the same general purpose test apparatus were compared. Although the bearingless rotor was more highly damped at design tip speed and 1-g thrust operation, greater sensitivity to operating conditions is shown. At low thrust levels the bearingless main rotor is less damped than the hingeless rotor.

Warmbrodt, W.↗

NASA NTRS1981

Experimental and analytical studies of a model helicopter rotor in hover

A benchmark test to aid the development of various rotor performance codes was conducted. Simultaneous blade pressure measurements and tip vortex surveys were made for a wide range of tip Mach numbers including the transonic flow regime. The measured tip vortex strength and geometry permit effective blade loading predictions when used as input to a prescribed wake lifting surface code. It is also shown that with proper inflow and boundary layer modeling, the supercritical flow regime can be accurately predicted.

Caradonna, F. X.↗

NASA NTRS1988

A comparison of theory and experiment for coupled rotor body stability of a bearingless rotor model in hover and forward flight

Seven cases were selected for correlation from a 1/5.86 Froude-scale experiment that examined several rotor designs which were being considered for full-scale flight testing as part of the Bearingless Main Rotor (BMR) program. The model rotor hub used in these tests consisted of back-to-back C-beams as flexbeam elements with a torque tube for pitch control. The first four cases selected from the experiment were hover tests which examined the effects on rotor stability of variations in hub-to-flexbeam coning, hub-to-flexbeam pitch, flexbeam-to-blade coning, and flexbeam-to-blade pitch. The final three cases were selected from the forward flight tests of optimum rotor configuration as defined during the hover test. The selected cases examined the effects of variations in forward speed, rotor speed, and shaft angle. Analytical results from Bell Helicopter Textron, Boeing Vertol, Sikorsky Aircraft, and the U.S. Army Aeromechanics Laboratory were compared with the data and the correlations ranged from poor-to-fair to fair-to-good.

Mirick, Paul H.↗

NASA NTRSDate not supplied

Acoustic and Performance Measurements Obtained in the NASA Langley Small Hover Anechoic Chamber

The emergence of small Unmanned Aircraft Systems (UAS) and Advanced Air Mobility (AAM) vehicles has motivated the need to acoustically characterize the rotors found on these vehicle platforms. Hover chamber tests of small rotors are beneficial in assessing the noise impact of UAS, and potentially larger AAM vehicles. Various experiments have been conducted in the NASA Langley Small Hover Anechoic Chamber (SHAC), formerly known as the Small Anechoic Jet Facility (SAJF), in order to investigate the noise and performance of small rotors. One of these tests was that of an “ideally twisted rotor”, which was designed in order to simplify the theoretical rotor inflow for a target thrust condition in hover. This rotor was fabricated using state-of-the-art rapid prototyping and tested in the SHAC. Aerodynamic load and acoustic data were acquired across a range of rotation rates and rotor collective settings. Both tonal and broadband components were identified in the acoustic data, with broadband noise being a prominent contributor to the overall rotor system noise.

Nicole Pettingill↗

NASA NTRS1994

Demonstration of an elastically coupled twist control concept for tilt rotor blade application

This study demonstrated the feasibility of passive blade twist control for composite rotor blades. Hover testing of the set of blades produced maximum twist changes of 2.54 degrees for the unballasted blade configuration and 5.24 degrees for the ballasted blade configuration. These results compared well with those obtained from a detailed finite element analysis model of the rotor blade, which yielded maximum twists of 3.02 and 5.61 degrees for the unballasted and ballasted blade configurations, respectively.

TILT ROTOR BLADE↗

NASA NTRS1978

Hovering impulsive noise: Some measured and calculated results

In-plane impulsive noise radiating from a hovering model rotor was measured in an anechoic environment. The hover acoustic signature was compared with existing theoretical prediction models with previous forward flight experiments using the same model rotor. These hover tests showed good experimental consistency with forward flight measurements, both in pressure level, and waveform character, over the range of Mach numbers tested (0.8 to 1.0). Generally poor correlation, however, was confirmed with current linear theory prediction efforts. Failure to predict both the peak pressure levels and the shape was reported, especially with increasing tip Mach number.

Boxwell, D. A.↗

NASA NTRS1976

Hover performance tests of full scale variable geometry rotors

Full scale whirl tests were conducted to determine the effects of interblade spatial relationships and pitch variations on the hover performance and acoustic signature of a 6-blade main rotor system. The variable geometry rotor (VGR) variations from the conventional baseline were accomplished by: (1) shifting the axial position of alternate blades by one chord-length to form two tip path planes; and (2) varying the relative azimuthal spacing from the upper rotor to the lagging hover rotor in four increments from 25.2 degrees to 62.1 degrees. For each of these four configurations, the differential collective pitch between upper and lower rotors was set at + or - 1 deg, 0 deg and -1 deg. Hover performance data for all configurations were acquired at blade tip Mach numbers of 0.523 and 0.45. Acoustic data were recorded at all test conditions, but analyzed only at 0 deg differential pitch at the higher rotor speed. The VGR configurations tested demonstrated improvements in thrust at constant power as high as 6 percent. Reductions of 3 PNdb in perceived noise level and of 4 db in blade passage frequency noise level were achieved at the higher thrust levels. Consistent correlation exists between performance and acoustic improvements. For any given azimuth spacing, performance was consistently better for the differential pitch condition of + or - 1 degree, i.e. with the upper rotor pitch one degree higher than the lower rotor.

Rorke, J. B.↗

NASA NTRS1981

Hover tests of a model H-force rotor

The potential of using tip vanes at the ends of helicopter rotor blades to obtain a controllable H-force is considered. The addition of vanes placed perpendicular to the blade tips can be used to obtain an inplane force. By varying the angle of the vanes, a radial force can be created which can be controllable in azimuth position. Such a force could be used to provide translational motion of the rotor and aircraft without the requirement for rotor tilting. In addition, an H-force generated at high flight speed could be used as a propulsive force in a matter similar to a propeller. The force generated by the vanes could also affect the aircraft's stability characteristics. The H-force could also modify rotor performance in hovering since they could be thought to act as a virtual shroud. Tests were run with a model rotor which has a 6 foot diameter with a 3 inch chord blade. Test data are presented on the effects of various tip-vane configurations on the hovering figure of merit. The extreme sensitivity of the performance to vane arrangement is shown.

Velkoff, H. R.↗

NASA NTRS1978

Experimental investigation of the subwing tip and its vortex structure

A better understanding of the subwing's vortex structure relative to a square tip for several angles of attack and yaw angles is provided. This comparison included subwings of various chord size and airfoil thickness. Flow visualization, together with performance and wake measurements, provided a comparison between the square tip and subwing tips during both a semi-span wind-tunnel test and a small-scale rotor hover-stand test.

Tangler, J. L.↗

NASA NTRS1985

Experimental study of main rotor tip geometry and tail rotor interactions in hover. Volume 2: Run log and tabulated data

A model scale hover test was conducted in the Sikorsky Aircraft Model Rotor hover Facility to identify and quantify the impact of the tail rotor on the demonstrated advantages of advanced geometry tip configurations. The existence of mutual interference between hovering main rotor and a tail rotor was acknowledged in the test. The test was conducted using the Basic Model Test Rig and two scaled main rotor systems, one representing a 1/5.727 scale UH-60A BLACK HAWK and the others a 1/4.71 scale S-76. Eight alternate rotor tip configurations were tested, 3 on the BLACK HAWK rotor and 6 on the S-76 rotor. Four of these tips were then selected for testing in close proximity to an operating tail rotor (operating in both tractor and pusher modes) to determine if the performance advantages that could be obtained from the use of advanced geometry tips in a main rotor only environment would still exist in the more complex flow field involving a tail rotor. This volume contains the test run log and tabulated data.

Balch, D. T.↗