SEARCH · Search NASA

Results for “Rotor Tip Vortices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRS1985

Wide-field shadowgraph flow visualization of tip vortices generated by a helicopter rotor

The vortex trajectory and vortex wake generated by helicopter rotors were visualized using a wide-field shadowgraph technique. Use of a retro-reflective Scotchlite screen made it possible to investigate the flow field generated by full-scale tail rotors. Tip vortex trajectories were visible in shadowgraphs for a range for tip Mach number of 0.38 - 0.60. The effect of the angle of attack was substantial. At an angle of attack greater than 8 degrees, the visibility of the vortex core was significant even at relatively low tip Mach numbers. The theoretical analysis of the visibility was carried out for a rotating blade. This analysis demonstrated that the visibility decreases with increasing dimensionless core radius (ro/c) and increases with increasing tip Mach number. Based on this investigation, it is concluded that the wide-field shadowgraph flow visualization technique should be feasible to study the flow field generated by a large main rotor in a wind tunnel and in an outdoor full-scale test stand. Of note is that the shadowgraph technique could easily be used with other on-going tests such as aerodynamic performance study, noise measurements, velocity measurements with LDV or hot-wire anemometer, local pressure measurement on the rotor surface, etc.

Parthasarathy, S. P.↗

NASA NTRS1971

Investigation of rotor blade tip-vortex aerodynamics

Several aspects of the aerodynamics of rotor blade tip vortices are examined. Two particular categories are dealt with; (1) dynamic loads on a blade passing close to or intersecting a trailing vortex, and (2) the response of the trailing vortex core to changes in the flow. Results for both categories are in reasonable agreement with existing data, although lower pressure gradients were obtained than anticipated for category one. A correlation between trailing edge sweep angle at the tip and vortex core size was noted for category two.

Lewellen, W. S.↗

NASA NTRS1980

Comparison of calculated and measured helicopter rotor lateral flapping angles

Calculated and measured values of helicopter rotor flapping angles in forward flight are compared for a model rotor in a wind tunnel and an autogiro in gliding flight. The lateral flapping angles can be accurately predicted when a calculation of the nonuniform wake-induced velocity is used. At low advance ratios, it is also necessary to use a free wake geometry calculation. For the cases considered, the tip vortices in the rotor wake remain very close to the tip-path plane, so the calculated values of the flapping motion are sensitive to the fine details of the wake structure, specifically the viscous core radius of the tip vortices.

Johnson, W.↗

NASA NTRS1989

Laser velocimeter measurements of the flowfield generated by an advanced counterrotating propeller

Results are presented of an investigation to measure the flowfield generated by an advanced counterrotating pusher propeller model similar to the full-scale Unducted Fan demonstrator engine. A laser Doppler velocimeter was used to measure the velocity field in several planes normal to the centerline of the model at axial stations upstream and downstream of each rotor. During this investigation, blades of the F4/A4 type were installed on the model which was operating in a freestream Mach 0.72 regime, with the advance ratio of each rotor set at 2.80. The measured data indicate only a slight influence of the potential field of each front rotor blade on the flowfield upstream of the rotor. The data measured downstream of the front rotor characterize the tip vortices, vortex sheets and potential field nonuniformities generated by the front rotor. The unsteadiness of the flow in the rotating frame of reference of the aft rotor is also illustrated.

Podboy, Gary G.↗

NASA NTRS1989

Laser velocimeter measurements of the flowfield generated by an advanced counterrotating propeller

Results are presented of an 0.72 regime, with the advance ratio of each rotor set at 2.80. The measured data indicate only a slight influence of the potential field of each front rotor blade on the flowfield upstream of the rotor. The data measured downstream of the front rotor characterize the tip vortices, vortex sheets and potential field nonuniformities generated by the front rotor. The unsteadiness of the flow in the rotating frame of reference of the aft rotor is also illustrated.

Podboy, Gary G.↗

NASA NTRS1998

Blade vortex interaction noise reduction techniques for a rotorcraft

An active control device for reducing blade-vortex interactions (BVI) noise generated by a rotorcraft, such as a helicopter, comprises a trailing edge flap located near the tip of each of the rotorcraft's rotor blades. The flap may be actuated in any conventional way, and is scheduled to be actuated to a deflected position during rotation of the rotor blade through predetermined regions of the rotor azimuth, and is further scheduled to be actuated to a retracted position through the remaining regions of the rotor azimuth. Through the careful azimuth-dependent deployment and retraction of the flap over the rotor disk, blade tip vortices which are the primary source for BVI noise are (a) made weaker and (b) pushed farther away from the rotor disk (that is, larger blade-vortex separation distances are achieved).

Charles, Bruce D.↗

NASA NTRS1996

Blade vortex interaction noise reduction techniques for a rotorcraft

Charles, Bruce D.↗

NASA NTRS1977

Interaction of rotor tip flow irregularities with stator vanes as a noise source

The role of the interaction of rotor tip flow irregularities (vortices and velocity defects) with downstream stator vanes is discussed as a possible fan noise mechanism. This is accomplished by: indicating some of the methods of formation of these flow irregularities; observing how they would behave with respect to known noise behavior and; attempting to compare the strength of the rotor tip flow irregularity mechanism with the strength of the more common rotor wake-stator mechanism. The rotor tip flow irregularity-stator interaction is indicated as being a probable inflight noise source.

Dittmar, J. H.↗

NASA NTRS1984

Fan noise reduction achieved by removing tip flow irregularities behind the rotor - forward arc test configurations

The noise source caused by the interaction of the rotor tip flow irregularities (vortices and velocity defects) with the downstream stator vanes was studied. Fan flow was removed behind a 0.508 meter (20 in.) diameter model turbofan through an outer wall slot between the rotor and stator. Noise measurements were made with far-field microphones positioned in an arc about the fan inlet and with a pressure transducer in the duct behind the stator. Little tone noise reduction was observed in the forward arc during flow removal; possibly because the rotor-stator interaction noise did not propagate upstream through the rotor. Noise reductions were maded in the duct behind the stator and the largest decrease occurred with the first increment of flow removal. This result indicates that the rotor tip flow irregularity-stator interaction is as important a noise producing mechanism as the normally considered rotor wake-stator interaction.

Dittmar, J. H.↗

NASA NTRS1977

Interaction of rotor tip flow irregularities with stator vanes as a noise source

The role of the interaction of rotor tip flow irregularities (vortices and velocity defects) with downstream stator vanes is discussed as a possible fan noise mechanism. This is accomplished by: (1) indicating some of the mothods of formation of these flow irregularities; (2) observing how they would behave with respect to known noise behavior; and (3) attempting to compare the strength of the rotor tip flow irregularity mechanism with the strength of the more common rotor wake-stator mechanism. The rotor tip flow irregularity-stator interaction is indicated as being a probable inflight noise source.

Dittmar, J. H.↗

NASA NTRS2017

Navier-Stokes Simulation of UH-60A Rotor/Wake Interaction Using Adaptive Mesh Refinement

High-resolution simulations of rotor/vortex-wake interaction for a UH60-A rotor under BVI and dynamic stallconditions were carried out with the OVERFLOW Navier-Stokes code.a. The normal force and pitching moment variation with azimuth angle were in good overall agreementwith flight-test data, similar to other CFD results reported in the literature.b. The wake-grid resolution did not have a significant effect on the rotor-blade airloads. This surprisingresult indicates that a wake grid spacing of (Delta)S=10% ctip is sufficient for engineering airloads predictionfor hover and forward flight. This assumes high-resolution body grids, high-order spatial accuracy, anda hybrid RANS/DDES turbulence model.c. Three-dimensional dynamic stall was found to occur due the presence of blade-tip vortices passing overa rotor blade on the retreating side. This changed the local airfoil angle of attack, causing stall, unlikethe 2D perspective of pure pitch oscillation of the local airfoil section.

CFD Validation↗

NASA NTRS1989

Tip vortex geometry of a hovering helicopter rotor in ground effect

The wide-field shadowgraph method has been used to photograph the tip vortices of a hovering helicopter rotor in ground effect. The shadowgraphs were used to obtain quantitative measurements of the rotor tip vortex geometry both in and out of ground effect. Many important phenomena are visible in the rotor wake using this method. These include the variation in descent and contraction rates of the tip vortices in ground effect, and the interaction between tip vortices in the far wake. The tip vortex geometry from the shadowgraphs is compared with the tip vortex geometry predicted using a free wake hover performance analysis. The free wake analysis accurately predicts the tip vortex geometry both in and out of ground effect. Performance data from the test is compared with the performance predicted using several methods, including the free wake analysis. All methods provided reasonable predictions for the helicopter performance in ground effect.

Light, Jeffrey S.↗

NASA NTRS1991

The application of experimental data to blade wake interaction noise prediction

Blade wake interaction noise (BWI) has been defined as the broadband noise generated by the ingestion of turbulent trailing tip vortices by helicopter rotors. This has been shown to be the dominant contributor to the subjectively important part of the acoustic spectrum for the approach stage of a helicopter flyover. A prediction method for BWI noise based on the calculated trailing vortex trajectories has been developed and estimates of the vortex turbulence have been made. These measurements were made on a trailing vortex from a split wing arrangement and did not give the spectrum of the velocity fluctuations. A recent experiment carried out to measure the turbulence associated with a trailing vortex and the application of the results to BWI noise prediction is described.

Glegg, Stewart A. L.↗

NASA NTRS2015

Investigation of Unsteady Flow Interaction Between an Ultra-Compact Inlet and a Transonic Fan

In the present study, unsteady flow interaction between an ultra-compact inlet and a transonic fan stage is investigated. Future combat aircraft require ultra-compact inlet ducts as part of an integrated, advanced propulsion system to improve air vehicle capability and effectiveness to meet future mission needs. The main purpose of the study is to advance the current understanding of the flow interaction between two different ultra-compact inlets and a transonic fan for future design applications. Both URANS and LES approaches are used to calculate the unsteady flow field and are compared with the available measured data. The present study indicates that stall inception is mildly affected by the distortion pattern generated by the inlet with the current test set-up. The numerical study indicates that the inlet distortion pattern decays significantly before it reaches the fan face for the current configuration. Numerical results with a shorter distance between the inlet and fan show that counter-rotating vortices near the rotor tip due to the serpentine diffuser affects fan characteristics significantly.

Inlet↗

NASA NTRS2016

Tracking Blade Tip Vortices for Numerical Flow Simulations of Hovering Rotorcraft

Blade tip vortices generated by a helicopter rotor blade are a major source of rotor noise and airframe vibration. This occurs when a vortex passes closely by, and interacts with, a rotor blade. The accurate prediction of Blade Vortex Interaction (BVI) continues to be a challenge for Computational Fluid Dynamics (CFD). Though considerable research has been devoted to BVI noise reduction and experimental techniques for measuring the blade tip vortices in a wind tunnel, there are only a handful of post-processing tools available for extracting vortex core lines from CFD simulation data. In order to calculate the vortex core radius, most of these tools require the user to manually select a vortex core to perform the calculation. Furthermore, none of them provide the capability to track the growth of a vortex core, which is a measure of how quickly the vortex diffuses over time. This paper introduces an automated approach for tracking the core growth of a blade tip vortex from CFD simulations of rotorcraft in hover. The proposed approach offers an effective method for the quantification and visualization of blade tip vortices in helicopter rotor wakes. Keywords: vortex core, feature extraction, CFD, numerical flow visualization

Numerical↗

NASA NTRS2008

Vortex control for rotor blade devices

To control vortices originating at the tips of a rotor's blades rotating through the air at a revolution frequency f, separation control device(s) are actuated to periodically introduce perturbations into the airflow moving over the blades. The periodic introduction of perturbations is controlled in accordance with a periodic modulating frequency of introduction f.sub.0 while the frequency of the perturbations so-introduced is designated as f.sub.e. Vortex control is achieved when the periodic modulating frequency of introduction f.sub.0 satisfies the relationship nf.ltoreq.f.sub.0.ltoreq.f.sub.e where n is the number of blades.

Greenblatt, David↗

NASA NTRS2013

Measurements of Tip Vortices from a Full-Scale UH-60A Rotor by Retro- Reflective Background Oriented Schlieren and Stereo Photogrammetry

Positions of vortices shed by a full-scale UH-60A rotor in forward flight were measured during a test in the National Full- Scale Aerodynamics Complex at NASA Ames Research Center. Vortices in a region near the tip of the advancing blade were visualized from two directions by Retro-Reflective Background-Oriented Schlieren (RBOS). Correspondence of points on the vortex in the RBOS images from both cameras was established using epipolar geometry. The object-space coordinates of the vortices were then calculated from the image-plane coordinates using stereo photogrammetry. One vortex from the tip of the blade that had most recently passed was visible in most of the data. The visibility of the vortices was greatest at high thrust and low advance ratios. At these favorable conditions, vortices from the most recent passages of all four blades were detected. The vortex positions were in good agreement with PIV data for a case where PIV measurements were also made. RBOS and photogrammetry provided measurements of the angle at which each vortex passed through the PIV plane.

Schairer, Edward↗

NASA NTRS2000

Preliminary Study of a Model Rotor in Descent

Within a program designed to develop experimental techniques for measuring the trajectory and structure of vortices trailing from the tips of rotor blades, the present preliminary study focuses on a method for quantifying the trajectory of the trailing vortex during descent flight conditions. This study also presents rotor loads and blade surface pressures for a range of tip-path plane angles and Mach numbers. Blade pressures near the leading edge and along the outer radius are compared with data obtained on the same model rotor, but in open jet facilities. A triangulation procedure based on two directable laser-light sheets, each containing an embedded reference, proved effective in defining the spatial coordinates of the trailing vortex. When interrogating a cross section of the flow that contains several trailing vortices, the greatest clarity was found to result when the flow is uniformly seeded. Surface pressure responses during blade-vortex interactions appeared equally sensitive near the leading edge and along the outer portion of the blade, but diminished rapidly as the distance along the blade chord increased. The pressure response was virtually independent of whether the tip-path plane angle was obtained through shaft tilt or cyclic pitch. Although the shape and frequency of the pressure perturbations on the advancing blade during blade-vortex interaction are similar to those obtained in open-jet facilities, the angle of the tip-path plane may need to be lower than the range covered in this study.

McAlister, K. W.↗