Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rotor Tips”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Rotor tip vortex geometry measurements using the wide-field shadowgraph technique

Rotor tip vortex geometry data have been acquired using the wide-field shadowgraph technique. Shadowgraphs were taken of the wakes of two model main-rotor systems in hover. These shadowgraphs provided detailed tip vortex trajectories from which axial and radial vortex coordinates were measured. Using these coordinates, prescribed-wake parameters were determined and input into a hover-performance prediction code. The resultant predictions were compared with experimental performance data to help assess the capabilities of this code. Another result of the experimental work was the development of a method to predict the visibility of rotor tip vortices on shadowgraphs. Using this method, the ability of the shadowgraph technique to visualize tip vortices in the rotor wake was quantified.

Norman, T. R.↗
NASA NTRS1981

Dynamic analysis of a free-tip rotor

The flag-lag-torsion flutter of a constant-lift rotor (CLR) and a free-tip rotor (FTR) has been investigated in hovering flight. The CLR blade consists of a finite number of strips pivotally mounted on the spar; torsional stiffness of the strips is attained through the elastic axis offset from the aerodynamic center. It is shown that, with a suitable combination of lag damper and negative pitch-flap coupling, it is possible to design a CLR blade that is free of aeroelastic instability with suitable airfoil selection. The FTR blade, which consists of an inboard section similar to that of a conventional blade and a small outboard section freely pitching on its spar, is also free of aeroelastic instability.

Chopra, I.↗
NASA NTRS1983

Aerodynamic effect of a honeycomb rotor tip shroud on a 50.8-centimeter-tip-diameter core turbine

A 50.8-cm-tip-diameter turbine equipped with a rotor tip shroud of hexagonal cell (or honeycomb) cross section has been tested in warm air (416 K) for a range of shroud coolant to primary flow rates. Test results were also obtained for the same turbine operated with a solid shroud for comparison. The results showed that the combined effect of the honeycomb shroud and the coolant flow was to cause a reduction of 2.8 points in efficiency at design speed, pressure ratio, and coolant flow rate. With the coolant system inactivated, the honeycomb shroud caused a decrease in efficiency of 2.3 points. These results and those obtained from a small reference turbine indicate that the dominant factor governing honeycomb tip shroud loss is the ratio of honeycomb depth to blade span. The loss results of the two shrouds could be correlated on this basis. The same honeycomb and coolant effects are expected to occur for the hot (2200 K) version of this turbine.

Moffitt, T. P.↗
NASA NTRS1985

Free-tip-rotor wind-tunnel test results

Seven controller mechanisms and several tip geometries were proposed and evaluated in the course of a free tip rotor development program which integrated those components into a model rotor system for wind tunnel testing. After a rigid whirl test was run to determine controller mechanism performance and structural integrity, a second whirl test was performed with a model rotor incorporating a selected controller design and a selected tip platform to determine the transient behavior of the tips in response to aerodynamic excitation. The results obtained demonstrate that a swept, tapered tip with a tension-torsion strap controller furnished satisfactory mechanical operation, achieved the specified output torque, possessed a low spring rate, and had fast and stable response to excitation.

Stroub, R. H.↗
NASA NTRS1977

Cold-air performance of a 12.766-centimeter-tip-diameter axial-flow cooled turbine. 3: Effect of rotor tip clearance on overall performance of a solid blade configuration

Two tip clearance configurations, one with a recess in the casing and the other with a reduced rotor blade height, were investigated at design equivalent speed over a range of tip clearance from about 2.0 to 5.0 percent of the stator blade height. The optimum configuration with a recess in the casing was the one where the rotor tip diameter was equal to the stator tip diameter (zero blade extension). For this configuration there was an approximate 1.5 percent decrease in total efficiency for an increase in tip clearance of 1 percent of stator blade height. For the reduced blade height configurations there was an approximate 2.0 percent decrease in total efficiency for an increase in tip clearance of 1 percent of stator blade height.

Haas, J. E.↗
NASA NTRS1987

Aeroelastic modeling of swept tip rotor blades using finite elements

A special finite element for the modeling of a swept tip rotor blade is derived. The swept tip blade undergoes moderate deflections in flap, lag and torsion. The nonlinear, partial differential equations of motion are discretized using a Galerkin finite element method. Tip sweep introduces flap-torsion and lag-axial couplings, and may lead to aeroelastic instabilities associated with frequency coalescence. When frequency coalescence does not occur, sweep is usually stabilizing. A comparison of the approximate model of a swept tip blade, using a blade with straight elastic axis and offsets of aerodynamic centers of gravity, with the exact swept tip model developed in this paper indicates that the approximate model can produce inaccurate results for the case of hingeless rotor blades.

Celi, R.↗
NASA NTRS2007

System and method for improved rotor tip performance

The present invention discloses systems and methods for the performance enhancement of rotary wing aircraft through reduced torque, noise and vibration. In one embodiment, a system includes a sail having an aerodynamic shape positioned proximate to a tip of the rotor blade. An actuator may be configured to rotate the sail relative to the blade tip. a A control system receives information from a rotorcraft system and commands the actuator to rotate the sail to a predetermined favorable rotor blade operating condition. In another embodiment, a method includes configuring the rotorcraft in a selected flight condition, communicating input signals to a control system operable to position sails coupled to tips of blades of a rotor assembly, processing the input signals according to a constraint condition to generate sail positional information, and transferring the sail positional information to the sail.

Bussom, Richard↗
NASA NTRS1983

An experimental investigation of a free-tip rotor configuration in a forward flight wind-tunnel test

Results from an experimental evaluation of a free-tip rotor are presented. The evaluation included whirl tests and wind tunnel tests up to advance ratios of 0.4. The free tip extended over the outer 5% of the rotor blade and included a passive mechanical controller whose output characteristics were varied. The controller configuration combined with the free tip aerodynamics resulted in higher power requirements, because the tip's pitch angle was 5 to 10 degrees greater than that of the inboard portion of the blade, and its pitching motion capability was considered to be inhibited by frictional forces. Recommendations are included for design features for a follow-on test.

Stroub, R. H.↗
NASA NTRS1989

Computational and experimental evaluation of helicopter rotor tips for high speed forward flight

A computational and experimental method for the evaluation of helicopter rotor tips in high-speed forward flight is presented which uses an unsteady full-potential solver on the advancing side of the rotor disk. Forces and moments measured during angle-of-attack sweeps reveal the soft-stall phenomenon of the double-swept planforms as well as the delayed stall of the single-swept hyperbolic tip. Double-swept planforms are shown to exhibit the most favorable performance, creating counter-rotating vortices that augment the lifting capabilities of the blade at high angles of attack and delay the onset of stall.

Sigl, Dave↗
NASA NTRS1977

Measurements of helicopter rotor tip vortices

This paper presents results from a recent wind-tunnel investigation of model helicopter rotor tip vortices. Measurements were made of the vortex positions, core sizes, and velocity distributions. A laser velocimeter was used to make the measurements, and a minicomputer-based data system was used to process the data and to aid in controlling the experiment. The velocimeter, the data system, and the software developed for the minicomputer are briefly described. The rotors investigated were two-bladed, teetering rotors with diameters of 2.1 m. Two sets of blades were used, one set with zero twist and one set with -11 deg of linear twist. The vortex positions were obtained by making flow field traverses while strobing the data system at a fixed azimuth. Aging of a vortex element was also studied by following the convected element while strobing the data system at different azimuths. By this method, the effects on the vortex of a close interaction with a blade and another vortex were studied.

Biggers, J. C.↗
NASA NTRS1986

The evaluation of a number of prototypes for the free-tip rotor constant-moment controller

The development of several prototypes of a constant moment controller, a critical component of the free-tip rotor (FTR) concept, is described. Also presented are the experimental results of a whirl test designed to select a final controller configuration to be included in a future wind-tunnel test of this innovative rotor system. A brief explanation of the FTR concept and its history are included. The paper documents the controller design constraints, each prototype's operating principle, the evaluation test, and the individual prototype test results. A recommended design is identified, along with the selection rationale.

Young, L. A.↗
NASA NTRS1989

Investigation of a free-tip rotor configuration for research on spanwise life distributions and wake velocity surveys of a semi-span wing with a discontinuous twist

A wind tunnel test was conducted in the NASA Ames 7 x 10 Foot Wind Tunnel to investigate the lift distribution on a semi-span wing with a discontinuous change in spanwise twist. The semi-span wing had a tip with an adjustable pitch angle independent on the inboard section pitch angle simulating the free-tip rotor blade when its free-tip is at a deflected position. The spanwise lift distribution over the wing and the tip were measured and three component velocity surveys behind the wing were obtained with a three dimensional laser Doppler velocimeter (LV) with the wing at one angle of attack and the tip deflected at different pitch angles. A six component internal strain gage balance was also used to measure total forces and moments on the tip. The three dimensional lift was computed from the two dimensional life distributions obtained from the LV and from the strain gage balance. The results from both experimental methods are shown to be in agreement with predictions made by a steady, three dimensional panel code, VSAERO.

Fortin, Paul↗
NASA NTRS2015

A Rotor Tip Vortex Tracing Algorithm for Image Post-Processing

A neurite tracing algorithm, originally developed for medical image processing, was used to trace the location of the rotor tip vortex in density gradient flow visualization images. The tracing algorithm was applied to several representative test images to form case studies. The accuracy of the tracing algorithm was compared to two current methods including a manual point and click method and a cross-correlation template method. It is shown that the neurite tracing algorithm can reduce the post-processing time to trace the vortex by a factor of 10 to 15 without compromising the accuracy of the tip vortex location compared to other methods presented in literature.

Overmeyer, Austin D.↗
NASA NTRS1956

Visualization of Rotor Tip Secondary Flows with Blade Tip Air Discharge and Suction in a Low-speed Turbine

Smoke was used to visualize outer-wall secondary flows in a low-speed turbine utilizing rotor tip air discharge and suction. Photographs as well as visual observations of the effect of tip air discharge and suction were made by independently varying the direction and quantity of the tip air discharge and suction, and varying tip clearance, and main-stream air speed. In addition, the cross-sectional area of the hollow blade discharge opening was varied for the case of tip air discharge.

Kofskey, Milton G↗
NASA NTRS1985

Transonic rotor tip design using numerical optimization

The aerodynamic design procedure for a new blade tip suitable for operation at transonic speeds is illustrated. For the first time, 3 dimensional numerical optimization was applied to rotor tip design, using the recent derivative of the ROT22 code, program R22OPT. Program R22OPT utilized an efficient quasi-Newton optimization algorithm. Multiple design objectives were specified. The delocalization of the shock wave was to be eliminated in forward flight for an advance ratio of 0.41 and a tip Mach number of 0.92 at psi = 90 deg. Simultaneously, it was sought to reduce torque requirements while maintaining effective restoring pitching moments. Only the outer 10 percent of the blade span was modified; the blade area was not to be reduced by more than 3 percent. The goal was to combine the advantages of both sweptback and sweptforward blade tips. A planform that featured inboard sweepback was combined with a sweptforward tip and a taper ratio of 0.5. Initially, the ROT22 code was used to find by trial and error a planform geometry which met the design goals. This configuration had an inboard section with a leading edge sweep of 20 deg and a tip section swept forward at 25 deg; in addition, the airfoils were modified.

Tauber, Michael E.↗
NASA NTRS1975

Two-stage fan. 3: Data and performance with rotor tip casing treatment, uniform and distorted inlet flows

A two stage fan with a 1st-stage rotor design tip speed of 1450 ft/sec, a design pressure ratio of 2.8, and corrected flow of 184.2 lbm/sec was tested with axial skewed slots in the casings over the tips of both rotors. The variable stagger stators were set in the nominal positions. Casing treatment improved stall margin by nine percentage points at 70 percent speed but decreased stall margin, efficiency, and flow by small amounts at design speed. Treatment improved first stage performance at low speed only and decreased second stage performance at all operating conditions. Casing treatment did not affect the stall line with tip radially distorted flow but improved stall margin with circumferentially distorted flow. Casing treatment increased the attenuation for both types of inlet flow distortion.

Burger, G. D.↗