Search NASA⌕ Search

SEARCH · Search NASA

Results for “SOLIDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Polycarbonate‐Based Solid‐Polymer Electrolytes for Solid‐State Sodium Batteries

Solid-polymer electrolytes comprised of polypropylene carbonate (PPC) and varied sodium bis(fluorosulfonyl)imide (NaFSI) salt concentrations are investigated for implementation as a conductive solid polymer electrolyte into solid-state cathode composites utilizing a sodium-layered oxide active material. The ionic conductivity generally increases with NaFSI salt content, reaching ≈1 mS cm −1 at 80 °C at the highest salt concentration (PPC:NaFSI = 0.5:1). Through an all-in-one slurry casting method, Na 2/3 Ni 1/3 Mn 2/3 O 2 cathode composites are fabricated in which the dispersed PPC electrolyte acts as the primary binder. Enabled by a bilayer polymer electrolyte system, cycling performance with the PPC cathode electrolyte is optimized with respect to salt concentration and anode material. The best cyclability is achieved with a moderate salt concentration electrolyte (PPC:NaFSI = 5:1), showcasing an initial capacity of 83 mA h g −1 with a remarkable 80% capacity retention after 150 cycles at C/5 rate and 60 °C. The superior performance of the lower salt concentration electrolyte is attributed to better electrochemical stability, as confirmed by linear sweep voltammetry and online electrochemical mass spectrometry measurements. In conclusion, these results underscore the potential of carbonate-based polymer electrolytes and the importance of balancing electrolyte conductivity and stability in cell design.

25 ENERGY STORAGE↗
NASA NTRS1963

PARTICIPATION OF THE SOLID PHASE IN THE OSCILLATORY BURNING OF SOLID ROCKET PROPELLANTS

An experimental study of the interaction between the solid and gas phases during oscillatory burning of solid propellants has been undertaken with the objective of exploring the validity of the complex theory describing the phenomenon. The apparatus employed was a side-vented, cylindrical vessel with an end-burning propellant grain closely fitted in one end and provision for maintaining the burning zone at a fixed position. Pressure oscillations both at the gas-zone end plate and beneath the grain were recorded. Energy dissipation in the solid propellant, isolated from other losses in the system, was determined from the growth rate constants of the amplitudes of pressure oscillation for grains of varying lengths. The efficiency of acoustical energy or absorption by the grain was found to be maximum when the oscillations are at frequencies close to the natural frequency of the grain. These results confirm the description of oscillatory burning by the acoustical theory in its broad generalizations.

GAS PHASE↗
DOE OSTI2024

A New Class of Oxyhalide Solid Electrolytes NaNbCl 6‐2x O x for Solid‐state Sodium Batteries

Abstract Sodium‐based batteries are gaining momentum due to the abundance and lower cost of sodium compared to lithium. Solid‐state sodium batteries can also provide further safety advantages. However, sodium‐based solid‐state electrolytes (SSEs) that meet all the rigorous requirements, such as high ionic conductivity, oxidative stability with the cathode, and ease of processability, are lacking. We present here a new class of sodium‐based oxyhalide electrolytes NaNbCl 6‐2x O x with a facile mechanochemical synthesis. The oxyhalide NaNbCl 4 O exhibits close to two orders of magnitude higher ambient‐temperature sodium‐ion conductivity (1.03×10 −4 S cm −1 ) compared to the halide counterpart NaNbCl 6 (3×10 −6 S cm −1 ). Structural motifs unique to the oxygen content in NaNbCl 6‐2x O x are identified with 23 Na and 93 Nb magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy and x‐ray diffraction (XRD). Solid‐state sodium batteries assembled with NaNbCl 4 O electrolyte and the cobalt‐ and nickel‐free layered Na 0.70 Fe 0.3 Mn 0.65 Al 0.05 O 2 cathode exhibit a maximum discharge capacity of 155 mAh g −1 with good cycle life at ambient temperature.

Kmiec, Steven↗
DOE OSTI2024

A New Class of Oxyhalide Solid Electrolytes NaNbCl 6‐2x O x for Solid‐state Sodium Batteries

Abstract Sodium‐based batteries are gaining momentum due to the abundance and lower cost of sodium compared to lithium. Solid‐state sodium batteries can also provide further safety advantages. However, sodium‐based solid‐state electrolytes (SSEs) that meet all the rigorous requirements, such as high ionic conductivity, oxidative stability with the cathode, and ease of processability, are lacking. We present here a new class of sodium‐based oxyhalide electrolytes NaNbCl 6‐2x O x with a facile mechanochemical synthesis. The oxyhalide NaNbCl 4 O exhibits close to two orders of magnitude higher ambient‐temperature sodium‐ion conductivity (1.03×10 −4 S cm −1 ) compared to the halide counterpart NaNbCl 6 (3×10 −6 S cm −1 ). Structural motifs unique to the oxygen content in NaNbCl 6‐2x O x are identified with 23 Na and 93 Nb magic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy and x‐ray diffraction (XRD). Solid‐state sodium batteries assembled with NaNbCl 4 O electrolyte and the cobalt‐ and nickel‐free layered Na 0.70 Fe 0.3 Mn 0.65 Al 0.05 O 2 cathode exhibit a maximum discharge capacity of 155 mAh g −1 with good cycle life at ambient temperature.

Kmiec, Steven↗
DOE OSTI2024

LaCl 3 -based sodium halide solid electrolytes with high ionic conductivity for all-solid-state batteries

To enable high performance of all solid-state batteries, a catholyte should demonstrate high ionic conductivity, good compressibility and oxidative stability. Here, a LaCl 3 -based Na + superionic conductor (Na 1–x Zr x La 1–x Cl 4 ) with high ionic conductivity of 2.9 × 10 –4 S cm –1 (30 °C), good compressibility and high oxidative potential (3.80 V vs. Na 2 Sn) is prepared via solid state reaction combining mechanochemical method. X-ray diffraction reveals a hexagonal structure (P6 3 /m) of Na 1–x Zr x La 1–x Cl 4 , with Na + ions forming a one-dimensional diffusion channel along the c-axis. First-principle calculations combining with X-ray absorption fine structure characterization etc. reveal that the ionic conductivity of Na 1–x Zr x La 1–x Cl 4 is mainly determined by the size of Na + -channels and the Na + /La 3+ mixing in the one-dimensional diffusion channels. When applied as a catholyte, the NaCrO 2 ||Na 0.7 Zr 0.3 La 0.7 Cl 4 ||Na 3 PS 4 ||Na 2 Sn all-solid-state batteries demonstrate an initial capacity of 114 mA h g –1 and 88% retention after 70 cycles at 0.3 C. In addition, a high capacity of 94 mA h g –1 can be maintained at 1 C current density.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Local order, disorder, and everything in between: using 91 Zr solid-state NMR spectroscopy to probe zirconium-based metal–organic frameworks

Characterization of metal centers in metal–organic frameworks (MOFs) is critical for rational design and further understanding of structure–property relationships. The short-range structure about Zr atoms is challenging to properly elucidate in many Zr MOFs, particularly when local disorder is present. Static 91 Zr solid-state NMR spectra of the seven zirconium MOFs UiO-66, UiO-66-NH 2 , UiO-67, MOF-801, MOF-808, DUT-68 and DUT-69 have been acquired at high magnetic fields of 35.2 T and 19.6 T, yielding valuable information on the local structure, site symmetry and order about Zr. 91 Zr NMR is very sensitive to differences in MOF short-range structure caused by guest molecules, linker substitution and post-synthetic treatment. Complementary density functional theory (DFT) calculations assist in the interpretation and assignment of 91 Zr solid-state NMR spectra, lend insight into structural origins of 91 Zr NMR parameters and enable determination of local Zr coordination environments. This approach can be extended to many other materials containing zirconium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2000

Preparation of Ion Exchange Films for Solid-Phase Spectrophotometry and Solid-Phase Fluorometry

Atomic spectroscopy has dominated the field of trace inorganic analysis because of its high sensitivity and selectivity. The advantages gained by the atomic spectroscopies come with the disadvantage of expensive and often complicated instrumentation. Solid-phase spectroscopy, in which the analyte is preconcentrated on a solid medium followed by conventional spectrophotometry or fluorometry, requires less expensive instrumentation and has considerable sensitivity and selectivity. The sensitivity gains come from preconcentration and the use of chromophore (or fluorophore) developers and the selectivity is achieved by use of ion exchange conditions that favor the analyte in combination with speciative chromophores. Little work has been done to optimize the ion exchange medium (IEM) associated with these techniques. In this report we present a method for making ion exchange polymer films, which considerably simplify the solid-phase spectroscopic techniques. The polymer consists of formaldehyde-crosslinked polyvinyl alcohol with polyacrylic acid entrapped therein. The films are a carboxylate weak cation exchanger in the calcium form. They are mechanically sturdy and optically transparent in the ultraviolet and visible portion of the spectrum, which makes them suitable for spectrophotometry and fluorometry.

Hill, Carol M.↗
DOE OSTI2025

Voltage cycling as a dynamic operation mode for high temperature electrolysis solid oxide cells

Solid Oxide Electrolysis Cells (SOECs) have emerged as a promising technology for the efficient production of H2 via high-temperature electrolysis. However, power input from dynamic energy sources remains a significant challenge for their long-term stability. It is important to analyze the tolerance of cells under dynamic operation conditions. This study focuses on evaluating the impact of voltage cycling on the performance and durability of electrode-supported SOECs. We explore the operational limits and degradation mechanisms of SOECs subjected to various voltage conditions and find that the cells have high tolerance for dynamic voltage. Voltage cycling between 1.3 V and 1.5 V for 9000 cycles does not damage the cell. Conversely, cycling to higher voltages (≥1.7 V) results in accelerated degradation. Advanced characterization is used to screen for various degradation modes post operation. Within the oxygen electrode, XRD and STEM EDS find compositional and phase evolution in all voltage cycled samples including increased decomposition of the air electrode resulting in cation migration. Microstructural analysis of the fuel electrode from nano-CT data shows minimal change throughout the sample set and no evidence of Ni migration, indicating the fuel electrode is stable and not impacted by cycling to higher voltages within the timeframe studied.

Zhu, Zhikuan↗
DOE OSTI2025

Advances in solid-state NMR for the studies of mesoporous solids: fast magic spinning and dynamic nuclear polarization

Here, this review provides an up-to-date account of the development of two solid-state (SS)NMR methods for enhancing resolution and sensitivity, fast magic angle spinning (MAS) and dynamic nuclear polarization (DNP), and the resulting progress in surface science. We demonstrate the high resolution and efficiency that can be achieved by using two-dimensional homo- and heteronuclear correlation experiments with small rotors capable of MAS at rates exceeding 100 kHz. DNP has offered significant enhancements in signal sensitivity and allowed access to nuclei and experiments that are beyond the limits of conventional SSNMR. The continuing progress in fast MAS and DNP methodologies in recent years generated an unprecedented shift in SSNMR’s capabilities in the studies of surface and interface regions of solids, especially mesoporous supports and catalysts. We give numerous examples of recent applications and discuss the prospects for further improvements of both methods.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

A Sulfide‐Based Solid Electrolyte With High Humid Air Tolerance for Long Lifespan All‐Solid‐State Sodium Batteries

Abstract Sulfide‐based superionic conductors present great promise to achieve high energy density and safety for all‐solid‐state sodium batteries (ASSSBs). However, the poor electrolyte/electrode interface compatibility and humid air stability seriously hinder their deployment in ASSSBs. Herein, a series of high‐performance Na 3‐□ Sb 1‐4x (SnWCaTi) x S 4 sulfide‐based solid electrolytes (SSEs) are reported by coupling the vacancy effect with configurational entropy, which displays an excellent interface stability against sodium metal and an extraordinary tolerance toward the moist atmosphere, even for water. The optimized electrolyte effectively inhibits the detrimental mixed ion‐electron conducting interphase formation, achieving the ultra‐stable operation of Na–Na symmetric cell up to 1000 h. Furthermore, the Na + diffusion kinetics is obviously enhanced by increasing the Na sites local anisotropy and Na vacancies. Eventually, the assembled TiS 2 //Na 5 Sn ASSSBs deliver a remarkable reversible capacity of 211.6 mAh g −1 at 0.5C with a long‐term cycling performance of 450 cycles at room temperature. More importantly, it achieves a steady running up to 100 cycles at 1C even if this electrolyte is placed in the air with a dew temperature of 13.8 °C for 30 min, the highest values in the state‐of‐the‐art sulfide‐based ASSSBs. The well‐designed SSEs open a new avenue for realizing the advanced and powerful ASSSBs.

Guo, Yayu↗
DOE OSTI2023

High‐Entropy Lithium Argyrodite Solid Electrolytes Enabling Stable All‐Solid‐State Batteries

Abstract Superionic solid electrolytes (SEs) are essential for bulk‐type solid‐state battery (SSB) applications. Multicomponent SEs are recently attracting attention for their favorable charge‐transport properties, however a thorough understanding of how configurational entropy (ΔS conf ) affects ionic conductivity is lacking. Here, we successfully synthesized a series of halogen‐rich lithium argyrodites with the general formula Li 5.5 PS 4.5 Cl x Br 1.5‐x (0≤x≤1.5). Using neutron powder diffraction and 31 P magic‐angle spinning nuclear magnetic resonance spectroscopy, the S 2− /Cl − /Br − occupancy on the anion sublattice was quantitatively analyzed. We show that disorder positively affects Li‐ion dynamics, leading to a room‐temperature ionic conductivity of 22.7 mS cm −1 (9.6 mS cm −1 in cold‐pressed state) for Li 5.5 PS 4.5 Cl 0.8 Br 0.7 (ΔS conf =1.98R). To the best of our knowledge, this is the first experimental evidence that configurational entropy of the anion sublattice correlates with ion mobility. Our results indicate the possibility of improving ionic conductivity in ceramic ion conductors by tailoring the degree of compositional complexity. Moreover, the Li 5.5 PS 4.5 Cl 0.8 Br 0.7 SE allowed for stable cycling of single‐crystal LiNi 0.9 Co 0.06 Mn 0.04 O 2 (s‐NCM90) composite cathodes in SSB cells, emphasizing that dual‐substituted lithium argyrodites hold great promise in enabling high‐performance electrochemical energy storage.

Chemistry↗
DOE OSTI2025

Accelerating Discovery of Solid‐State Thin‐Film Metal Dealloying for 3D Nanoarchitecture Materials Design through Laser Thermal Gradient Treatment

Thin‐film solid‐state metal dealloying (thin‐film SSMD) is a promising method for fabricating nanostructures with controlled morphology and efficiency, offering advantages over conventional bulk materials processing methods for integration into practical applications. Although machine learning (ML) has facilitated the design of dealloying systems, the selection of key thermal treatment parameters for nanostructure formation remains largely unknown and dependent on experimental trial and error. To overcome this challenge, a workflow enabling high‐throughput characterization of thermal treatment parameters is demonstrated using a laser‐based thermal treatment to create temperature gradients on single thin‐film samples of Nb‐Al/Sc and Nb‐Al/Cu. This continuous thermal space enables observation of dealloying transitions and the resulting nanostructures of interest. Through synchrotron X‐ray multimodal and high‐throughput characterization, critical transitions and nanostructures can be rapidly captured and subsequently verified using electron microscopy. The key temperatures driving chemical reactions and morphological evolutions are clearly identified. While the oxidation may influence nanostructure formation during thin‐film treatment, the dealloying process at the dealloying front involves interactions solely between the dealloying elements, highlighting the availability and viability of the selected systems. Further, this approach enables efficient exploration of the dealloying process and validation of ML predictions, thereby accelerating the discovery of thin‐film SSMD systems with targeted nanostructures.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A bioinspired approach for adaptive solid-solid phase change material coatings with optimized surface features for passive thermal regulation

The necessity to reduce global energy consumption calls for innovative strategies in building thermal management. Passive thermal regulation, particularly through bio-inspired designs, offers a promising avenue by mimicking nature's efficient control of optical properties. This research introduces a novel, climate-responsive coating that integrates optimized bio-inspired surface features with a solid-solid phase change material (SS-PCM) to dynamically manage solar absorptivity without adding additional thickness, enabling both heating and cooling as needed. Drawing on the photonic architectures of the Saharan silver ant and Morpho Didius butterfly, we employed a modeling and multi-objective optimization framework to tailor these surface features. Simulations reveal that surface texture, rather than the intrinsic phase transition of the SS PCM, dominates optical control. Relative to a flat SS PCM coating, optimized isotropic random roughness and broader range features yielded the highest passive heating power increase of about 144 % and 319 % respectively suitable for cold climates. Saharan ant-inspired features enhanced passive cooling for hot climates, achieving a 21.8 % improvement. For moderate climates, Butterfly-wing-inspired surface features provided a balanced enhancement of 19 % for heating and 7 % for cooling. Across all cases, the optimized surface features reduced combined heating and cooling energy demand more effectively than the baseline coating, while preserving material thickness. These findings demonstrate that climate-adaptive, optimized bio-inspired surface features can unlock the full potential of SS PCM coatings, providing a versatile pathway to significant energy savings in buildings and other applications. The methodology establishes a framework for designing next-generation adaptive envelopes that leverage natural photonic principles for high-impact, low-cost thermal regulation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impact of Sr-Containing Secondary Phases on Oxide Conductivity in Solid-Oxide Electrolyzer Cells

Solid-oxide electrolyzer cells (SOECs) based on a yttria-stabilized zirconia (YSZ) oxide electrolyte produce hydrogen from water with the assistance of excess thermal energy; however, Sr diffusion within the Gd-doped CeO 2 (GDC) barrier layer during processing or operation can lead to the formation of unwanted secondary phases such as SrO and SrZrO 3 . Here, to establish and compare the degree of impact of these phases on SOEC performance, we conduct first-principles calculations to study their bulk oxide conductivities and compare them to that of the YSZ electrolyte. We find that SrO has a low conductivity arising from the poor mobility and low concentration of mobile oxygen vacancies, and its presence in SOECs should therefore be avoided. SrZrO 3 also has a lower oxide conductivity than YSZ; however, this discrepancy is primarily due to lower vacancy concentrations rather than low mobility. We find that sufficient levels of Y-doping on the Zr site can increase oxygen vacancy concentrations in SrZrO 3 to achieve an oxide ionic conductivity on par with that of YSZ, thereby mitigating any potential deleterious effect on transport performance. Energy-dispersive X-ray spectroscopy confirms that Y is the most common minority element present in SrZrO 3 forming near the GDC–YSZ interface, alleviating concerns regarding the impact of SrZrO 3 on device performance. These results from our combined computational–experimental analysis can inform future engineering strategies designed to limit the detrimental effects of Sr-induced secondary phase formation on SOEC performance.

08 HYDROGEN↗