An experimental and analytical study on the development of extrapolation method for the creep-fatigue life of Alloy 617 to low strain ranges and long hold times at 950°C
Explore the source record for details and available documents.
Hou, Peijun↗
SEARCH · Search NASA
Results for “STRAIN FATIGUE”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Physics-based Multiscale Additively Manufactured Superalloy Design for Optimized High Cycle Fatigue Life (Final Report)
The objectives of this project are to: (i) Gain fundamental understandings towards the microscopic damage mechanisms, as impacted by pertinent materials properties (e.g. stacking fault energy (SFE) and microstructure (e.g., grain size), leading to high-cycle fatigue (HCF) damage to AM Ni-based superalloy parts; (ii) Provide scientific insight into the effect of testing frequency on damage mechanisms and fatigue life of AM Ni-based superalloy parts under HCF regime, thereby establishing an appropriate correlation between accelerated testing and materials’ true service life; (iii) Devise an accurate, experimentally validated multiscale model across atomic, micro- and meso-scales, to predict the cyclic stress-strain responses and fatigue damage accumulation for AM Ni-based superalloys under various loading frequencies.
36 MATERIALS SCIENCE↗
Assessment of frequency and amplitude dependence on the cyclic degradation of polyurethane foams
Many energy absorption applications utilize flexible polymeric foams for their viscoelastic properties. It is desired that the material will perform consistently across repeated compression cycles. This study examines the effect of fatigue at low strain rates on the viscoelasticity of open-cell polyurethane foam. Six polyurethanes of the same base composition with two porosities (70% and 80%) and three chemical indexes (79i, 100i, and 121i) are tested. Large deformation cyclic compression of the foams is conducted on a universal testing system (UTS). These data are then post-processed leveraging dynamic mechanical analysis Fourier transform rheology to characterize changes in the viscoelasticity of the materials over fatigue cycles. Results show that foams can increase or decrease in stiffness up to 10% over 10 4 cycles. Specifically, higher chemical index, higher excitation frequency, and larger excitation amplitude correlate with a more pronounced decrease in stiffness. Damping can also change by 15% and correlates with chemical index and excitation frequency. Consequently, the findings suggest that internal foam structure and bulk material properties as well as applied loading parameters affect the viscoelastic fatigue response of flexible polymeric foams.
36 MATERIALS SCIENCE↗
Elastic interaction-induced anisotropic growth of dislocation loop arrays
The elastic interactions and reactions of dislocations lead to the formation of complex dislocation substructures, which is critical to the strain hardening and fatigue failure. Phase field dislocation dynamics simulations are conducted as a first step to understand the elastic interactions between dislocation loops. When the interloop spacing is small, the elastic interactions with neighboring loops become strong, rendering the edge segments strongly pinned, while allowing for the screw segments to propagate more easily. The interactions are found to result in an anisotropic stress distribution around the dislocation loops, leading to the formation of arrays of long, straight edge dislocations that could act as barriers to subsequent slip. Furthermore, the effect of initial loop size and applied strain rate on the elastic interaction-induced anisotropic pinning effect is investigated and discussed. Furthermore, the results are important for coarse-graining dislocation substructures formation into continuum level models of deformation in crystalline solids.
36 MATERIALS SCIENCE↗
An investigation into the effects of cyclic strain rate on the high cycle and very high cycle fatigue behaviors of wrought and additively manufactured Inconel 718
Additive Manufacturing (AM) has increasingly been used to fabricate parts in aerospace applications, which may require service lives beyond ten-million cycles due to the imposed high loading frequencies. Understanding the very high cycle fatigue (VHCF) behavior of these additive manufactured (AM) parts is an important step towards their design and qualification processes. This study focuses on the high cycle fatigue (HCF) and VHCF behaviors of both wrought and laser beam-powder bed fusion (LB-PBF) fabricated Inconel 718 in machined/polished surface condition, emphasizing on the influence of test frequency (i.e., cyclic strain rate). Uniaxial, fully-reversed force- and stress-controlled fatigue tests were conducted utilizing a servo-hydraulic and an ultrasonic test system operating at 5 Hz and 20 kHz, respectively, on wrought as well as LB-PBF vertically and diagonally built specimens. Fatigue cracks in the majority of the specimens were found to initiate from intra-granular slip bands near or at the surface, which gives rise to strong anisotropy in fatigue resistance in LB-PBF specimens due to the presence of columnar grains along the build directions. Longer fatigue lives were obtained at 20 kHz, which was ascribed to possibly lower-than-intended stresses applied in the ultrasonic tests. The corrected stress-life fatigue data at 20 kHz were found to converge to the one obtained from conventional testing at 5 Hz, implying no effect of cyclic strain rate on the fatigue behavior of Inconel 718 regardless of the fabrication process. The findings of this work confirm the use of ultrasonic fatigue testing to expedite generation of AM materials data to keep up with the current demand; however, the applied stress may need to be corrected.
36 MATERIALS SCIENCE↗
Hydrogen influences thermal activation parameters for dislocation glide during low cycle fatigue of 316L stainless steel
Measurements of activation areas are used to investigate the effect of hydrogen on the kinetics of dislocation glide during cyclic deformation in cold-worked 316L stainless steel. Non-charged and hydrogen-precharged (H-precharged) specimens were tested in low cycle fatigue (LCF) under plastic strain control. A series of plastic strain rate changes was performed periodically at the peak true plastic strain from the first cycle to half-life, and at various plastic strain values around stable hysteresis loops near half-life to determine the operational activation area, Δ a ∗. Both material conditions demonstrate a rapid increase in Δ a ∗ during the initial rapid softening followed by a region of approximately constant values coinciding with a reduced rate of softening. Near half-life, hydrogen reduces Δ a ∗ at a given true stress due to its effect on the activation distance and obstacle spacing. The magnitudes of Δ a ∗ reveal that bypassing solutes, cutting forest dislocations, and initiating cross slip are important mechanisms of thermally activated dislocation glide at all amplitudes, except hydrogen suppresses cross slip at the lowest plastic strain amplitudes. These results are supported by electron microscopy characterization of deformed microstructures. A Haasen plot analysis indicates that forest dislocations control the kinetics of deformation in both material conditions. It also reveals the presence of athermal obstacles in both non-charged and H-precharged conditions, likely dense dislocation tangles and cell walls. Additionally, the effect of hydrogen on microstructure evolution (by reducing the propensity for cross slip) leads to a dependence of athermal stress on plastic strain amplitude.
Activation area↗
Report on FY 2021 testing in support of integrating Alloy 800H and 2.25Cr-1Mo for EPP analysis
The use of simplified Elastic-Perfectly Plastic (EPP) design methods avoids the complexities and limitations of the elastic analysis approach in evaluating strain limits and creep-fatigue damage for Class A metallic coolant boundary components in ASME Boiler and Pressure Vessel Code, Section III, Division 5, Subsection HB, Subpart B. No stress classification and linearization are required in the EPP methods. Further, the strain limits and creep-fatigue damage evaluation procedures based on elastic analysis results were developed for the reactor operating conditions where uncoupled, rate-independent plasticity and stationary creep can be used to approximate the deformation in the component adequately. But at very high temperatures, the deformation is rate-dependent, and it can only be approximated adequately by unified viscoplastic model. Thus, for example, the elastic analysis approach cannot be used to evaluate strain limits and creep-fatigue damage for Alloy 617 above 650 °C. The EPP methods remove the temperature restriction. They can be used to evaluate strain limits and creep-fatigue damage for the full range of temperatures.
22 GENERAL STUDIES OF NUCLEAR REACTORS↗
Summary of FY2024 Experimental Results to Support Development of New Inelastic Material Models and Validation of Section III, Division 5, Class A Design Rules
To address the data gap crucial for updating existing viscoplastic constitutive material models for the Class A materials in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors (ASME, 2023) for inelastic design analysis, Oak Ridge National Laboratory (ORNL) conducted experimental studies on Alloy 800H and Alloy 617 across a range of temperatures up to their maximum temperature limits in Section III, Division 5. The studies aim to characterize the materials' deformation behavior under both strain-controlled mechanical cyclic loading and thermal cycling conditions. This report summarizes ORNL's FY 2024 experimental findings on Alloy 800H and Alloy 617, focusing on pure fatigue tests, cyclic stress-strain curves, thermomechanical fatigue experiments, and verification of the high temperature cyclic damage summation design rules.
36 MATERIALS SCIENCE↗
Role of deformation twinning in fatigue of CrCoNi medium-entropy alloy at room temperature
Here cylindrical specimens of CrCoNi alloy with electropolished surfaces were subjected to constant total strain amplitude low cycle fatigue. The alloy exhibited an initial period of cyclic hardening followed by cyclic softening until failure occurred. At the end of hardening stage at the peak of cyclic stress, well-developed persistent slip markings (PSMs) consisting of extrusions and intrusions were associated with thin deformation twins. A sophisticated experimental workflow was designed to extract information from the surface and the bulk of tested material. A combination of SEM, EBSD, ECCI, FIB and HR-STEM was used to study the internal structure and the surface profiles around the deformation twins, which were produced during the initial period of cyclic loading. Furthermore, localized cyclic plastic strain and stress concentrations near deformation twins led not only to early, well-developed PSMs, but also to the activation of TWIP and TRIP plasticity even at low macroscopic stress amplitudes.
36 MATERIALS SCIENCE↗
An extrapolation method for strain ranges and hold times in developing the EPP+SMT creep-fatigue design curves for Alloy 617
Experimental and numerical studies in developing the integrated Elastic–Perfectly Plastic (EPP) plus Simplified Model Test (SMT) design methodology, referred to as the EPP+SMT method, continued in FY2022. This report focuses on the methods for extrapolating the EPP+SMT creep-fatigue (CF) design curves at long hold times and low strain ranges. In this study, the available CF failure data on Alloy 617 at 950°C were analyzed to determine a set of CF failure criteria. At very low strain ranges and long hold times, CF failure data are not accessible by experiments because of the extraordinarily long test durations and the inability of the test machines to accurately control these small strain ranges. A CF experimental approach with the concept of block-strain range CF testing protocol was developed. Tests using this protocol were conducted to generate the needed information for calibrating material parameters of the numerical material models. The Time Fraction based method and Dissipated Energy method were used to extrapolate the CF life curves to low strain ranges and long hold times. Based on the new experimental approach and CF life prediction methods, the CF life curves with various hold times were developed for Alloy 617 at 950°C. In addition, an experiment was designed and is being performed to verify the predicted CF curves at 950°C. The extrapolation procedure will be applied at lower temperatures to complete the development of the EPP+SMT CF design curves for Alloy 617 in F2023.
36 MATERIALS SCIENCE↗
Abnormal grain growth of 68Cu–16Al–16Zn alloys for elastocaloric cooling via cyclical heat treatments
Abstract Cu-based superelastic shape memory alloys are promising for low-stress elastocaloric cooling. We have synthesized bulk alloys of 68Cu–16Al–16Zn under different conditions in order to promote its grain growth and enhance its elastocaloric properties. High-temperature x-ray diffraction of untreated 68Cu–16Al–16Zn alloy showed that the phase boundary between the α + β mixed phases and the high temperature phase ( β phase) was between 973 K and 1023 K. Based on this result, the 68Cu–16Al–16Zn alloy was heated and cooled in a furnace repeatedly between 773 K and 1173 K. The maximum grain size after heat treatment of the ingot rolled to 67% reached 11.1 mm. The latent heat of the martensitic transformation after grain growth was 6.3 J g −1 , which is higher than the previously reported value for the compound. The stress–strain curve of 68Cu–16Al–16Zn rolled to 67% rolling with cyclical heat treatments showed a maximum stress of 106 MPa at 4.5% strain, with adiabatic temperature change of 5.9 K in heating during stress loading and 5.6 K in cooling in stress removal. Furthermore, no fatigue in the stress–strain behavior was observed up to at least 60 000 mechanical cycles at 2% strain.
36 MATERIALS SCIENCE↗
Effects of Strain Gauge Coatings on Water Intrusion in Submerged Composite Coupon Testing
Marine energy structures are typically made using composite materials and are repeatedly loaded by currents and waves. Submersion and repeated loading lead to two environmental effects: moisture intrusion and mechanical fatigue. To understand their combined effects, submerged fatigue testing can be used. Submerged fatigue testing often requires submerged instrumentation to validate component manufacturing methods and models. Strain measurements are critical for understanding marine energy component loads. One common method for measuring strain is by using foil strain gauges, but the durability of strain gauges in submerged fatigue conditions is not well-understood. To increase strain gauge durability and protection from contamination, delamination, and water intrusion, strain gauge coatings may be applied over strain gauges and wire connections. In this study, strain gauges were adhered to composite coupons, coated, and mechanically tested in a water tank. Cycles to composite failure, cycles to strain gauge failure (SGF), strains, and SGF modes were used to measure the effects of strain gauge coatings on composite fatigue life and strain gauge durability. The coatings did not have significant effects on composite fatigue life or strain gauge durability. The methods developed and measurements taken at the coupon scale in this study will be used to inform methods and designs for subsequent submerged subcomponent testing, full-scale testing, and standards development. The benefits of designing marine energy structures to informed standards and designs are decreased lifetime costs and increased reliability and energy production, ultimately leading to a sustainable and low-carbon energy system.
composite materials↗
Thermomechanical analysis and modeling of a high-temperature light trapping planar cavity solar receiver
The development of durable particle-based high-temperature solar receivers is critical for advancing concentrating solar-thermal (CST) technologies to enable high-efficiency power generation and industrial process heat. Here, this study presents a computational framework to evaluate the thermomechanical performance of a proposed enclosed light-trapping planar cavity receiver designed for particle-based thermal energy systems. The receiver incorporates absorptive cavities and fluidized particle-bed channels to enhance heat capture and reduce thermal losses. Finite element analysis (FEA) is employed to assess stress, strain, and creep-fatigue behavior under concentrated solar flux using realistic thermal boundary conditions derived from coupled system models and experimental assembly parameters. The analysis investigates the influence of particle-to-wall heat transfer coefficients (HTC) ranging from 800 to 1800 W/m 2 .K on the thermomechanical response of six candidate high-temperature alloys: Alloy 740H, Alloy 282, Alloy 617, 316H, Alloy 230, and 800H. Results show that increasing HTC reduces thermal gradients, leading to lower stresses and strains and extended minimum predicted creep life. While all materials satisfy fatigue life requirements under the investigated conditions, significant differences in creep resistance are observed. Alloy 740H consistently exhibits the longest minimum predicted creep life and the most favorable durability margins, followed by Alloy 282, with the remaining materials showing reduced creep resistance under identical loading. The reported creep lives are conservative lower-bound estimates intended for comparative material evaluation. This framework highlights the critical roles of material selection and geometry optimization in improving mechanical durability and reliability of solar-thermal receivers, forming a foundation for future experimental validation and design optimization.
14 SOLAR ENERGY↗
Enhancing functionalities in carbon fiber composites by titanium dioxide nanoparticles
Carbon fiber composite's high specific strength makes it incredibly useful for structural applications. However, their low strain-to-failure can be problematic in structural applications that can potentially see high strain conditions or high fatigue cycles resulting in sudden, catastrophic failure. This is further complicated by damage manifesting within the composite thus not showing damage indicators on the surface. Therefore, monitoring the structural integrity and strain history of the composite in application by itself—while maintaining positive composite performance—is vital to ensure safe operation. In this study, a homogeneous dispersion of TiO 2 nanoparticles on carbon fiber is demonstrated to generate a piezoresistive carbon fiber polymer matrix composite with enhanced self-sensing capabilities. The nanoparticle-embedded composites also exhibited superior strength and damping potential compared to the nanoparticle-free composites. The apparent interlaminar shear strength increased by up to 15% and the damping loss factor increased by an average of 150% while the piezoresistive sensitivity increased by up to 180% with the addition of a small weight fraction of nanoparticles to the fiber surface. These results demonstrate an approach to simultaneously improve the sensing capabilities, damping behavior and mechanical strength of carbon fiber composites by simply adding nanoparticles in the fiber sizing using a commercially scalable deposition method.
36 MATERIALS SCIENCE↗
Antiferroelectric Ceramics for Energy–Efficient Capacitors by Theory–Guided Discovery
Antiferroelectric ceramics, via the electric-field-induced antiferroelectric (AFE)–ferroelectric (FE) phase transitions, show great promise for high-energy-density capacitors. Yet, currently, only 70–80% energy release is found during a charge–discharge cycle. Here, for PbZrO 3 -based oxides, geometric nonlinear theory of martensitic phase transitions is applied (first used to guide supercompatible shape-memory alloys) to predict the reversibility of the AFE–FE transition by using density-functional theory to assess AFE/FE interfacial lattice-mismatch strain that assures ultralow electric hysteresis and extended fatigue lifetime. A good correlation of mismatch strain with electric hysteresis, hence, with energy efficiency of AFE capacitors is observed. Here, guided by theory, high-throughput material search is conducted and AFE compositions with a near-perfect charge–discharge energy efficiency (98.2%), i.e., near-zero hysteresis are discovered. And the fatigue life of the capacitor reaches 79.5 million charge–discharge cycles, a factor of 80 enhancement over AFE ceramics with large electric hysteresis.
36 MATERIALS SCIENCE↗
Experimental Investigation of Concrete Fatigue in Axial Compression
The use of concrete in fatigue critical structures, such as wind turbine towers, has necessitated the replacement of simplistic (and therefore insufficient) fatigue design recommendations with more accurate and advanced fatigue models that can consider a greater complexity of stress states and materials. As the first part of a multistage test series, an experimental investigation was conducted to determine the fatigue life of concrete subjected to axial compressive fatigue loading, focusing on the relatively high-cycle fatigue domain. Here, a wide range of values for maximum stress levels and stress ratios were considered. The experimental results were compared against existing predictive models, and the most applicable model was identified. Concrete strain and stiffness behavior during fatigue loading were also investigated and reported. Based on the observed behavior, a hypothesis for identifying the impending occurrence of fatigue failure, based on the monotonic stress-strain curve, is examined.
17 WIND ENERGY↗
Fatigue Testing and Characterization of Pre-hydrided Zircaloy-4 Cladding Tubes
The solubility of hydrogen in Zircaloy-4 (Zry-4) at the cladding operating temperature is near 100 wt. ppm. Above this solubility limit, excess hydrogen precipitates as δ-hydride platelets in the cladding material. Because of the effect of the thermal gradient across the cladding thickness on the migration and precipitation of hydrogen, hydride rims are often observed at the cladding outer surface; under excessive corrosion conditions hydride blisters are possible. It is well known that the fatigue of metal alloys, especially high cycle fatigue, is sensitive to the status of surface including the microstructure, roughness, and residual stress. Thus, the question considered herein, is whether excessive hydrogen pickup modifies the microstructure such that it has a degradation effect on the fatigue performance of cladding during operation. This report describes the evaluation of fatigue performance of a pre-hydrided Zry-4 cladding. A commercial Zry-4 was polished and pre-hydrided to 800 ppm and 1300 ppm H contents. The fatigue testing was conducted under strain control at 5 Hz with fully-reversed bending by using a cyclic integrated reversible bending fatigue tester (CIRFT). Six specimens with 1300 ppm and one specimen with 800 ppm were tested. Significant variation in test results were observed. While two of the 1300 ppm specimens failed with less than 1 ×10 5 cycles (at 0.32% and 0.41%), the four other samples did not fail over the strain amplitude range of 0.25% to 0.38%. Interestingly, the fracture initiation site of the failed samples was on the outside diameter (OD) surface rather than on the inside diameter (ID) surface as is typical for the as-polished cladding. This suggested a degrading effect of the hydriding process. Subsequently, three of the unfailed specimens were then further tested at ~0.43% to observe where failure initiation occurred. Significant variation was also observed in these three specimens. One specimen failed at ~9000 cycles while the two others failed at 43000 and 1.06 ×10 5 cycles. The performance here correlated to the location of failure initiation; failure initiated on the OD in the sample that failed after 9000 cycles while it initiated on the ID in the sample that failed after 43000 and 1.06 ×10 5 cycles. Flat features at the OD initiation sites suggest a brittle hydride feature on the surface of those samples was the cause of the degradation in fatigue performance, though the overall hydrogen levels in all samples was similar. A summary of all the observations is provided below: • The un-failed specimens with 1300 ppm H were cycled to failure with a higher amplitude near 0.43%. In addition, the fatigue-treated specimen tended to have a longer fatigue at the same induced amplitude. • Fractography revealed a mixed failure mode for the pre-hydrided specimen. Particularly, the specimen with fracture initiation site (FIS) located on the outer diameter surface of tube tended to have a shorter fatigue life than that of FIS on the inner diameter surface. • Etched cross section was shown to have hydride platelets aligned with tube longitudinal axis as expected, and the density of hydrides is at the similar level as in literature data. Meanwhile, a LECO procedure was applied for hydrogen concentration measurement, which showed the measured hydrogen contents are close to the nominal value. • With the polished cladding tube as baseline, O’Donnell-Lager (O-L) analysis showed that a decrease of about 50% in reduction-of-area (RA) would be needed for the O-L fitting to the fatigue data of 1300 ppm cladding. The suggestion for the next steps is provided.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Fatigue-Like Behavior of Silver Metallization Gridlines and Proposed Damage Mechanics Model
In this work, we present a novel method to evaluate the fracture and fatigue-like behavior of crystalline silicon PV cell metallization. Initial results demonstrate that silver metal gridlines are capable of bridging a ~10–20 µm gap prior to becoming electrically open and do demonstrate fatigue-like behavior under cyclic straining conditions. This later phenomenon was well fit with a traditional power law equation for high cycle fatigue and enabled the development of a damage mechanics model for gridline failure.
41 EE - Solar Energy Technologies Office (EE-4S)↗