Search NASA⌕ Search

SEARCH · Search NASA

Results for “STRESS WAVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Sound speed determination in copper shock compressed to 190 GPa

Sound speed measurements in shock compressed solids have long been valuable for the development of equations of state at extreme conditions, shock-induced phase transformations, and a comprehensive characterization of the thermophysical response of high-pressure standards. We present results from plate impact experiments to 190 GPa to determine the longitudinal sound speed in copper—an important high-pressure standard. Surprisingly, the sound speeds determined using the two most common experimental techniques—the front surface impact (FSI) approach and the release wave overtake (RWO) approach—diverge significantly for stresses greater than ~100 GPa. Further analyses, including numerical simulations, show that the FSI experiments provide the correct sound speeds and that fundamental assumptions underlying the RWO method are likely violated due to the complex release response of shock compressed copper. The sound speeds determined using the FSI approach provide for a more accurate high-pressure description of copper in dynamic compression experiments. The present findings are in contrast to the results for shock compressed silver [Wallace et al., Phys. Rev. B 104, 214106 (2021)], where both methods provided consistent sound speed results. Thus, the findings presented here demonstrate the need to experimentally verify the validity of the RWO method on a case-by-case basis. Finally, we note that even at the high stresses in the present work, the copper unloading response shows a time-dependent, quasielastic response often observed in metals at lower stresses.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Sediment transport and morphodynamic changes due to upstream variation and sea level rise on the Western Mekong Delta, Vietnam

The hydrological and morphological dynamics across the Vietnam Mekong Delta (VMD) coastline are increasingly shaped by human interventions and climate change, affecting the sustainability of socio-economic environments. This study employs the TELEMAC-MASCARET modeling system (TELEMAC-2D, TOMAWAC, and SISYPHE modules) to simulate hydrodynamics, sediment transport, and morphological changes for a 10-year period under baseline (SC1) and future climate (SC2) scenarios, considering wave climatology of Northeast (NEM) and Southwest monsoons (SWM). The results of sedimentation and erosion were analyzed across five key coastal zones from Ca Mau Cape (KV1) to Ha Tien (KV5). Model results highlight distinct seasonal patterns of sediment redistribution shaped by monsoonal flows, wave action, and seabed morphology. During the NEM, sediment deposition is concentrated near estuarine zones, while the SWM favors offshore sediment accumulation due to perpendicular wave actions, and shallow, gently sloping bathymetry that dissipates wave energy. Coastal erosion predominantly occurs at convex shoreline features subjected to stronger coastal currents, particularly in fine-grained sediment areas. Under future sea level rise and land subsidence scenarios, reduced flow velocities lead to lower bottom shear stress, promoting deposition and mitigating erosion problems despite increased wave energy. Besides that, sediment transport analyses across 14 cross-sections (C-S) reveal a southward trend during the NEM and a northward reversal during the SWM, with upstream sediment reductions primarily influencing near-estuarine zones and exerting minimal impact beyond the mid-coastal regions. Furthermore, these findings advance the understanding of sediment redistribution processes under climate change and seasonal change, and provide a scientific basis for adaptive coastal management and sustainable development.

Climate change↗
DOE OSTI2024

Shock-induced twinning/detwinning and spall failure in Cu–Ta nanolaminates at atomic scales

Here, this study provides new insights into the role of interfaces on the deformation and failure mechanisms in shock-loaded Cu–Ta–Cu trilayer system. The thickness of the Ta layer, piston velocities, and shock pulse durations were varied to explore the impact of impedance mismatch and loading conditions on spallation behavior and twin formation. It was found that the interfaces play a crucial role in the dynamic response of these multilayered systems since secondary reflection waves generated at the interfaces significantly affected the peak stress and pressure profiles, influencing void nucleation and failure modes. In the trilayer systems, failure predominantly occurred at interfaces and within the Ta layer, with void nucleation sites and twinning behavior being markedly different compared to single-crystal Cu and Ta. Increasing the Ta layer thickness modified the wave interactions, leading to different failure locations. Higher piston velocities were associated with increased spall strength by enhancing wave interactions and void formation, particularly at the interfaces and within the Ta layer, under specific configurations. Additionally, shorter shock pulse durations facilitated earlier initiation of the release fan, reducing twin formation and altering the failure dynamics by accelerating twin annihilation and pressure release.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Using a 1D Radially Symmetric Coda Envelope Model for Robust Moment Magnitude ( M w ) Estimation in Iraq’s Tectonically Diverse Zones

Robust estimation of moment magnitude (M w ) can be challenging for Iraq due to the strong lateral heterogeneity across diverse tectonic zones. We aim to improve moment magnitude estimation by investigating the reliability of using a 1D coda envelope model in diverse tectonic zones of different lateral effects and offer a way forward for reliable estimates of M w for small events that are difficult to waveform model. Iraq comprises two main tectonic zones: (1) the Outer platform, consisting of the northwestern Zagros fold-thrust belt and the Mesopotamian foredeep, and (2) the Inner Arabian platform which is overlain by the Iraqi desert. A simple 1D coda envelope model was used because coda waves have a low sensitivity to the source and path heterogeneity. Three separate coda calibrations were conducted to investigate the robustness of a single 1D calibration to fit the country: Whole-region calibration, Zagros calibration, and Mesopotamia calibration. In the whole-region calibration, we used stations from both the Zagros and Mesopotamia zones. In the two other calibration models, we used only stations that were in those particular zones. Ground-truth reference spectra derived from the coda spectral ratio method were used to constrain high-frequency site terms. There was no drastic difference when comparing the moment magnitudes calculated from the waveform modeling and the three calibration models. The results show that the 1D coda envelope model is a reliable method even for a region with diverse tectonic zones. Therefore, we recommend using the whole-region calibration model for moment magnitude estimation that provides more complete path coverage and avoids biases introduced by path correction failures. The proposed calibration is a fundamental step in updating the comprehensive earthquake catalog and probabilistic seismic hazard assessments for Iraq.

58 GEOSCIENCES↗
DOE OSTI2025

Optimizing ablator thickness for laser shock experiments

In laser shock experiments, a well-defined, flat-top shock wave at the ablator/sample interface is important for accurately probing material response under uniaxial strain compression. However, the relationship between the ablator thickness and the resulting shock wave characteristics is insufficiently understood, limiting the ability to design optimal experiments. To address this need, we conducted a systematic experimental study using a 100 J laser to shock-compress polyimide ablators to peak stresses ranging from 20.4 to 111.6 GPa. Laser interferometry diagnostics measured the transmitted wave profiles at the ablator/sample interface, consistently showing a single jump followed by a constant peak state before the arrival of release waves. Here, by analyzing shock transit time, flat-top duration, and stress, our results establish a framework for selecting ablator thickness to maximize the flat-top duration, improving the precision and reproducibility of laser shock experiments.

design of experiments↗
DOE OSTI2025

Synoptic and Mesoscale Modulation of Dynamic and Thermodynamic Impacts on Central Arctic Sea Ice During MOSAiC

The primary objectives of this proposed project are to determine 1) to what extent dynamic and thermodynamic air‐ice interactions in the Central Arctic are driven by atmospheric synoptic and mesoscale phenomena, and 2) the key processes involved in these interactions. These phenomena include large‐scale features such as fronts, high‐ and low‐pressure systems, low‐level jets, and cloud bands, but may also include smaller‐scale phenomena such as mesoscale instabilities (e.g., symmetric instability or slantwise convection), transient meso‐lows and gravity waves. Dynamic air‐ice interactions include direct atmospheric stress and atmospheric stress divergence/deformation; thermodynamic air‐ice interactions involve the net surface energy budget, especially in association with non‐stratocumulus clouds generally occurring with stronger dynamical forcing.

58 GEOSCIENCES↗
DOE OSTI2025

Simulating Isotropic Rayleigh Wave Horizontal to Vertical Ratios at Rock Valley

Elastic anisotropy in the subsurface can manifest from pre-existing structure or stress-induced cracking – both phenomena are of interest at the Rock Valley site in Nevada. The azimuthal dependence of Rayleigh wave ellipticity, also known as H/V, can reveal elastic anisotropy, but the effect of isotropic variability in H/V must first be accounted for. To that end, we simulate synthetic seismograms from a ring of sources in a fully 3-D isotropic velocity model that captures the geology at Rock Valley. We measure H/V from these waveforms and compare them with H/V predictions obtained using 1D models extracted at specific locations from the 3D model. We find that an average of the azimuthal H/V measurements from the 3-D simulations and 1-D predictions agree, but that the azimuthal variability of H/V is a large fraction of the mean value. These results estimate the noise character in azimuthal H/V so it can be factored out of future anisotropic simulations.

58 GEOSCIENCES↗
DOE OSTI2024

Investigation of acoustic waves under subsurface conditions to improve the predictions of rock mechanical properties and natural fracture characteristics

Mechanical properties and natural fracture characteristics are critical to investigate for subsurface engineering applications, including carbon storage, well drilling, and stimulation, as they govern rock stability, fluid flow, and mechanical behavior under stress. This dissertation integrates experimental and machine learning approaches to enhance the prediction and understanding of these properties by analyzing acoustic wave behavior under varied subsurface conditions. First, the influence of temperature, pore pressure, and supercritical CO2 (scCO2) saturation on poroelastic properties is examined using Gray Berea sandstone samples. The results show that temperature and pore pressure significantly affect the bulk modulus and Biot’s coefficient, while scCO2 saturation impacts rock compressibility, informing strategies for effective geological carbon storage. The study extends this understanding by experimentally evaluating the impact of reservoir depletion on the dynamic mechanical properties of the emerging Caney shale in South Oklahoma with the employment of unsupervised machine learning to predict static mechanical properties across the Caney shale. Integrating petrophysical data and chemostratigraphy, the workflow—featuring K-means clustering, principal component analysis (PCA), and inverse distance weighting (IDW)—improves stratigraphic characterization and the estimation of static-to-dynamic modulus ratios, which is vital for optimizing drilling and stimulation strategies. Finally, the work explores how natural fracture characteristics in shale influence acoustic waveforms and shear wave splitting (SWS) analysis. Experimental data on fractured samples under different stress and temperature conditions, combined with machine learning models such as K-nearest neighbors (KNN) and extreme gradient boosting (XGBoost), reveal key fracture properties impacting SWS and wave propagation. Together, these studies provide a comprehensive framework for linking acoustic wave behavior with rock properties, advancing the methods for monitoring and predicting geomechanical changes. The insights offered valuable implications for safer, more efficient CO2 injection, hydrocarbon extraction, and subsurface management.

Elkholy, Sherif↗
DOE OSTI2024

Stress field measurements using quantitative schlieren

Quantitative schlieren analysis is extended here to optically transparent solids in quasi-static and dynamic experiments to measure stress distributions. The quasi-static experiments in polymethyl methacrylate (PMMA) compared refraction angles and stress gradients calculated from schlieren images to the analytical Flamant solution of a line load on a half-space. The quantitative schlieren measurements of the stress field in the thin sample with a load compared well to the analytical solution. The analysis method was then extended to explosive induced shock waves in PMMA. The explosive induced response of PMMA was experimentally studied using high-speed schlieren to visualize the shock propagation in conjunction with Photon Doppler Velocimetry (PDV) to record surface velocity histories. The stress state estimated from the schlieren images was compared to the stress calculated from the PDV measurements. High-speed imaging limitations caused the shock wave to not be fully resolved in the images, but was resolved in the PDV measurement. The stress state behind the shock calculated from the high-speed images followed a similar trend to the stress calculated from the PDV measurements.

Physics↗
DOE OSTI2026

Regulating in situ gaseous deposition to construct highly durable Fe–N–C oxygen-reduction fuel cell catalysts

The activity–stability trade-off challenges the design of high-performance atomically dispersed iron–nitrogen–carbon (Fe–N–C) catalysts for the acidic oxygen reduction reaction in polymer electrolyte fuel cells. Here we develop an in situ chemical vapour deposition approach during catalyst synthesis to break the trade-off, producing highly stable Fe–N–C catalysts while maintaining adequate oxygen reduction reaction activity. The optimal catalyst exhibits a half-wave potential of 0.867 V, remaining unchanged after an accelerated stress test (AST) of 100,000 potential cycles in rotating disk electrode tests. In membrane electrode assemblies under H 2 –air conditions, it delivers 93 mA cm −2 at 0.8 V after a standard AST of 30,000 voltage cycles, and shows minimal current density losses (2.9% at 0.6 V; 14.2% at 0.7 V) after an extended AST up to 120,000 cycles. Furthermore, the catalyst’s durability improvement is primarily due to the in situ chemical vapour deposition, which strengthens Fe–N bonds, increases active-site density, mitigates iron aggregates and reduces surface porosity.

Chemical engineering↗
DOE OSTI2025

Mechanical form factors and densities of nonrelativistic fermions

The hadron physics community has been actively debating the interpretation of so-called mechanical properties of hadrons. Nonrelativistic quantum-mechanical systems like the hydrogen atom have been appealed to in these debates as analogies. Since such appeals are likely to continue, it is important to have Galilei-covariant expressions for matrix elements of the energy-momentum tensor. In this work, I obtain Galilei-covariant breakdowns of such matrix elements into mechanical form factors, with a special focus on spin-half states. I additionally study the spatial densities associated with these form factors, using the pilot wave interpretation to guide their breakdown into contributions from internal structure and from quantum-mechanical effects such as wave packet dispersion. For completeness, I also obtain nonrelativistic Breit frame densities.

form factors↗
DOE OSTI2026

Quantum stress and torsion distributions in the deuteron

Stress distributions in the deuteron are related to form factors of the asymmetric energy-momentum tensor through three-dimensional Fourier transforms. There are eleven such form factors, which we calculate in an impulse approximation. We compare the obtained form factors to prior results for the six form factors that have been previously calculated. We then elaborate on the formalism for relating the form factors to internal distributions of mass, mass flux, momentum, stresses, and forces, and obtain results for all of these distributions. We obtain the principal stresses for the symmetric part of the stress tensor, and show that the antisymmetric part describes the reorientation of fermion spin by torsion stress when the nucleon moves between the S and D waves. Force distributions in the nucleons depend on the so-called nonconserved form factors through the Cauchy momentum equation, and are nonradial owing to the presence of tensor forces and spin-orbit coupling.

QCD phenomenology↗
DOE OSTI2024

Determining Stress Orientation in Rock Valley, Nevada, Using Ambient Seismic Noise

The stress field and the mechanical properties of rocks are important to consider for nuclear explosion monitoring due to their effect on seismic wave radiation from earthquakes and explosions. At the Rock Valley Direct Comparison site, the regional orientation of the maximum horizontal compressive stress (SH max ) is well constrained, but it is unknown whether there are local heterogeneities. Here, I show that stress-induced anisotropy in nonlinear elasticity can be used to estimate the orientation of SH max . Rocks have compliant internal contacts, such as fractures and mineral grain boundaries, that respond to applied strains more strongly than individual mineral crystals. This strain response is asymmetric between compressive and dilatational strains and is affected by anisotropy in the ambient stress field. Traditional seismic velocity measurements are of strain-averaged velocity, which is less sensitive than nonlinear elasticity to the behavior of compliant internal contacts and therefore the stress field and fracture behavior. My results show that the orientation of SH max measured using ambient seismic noise aligns with regional estimates, with some heterogeneity that can also be explained by the limitations of the seismic array. I demonstrate the potential of a passive technique for monitoring the stress field in places that currently lack local measurements.

58 GEOSCIENCES↗
DOE OSTI2026

Suppression of ion temperature gradient modes by Alfvén activity above a drive threshold in DIII-D

A recent study demonstrates that the suppression of ion temperature gradient (ITG) modes can occur during the nonlinear evolution of toroidicity-induced Alfvén eigenmodes (TAEs) in the DIII-D tokamak [Du et al., Phys. Rev. Lett. 135, 265101 (2025)]. In that work, ITG was suppressed by the formation of a narrow, TAE-induced shear flow layer, whose shearing rate exceeded the ITG decorrelation rate. Here, the shear flow arises from an imbalance between Reynolds and Maxwell stress forces, as the TAE departs from the conventional shear Alfvén wave polarization. This follow-up paper systematically identifies the plasma conditions required for robust ITG suppression through a series of comparative experiments. The results show that TAEs routinely suppress ITG turbulence in plasmas with higher local safety factor (q), elevated fast-ion beta, and larger populations of fast ions on passing orbits, i.e., conditions consistent with the substantial TAE drive. Database analysis further reveals the existence of a threshold in TAE drive for ITG suppression. That is, once the drive exceeds a critical value within a favorable q window, the system undergoes the nonlinear bifurcation process, characterized by a sharp increase in TAE saturated amplitudes at a nearly fixed fast ion drive, suppression of ITG turbulence, and the formation of an internal thermal transport barrier at the localized radii.

Du, X. D. [General Atomics, San Diego, CA (United ↗
DOE OSTI2025

A Deep Learning-Aided Workflow for Decoding the Stress Regime of Southern Nevada

The Rock Valley fault zone in southern Nevada has a notable history of seismic activity and is the site of a future direct comparison experiment of explosion and earthquake sources. This study aims to gain insight into regional tectonic processes by leveraging recent advances in seismic monitoring capabilities to elucidate the local stress regime. A crucial step in this investigation is the accurate determination of P-wave first-motion polarities, which play a vital role in resolving earthquake focal mechanisms of small earthquakes. Here, we deploy a deep learning-based method for automatic determination of first-motion polarities to vastly expand the polarity dataset beyond what has been reviewed by human analysts. By the integrating P-wave polarities with new measurements of S/P amplitude ratios, we obtain robust focal mechanism estimates for 1306 earthquakes with a local magnitude of 1 and above occurring between 2010 and 2023 in southern Nevada. We then use the focal mechanism catalog to examine the regional stress orientation, confirming an overall trans-tensional stress regime with smaller scale complexities illuminated by individual earthquake sequences. These findings demonstrate how detailed analyses of small earthquakes can provide fundamental information for understanding earthquake processes in the region and inform future experiments at the Nevada National Security Site.

58 GEOSCIENCES↗
DOE OSTI2026

Towards the Ultimate Strength of Medium‐Entropy Alloys Through Pulsed Lasers

The tensile strength of metals at extreme strain rates is a key predictor of their performance in ballistic and structural impact applications. An important experimental method to reach these extreme strain rates is the use of high-amplitude, short-duration pulsed lasers. The Jupiter Laser Facility at the Lawrence Livermore National Laboratory enabled probing for the first time the mechanical response of several promising High Entropy Alloys at times on the order of nanoseconds (strain rates of ∼10 7 and ∼10 9 s −1 ). The measured strength is in the range of 6 to 10 GPa, ten times the quasistatic value. The mechanisms of plastic deformation and failure were identified and quantified through analysis and molecular dynamics simulation. The reflected wave amplitudes, obtained by VISAR, were used to determine the tensile (spall) stress. The high tensile strength obtained is due to two factors: the strain-rate dependence of plastic flow and the kinetics of void nucleation, growth, and coalescence. The experimental results are compared with an analytical prediction considering both grain-interior and grain-boundary void initiation. Molecular dynamics simulations, conducted at strain rates of 10 8 and 10 9 s −1 , rationalize the experimental results. In conclusion, they provide valuable information about the process of failure evolution, and reveal that grain boundary separation plays a pivotal role in spalling.

Materials science↗
DOE OSTI2025

All the light we cannot see: Climate manipulations leave short and long‐term imprints in spectral reflectance of trees

Abstract Anthropogenic climate change, particularly changes in temperature and precipitation, affects plants in multiple ways. Because plants respond dynamically to stress and acclimate to changes in growing conditions, diagnosing quantitative plant‐environment relationships is a major challenge. One approach to this problem is to quantify leaf responses using spectral reflectance, which provides rapid, inexpensive, and nondestructive measurements that capture a wealth of information about genotype as well as phenotypic responses to the environment. However, it is unclear how warming and drought affect spectra. To address this gap, we used an open‐air field experiment that manipulates temperature and rainfall in 36 plots at two sites in the boreal‐temperate ecotone of northern Minnesota, USA. We collected leaf spectral reflectance (400–2400 nm) at the peak of the growing season for three consecutive years on juveniles (two to six years old) of five tree species planted within the experiment. We hypothesized that these mid‐season measurements of spectral reflectance capture a snapshot of the leaf phenotype encompassing a suite of physiological, structural, and biochemical responses to both long‐ and short‐time scale environmental conditions. We show that the imprint of environmental conditions experienced by plants hours to weeks before spectral measurements is linked to regions in the spectrum associated with stress, namely the water absorption regions of the near‐infrared and short‐wave infrared. In contrast, the environmental conditions plants experience during leaf development leave lasting imprints on the spectral profiles of leaves, attributable to leaf structure and chemistry (e.g., pigment content and associated ratios). Our analyses show that after accounting for baseline species spectral differences, spectral responses to the environment do not differ among the species. This suggests that building a general framework for understanding forest responses to climate change through spectral metrics may be possible, likely having broader implications if the common responses among species detected here represent a widespread phenomenon. Consequently, these results demonstrate that examining the entire spectrum of leaf reflectance for environmental imprints in contrast to single features (e.g., indices and traits) improves inferences about plant‐environment relationships, which is particularly important in times of unprecedented climate change.

Stefanski, Artur [Department of Forest Resources U↗
DOE OSTI2024

Utah FORGE: Direct Shear Test Data for Investigating Seismic Precursors to Shear Failure of Fractures

This dataset includes results of direct shear tests to investigate the mechanical and geophysical response of dry and saturated fractures in Indiana limestone and Sierra White granite. Direct shear tests were performed on tensile-induced fractures in Indiana limestone and Sierra White granite in a custom water-pressurized chamber. The provided Excel files include the representative seismic wave signals and the normalized wave amplitudes of ultrasonic wave transducers. A link to the published journal article presenting the data and describing the experiment in detail is provided as well.

15 GEOTHERMAL ENERGY↗