SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Definitions of methods of measurements of supporting and control surface areas are presented. Methods for measuring the supporting surface, i.e., the wing area, and the control surfaces, i.e., the horizontal tail area, the vertical tail area, and the trailing control surface areas are defined. Illustrations of each of the areas are included.
Perovskite oxides have generated interest as robust, low-temperature oxygen carrier materials for a variety of clean energy applications, including chemical looping gasification and air separations. Methods to improve O 2 desorption kinetics are vital to allow these carriers to compete economically with traditional metal oxide carriers or cryogenic separations. In this report we investigated the cumulative roles that surface area, pretreatment, and elemental composition have on the oxygen storage properties of a state-of-the-art carrier system, Sr 1-x Ca x FeO 3-δ (x = 0.20, 0.25, 0.30) synthesized using multiple methods. Porous materials synthesized by the Pechini, or citrate, method had their surface area controlled using the synthesis temperature. The high surface area of the Sr 0.7 Ca 0.3 FeO 3-δ materials is most beneficial at low operating temperatures, such as 350 and 400 °C, as their reduction rates are twice as fast as those obtained with their bulk counterparts. These effects are observed at higher operating temperatures and within a single composition, but temperature tunability using variable Ca 2+ substitution in the Sr 1-x Ca x FeO 3-δ overshadows the improvements gained from higher surface areas. Additionally, we establish that pretreatment in N2 at an elevated temperature is necessary to enhance kinetics further. For maximum efficiency, pretreatment at the synthesis temperature is suggested for the Pechini method-synthesized systems, whereas 800 °C is adequate for bulk materials.
Not Available
Not Available
A high-surface-area p-type porous Si photocathode containing a covalently immobilized molecular Re catalyst is highly selective for the photoelectrochemical conversion of CO 2 to CO. It gives Faradaic efficiencies of up to 90% for CO at potentials of –1.7 V (versus ferrocenium/ferrocene) under 1 sun illumination in an acetonitrile solution containing phenol. Here, the photovoltage is approximately 300 mV based on comparisons with similar n-type porous Si cathodes in the dark. Using an estimate of the equilibrium potential for CO 2 reduction to CO under optimized reaction conditions, photoelectrolysis was performed at a small overpotential, and the onset of electrocatalysis in cyclic voltammograms occurred at a modest underpotential. The porous Si photoelectrode is more stable and selective for CO production than the photoelectrode generated by attaching the same Re catalyst to a planar Si wafer. Further, facile characterization of the porous Si-based photoelectrodes using transmission mode FTIR spectroscopy leads to highly reproducible catalytic performance.
In naval architecture, it is customary to determine the wetted surface of a ship by means of some formula which involves the principal dimensions of the design and suitable constants. These formulas of naval architecture may be extended and applied to the calculation of the surface area of airship envelopes by the use of new values of the constants determined for this purpose. Surface area coefficients were calculated from the actual dimensions, surfaces, and volumes of 52 streamline bodies, which form a series covering the entire range of shapes used in the present aeronautical practice.
We report the synthesis and electrocatalytic activity of Fe x Ni 100-x electrochemically deposited films were investigated. Films were evaluated for the hydrogen evolution reaction (HER) in alkaline media with respect to composition and electrochemically active surface area (ECSA). Results demonstrate that films of higher or equal Fe content had an ECSA tenfold greater than films with higher Ni. When normalized by geometric surface area, Fe 50 Ni 50 films required the lowest overpotential of -390 mV to reach a current density of -10 mA cm -2 . However, when normalized by the ECSA, intrinsic HER activity increases as Ni content increases. Tafel slope, ECSA, microscopy, and impedance spectroscopy analyses allow a decoupled analysis of surface area versus activity effects on overall measured HER activity. Furthermore, these analyses collectively demonstrate that the increase in electrocatalytic activity is attributed to the increase in ECSA and not to an enhancement in the intrinsic activity by Fe and Ni component interactions.
Abstract High-surface-area α-Al 2 O 3 nanoparticles are used in high-strength ceramics and stable catalyst supports. The production of α-Al 2 O 3 by phase transformation from γ-Al 2 O 3 is hampered by a high activation energy barrier, which usually requires extended high-temperature annealing (~1500 K, > 10 h) and suffers from aggregation. Here, we report the synthesis of dehydrated α-Al 2 O 3 nanoparticles (phase purity ~100%, particle size ~23 nm, surface area ~65 m 2 g −1 ) by a pulsed direct current Joule heating of γ-Al 2 O 3 . The phase transformation is completed at a reduced bulk temperature and duration (~573 K, < 1 s) via an intermediate δʹ-Al 2 O 3 phase. Numerical simulations reveal the resistive hotspot-induced local heating in the pulsed current process enables the rapid transformation. Theoretical calculations show the topotactic transition (from γ- to δʹ- to α-Al 2 O 3 ) is driven by their surface energy differences. The α-Al 2 O 3 nanoparticles are sintered to nanograined ceramics with hardness superior to commercial alumina and approaching that of sapphire.
The thermochemical stability of lanthanum strontium cobalt ferrite (LSCF) processed between 1000 °C–1200 °C via the in situ carbon templating method was studied. This method generates high surface area ceramics at traditional solid oxide fuel cell (SOFC) sintering temperatures by generating a carbon template in situ and subsequently removing the template by oxidation at 700 °C. Argon processed samples produced an amorphous carbon template, whereas nitrogen tended to form graphitic carbon. Prior to the oxidation step, nitrogen samples comprised larger La 2 O 3 crystallites (22–40 nm) compared to argon (9–17 nm). Upon oxidation, argon samples resulted in a pure LSCF phase with surface areas in the 21–29 m 2 ·g −1 range, whereas nitrogen samples contained significant impurities. This demonstrates that the size of La 2 O 3 crystallites formed during inert processing limited the ability to produce a pure LSCF phase. Symmetrical cells comprising nano-LSCF electrodes generated by the templating method were compared to cells sintered directly in air. Impedance results suggest that nano-LSCF cells and cells processed in air were dominated by interfacial charge transfer resistance and gas diffusion, respectively. The results map out conditions for preparing and integrating high surface area, nanostructured LSCF into SOFC electrodes at traditional sintering temperatures. Strategies for improving the interfacial resistance of nano-LSCF electrodes are discussed.
The correlation of flow-permeable surface area (FSSA) of porous initiator powder to its performance is well-established. More specifically, with age, such powders tend to coarsen (i.e., lose surface area), with an accompanying deterioration in performance. Commercially available permeametry apparatuses, such as that from Fisher Scientific or a more modern version from Micromeritics suffers from a few drawbacks, including: (1) the need to work with a fixed mass equivalent of 1 cm 3 of solid material; (2) the need to re-compact the material to monitor aging effects (which can introduce unwanted errors in the derived results); (3) a superfluous design that involves a reference plug, and for the older Fisher Scientific model, the need to eyeball water meniscus height that can lead to inaccuracies; (4) calibrated and tested only for samples packed in cylindrical geometries.
Following the eruption of Mount Pinatubo in June of 1991, the aerosol mass loading of the stratosphere increased from -1 Mt to approximately 30 Mt. This change in aerosol loading was responsible for numerous radiative and chemical changes observed within the stratosphere. As a result, the ability to quantify aerosol properties on a global basis during this period is important. Aerosol surface area density is a critical parameter in governing the rates of heterogeneous reactions, such as ClONO2 plus H2O yields HNO3 plus HOCl, which influence the stratospheric abundance of ozone. Following the eruption of Mt. Pinatubo, measurements by the Stratospheric Aerosol and Gas Experiment (SAGE 2) indicated that the stratospheric aerosol surface area density increased by as much as a factor of 100. Using SAGE 2 multi-wavelength aerosol extinction data, aerosol surface area density as well as mass are derived for the period following the eruption of Mt. Pinatubo through the present.
A novel metal dissolution coupled with reverse micelle formation approach is used as a generalized synthesis method for a series of high surface area metal titanates where the metals used are Bi, Mg, V, Mn, Fe, Co, Ni, Cu, Zn, Mo, W, and Ce. This study reports the highest surface areas published so far. The homogeneous distributions of the metals and titanium are observed in SEM-EDX and TEM mapping. The synthesized materials were comprehensively characterized using PXRD, Raman, nitrogen adsorption isotherms, SEM; EDX, TEM, TEM mapping, TGA, and XPS. The green catalytic oxidation of aniline to nitrosobenzene occurs within 30 min at room temperature when mesoporous W/Ti binary metal oxide is used as the catalyst. The radical mediated catalytic reaction gives excellent yields and the catalyst is reusable up to 4 reaction cycles without losing significant activity.
Mesoporous, multi-valent tungsten oxide with high surface area (209 m 2 /g) is synthesized via a novel metal dissolution coupled with reverse micelle formation approach. Mesoporous tungsten oxide with highest surface area reported is obtained by this method. The material is used as an excellent heterogeneous catalyst for the oxidation of organosulfur compounds present in crude oil. The complete oxidation of dibenzothiophene was observed with excellent yield (>99%) within 15 min at room temperature (20 °C). The catalyst is reusable up to 5 reaction cycles without losing significant activity. A green oxidant, H 2 O 2 is used and the reaction mechanism involves the activation of peroxo species by W 6+ . The oxidation activity decreases in the order of DBT > 4,6-DMDBT > 1-BT due to the changes in the electronic environment of sulfur and steric effects.
A mesoporous crystalline niobium oxide with tunable pore sizes was synthesized via the sol–gel-based inverse micelle method. The material shows a surface area of 127 m 2 /g, which is the highest surface area reported so far for crystalline niobium oxide synthesized by soft template methods. The material also has a monomodal pore size distribution with an average pore diameter of 5.6 nm. A comprehensive characterization of niobium oxide was performed using powder X-ray diffraction, Brunauer–Emmett–Teller, thermogravimetric analysis, scanning electron microscopy, transmission electron microscopy, UV–vis, and X-ray photoelectron spectroscopy. The material acts as an environmentally friendly, solid acid catalyst toward hydration of alkynes under with excellent catalytic activity (99% conversion, 99% selectivity, and 4.39 h –1 TOF). Brønsted acid sites present in the catalyst were found to be responsible for the high catalytic activity. Lastly, the catalyst was reusable up to five cycles without a significant loss of the activity.
The processes of hydration/dehydration and carbonation/decarbonation are investigated as an approach to provide higher surface area mixed metal oxides that are more active electrochemically. These materials are candidates for use as electrocatalysts and electrocatalyst supports for alkaline electrolyzers and fuel cells. For the case of the perovskite, LaCoO3 , higher surface areas were achieved with no change in structure and a more active oxygen electrocatalyst.
Mineral reactive surface area (RSA) is one of the key factors that control mineral reactions, as it describes how much mineral is accessible and can participate in reactions. This work aims to evaluate the impact of mineral RSA on numerical simulations for CO2 storage at depleted oil fields. The Farnsworth Unit (FWU) in northern Texas was chosen as a case study. A simplified model was used to screen representative cases from 87 RSA combinations to reduce the computational cost. Three selected cases with low, mid, and high RSA values were used for the FWU model. Results suggest that the impact of RSA values on CO2 mineral trapping is more complex than it is on individual reactions. While the low RSA case predicted negligible porosity change and an insignificant amount of CO2 mineral trapping for the FWU model, the mid and high RSA cases forecasted up to 1.19% and 5.04% of porosity reduction due to mineral reactions, and 2.46% and 9.44% of total CO2 trapped in minerals by the end of the 600-year simulation, respectively. The presence of hydrocarbons affects geochemical reactions and can lead to net CO2 mineral trapping, whereas mineral dissolution is forecasted when hydrocarbons are removed from the system.
Copyright © 2020 American Chemical Society. The rational design of high-performance electrocatalysts requires a detailed understanding of dynamic changes in catalyst properties, including oxidation states, surface area, and morphology under realistic working conditions. Oxide-derived Cu catalysts exhibit a remarkable selectivity toward multicarbon products for the electrochemical CO reduction reaction (CORR), but the exact role of the oxide remains elusive for explaining the performance enhancements. Here, we used operando X-ray absorption spectroscopy (XAS) coupled with simultaneous measurements of the catalyst activity and selectivity by gas chromatography (GC) to study the relationship between oxidation states of Cu-based catalysts and the activity for ethylene (C2H4) production in a CO gas-fed cell. By utilizing a custom-built XAS cell, oxidation states of Cu catalysts can be probed in device-relevant settings and under high current densities (>80 mA cm-2) for the CORR. By employing an electrochemical oxidation process, we found that the Cu oxidation states and specific ion species do not correlate with C2H4 production. The difference in the CORR activity is also investigated in relation to electrochemical surface area (ECSA) changes. While the hydrogen evolution reaction (HER) activity is positively correlated to the ECSA changes, the increased C2H4 activity is not proportional to the ECSA. Ex situ characterization from microscopic techniques suggests that the changes in the C2H4 activity and selectivity may arise from a morphological transformation that evolves into a more active structure. These comprehensive results give rise to the development of a cell regeneration method that can restore the performance of the Cu catalyst without cell disassembly. Our study establishes a basis for the rational design of highly active electrocatalysts for broad-range reactions in a gas-fed device.
Ice nucleation active site densities and nucleation rates are commonly determined by measuring the fraction of droplets that freeze at different temperatures. In analysing these experiments it is commonly assumed that variability in the immersed particle surface area and composition within a sample can be neglected, allowing a simple parameterization of ice nucleation efficiencies. Here it is shown that these approximations may result in large error, and translate into a bias in estimated active site densities of about six orders of magnitude. When applied in cloud models it may represent up to 5 K error in cloud glaciation temperature. A solution to this enduring problem is proposed for the first time. It is shown that by performing droplet freezing experiments varying mean particle surface area along with the temperature such a bias can be quantitatively removed. This amounts to differentiating the "freezing rate'' from the ice nucleation coefficient, or, the apparent and the actual active site density of a material. The proposed method will contribute to reduce existing uncertainties in the relative strength of the ice nucleation ability of different aerosol species, and the modeling of mixed-phase clouds.