SEARCH · Search NASA

Results for “Sampling frequency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Performance Evaluation of an Offshore Wave Measurement Buoy in Monochromatic Waves

The accurate measurement of waves underpins marine energy resource characterization, device design, and project development. Datawell wave buoys are widely deployed and have long served as a trusted standard for wave measurements. We quantify the measurement performance, including wave elevation and energy flux estimation, of a Datawell DWR-MkIII buoy using prescribed monochromatic heave motions on a large-amplitude six-degree-of-freedom motion platform at the National Laboratory of the Rockies, assuming the buoy behaves as an ideal wave follower. Commanded motions were validated with an optical motion tracking system while buoy elevation and raw acceleration were recorded. Wave elevations were propagated to wave energy flux estimation using four methods, including one frequency-domain method and three time-domain methods. The Bayesian optimization was applied for design of experiments, and records from three test sites were also applied and evaluated in the present study. Results show two error regions within the nominal period range of 1.6 s to 30 s. For wave periods between 5 s and 25 s, the buoy provides accurate wave height measurements. For short periods less than 5 s, the 1.28 Hz sampling frequency induces sub-Nyquist artifacts that bias elevation and can drive maximum energy flux estimation errors above 100%. For long periods exceeding 25 s, the buoy reported elevation is underpredicted with error depending on period but relatively independent of wave height, with maximum wave height and wave energy flux errors reaching 64% and 87%, respectively. Furthermore, analysis of three field-derived cases shows that frequency-domain estimates at 1.28 Hz agree within 2% of the corresponding 100 Hz estimates, while larger method-dependent differences are observed for the Hilbert method.

16 TIDAL AND WAVE POWER↗

DOE OSTI2023

Seasonal and tidal variations in hydrologic inputs drive salt marsh porewater nitrate dynamics

Salt marshes remove terrestrially derived nutrients en route to coasts. While these systems play a critical role in improving water quality, we still have a limited understanding of the spatiotemporal variability of biogeochemically reactive solutes and processes within salt marshes. We implemented a high-frequency sampling system to monitor sub-hourly nitrate (NO$^{–}_{3}$) concentrations in salt marsh porewater at Elkhorn Slough in central California, USA. We instrumented three marsh positions along an elevation gradient subjected to different amounts of tidal inundation, which we predicted would lead to varied biogeochemical characteristics and hydrological interactions. At each marsh position, we continuously monitored porewater NO$^{–}_{3}$ concentrations at depths of 10, 30, and 50 cm and porewater levels measured at 70 cm depth over seven deployments of ~10 days each that spanned seasonal wet/dry periods common to Mediterranean climates. We quantified tidal event hysteresis between NO$^{–}_{3}$ and water level to understand how NO$^{–}_{3}$ concentrations and sources fluctuate across tidal cycles. In dry periods, the NO$^{–}_{3}$-porewater level relationship indicated that the NO$^{–}_{3}$ source was likely estuarine surface water that flooded the transect during high tides and the salt marsh was a NO$^{–}_{3}$ sink. In wet periods, the NO$^{–}_{3}$-porewater level relationship suggested the salt marsh was a source of NO$^{–}_{3}$. Finally, these findings suggest that tidal and seasonal hydrologic fluxes together control NO$^{–}_{3}$ porewater dynamics and export and influence ecological processes in coastal environments.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Colloidal State Machines as Smart Tracers for Chemical Reactor Analysis

A widely utilized tool in reactor analysis is passive tracers that report the residence time distribution, allowing estimation of the conversion and other properties of the system. Recently, advances in microrobotics have introduced powered and functional entities with sizes comparable to some traditional tracers. This has motivated the concept of Smart Tracers that could record the local chemical concentrations, temperature, or other conditions as they progress through reactors. Herein, the design constraints and advantages of Smart Tracers by simulating their operation in a laminar flow reactor model conducting chemical reactions of various orders are analyzed. It is noted that far fewer particles are necessary to completely map even the most complex concentration gradients compared with their conventional counterparts. Design criteria explored herein include sampling frequency, memory storage capacity, and ensemble number necessary to achieve the required accuracy to inform a reactor model. Cases of severe particle diffusion and sensor noise appear to bind the functional upper limit of such probes and require consideration for future design. The results of the study provide a starting framework for applying the new technology of microrobotics to the broad and impactful set of problems classified as chemical reactor analysis.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2026

The Zooplankton International Geospatial dataset: A global repository of spatiotemporal freshwater zooplankton community composition data from lakes and reservoirs to support ecological research

Zooplankton transfer substantial energy in aquatic food webs and are used as indicators of environmental change. Syntheses of zooplankton community dynamics globally require datasets that span a wide range of environmental gradients; however, these datasets are limited due to methodological differences across programs, taxonomic inconsistencies, and a lack of standardized metadata. To reconcile these challenges, we created the Zooplankton International Geospatial (ZIG) dataset, which includes original zooplankton, water physical and chemical variables, and lake morphometric data from 311 inland lakes and reservoirs. ZIG includes waterbodies ranging in size from 0.005 to 82,100 km2 and spanning broad latitudinal (−47.26 to 64.90) and longitudinal ranges (−165.04 to 176.53). Temporal coverage for individual waterbodies ranges between 1 and 60 yr with sampling frequency ranging from annually to weekly. With its extensive coverage and content, we consider ZIG to be a cornerstone for future investigations of global scale lake biodiversity change.

Figary, Stephanie [Cornell University, Ithaca, NY]↗

DOE OSTI2023

Merging flux-variance with surface renewal methods in the roughness sublayer and the atmospheric surface layer

In this article, Two micrometeorological methods utilizing high-frequency sampled air temperature were tested against eddy covariance (EC) sensible heat flux (𝐻) measurements at three sites representing agricultural, agro-forestry, and forestry systems. The two methods cover conventional and newly proposed forms of the flux-variance (FV) and surface renewal (SR) schemes of differing complexities. The sites represent measurements in surface, roughness, and roughness to surface transitional layers. Regression analyzes against EC show that the most reliable FV and SR forms estimate 𝐻 with slopes within ±10% from unity and coefficient of determination 𝑅2 > 0.9 across all the three sites. The best performance of both FV and SR was found at the agricultural site with measurements well within the surface layer, while the worst was found for the tall forest with measurements within the roughness sublayer where its thickness needed to be additionally estimated. The main variable driving 𝐻 in FV is the temperature variance, whereas in SR, it is the geometry of ramp-like structures. Since these structures are also responsible for most of the temperature variance, a novel FV-SR approach emerging from combining the methods is proposed and evaluated against EC measurements and conventional FV and SR schemes. The proposed FV-SR approach requiring only a single fast response thermocouple is potentially independent of calibration and ameliorates some of the theoretical objections that arise when combining ramp statistics with similarity arguments. The combination of methods also provides new insights into the contribution of coherent structures to the temperature variance and its dependence on atmospheric stratification. Other potential utility of the new method is to include it in multi-tool assessments of surface energy fluxes, since a convergence or divergence of the results has a high diagnostic value.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Experimental study on the startup of the annular wick type heat pipe using fiber optical temperature measurement technique

This study used optical fiber-distributed temperature sensors to measure the internal and external temperature distributions of a water-cooled heat pipe. The sensor technology used in this study is fiber optical distributed temperature sensing, a distributed sensing technique based on the naturally occurring Rayleigh backscatter in optical fibers. This measurement technique provides maximum spatial resolution for static and semi-static applications. Using this sensor, the temperature distribution of the heat pipe's internal, external, vapor core, and the wick was measured with a spatial resolution of 0.65 mm, a sampling frequency of 40 Hz, and a temperature resolution of 0.1 °C. Through the measured temperature distribution database, the starting phenomenon, the effective length trend, and the limitation onset were observed. From the results, it is found that a high-temperature peak appears at the evaporator if a high initial power (75 W) is imposed on the heat pipe, even after the heat pipe approaches the normal operating status. The peak is not observed in a slower startup (30 W initial power then slowly increased to 75 W). It is also found that the temperature distributions and effective condenser length of the heat pipe highly depend on the cooling conditions. There are variations in the temperature according to the radial direction of the horizontal heat pipe due to gravity. In conclusion, lead and lag of the temperature evolution were observed at the onset of the operating limitations.

42 ENGINEERING↗

DOE OSTI2021

The Patterson function as auto-hologram and graph enables the direct solution to the phase problem for coherently illuminated atomistic structures

Abstract The coherent Patterson function, derived from the coherent scattering intensities from N atoms, can be described as an auto-holographic image, i.e., the superposition of N -holographic images in which each atom serves as the source of a different reference wave, and as a mathematical graph of the unknown structure. These insights indicate that the unknown structure is significantly over-determined by the inherent information content in a Patterson function by a factor of ( N − 1)/2 (for non-degenerate structures), independent of dimensionality. However, we also show that the ability to resolve the distinct features in the Patterson function depends strongly on details of the experimental design (data range, sampling frequency, and dimensionality). This re-interpretation suggests that the coherent Patterson function provides a natural context for describing the information content in coherent scattering, reveals that there is no inherent phase problem for coherently illuminated pointwise structures, and enables the design of an algorithm which retrieves the structure directly from the Patterson function, without using error metric minimization.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2023

D-Egg: a dual PMT optical module for IceCube

The D-Egg, an acronym for "Dual optical sensors in an Ellipsoid Glass for Gen2," is one of the optical modules designed for future extensions of the IceCube experiment at the South Pole. The D-Egg has an elongated-sphere shape to maximize the photon-sensitive effective area while maintaining a narrow diameter to reduce the cost and the time needed for drilling of the deployment holes in the glacial ice for the optical modules at depths up to 2700 m. The D-Egg design is utilized for the IceCube Upgrade, the next stage of the IceCube project also known as IceCube-Gen2 Phase 1, where nearly half of the optical sensors to be deployed are D-Eggs. With two 8-inch high-quantum efficiency photomultiplier tubes (PMTs) per module, D-Eggs offer an increased effective area while retaining the successful design of the IceCube digital optical module (DOM). The convolution of the wavelength-dependent effective area and the Cherenkov emission spectrum provides an effective photodetection sensitivity that is 2.8 times larger than that of IceCube DOMs. The signal of each of the two PMTs is digitized using ultra-low-power 14-bit analog-to-digital converters with a sampling frequency of 240 MSPS, enabling a flexible event triggering, as well as seamless and lossless event recording of single-photon signals to multi-photons exceeding 200 photoelectrons within 10 ns. Mass production of D-Eggs has been completed, with 277 out of the 310 D-Eggs produced to be used in the IceCube Upgrade. In this paper, we report the design of the D-Eggs, as well as the sensitivity and the single to multi-photon detection performance of mass-produced D-Eggs measured in a laboratory using the built-in data acquisition system in each D-Egg optical sensor module.

47 OTHER INSTRUMENTATION↗

DOE OSTI2023

AugerPrime surface detector electronics

Operating since 2004, the Pierre Auger Observatory has led to major advances in our understanding of the ultra-high-energy cosmic rays. The latest findings have revealed new insights that led to the upgrade of the Observatory, with the primary goal of obtaining information on the primary mass of the most energetic cosmic rays on a shower-by-shower basis. In the framework of the upgrade, called AugerPrime, the 1660 water-Cherenkov detectors of the surface array are equipped with plastic scintillators and radio antennas, allowing us to enhance the composition sensitivity. To accommodate new detectors and to increase experimental capabilities, the electronics is also upgraded. This includes better timing with up-to-date GPS receivers, higher sampling frequency, increased dynamic range, and more powerful local processing of the data. In this paper, the design characteristics of the new electronics and the enhanced dynamic range will be described. The manufacturing and test processes will be outlined and the test results will be discussed. The calibration of the SD detector and various performance parameters obtained from the analysis of the first commissioning data will also be presented.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2021

DSP Implementation of a Novel Recurrent Neural Network Controller into a TI Solar Microinverter

Single-phase grid-tied inverters are widely used to integrate small-scale renewable energy sources and distributed generations to the utility grid. A novel Recurrent Neural Network (RNN) current controller is introduced to solve the resonant problem associated with LCL based inverters. The well-trained RNN controller was validated through a Texas Instruments (TI) LCL filter based solar microinverter kit that contains a C2000 TI microcontroller. The inverter closed current loop test without the grid connection was conducted in a laboratory setup to verify the RNN contoller functionality. The laboratory waveform results verified that the RNN current controller produced the strong tracking of the measured inverter AC current to its reference value even at a low sampling frequency of 5KHz. The proposed RNN current controller also proved to perform better than the built-in three-pole-three-zero (3P3Z) current controller provided by TI and produce lower values of Total Harmonic Distortion (THD).

digital signal processor↗

DOE OSTI2021

Cloud microphysical structure analysis based on high-resolution insitu measurements

This study investigates the microphysical parameters and shapes of droplet size distributions (DSDs) along three aircraft traverses of developing convective clouds during Cloud Aerosol Interactions and Precipitation Enhancement Experiment (CAIPEEX) Phase III 2015 at a sampling frequency of 25 Hz. The droplet number concentration (Nc, cm -3 ), and liquid water content (LWC, g m -3 ) present steep gradients within zones of a few tens of meters near the cloud edges and relatively gentle gradients in the strong updraft zones. Sometimes, the horizontal LWC distribution resembles a trapezoidal shape with steep LWC and Nc gradients near the cloud edges. The LWC maximums (LWC max ) are lower than the adiabatic LWCs, but the high adiabatic fractions in the cloud core indicate low dilution. High LWC/LWC max , largest droplets, and narrow and similarly shaped DSDs are found in the regions of high updrafts. Zones of low LWC/LWC max are found close to the cloud edges, where DSDs are highly diverse, containing both large and small droplets. Finally, we analyze the mixing diagrams. Significant in-phase turbulent fluctuations in LWC and N c were found. The effective radii change slightly across cloud updraft zones but decrease at the zone of low LWC/LWC max ratio close to cloud edges. The spectra of LWC and N c obey Kolmogorov -5/3 turbulence law. The radii of the correlation of LWC and N c in updraft zones are of several tens of meters. Filaments up to 120–175 m in size are also noticed.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Dimensionally Aligned Signal Projection Algorithms Library

Dimensionally aligned signal projection (DASP) algorithms are used to analyze fast Fourier transforms (FFTs) and generate visualizations that help focus on the harmonics for specific signals. At a high level, these algorithms extract the FFT segments around each harmonic frequency center, and then align them in equally sized arrays ordered by increasing distance from the base frequency. This allows for a focused view of the harmonic frequencies, which, among other use cases, can enable machine learning algorithms to more easily identify salient patterns. This work seeks to provide an effective open-source implementation of the DASP algorithms proposed by Vann et al. (2018) as well as functionality to help explore and test how these algorithms work with an interactive dashboard and signal-generation tool. The DASP library is implemented in Python and contains four types of algorithms for implementing these feature engineering techniques: fixed harmonically aligned signal projection (HASP), decimating HASP, interpolating HASP, and frequency aligned signal projection (FASP). Each algorithm returns a numerical array, which can be visualized as an image. The HASP algorithms are variations of the algorithms originally presented by Vann et al. (2018). For consistency, FASP, which is the terminology used for the short-time Fourier transform (STFT), has been implemented as part of the library to provide a similar interface to the STFT of the raw signal. Additionally, the library contains an algorithm to generate artificial signals with basic customizations such as the base frequency, sample rate, duration, number of harmonics, noise, and number of signals. Finally, the library provides multiple interactive visualizations, each of which is implemented using IPyWidgets and works in a Jupyter environment. A dashboard-style visualization is provided, which contains some common signal-processing visual components (signal, FFT, spectogram) updating in unison with the HASP functions (see Figure 1 below). Separate from the dashboard, an independent visualization is provided for each of the DASP algorithms as well as for the artifical signal generator. These visualizations are included in the library to aid in developing an intuitive understanding how the algorithms are affected by different input signals and parameter selections.

harmonics↗

DOE OSTI2022

Improved Data Interpretation through Identification of Time Series Periodicity Changes

Analysis and interpretation of time series data is easiest when the data values occur at uniform intervals in time, but actual data may have differing data sampling frequencies, such as monthly and daily readings. Applying data analysis techniques, such as smoothing, to such a data set may not give a representative result between time segments. The ability to automatically distinguish time segments of differing data frequency would provide a means for applying data analysis independently to each segment, though a suitable blending at segment boundaries would be required. A method for detecting frequency changes was developed and applied to Gaussian and median smoothing of hydraulic head data from groundwater wells at the U.S. Department of Energy Hanford Site in southeastern Washington state. The process identifies time segments of high-frequency (daily) or low-frequency (greater than daily) data using adjusted-bandwidth Gaussian kernel density estimation and a threshold value, which are further refined to address small blocks of low-frequency data within larger blocks of high-frequency data. User-selectable levels of smoothing are then applied independently to the time segments prior to combining the segment results for a single smoothed data set. This time segment identification approach provides effective low- and high-frequency data separation, which provides a method to apply data analysis independently to each time segment.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

AI-Accelerated Strategies and Solutions in Environmental Technology (AI-ASSET)

ALTEMIS Present Day • An integrated network of different sensing technologies designed to monitor a complex and evolving hydrogeochemical system • Key Concept: Use controlling (proxy) variables measured by sensors to predict plume anomalies before they occur • 80% Reduction in wells • $12-20K/year/well saved • Reduced sampling frequency • But how did we get here?

De La Noval, Alejandro J. [Savannah River National↗

DOE OSTI2025

Data-Driven Method for Groundwater-Level Mapping and Monitoring-Well Network Optimization at Hanford

This report summarizes the initial results and outcomes of a physics-informed, data-driven groundwater level (GWL) mapping capability for the Hanford Site. GWL mapping at Hanford is typically conducted annually and requires a significant amount of computational and expert resources, and it does not allow assessment of the informational value of specific monitoring wells. The proposed method produces spatially and temporally resolved fields consistent with sparse, irregularly sampled, and nonuniformly distributed well measurements. Implemented successfully, this capability will allow rapid mapping of groundwater levels and provide an opportunity to optimize monitoring activities (both location and sampling frequency) based on data information value evaluation. The approach integrates a diffusion-based generative model – trained on MODFLOW simulation data from the Plateau-to-River (P2R) model – with score-based data assimilation (SDA), allowing observation-conditioned mapping without retraining for each monitoring-network layout.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Marine renewable energy for Arctic observations

Arctic observations are becoming increasingly valuable as researchers investigate climate change and its associated concerns, such as decreasing sea ice and increasing ship traffic. Networks of sensors with frequent sampling capabilities are needed to run forecast models, improve navigation, and inform climate research. Sampling frequency and deployment duration are currently constrained by battery power limitations. In-situ power generation using marine renewable energy sources such as waves and currents can be used to circumvent this constraint. Wave and current resources vary spatially and temporally in the Arctic, with some locations and seasons being better suited for marine renewable energy power generation. Locations and seasons with small resources may still be able to use marine renewable energy because of the low power requirements of the instruments. In this study, we describe the wave and current resources in the Arctic, outline the electricity generation developments that are needed to utilize the resources, and suggest use cases. Wave and current energy converters developed to power observations in the Arctic could also be used to power observations at lower latitudes. Marine renewable energy has the potential to decrease dependence on batteries and improve data collection capabilities in the Arctic; however, this would require the development of new low power technologies that can operate in extreme Arctic environments.

16 TIDAL AND WAVE POWER↗

DOE OSTI2021

A differential emissivity imaging technique for measuring hydrometeor mass and type

Abstract. The Differential Emissivity Imaging Disdrometer (DEID) is a new evaporation-based optical and thermal instrument designed to measure the mass, size, density and type of individual hydrometeors as well as their bulk properties. Hydrometeor spatial dimensions are measured on a heated metal plate using an infrared camera by exploiting the much higher thermal emissivity of water compared with metal. As a melted hydrometeor evaporates, its mass can be directly related to the loss of heat from the hotplate assuming energy conservation across the hydrometeor. The heat loss required to evaporate a hydrometeor is found to be independent of environmental conditions including ambient wind velocity, moisture level and temperature. The difference in heat loss for snow vs. rain for a given mass offers a method for discriminating precipitation phase. The DEID measures hydrometeors at sampling frequencies of up to 1 Hz with masses and effective diameters greater than 1 µg and 200 µm, respectively, determined by the size of the hotplate and the thermal camera specifications. Measurable snow water equivalent (SWE) precipitation rates range from 0.001 to 200 mm h−1, as validated against a standard weighing bucket. Preliminary field experiment measurements of snow and rain from the winters of 2019 and 2020 provided continuous automated measurements of precipitation rate, snow density and visibility. Measured hydrometeor size distributions agree well with canonical results described in the literature.

47 OTHER INSTRUMENTATION↗

DOE OSTI2024

TROPOS pyranometer network (PyrNet) observational data set collected during the S2VSR field campaign

During the Small-Scale Variability of Solar Radiation field campaign (S2VSR), a unique sensor network consisting of 60 autonomous pyranometer stations was deployed for a 12-week period at the ARM Southern Great Plains observatory. Stations have been distributed across a 4x4 to 6x6 km2 domain surrounding the Central Facility. Each station has recorded global radiation together with air temperature and relative humidity with a sampling frequency of 1-Hz. The network has provided a data set with an unprecedented level of detail of the small-scale variability of global solar radiation at the surface, resolving fluctuations down to the second- and decameter-scale.

54 ENVIRONMENTAL SCIENCES↗