Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shockwaves”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Analysis of nonequilibrium molecular nitrogen ultraviolet radiation in pure N2 shockwaves

An analysis of data previously reported from a test series in the Electric Arc Shock Tube Facility for incident shocks composed of pure Nitrogen was performed. The present work focuses on the lowest velocity measured in the test (approximately 7 km/s) where molecular radiation is significant. Analysis of the spectral data with the NEQAIR radiative transport code obtains post-shock trends in temperature and number densities of the states of N2. The results suggest that chemical, and possibly thermal, equilibrium has not been obtained within the distance/time measured (about 5 cm/120 ms). In the nonequilibrium region of the shock, differences between rotational temperatures of different species are observed, as well as differences between rotational and vibrational temperatures. Population of rotational states above the dissociation limit is observed to occur over a distance of several cm. Finally, these data suggest that predissociation strongly affects the C^3 Π_u state of N2, leading to a lower measured radiation than predicted. An effective average pre-dissociation rate is shown to produce reasonable agreement under quasi-steady state approximation.

Augustin Tibere-Inglesse↗
NASA NTRSDate not supplied

Analysis of the Amplitude Response of a Two-Point and a Multi-Point Focused Laser Differential Interferometer

Experiments were performed with two different focused laser differential interferometer (FLDI) instruments to assess the relative amplitude response of each instrument to a traveling shockwave generated by a laser spark in air. The first FLDI instrument generated two slightly-separated measurement points, with each measurement point providing sensitivity to density fluctuations induced by the shockwave. By performing a cross-correlation between the signals obtained from each measurement point, the phase velocity of density fluctuations can be obtained. The second FLDI instrument generated a measurement line that was oriented parallel to the shockwave direction of travel with the resulting interference pattern sampled at multiple equally-spaced points along the line. As a result, this instrument provides density fluctuation measurement capability at multiple points simultaneously. When the measurement line is oriented parallel to the shockwave direction of travel, the phase velocity, rate of change of the phase velocity, and acceleration of density fluctuations traveling along each line can be obtained by performing a cross-correlation between points along the line. Numerical computations of the shockwave generated by the laser spark are used to simulate the response of each instrument and are compared to the experimental results. High-speed schlieren imaging has also been performed and is compared with the FLDI measurements and computational results.

Interferometry↗
NASA NTRSDate not supplied

Analysis of the Amplitude Response of a Two-Point and a Two-Line/Multi-Point Focused Laser Differential Interferometer

Experiments were performed with two different focused laser differential interferometer (FLDI) instruments to assess the amplitude response of each instrument to a traveling shock-wave generated by a laser spark. The first FLDI instrument generated two measurement points, with each measurement point providing sensitivity to density fluctuations induced by the shockwave. By performing a cross-correlation between the signals obtained from each measurement point, the phase velocity of density fluctuations can be obtained. The second FLDI instrument generated two measurement lines that are oriented either parallel or orthogonal to the shockwave direction of travel with the resulting interference pattern sampled at multiple equally-spaced points along each line. As a result, this instrument provides density fluctuation measurement capability at multiple points simultaneously. When the measurement lines are oriented parallel to the shockwave direction of travel, the phase velocity, rate of change of the phase velocity, and acceleration of density fluctuations traveling along each line can be obtained by performing a cross-correlation between points along a single line. When the measurement lines are oriented orthogonal to the shockwave direction of travel, the spatially-varying phase velocity can be obtained by performing a cross-correlation between points at the same relative location on each measurement line. Computations of the shockwave generated by the laser spark are used to simulate the response of each instrument and are compared to the experimental results. High-speed Schlieren imaging has also been performed and is compared with the FLDI measurements and computational results.

Focused Laser Differential Interferometer↗
NASA NTRSDate not supplied

Analysis of the Amplitude Response of a Two-Point and a Multi-Point Focused Laser Differential Interferometer

Experiments were performed with two different focused laser differential interferometer (FLDI) instruments to assess the relative amplitude response of each instrument to a traveling shockwave generated by a laser spark in air. The first FLDI instrument generated two slightly-separated measurement points, with each measurement point providing sensitivity to density fluctuations induced by the shockwave. By performing a cross-correlation between the signals obtained from each measurement point, the phase velocity of density fluctuations can be obtained. The second FLDI instrument generated a measurement line that was oriented parallel to the shockwave direction of travel with the resulting interference pattern sampled at multiple equally-spaced points along the line. As a result, this instrument provides density fluctuation measurement capability at multiple points simultaneously. When the measurement line is oriented parallel to the shockwave direction of travel, the phase velocity, rate of change of the phase velocity, and acceleration of density fluctuations traveling along each line can be obtained by performing a cross-correlation between points along the line. Numerical computations of the shockwave generated by the laser spark are used to simulate the response of each instrument and are compared to the experimental results. High-speed schlieren imaging has also been performed and is compared with the FLDI measurements and computational results.

Brett F. Bathel↗
NASA NTRS1988

Navier-Stokes structure of merged layer flow on the spherical nose of a space vehicle

Hypersonic merged layer flow on the forepart of a spherical surface of a space vehicle has been investigated on the basis of the full steady-state Navier-Stokes equations using slip and temperature jump boundary conditions at the surface and free-stream conditions far from the surface. The shockwave-like structure was determined as part of the computations. Using an equivalent body concept, computations were carried out under conditions that the Aeroassist Flight Experiment (AFE) Vehicle would encounter at 15 and 20 seconds in its flight path. Emphasis was placed on understanding the basic nature of the flow structure under low density conditions. Particular attention was paid to the understanding of the structure of the outer shockwave-like region as the fluid expands around the sphere. Plots were drawn for flow profiles and surface characteristics to understand the role of dissipation processes in the merged layer of the spherical nose of the vehicle.

Jain, A. C.↗
NASA NTRS1997

Cratering on Titan: A Pre-Cassini Perspective

The NASA-ESA Cassini mission, comprising a formidably instrumented orbiter and parachute-borne probe to be launched this October, promises to reveal a crater population on Titan that has been heretofore hidden by atmospheric haze. This population on the largest remaining unexplored surface in the solar system will be invaluable in comparative planetological studies, since it introduces evidence of the atmospheric effects of cratering on an icy satellite. Here, I highlight some impact features we may hope to find and could devote some modeling effort toward. Titan in a Nutshell: Radius= 2575 km. Density= 1880 kg/cubic m consistent with rock-ice composition. Surface pressure = 1.5 bar. Surface gravity = 1.35 m/square s Atmosphere -94% N2 6% CH, Surface temperature = 94K Tropopause temperature = 70K at 40 km alt. Probable liquid hydrocarbon deposits exist on or near the surface.Titan in a Nutshell: Radius= 2575 km. Density= 1880 kg/cubic m consistent with rock-ice composition. Surface pressure = 1.5 bar. Surface gravity = 1.35 m/square s; Atmosphere about 94% N2 6% CH, Surface temperature = 94K Tropopause temperature = 70K at 40 km alt. Probable liquid hydrocarbon deposits exist on or near the surface. Titan is comparable to Callisto and Ganymede for strength/gravity, Mars/Earth/Venus for atmospheric interaction, and Hyperion, Rhea, and Iapetus for impactor distribution. The leading/trailing asymmetry of crater density from heliocentric impactors is expected to be about 5-6, in the absence of resurfacing. Any Saturnocentric impactor population is likely to alter this. In particular the impact disruption of Hyperion is noted; because of the 3:4 orbital resonance with Titan, fragments from the proto-Hyperion breakup would have rapidly accreted onto Titan. Titan's resurfacing history is of course unknown. The disruption of impactors into fragments that individually create small craters is expected to occur. A crude estimate suggests a maximum separation of about 2 km (compared with 4 km on Venus, or 0.5 km on Earth). Crater chains are unlikely on Titan, since impactors must pass close enough to Saturn to be tidally disrupted; as a result, they would suffer aerodynamic disruption. Crater counting on adjacent satellites gives densities of about 200 per 10 (exp 6) square km for 20-km-diameter craters. However, the presence of a thick atmosphere leads to atmospheric shielding, depleting the relative abundance of small craters. This has been evaluated by models, and the relative abundance of small craters may be due to a diagnostic atmospheric collapse. A number of radar-dark "splotches" have been detected on Venus; these have been attributed to the interaction of the surface with the atmospheric shockwave produced by the Tunguska-like explosion of a bolide in the atmosphere. Simple analogy suggests that similar features might occur on Titan, but the shocked mass density (which controls the momentum coupling between the surface and the shockwave) of Titan's cold N2 atmosphere is about 20x smaller than that of Venus's hot CO2 atmosphere. Unless ice is much more easily turned to rubble than is rock, such features seem less probable on Titan. When the energy deposited by an impact forms a fireball with an equilibrate greater than one scale height, the fireball expands upward and can distribute ejecta. on ballistic exoatmospheric trajectories. On Venus this process is believed to be responsible for the parabolic features; the interaction of various-sized particles falling through the atmosphere with the zonal wind field winnows the particles to form a parabolic deposit. Although such a process is possible on Titan, the large scale height at higher altitudes would make it more difficult. Comparison with craters on other icy satellites suggests that craters on Titan will be fairly shallow (depth/diameter about 0.1) and craters greater than 10 km in diameter will have central peaks or domed bases, perhaps with central pits. The formation of ejecta. blankets may involve the atmosphere in a significant way, both by restraining the expansion of the ejecta cloud and by influencing the thermal history of the ejecta. Compared with Venus, Titan's atmosphere will chill an impact melt somewhat quickly, so the long ejecta flows seen on Venus seem less likely, detailed modeling needs to be performed to determine the impact melt production. Crater topography on Titan may be highlighted by the influence of liquids forming crater lakes. Craters with central peaks will typically form ring-shaped lakes, although horseshoe-shaped takes may be common; domed craters with central pits may even form bullseye lakes with islands with central ponds. If liquids have covered a substantial part of Titan's surface for a substantial period, hydroblemes and tsunami deposits may be common.

Lorenz, R. D.↗
NASA NTRS2011

Panchromatic Observations of SN2011dh Point to a Compact Progenitor Star

We report the discovery and detailed monitoring of X-ray emission associated with the Type IIb SN2011dh using data from the Swift and Chandra satellites, placing it among the best studied X-ray supernovae to date. We further present millimeter and radio data obtained with the SMA, CARMA, and EVLA during the first three weeks after explosion. Combining these observations with early optical photometry, we show that the panchromatic dataset is well-described by non-thermal synchrotron emission (radio/mm) with inverse Compton scattering (X-ray) of a thermal population of optical photons. We derive the properties of the shockwave and the circumstellar environment and find a time-averaged shock velocity of v approximately equals 0.1c and a progenitor mass loss rate of M-dot approximately equals 6 X 10 (exp 5) Solar M/ yr (wind velocity, v(sub w) = 1000 km/s). We show that these properties are consistent with the sub-class of Type IIb supernovae characterized by compact progenitors (Type cIIb) and dissimilar from those with extended progenitors (Type eIIb). Furthermore, we consider the early optical emission in the context of a cooling envelope model to estimate a progenitor radius of R(sub star) approximately equals 10(exp 11) cm, in line with the expectations for a Type cIIb supernova. Together, these diagnostics suggest that the putative yellow supergiant progenitor star identified in archival HST observations is instead a binary companion or unrelated to the supernova. Finally, we searched for the high energy shock breakout pulse using X-ray and gamma-ray observations obtained during the purported explosion date range. Based on the compact radius of the progenitor, we estimate that the shock breakout pulse was detectable with current instruments but likely missed due to their limited temporal/ spatial coverage. Future all-sky missions will regularly detect shock breakout emission from compact SN progenitors enabling prompt follow-up observations of the shockwave with the EVLA and ALMA.

Soderberg, A. M.↗
NASA NTRS2022

Design of Hypervelocity Flow Generator (HFG) and Its Diagnostics

Ground facilities for hypersonic research are a key element for successful development of aerodynamically proven hypervelocity vehicles. Design concepts and diagnostics of a hypervelocity flow generator (HFG) were made as a test platform for hypersonic/hypervelocity spacecraft models at the NASA Langley Research Center. The HFG is a hypersonic flow field generator using optically heated gas which is blown into an 80 cu m vacuum chamber. The vacuum chamber is kept at a stable vacuum pressure with a combination of three large vacuum pumps, while the HFG is in the test mode. The HFG provides a relatively small test section with approximately a 20 cm window. This facility was designed to generate 2.45 km/sec of flow speed, and potentially generate a continuous flow with the nozzle and vacuum system. The window in test section provides a direct view of the shock wave around a model in order to measure temperature, pressure, and density profile within the shock layer. One of the key test goals under this project is to understand why the emission spectra from the standing shockwave plasma predicted by Lora-Loran codes are significantly different from the measured emission spectra from the Flight Investigation Reentry Environment (FIRE II) Flight. The correct estimate of the thermal loading on the leading edge of hypersonic vehicles greatly affects the aerodynamic design, the material selection for the vehicle, and the cooling requirement and can be obtained by the precise modeling of emission spectra from shockwave plasma. However, the estimation of thermal loading is not an easy task due to complex non-equilibrium radiative process within high temperature shock layers that still falls into a category of cold plasma. Direct flight experiments are the most desirable, but not a cost-effective approach. Analysis by computational fluid dynamics (CFD) offers many test flexibilities. However, the CFD codes must be fully tested and validated with experimental data before the codes are effectively used for practical design. Large discrepancies between experiments and codes appear in hypersonic/hypervelocity flow regimes at high altitudes of 60 km ~ 90 km. This HFG facility offers some important parameters for CFD code validation, such as collision cross-sections, relaxation times, reaction rate coefficients and transportation coefficients. The HFG test facility is based on the ejection flow of high temperature gas heated over to 3500 K through a nozzle. The tungsten gas chamber of the HFG is heated up to a desired temperature by a 60 kW optical power beam source. This system consists of an optical power source, a thermal chamber, an expansion nozzle, a test section, and an 80 cu m vacuum tank. 60 kW optical input power is obtained from the 150 kW Vortek arc lamp system (by Vortek Industries, Vancouver, Canada). This optical beam is focused to heat the gas chamber within which a flow media is heated. The maximum achievable temperature of the flow medium reached approximately 3500 K or even higher but is limited by the melting point of the chamber material used. The exhaust velocity through the nozzle was determined by the stagnation temperature and the molecular weight of the working medium at the test section. To provide design parameters, a NASA Chemical Equilibrium with Application (CEA) computer program is used for the simulation of aerothermal data. This CEA program can calculate chemical equilibrium and properties of complex mixtures using shock tube parameters. For nitrogen gas at 2666 K stagnation temperature, the maximum achievable velocity at the test section is approximately 2.45 km/sec which is within the range of the thermal velocity of 8000 K shock layer. Based on the calculation through the CEA program, the design parameters of a HFG were determined and implemented for the test section that includes an expansion nozzle. The installed test section of the experimental facility can sustain a condition of a re-entry vehicle from the Space at an altitude of 60-90 km. After installation of the HFG, the system was fully tested and its operational parameters were measured. An 80 cu m vacuum chamber of HFG was set at 1 torr level to keep a stable downstream condition. The pumping time to reach the minimum vacuum pressure (~ 1 torr) at the test chamber from atmospheric pressure was approximately an hour using Kinney (MBV-14000/MB -1600/KT-300) and Stokes (Model 1772 and 412) pumps. Such a setup condition allowed a continued stable operation of the HFG experiment with flowrates through 1-, 3-, or 5-mm diameters of nozzle throat. The flow characteristics of the HFG for various operating conditions were performed using a focused Schlieren method. At 0.8 torr chamber pressure, a barrel shock was observed at the test section. With a sphere obstacle of 12 mm diameter in the flow, a bow shock (~ 2-mm thickness) was observed by a focused Schlieren visualization method.

Hypervelocity flow↗
NASA NTRS1993

(abstract) Supernova Remnant and Molecular Clouds

Upon impact of the shockwaves generated by a supernova remnant, molecular gas and the associated dust grains are substantially excited and become prominent sources of infrared emission. Recent studies of such interactions, utilizing the infrared data and information from other wavelengths, have revealed many details of the physical processes in the interstellar medium. In particluar, the understanding of the temperature and ionization structures in the postshock material is helpful in modeling the star-gas cycles in the Galaxy, and probing the circumstances of star formation.

medium molecular gas↗
NASA NTRS2020

1- by 1-Foot Supersonic Wind Tunnel Sidewall Flowfield Compression Plate Study

A method for locally increasing the dynamic pressure in the test section of a supersonic wind tunnel is investigated from a theoretical, computational and experimental perspective, culminating in a reduced-scale, proof-of-concept test at Mach 3.44. Symmetric, variable-angle compression plates along the test section sidewalls generate oblique shockwaves to elevate the test section dynamic pressure (q). The experimental effort utilizes boundary-layer pitot rakes to sample the incoming flow near the floor, pitot and static rakes to measure the high-q core flow and numerous surface taps to map out the static pressure distribution along the floor, ceiling and sidewalls. A reliable and robust starting procedure is developed to establish supersonic flow in the test section and behind the compression plates. A characterization of the incoming floor boundary layer reveals previously documented features (such as a bulge toward the centerline) and an unexpected (and as-yet-unexplained) thickening of the boundary layer with increasing Reynolds number around total pressures of 40–60 psia. The high-q core flow is characterized for eight compression plate angles (4.0–8.0°), eight tunnel total pressures (20–139 psia) and three axial stations (24.95–27.35 inches). The peak dynamic pressure rise exceeds expectations. At conditions relevant to full-scale testing (6.0° and 139 psia), the dynamic pressure increases by a factor of 1.73, the Mach number becomes 2.85 and the total pressure drops imperceptibly. Basic distortion metrics show transverse non-uniformity of less than 5 %. Limited spatial resolution in the static rake measurements warrants additional, higher fidelity testing or computational analysis. Surface-mounted, fast-response instrumentation suggests minimal unsteadiness in the flow, less than a few percent of the mean (comparable to the sensor accuracy).

Wind tunnel testing, test techniques/methods, dyna↗
NASA NTRSDate not supplied

Hybrid pulse-burst / cross-correlation DGV for high-speed flow measurements at 100 kHz

Hybrid pulse-burst Doppler global velocimetry (PB-DGV)/pulse-burst, cross-correlation DGV (PB-CC-DGV) was demonstrated for the first time in the NASA Langley 4-foot Supersonic Unitary Plan Wind Tunnel, allowing simultaneous acquisition of mean and instantaneous high-repetition-rate velocity fields. The technique was used to make planar velocity measurements across an oblique shockwave generated by a large splitter plate set at a -2° angle of attack in a Mach 2.4 flow. Sequences of more than 100 consecutive instantaneous velocity images were obtained at a rate of 100 kHz. Velocity fields from both aspects of the hybrid measurement indicated errors less than 1-percent of anticipated velocities. Likewise, all assessments of measurement precision were approximately 1.6-percent of the local velocities. Additional demonstrations in different flowfields including a subsonic axi-symmetric jet and a supersonic Mars reentry vehicle model further illustrate the utility of the new hybrid method.

laser↗
NASA NTRS1963

Effects of Mass Addition on the Stability of Slender Cones at Hypersonic Speeds

The effect of mass addition on the flow over bodies moving at hypersonic speeds has been studied by several investigators (e.g., Cresci and Libby). In most of this work, primary attention logically has been directed toward the effects of foreign-gas injection on heat transfer and pressure distributions, and, principally for this reason, most of the work ha been done at zero angle of attack. The foreign gas can be provided either by some active injection system or by the action of an ablation heat shield. With increasing rates of injection, the basic flow about the body can be affected significantly. One such effect was observed in the paper by Cresci and Libby, where it was shown that the shockwave standoff distance can be increased by gas injection at the nose of a body.

SLENDER BODY↗
NASA NTRS1972

Calculation of heat transfer on shuttle type configurations including the effects of variable entropy at boundary layer edge

A relatively simple method is presented for including the effect of variable entropy at the boundary-layer edge in a heat transfer method developed previously. For each inviscid surface streamline an approximate shockwave shape is calculated using a modified form of Maslen's method for inviscid axisymmetric flows. The entropy for the streamline at the edge of the boundary layer is determined by equating the mass flux through the shock wave to that inside the boundary layer. Approximations used in this technique allow the heating rates along each inviscid surface streamline to be calculated independent of the other streamlines. The shock standoff distances computed by the present method are found to compare well with those computed by Maslen's asymmetric method. Heating rates are presented for blunted circular and elliptical cones and a typical space shuttle orbiter at angles of attack. Variable entropy effects are found to increase heating rates downstream of the nose significantly higher than those computed using normal-shock entropy, and turbulent heating rates increased more than laminar rates. Effects of Reynolds number and angles of attack are also shown.

Dejarnette, F. R.↗
NASA NTRS1973

Analysis of SRM model nozzle calibration test data in support of IA12B, IA12C and IA36 space shuttle launch vehicle aerodynamics tests

Variations of nozzle performance characteristics of the model nozzles used in the Space Shuttle IA12B, IA12C, IA36 power-on launch vehicle test series are shown by comparison between experimental and analytical data. The experimental data are nozzle wall pressure distributions and schlieren photographs of the exhaust plume shapes. The exhaust plume shapes were simulated experimentally with cold flow while the analytical data were generated using a method-of-characteristics solution. Exhaust plume boundaries, boundary shockwave locations and nozzle wall pressure measurements calculated analytically agree favorably with the experimental data from the IA12C and IA36 test series. For the IA12B test series condensation was suspected in the exhaust plumes at the higher pressure ratios required to simulate the prototype plume shapes. Nozzle calibration tests for the series were conducted at pressure ratios where condensation either did not occur or if present did not produce a noticeable effect on the plume shapes. However, at the pressure ratios required in the power-on launch vehicle tests condensation probably occurs and could significantly affect the exhaust plume shapes.

Baker, L. R., Jr.↗
NASA NTRS1975

A comparison of a shock-capturing technique with experimental data for three-dimensional internal flows

Shock-capturing solutions for an axisymmetric supersonic inlet at small angles of attack are obtained. Good overall agreement between the shock-capturing solutions and experimental data is shown except in regions of strong viscous effects or boundary-layer removal. Although the results indicate a strong potential for the use of shock-capturing or finite-difference solutions for internal flows, improvement in the ability to handle the reflection of strong shockwaves having downstream Mach numbers near 1 is needed.

Presley, L. L.↗
NASA NTRS1975

Supersonic inlet contour interpolation

A method for designing supersonic inlet contours is described which consists in the interpolation of the contours of two known inlets designed for different Mach numbers, thereby determining the contours for a third inlet at an intermediate design Mach number. Several similar axisymmetric inlet contours were interpolated from known inlets with design Mach numbers ranging from 2.16 to 4.0 and with design Mach numbers differing by as much as 1.0. The flowfields were calculated according to Sorensen's (1965) computer program. Shockwave structure and pressure distribution characteristics are shown for the interpolated inlets. The validity of the interpolation is demonstrated by comparing the plots of the flowfield properties across the throat station of the interpolated inlet with the known inlets which were designed iteratively. It seems possible to write a computer program so that a matrix of known inlet contours can be interpolated.

Sorensen, N. E.↗
NASA NTRS1980

An alternating-direction-implicit algorithm for the unsteady potential equation in conservation form

An implicit finite difference scheme for an efficient computation of unsteady potential flow about airfoils is presented. The formulation uses density and velocity potential as dependent variables, and is cast in conservation form to assure the theoretically correct determination of shockwave location and speed. To enable boundary conditions to be imposed directly on the airfoil surface, a time varying sheared rectilinear coordinate transformation is employed. Calculated time history solutions on a pulsating airfoil are compared with the results of another unsteady transonic code. It is concluded that the method has excellent numerical stability and gives accurate solutions with sharply resolved shocks.

Chipman, R. R.↗
NASA NTRS1981

An alternating-direction implicit algorithm for unsteady potential flow

An implicit finite-difference scheme is presented for the efficient computation of unsteady potential flow about airfoils. The formulation uses density and the velocity potential as dependent variables and is cast in conservation form to assure the theoretically correct determination of shockwave location and speed. To enable boundary conditions to be imposed directly on the airfoil surface, a time-varying sheared-rectilinear coordinate transformation is employed. Calculated time-history solutions on a pulsating airfoil are compared with the results of other unsteady transonic codes, including a previous method of the authors. The present method is demonstrated to be unconditionally stable and to give accurate solutions with sharply resolved shocks.

Chipman, R.↗