Search NASA⌕ Search

SEARCH · Search NASA

Results for “Skin friction coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Similarity solution to three dimensional boundary layer flow of second grade nanofluid past a stretching surface with thermal radiation and heat source/sink

Development of human society greatly depends upon solar energy. Heat, electricity and water from nature can be obtained through solar power. Sustainable energy generation at present is a critical issue in human society development. Solar energy is regarded one of the best sources of renewable energy. Hence the purpose of present study is to construct a model for radiative effects in three-dimensional of nanofluid. Flow of second grade fluid by an exponentially stretching surface is considered. Thermophoresis and Brownian motion effects are taken into account in presence of heat source/sink and chemical reaction. Results are derived for the dimensionless velocities, temperature and concentration. Graphs are plotted to examine the impacts of physical parameters on the temperature and concentration. Numerical computations are presented to examine the values of skin-friction coefficients, Nusselt and Sherwood numbers. It is observed that the values of skin-friction coefficients are more for larger values of second grade parameter. Moreover the radiative effects on the temperature and concentration are quite reverse.

36 MATERIALS SCIENCE↗

A Large-Eddy Simulation Of Turbulent Flow Over A Backward Facing Step

Large-eddy simulation (LES) was used to study the turbulent flow over a backward facing step. The simulations examine the details of the turbulent flow’s separated and reattaching regions created by the step geometry. An explicit high-order of accuracy/high resolution finite-difference computational fluid dynamics solver was used for both LES and Reynolds-averaged Navier-Stokes (RANS) simulations. The experimental data from the backward facing step experiment of Driver and Seegmiller was used for comparison. Data presented are derived from a RANS simulation using the Spalart-Allmaras turbulence model and LES simulations using the implicit LES assumption on three different grids of varying resolution. The RANS solution agrees with past work. It does an adequate job of predicting the flowfield and reattachment point, but misses details such as the strength of the recirculating region and magnitudes of the Reynolds stresses. The synthetic eddy method was used to provide a turbulent inflow to the quasi-2D LES domains. For the LES, the coarse grid was of insufficient resolution and under-predicted the skin friction coefficient and over-predicted the normal stresses. The finer grid LES results accurately predict the skin friction coefficient and provide more accurate Reynolds stresses. Triple product velocity correlations are also computed from the LES and the finer grid results did a good job predicting the magnitudes of the curves and the shapes were reasonably represented. It is recommended that future work include investigating the turbulent inflow domain length, width of the quasi-2D domain, and additional grid refinement

turbulence↗

A Large-Eddy Simulation Of Turbulent Flow Over A Backward Facing Step

Large-eddy simulation (LES) was used to study the turbulent flow over a backward facing step. The simulations examine the details of the turbulent flow's separated and reattaching regions created by the step geometry. An explicit high-order of accuracy/high resolution finite-difference computational fluid dynamics solver was used for both LES and Reynolds-averaged Navier-Stokes (RANS) simulations. The experimental data from the backward facing step experiment of Driver and Seegmiller was used for comparison. Data presented are derived from a RANS simulation using the Spalart-Allmaras turbulence model and LES simulations using the implict LES assumption on three different grids of varying resolution. The RANS solution agrees with past work. It does an adequate job of predicting the flowfield and reattachment point, but misses details such as the strength of the recirculating region and magnitudes of the Reynolds stresses. The synthetic eddy method was used to provide a turbulent inflow to the quasi-2D LES domains. For the LES, the coarse grid was of insufficient resolution and under-predicted the skin friction coefficient and over-predicted the normal stresses. The finer grid LES results accurately predict the skin friction coefficient and provide more accurate Reynolds stresses. Triple product velocity correlations are also computed from the LES and the finer grid results did a good job predicting the magnitudes of the curves and the shapes were reasonably represented. It is recommended that future work include investigating the turbulent inflow domain length, width of the quasi-2D domain, and additional grid refinement.

turbulence↗

Direct Measurements of Skin Friction

A device has been developed to measure local skin friction on a flat plate by measuring the force exerted upon a very small movable part of the surface of the flat plate. These forces, which range from about 1 milligram to about 100 milligrams, are measured by means of a reactance device. The apparatus was first applied to measurements in the low-speed range, both for laminar and turbulent boundary layers. The measured skin-friction coefficients show excellent agreement with Blasius' and Von Karman's results. The device was then applied to high-speed subsonic flow and the turbulent-skin-friction coefficients were determined up to a Mach number of about 0.8. A few measurements in supersonic flow were also made. This paper describes the design and construction of the device and the results of the measurements.

Dhawan, Satish↗

Implementation of wall boundary conditions for transpiration in F3D thin-layer Navier-Stokes code

Numerical boundary conditions for mass injection/suction at the wall are incorporated in the thin-layer Navier-Stokes code, F3D. The accuracy of the boundary conditions and the code is assessed by a detailed comparison of the predictions of velocity distributions and skin-friction coefficients with exact similarity solutions for laminar flow over a flat plate with variable blowing/suction, and measurements for turbulent flow past a flat plate with uniform blowing. In laminar flow, F3D predictions for friction coefficient compare well with exact similarity solution with and without suction, but produces large errors at moderate-to-large values of blowing. A slight Mach number dependence of skin-friction coefficient due to blowing in turbulent flow is computed by F3D code. Predicted surface pressures for turbulent flow past an airfoil with mass injection are in qualitative agreement with measurements for a flat plate.

Kandula, M.↗

Modeling and analysis of mixed convection stagnation point flow of nanofluid towards a stretching surface: OHAM and FEM approach

A theoretical study of mixed convection stagnation point flow towards a stretching surface is presented. The governing boundary layer equations are transformed into a set of highly nonlinear ordinary differential equations using suitable similarity transforms. The semi-analytical solution is obtained using optimal homotopy analysis method (OHAM) and the numerical solution is obtained via finite element method (FEM). Solutions obtained via two different approaches are in excellent agreement, which validates the accuracy of present analysis. In a special case, the present OHAM solution is also validated with the earlier available results. Effect of pertinent flow parameters on the skin friction coefficient and Nusselt number is presented in tabular form, whereas the velocity, temperature and nanoparticle distribution are presented in graphical forms. Further, a quadratic multiple regression analysis on numeric data of skin friction coefficient and Nusselt number is performed. The findings suggest that velocity slip assists the fluid motion in presence of buoyancy forces, whereas it exhibits a retarding nature on fluid motion when no buoyancy forces exist.

97 MATHEMATICS AND COMPUTING↗

Experiments on supersonic turbulent flow development in a square duct

The nature of supersonic, turbulent, adiabatic-wall flow in a square duct is investigated experimentally over a development length of x/D between 0 and 20 for a uniform flow, Mach 3.9 condition at the duct inlet. Initial discussion centers on the duct configuration itself, which was designed specifically to minimize wave effects and nozzle-induced distortion in the flow. Total pressure contours and local skin friction coefficient distributions are presented which show that the flow develops in a manner similar to that observed for the incompressible case. In particular, undulations exist in total pressure contours within the cross plane and in transverse skin friction coefficient distributions, which are indicative of the presence of a well-defined secondary flow superimposed upon the primary flow. The results are analyzed to show that local law-of-the-wall behavior extends well into the corner region, which implies that wall functions conventionally applied in two-equation type turbulence models, when suitably defined for compressible flow, may also be applied to supersonic streamwise corner flows.

Gessner, F. B.↗

Skin-Friction Measurements in Incompressible Flow

Experiments have been conducted to measure the local surface-shear stress and the average skin-friction coefficient in Incompressible flow for a turbulent boundary layer on a smooth flat plate having zero pressure gradient. Data were obtained for a range of Reynolds numbers from 1 million to 45 million. The local surface-shear stress was measured by a floating-element skin-friction balance and also by a calibrated total head tube located on the surface of the test wall. The average skin-friction coefficient was obtained from boundary-layer velocity profiles.

Smith, Donald W.↗

Skin Friction at Very High Reynolds Numbers in the National Transonic Facility

Skin friction coefficients were derived from measurements using standard measurement technologies on an axisymmetric cylinder in the NASA Langley National Transonic Facility (NTF) at Mach numbers from 0.2 to 0.85. The pressure gradient was nominally zero, the wall temperature was nominally adiabatic, and the ratio of boundary layer thickness to model diameter within the measurement region was 0.10 to 0.14, varying with distance along the model. Reynolds numbers based on momentum thicknesses ranged from 37,000 to 605,000. The measurements approximately doubled the range of available data for flat plate skin friction coefficients. Three different techniques were used to measure surface shear. The maximum error of Preston tube measurements was estimated to be 2.5 percent, while that of Clauser derived measurements was estimated to be approximately 5 percent. Direct measurements by skin friction balance proved to be subject to large errors and were not considered reliable.

Watson, Ralph D.↗

Performance of large-eddy breakup devices at post-transitional Reynolds numbers

Large-eddy alteration techniques were used to modify the drag characteristics of the turbulent boundary layer. Local skin-friction coefficients were measured for single and multi-element arrays of thin plates suspended in a fully turbulent, flat plate, boundary layer at R(theta) = 3,000. Effects of these devices were measured more than 300 boundary-layer thicknesses downstream to R(theta) = 17,000. It was found that although most of the devices reduced the local skin friction immediately downstream, this reduced skin-friction region persisted for only 100-120 delta-0, after which a rapid rise in skin-friction coefficient occurred, often exceeding flat plate values. Net drag reductions were obtained only for tandem configurations and these reductions were sensitive to device spacing and height. The maximum net drag reduction reported was approximately 7 percent with a device spacing of 10 delta-0 at a height of 0.8 delta-0.

Anders, J. B.↗

Heat and mass transfer rates during flow of dissociated hydrogen gas over graphite surface

To improve upon the performance of chemical rockets, the nuclear reactor has been applied to a rocket propulsion system using hydrogen gas as working fluid and a graphite-composite forming a part of the structure. Under the boundary layer approximation, theoretical predictions of skin friction coefficient, surface heat transfer rate and surface regression rate have been made for laminar/turbulent dissociated hydrogen gas flowing over a flat graphite surface. The external stream is assumed to be frozen. The analysis is restricted to Mach numbers low enough to deal with the situation of only surface-reaction between hydrogen and graphite. Empirical correlations of displacement thickness, local skin friction coefficient, local Nusselt number and local non-dimensional heat transfer rate have been obtained. The magnitude of the surface regression rate is found low enough to ensure the use of graphite as a linear or a component of the system over an extended period without loss of performance.

Nema, V. K.↗

Effects of Mach Number and Wall-Temperature Ratio on Turbulent Heat Transfer at Mach Numbers from 3 to 5

Heat-transfer data were evaluated from temperature time histories measured on a cooled cylindrical model with a cone-shaped nose and with turbulent flow at Mach numbers 3.00, 3.44, 4.08, 4.56, and 5.04. The experimental data were compared with calculated values using a modified Reynold's analogy between skin-friction and heat-transfer. Theoretical skin- friction coefficients were calculated using the method of Van Driest the method of Sommer and Short. The heat-transfer data obtained from the model were found to correlate when the 'T' method of Sommer and Short was used. The increase in turbulent heat-transfer rate with a reduction in wall to freestream temperature ratio was of the same order of magnitude as has been found for the turbulent skin-friction coefficient.

Tendeland, Thorval↗

A Moving Embedded Boundary Approach for the Compressible Navier-Stokes Equations in a Block-Structured Adaptive Refinement Framework

A computational technique has been developed to perform compressible flow simulations involving moving boundaries using an embedded boundary approach within the block-structured adaptive mesh refinement (SAMR) framework of AMReX [1], [91], [92]. We leverage the SAMR capability to obtain quantitatively accurate results whilst using robust, second-order finite volume schemes. A conservative, unsplit, cut-cell approach is utilized and a ghost-cell approach is developed for computing the flux on the moving, embedded boundary faces. A third-order least-squares formulation has been developed to compute the wall velocity gradients, and was found to significantly improve the performance of the solver in terms of the quantitative comparison of surface quantities such as the skin friction coefficient. Various test cases are performed to validate the method, and compared with analytical, experimental, and other numerical results in literature. Inviscid and viscous test cases are performed that span a wide regime of flow speeds - acoustic (harmonically pulsating sphere), smooth flows (expansion fan created by a receding piston) and flows with shocks (shock-cylinder interaction, shock-wedge interaction, pitching NACA 0012 airfoil and shock-cone interaction). A closed system with moving boundaries - an oscillating piston in a cylinder, showed that the percentage error in mass within the system decreases with refinement, demonstrating that the numerical scheme is conservative with grid refinement, but is not discretely conservative. Viscous test cases involve that of a horizontally moving cylinder at Re = 40, an inline oscillating cylinder at Re = 100, and a transversely oscillating cylinder at Re = 185. The judicious use of adaptive mesh refinement with appropriate refinement criteria to capture the regions of interest leads to well-resolved flow features, and good quantitative comparison is observed with the results available in literature.

adaptive refinement↗

A numerical study of flare stabilized projectiles at Mach 7.0

The effect of nose shape on two flare stabilized projectiles was studied using a Parabolized Navier-Stokes code. Pressure coefficients, forces and moments, skin friction coefficients, and Stanton number calculations are presented for the hemisphere-cylinder-flare and the cone-cylinder-flare configurations. Pitching moment and static margin plots versus flare angles and flare lengths are presented in a parametric study to show aerodynamic stability effects. Distinctly different flow field values of pressure, local Mach number, and dynamic pressure were generated by the two different nose configurations. These flow field values just upstream of the flare will be examined. The code demonstrated its value as a design tool by making a clear distinction between aerodynamically stable characteristics for this variety of nose shapes, flare angles, and flare lengths.

Hughson, Montgomery C.↗

Improvements to an Explicit Algebraic Stress Model for Turbulent Jet Mixing Predictions

Modifications to key coefficients in a k − E based explicit algebraic stress model (EASM) are examined with the objective of improving the prediction of turbulent jet flows. The pressure strain coefficient, C2 and the turbulent diffusion coefficients, σk and σE were investigated. For a series of benchmark subsonic jets at heated and unheated conditions, lowering C2 from the default value of 0.36 to 0.10 resulted in a significant improvement in the jet mixing, when compared to experimental data. Changing σk and σE from default values of 1.00 and 1.4489, respectively, to 0.50 and 0.7244, respectively, improved the initial mixing rate, while reducing the farfield mixing rate and the peak turbulent kinetic energy along the centerline. A high-speed mixing layer was also investigated for performance of baseline and modified EASM coefficients, with similar results as for the jet cases. A flat plate boundary layer was briefly examined to determine the effects of changing the coefficients on the turbulent skin friction coefficient. The change to the pressure strain coefficient, C2 = 0.10 is recommended for future EASM calculation of jets flow; however, it is also recommended that the diffusion coefficients remain at their default values.

Turbulent Mixing↗

Coupling of the FUN3D Unstructured Flow Solver and the LASTRAC Stability Code to Model Transition

We develop an iterative automated method to predict transition locations in boundary-layer flows by using the FUN3D solver to perform flow simulations and the LASTRAC code for linear stability computations. The coupling of FUN3D and LASTRAC allows for a robust physics-based approach to model boundary-layer transition by analyzing the growth of different instability waves and then using that information to iteratively update the resulting transition location. There is no user involvement during the iterative computations. We apply this automated method to subsonic flow over a flat plate with a sharp leading edge. The final solution has regions of laminar and turbulent flow with a transition onset location that agrees with experiments and stability-based correlations. This iterative automated method is also applied to an NLF(1)-0416 airfoil for conditions with and without a separation bubble. Along with predicting transition locations, we compare the streamwise distributions of surface-pressure and skin-friction coefficients to a transport-equation-based model. We consider a 6:1 prolate spheroid at three angles of attack, namely, five, ten, and fifteen degrees, where mixed-mode transition occurs due to both Tollmien-Schlichting and crossflow instabilities. The skin-friction contours and transition fronts at every angle of attack from our iterative automated method show good agreement with past experimental and computational results in the literature for the 6:1 prolate spheroid.

Transition↗