Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solid electrolyte interface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Multinuclear NMR Study of the Solid Electrolyte Interface Formed in Lithium Metal Batteries

The composition of the solid electrolyte interphase (SEI) layers associated with a high performance Cu|Li cell using lithium bis(fluorosulfonyi)imide (LiFSI) in 1,2-dimethoxyethane (DME) as electrolyte is determined by a multinuclear (6Li, 19F, 13C and 1H) solid-state MAS NMR study at high magnetic field (850 MHz). This cell can be cycled at high rates (4 mA•cm-2) for more than 1000 cycles with no increase in the cell impedance at high Columbic efficiency (average of 98.4%) in a highly concentrated LiFSI-DME electrolyte (4 M). LiFSI, LiF, Li2O2 (and/or CH3OLi), LiOH, Li2S and Li2O are observed in the SEI and validated by comparing with the spectra acquired on standard compounds and literature reports. To gain further insight into the role of the solute and its concentration dependence on the formation of SEIs while keeping the solvent of DME unchanged, the SEIs from different concentrations of LiFSI-DME and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-DME electrolyte are also investigated. It is found that LiF, a lithiated compound with superior mechanical strength and good Li+ ionic conductivity, is observed in the concentrated 4.0 M LiFSI-DME and the 3.0 M LiTFSI-DME systems but not in the diluted 1.0 M LiFSI-DME system. Li2O exists in both low and high concentration of LiFSI-DME while no Li2O is observed in the LiTFSI system. Furthermore, the dead metallic Li is reduced in the 4 M LiFSI-DME system compared with that in the 1 M LiFSI-DME system. Quantitative 6Li MAS results indicate that the SEI associated with the 4 M LiFSI-DEME is denser or thicker than that of the 1 M LiFSI-DME and the 3 M LiTFSI-DME systems. These findings are likely the reasons for explaining the high electrochemical performance associated with the high concentration LiFSI-DME system.

25 ENERGY STORAGE↗
DOE OSTI2023

Taming Metal–Solid Electrolyte Interface Instability via Metal Strain Hardening

Abstract Solid-state lithium metal batteries have emerged as a promising technology for electric vehicles due to their high specific energy and safety potential. Obtaining intimate contact between Li and electrolyte during cell fabrication, however, remains challenging. Adequate fabrication pressure is required to promote close contact, but this pressure can cause Li deformation and penetration into the electrolyte, resulting in poor battery performance. Here, a strategy for addressing this problem is presented by incorporating 3 at% Mg into Li. Unlike pure Li which obeys the Voce hardening law and allows unconstrained deformation, Li–Mg alloy follows the Swift hardening law and strengthens with strain under compression stress. Because of the constrained deformation of Li–Mg, intimate contact with solid electrolytes is possible even at high fabrication pressure (50–65 MPa), resulting in high critical current densities. These findings underscore the importance of understanding Li metal deformation properties to improve solid-state battery performance.

25 ENERGY STORAGE↗
DOE OSTI2026

Ionic Interdiffusion at Cathode|Solid-Electrolyte Interface: A Machine Learning–Assisted Multiscale Investigation and Mitigation Strategies

Future lithium batteries are expected to use solid electrolytes to achieve higher energy density and fast charge capabilities. However, most solid electrolytes are thermodynamically unstable against layered oxide cathodes. In this study, the stability of LiCoO2 (LCO) cathode with Li10GeP2S12 (LGPS) solid electrolyte is investigated using ab initio molecular dynamics (AIMD) and machine learning molecular dynamics (MLMD). The propensity of ionic interdiffusion, formation of a passivating interphase layer, and corresponding decay in cell performance is addressed using a continuum model. Large-scale MLMD simulations confirm that the LCO|LGPS interface permits interdiffusion of cobalt (Co) and other ionic species, leading to the formation and growth of a resistive interphase and to dramatic capacity fade even in the first cycle. We examine the literature evidence that incorporating a thin layer of LiNb0.5Ta0.5O3 (LNTO) between LCO and LGPS prevents the interdiffusion of ions. Atomistic simulations suggest that substituting lithium (Li) in LNTO with Co is thermodynamically unfavorable, thereby inhibiting ionic interdiffusion. The stable Nb5+/Ta5+ states form a rigid metal-oxide framework, which consequently also prevents the substitution of niobium (Nb) or tantalum (Ta). However, continuum-level analysis suggests that the higher mechanical stiffness of LNTO can lead to interfacial delamination between the LCO and LNTO. This phenomenon reduces the effectiveness of the protective layer. This paper, therefore, highlights the need to develop novel interlayers that balance low ionic interdiffusion with low mechanical stiffness.

Ncube, Musawenkosi K.↗
DOE OSTI2017

Formation of Reversible Solid Electrolyte Interface on Graphite Surface from Concentrated Electrolytes

Interfacial phenomena have always been key determinants for the performance of energy storage technologies. The solid electrolyte interfacial (SEI) layer, pervasive on the surfaces of battery electrodes for numerous chemical couples, directly affects the ion transport, charge transfer and lifespan of the entire energy system. Almost all SEI layers, however, are unstable resulting in the continuous consumption of the electrolyte. Typically, this leads to the accumulation of degradation products on/restructuring of the electrode surface and thus increased cell impedance, which largely limits the long-term operation of the electrochemical reactions. Herein, a completely new SEI formation mechanism has been discovered, in which the electrolyte components reversibly self-assemble into a protective surface coating on a graphite electrode upon changing the potential. In contrast to the established wisdom regarding the necessity of employing the solvent ethylene carbonate (EC) to form a protective SEI layer on graphite, a wide range of EC-free electrolytes are demonstrated for the reversible intercalation/deintercalation of Li+ cations within a graphite lattice, thereby providing tremendous flexibility in electrolyte tailoring for battery couples. This novel finding is broadly applicable and provides guidance for how to control interfacial reactions through the relationship between ion aggregation and solvent decomposition at polarized interfaces.

Environmental Molecular Sciences Laboratory↗
DOE OSTI2020

Electrolyte design for LiF-rich solid–electrolyte interfaces to enable high-performance microsized alloy anodes for batteries

Lithium batteries with Si, Al or Bi microsized (>10 µm) particle anodes promise a high capacity, ease of production, low cost and low environmental impact, yet they suffer from fast degradation and a low Coulombic efficiency. In this paper, we demonstrate that a rationally designed electrolyte (2.0 M LiPF 6 in 1:1 v/v mixture of tetrahydrofuran and 2-methyltetrahydrofuran) enables 100 cycles of full cells that contain microsized Si, Al and Bi anodes with commercial LiFePO 4 and LiNi 0.8 Co 0.15 Al 0.05 O 2 cathodes. Alloy anodes with areal capacities of more than 2.5 mAh cm -2 achieved >300 cycles with a high initial Coulombic efficiency of >90% and average Coulombic efficiency of >99.9%. These improvements are facilitated by the formation of a high-modulus LiF–organic bilayer interphase, in which LiF possesses a high interfacial energy with the alloy anode to accommodate plastic deformation of the lithiated alloy during cycling. Lastly, this work provides a simple yet practical solution to current battery technology without any binder modification or special fabrication methods.

25 ENERGY STORAGE↗
DOE OSTI2018

Solid electrolytes and interfaces in all-solid-state sodium batteries: Progress and perspective

All-solid-state sodium batteries are promising candidates for the next generation of energy storage with exceptional safety, reliability and stability. The solid electrolytes are key components for enabling all-solid-state sodium batteries with high electrochemical performances. This Review discusses the current developments on inorganic and organic sodium ions solid electrolytes, including β/β’’-alumina, NASICON, sulfides, polymers and others. In particular, the structures, ionic conductivities and fabrications as well as electrochemical/chemical stabilities of solid electrolytes are discussed. Furthermore, the effective approaches for forming intimate interfaces between solid electrolytes and electrodes are also reviewed. And perspectives on future developments in the field of solid electrolytes and possible directions to improve interfacial contacts for future practical applications of all-solid-state sodium batteries are included.

25 ENERGY STORAGE↗
DOE OSTI2024

Electro-Chemo-Mechanical Evolution at the Garnet Solid Electrolyte–Cathode Interface

Solid-state batteries promise higher energy density and improved safety compared with lithium-ion batteries. However, electro-chemomechanical instabilities at the solid electrolyte interface with the cathode and the anode hinder their large scale implementation. Here, in this study, we focus on resolving electro-chemo-mechanical instability mechanisms and their onset conditions between a state-of-the-art cathode, LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), and the garnet Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte. We used thin-film NMC622 on LLZO pellets to place the interfacial region within the detection depth of the X-ray characterization techniques. The experimental probes of the near-interface region included in operando X-ray absorption spectroscopy and ex situ focused ion beam scanning electron microscopy. Electrochemical degradation was not observable during cycling at room temperature with 4.3 V versus Li/Li + charge voltage cutoff, or with stepwise potentiostatic hold up to 4.1 V versus Li/Li + . In contrast, secondary phases including reduced transition metal species (Ni 2+ , Co 2+ ) were found after cycling up to 4.3 V versus Li/Li + at 80 °C and during potentiostatic hold at 4.3 V versus Li/Li + (Ni 2+ ). Intergranular cracks between NMC622 grains and delamination at the NMC622|LLZO interface occurred readily after the first charge. These interface reaction products and mechanical failure lowered the capacity and cell efficiency due to partial loss of the NMC622 phase, partial loss of contact at the interface, and a higher polarization resistance. Electrochemical instability between delithiated NMC622 and LLZO could be mitigated by using a low charge voltage cutoff or cycling at lower temperature. Ways to engineer the mechanical properties to avoid crack deflection and delamination at the interface are also discussed for enhancing mechanical stability.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Self-Assembling and Self-Healing Rechargeable Li Batteries

Investigate formation of lithium halide containing solid electrolyte interface. Characterize the structure and composition of the solid electrolyte interface surface film and morphology of the electrochemically deposited lithium. Develop combinations of electrolytes (solvents + salts) and electrolyte additives that produce a highly Li-ion conducting, mechanically robust, and self-healing solid electrolyte interface to suppress Li dendrite formation and improve Coulombic efficiency.

25 ENERGY STORAGE↗
DOE OSTI2022

Self-assembling and self-healing rechargeable Li batteries Final Scientific/Technical Report

PROJECT OBJECTIVE: Investigate formation of lithium halide containing solid electrolyte interface. Characterize the structure and composition of the solid electrolyte interface surface film and morphology of the electrochemically deposited Li. Develop combinations of electrolytes (solvents + salts) and electrolyte additives that produce a highly Li-ion conducting, mechanically robust, and self-healing solid electrolyte interface to suppress Li dendrite formation and improve Coulombic efficiency.

Chiang, Yet-Ming↗
DOE OSTI2021

Ion correlations drive charge overscreening and heterogeneous nucleation at solid–aqueous electrolyte interfaces

Significance Ion distributions at charged solid–water interfaces, referred to as the electrical double layer (EDL), are poorly understood at high ion concentrations, in part due to the lack of molecular-scale descriptions of the interactions between adsorbed hydrated ions. Here, direct visualization of the salinity-dependent evolution of EDL structure reveals molecular origins of nonclassical transformation of the EDL, in which charge overscreening and heterogeneous nucleation are driven by ion–ion correlations at the interfaces. This manifestation of the atomistic basis of nonclassical behaviors provides a much-needed understanding of the impact of ion cooperativity at charged interfaces for the development of predictive models for element transport in natural environments and advanced technologies for material growth and synthesis in saline environments.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Low temperature sulfur and sodium metal battery for grid-scale energy storage application

A re-chargeable battery comprising a non-dendrite forming sodium (Na)/potassium (K) liquid metal alloy anode, a sulfur and polyacrylonitrile (PAN) conductive polymer composite cathode, a polyethyleneoxide (PEO) solid electrolyte, a solid electrolyte interface (SEI) formed on the PEO solid electrolyte; and a cell housing, wherein the anode, cathode, and electrolyte are assembled into the cell housing with the PEO solid electrolyte disposed between the cathode and anode.

Liu, Gao↗
DOE OSTI2024

ARJUNA: An Electrochemical Interface Mapping Probe for Solid-State Batteries

Solid-state batteries (SSBs) are promising candidates for next-generation energy storage, although their performance can be compromised by interfacial heterogeneity within the electrolyte. Furthermore, ensuring the quality of large form-factors electrolyte film is crucial for establishing a robust manufacturing platform for solid-state batteries. Herein, we report on the use of ARJUNA, an electrochemical interface mapping system, to characterize heterogeneities at solid electrolyte interfaces and to serve as a quality control system for SSB manufacturing. In addition to spatial mapping, the proposed system can also probe the interface behavior as a function of pressure and temperature. We present the operating principle, design, instrumentation, and evaluation of the system alongside a typical hybrid solid electrolyte produced using two common manufacturing processes. This report showcases the capability of ARJUNA to probe the heterogeneity and quality of processed solid electrolyte films.

25 ENERGY STORAGE↗
DOE OSTI2025

Direct Prelithiation of Silicon-Based Composite Electrodes via Island-like Thermal Evaporation

Irreversible losses of Li during solid electrolyte interface (SEI) conditioning is a key contributor to the lower specific capacities observed in silicon-containing Li-ion batteries. Herein, thermal evaporation of between 1 and 20 µm of Li onto Si-based composite anodes has been investigated as a prelithiation method to account for such losses. To account for mechanical strain caused by Li-Si alloying during the deposition, a stainless-steel mesh is applied to the electrodes before prelithiation to form “island-like” deposition on the electrode surface. The open circuit potential was also found to decrease as a function of increased Li evaporation, consistent with the potentials of electrochemically prepared LixSi alloys. Prelithiating to account for irreversible Li losses to SEI formation resulted in full cells with a 15.8% increase in initial coulombic efficiency and a 47.8% reduction in irreversible capacity loss after SEI formation cycling. Subsequent C/3 cycling showed up to a 62.9% increase in specific capacity in prelithiated cells. X-ray photoelectron spectroscopy (XPS) revealed differences in the SEI composition that was formed by electrochemical cycling and reactively formed in prelithiated cells upon exposure to Gen2 + 3% FEC electrolyte. The reactively formed SEI from the spontaneous reaction with lithiated silicon was carbonate-rich while the electrochemical SEI formation showed significantly more LiPFx species, which could play a role in overall cycling performance.

Musgrove, Amanda↗
DOE OSTI2021

Recent progress and future prospects of atomic layer deposition to prepare/modify solid-state electrolytes and interfaces between electrodes for next-generation lithium batteries

Lithium ion batteries (LIBs) are encouraging electrochemical devices with remarkable properties including a high energy/power density, fast charging capability, and low self-discharge rate. Further increase in energy density as well as safe usage is needed for next-generation LIBs in electric transportation vehicles. Solid-state electrolytes (SSEs) are very promising for high-performance LIBs since they enable improved safety along with increased energy density compared to flammable liquid organic electrolytes. However, utilizing SSEs with a Li metal anode is very challenging due to the possibility of undesired side reactions and the formation of an unstable solid-electrolyte interphase. Therefore, it is critical to enhance the stability of SSEs against the Li anode. One feasible approach is to form a thin and conductive interlayer between the Li anode and solid-state electrolyte. Atomic layer deposition (ALD) is a unique technique for conformal coating of complex 3D structures with finely controlled film thickness (at the atomic scale). ALD coating on the surface of SSEs can be adopted for engineering solid-electrolyte interfaces with desired attributes and improved stability. In this review paper, we have discussed recent progress in implementing the ALD technique for depositing thin layers on various SSE configurations including lithium phosphorus oxynitride (LiPON), garnets, oxides, perovskites, sulphides, Li 3 BO 3 –Li 2 CO 3 (LBCO), and sodium super ionic conductors (NASICON). We have also highlighted the major areas for future research and development in the field. We believe that this review will be very helpful for directing future research on implementing ALD for synthesizing stable and high-performance SSEs with an engineered solid-electrolyte interface for next-generation electrochemical devices (e.g., Li-ion batteries, supercapacitors, and flow batteries).

36 MATERIALS SCIENCE↗