SEARCH · Search NASA

Results for “Solvent casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

DOE OSTI2024

A High-Ceramic-Loading LATP–PVDF–Al 2 O 3 Composite Film for Lithium-Ion Batteries With Favorable Porous Microstructure and Enhanced Thermal Stability

A separator plays a crucial role in a Li-ion battery to carry liquid electrolytes while preventing short-circuiting between electrodes. Nevertheless, conventional commercial separators often exhibit poor wettability and are prone to shrink at elevated temperatures due to their limited thermal stability. Herein, we report a heat-resistant LATP–PVDF–Al 2 O 3 composite film with outstanding wetting performance. The thin film was prepared using ball mill mixing and tape-casting processes. Two solvents, NMP and glycerol, were applied to prepare the slurry, and a favorable microstructure in the film was created after drying. Here, the ionic conductivity of the film was tested at 1.39 mS cm –1 when paired with liquid electrolyte, almost double that of the commercial counterpart. The high ceramic loading of 70% improved both the thermal shrinkage resistance and dendrite inhibition of the membrane. When assembled in an NMC half-cell, the cycling capacity retentions of 92.8% and 92.1% are achieved after 50 cycles at 0.5 C and 1 C, demonstrating its capability to be used in Li-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2025

Long carbon fibers boost performance of dry processed Li-ion battery electrodes

Dry processing (DP) is an advanced manufacturing technique for lithium-ion battery (LIB) electrodes. Unlike conventional wet-process-based manufacturing that involves dissolving polyvinylidene fluoride (PVDF) binder in n-methyl-2-pyrrolidone (NMP) solvent for slurry-casting, DP involves fibrillation of polymer binders. This method offers environmental and cost benefits by eliminating the need for expensive and environmentally hazardous organic solvents. However, DP-produced electrode films often lack mechanical stability due to the absence of a current collector substrate during electrode material layer fabrication. This reduced mechanical instability results in difficulty during fabricating of thin electrodes (≈5 mAh/cm 2 ). To address this issue, long (>8 mm) carbon fiber (CF) has been incorporated to reinforce the mechanical strength of the electrode films. In conclusion, the study demonstrates that the inclusion of long carbon fiber boosts the mechanical, electrical, thermal, and electrochemical performance of DP electrodes.

25 ENERGY STORAGE↗

DOE OSTI2020

Impact of Dispersion Solvent on Ionomer Thin Films and Membranes

Perfluorosulfonic acid (PFSA) ionomers are an important class of materials that many electrochemical devices rely on as their ion-conducting electrolyte. Often, PFSA films are prepared through solution-processing techniques. Previous research has demonstrated that the solvent environment affects PFSA dispersion conformation, but it is not clear to what extent (if at all) these conformational effects persist for thin films and membranes upon casting, nor how dispersion solvent impacts film formation during the drying process. Here in this paper, we explore these questions by systematically examining the effect of Thin Film all length scales affected by dispersion solvent water and n-propanol mixtures on PFSA thin-film formation and structure, membrane structure, and resulting properties. Using a combination of in situ, time-resolved grazing incidence X-ray scattering and tender wide-angle X-ray scattering, it is shown that films prepared from high-water-concentration dispersions exhibit stronger interactions and arrangement upon drying, and possess larger network domain sizes than those prepared from low-water-concentration dispersions. These stronger interactions likely manifest in greater network connectivity, as evidenced by enhanced conductivity for membranes and decreased water uptake for thin films. Significantly, these solvent-induced differences persist even after thermal annealing. It is clear that the dispersion solvent choice is a critical parameter controlling PFSA nano- and mesoscale structure and presents an important dial with which to direct PFSA macroscale properties.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Cast Film Production with Polyethylene Recycled from a Post-Industrial Printed Multilayer Film by Solvent-Targeted Recovery and Precipitation

The solvent-targeted recovery and precipitation (STRAP) process separates and recovers the constituent resins in multilayer plastic packaging films by selective polymer dissolution. In this work, three different experimental methods were considered to recover a polyethylene (PE) resin from a printed multilayer film by STRAP. The methods consisted of (1) a filter bag system, (2) a Soxhlet extraction, and (3) a jacketed dissolution vessel. Cast films were produced with the PE recovered from each method and were analyzed for color, mechanical properties, and number of impurities. High-quality recycled PE cast films can be produced by increasing the solvent to plastic ratio, including a filter pore size of 100 μm, and optimizing temperature control in STRAP. Furthermore, this study demonstrates that STRAP polymers can be recycled back into plastic films, enabling the potential circularity of these packaging materials.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Preparation of defect-free asymmetric gas separation membranes with dihydrolevoglucosenone (Cyrene TM ) as a greener polar aprotic solvent

Nonsolvent-induced phase separation (NIPS) is widely used to prepare asymmetric gas separation membranes. Most industrial NIPS casting solution formulations are limited to a small group of glassy polymers and, importantly, require toxic polar aprotic solvents such as N,N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), or N-methyl-2-pyrrolidone (NMP). Growing restrictions on the use of such solvents are spurring the search for more benign casting solution formulations that do not compromise membrane performance. Herein this study reports high-flux, defect-free asymmetric polysulfone (PSf) gas separation membranes prepared using dihydrolevoglucosenone (Cyrene TM ), a polar aprotic solvent that is believed to be safer than DMAc, DMF, and NMP, as the majority casting solution component. Optimized formulations and casting conditions produce membranes with hydrogen permeances exceeding 100 gas permeance units (GPU) and selectivities at or above those of dense PSf films. Dry/wet NIPS membrane performance improved with shorter dry step times and increased Cyrene TM loadings relative to the volatile solvent, tetrahydrofuran (THF), in the casting solution. The high water-Cyrene TM Flory-Huggins interaction parameter, $\mathcal{X}12$ , and high casting solution viscosities help suppress the formation of skin layer defects and sublayer macrovoids. In some cases, membrane selectivities were influenced by substructure resistance, providing insight into the relationship between sublayer morphology and membrane performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Solvent-Free Manufacturing of Lithium-Ion Battery Electrodes via Cold Plasma

Slurry casting has been used to fabricate lithium-ion battery electrodes for decades, which involves toxic and expensive organic solvents followed by high-cost vacuum drying and electrode calendering. This work presents a new manufacturing method using a nonthermal plasma to create inter-particle binding without using any polymeric binding materials, enabling solvent-free manufacturing electrodes with any electrochemistry of choice. The cold-plasma-coating technique enables fabricating electrodes with thickness (>200 μm), high mass loading (>30 mg cm -2 ), high peel strength, and the ability to print lithium-ion batteries in an arbitrary geometry. This crosscutting, chemistry agnostic, platform technology would increase energy density, eliminate the use of solvents, vacuum drying, and calendering processes during production, and reduce manufacturing cost for current and future cell designs. Here, lithium iron phosphate and lithium cobalt oxide were used as examples to demonstrate the efficacy of the cold-plasma-coating technique. It is found that the mechanical peel strength of cold-plasma-coating-manufactured lithium iron phosphate is over an order of magnitude higher than that of slurry-casted lithium iron phosphate electrodes. Full cells assembled with a graphite anode and the cold-plasma-coating-lithium iron phosphate cathode offer highly reversible cycling performance with a capacity retention of 81.6% over 500 cycles. For the highly conductive cathode material lithium cobalt oxide, an areal capacity of 4.2 mAh cm -2 at 0.2 C is attained. We anticipate that this new, highly scalable manufacturing technique will redefine global lithium-ion battery manufacturing providing significantly reduced plant footprints and material costs.

25 ENERGY STORAGE↗

DOE OSTI2021

Phase segregation mechanisms of small molecule-polymer blends unraveled by varying polymer chain architecture

As phase separation between the small-molecule semiconductor and the polymer binder is the key enabler of blend-based organic field-effect transistors (OFETs) fabricated by low-cost solution processing, it is crucial to understand the underlying phase separation mechanisms that determine the phase morphology, which significantly impacts device performance. Beyond the parameter space investigated in previous work, here we investigate the formation of blends by varying the branch architecture of the polymer binder and by shortening the solvent dry time using ultrasonic spray casting. The phase morphologies of the resulting blend films have been thoroughly characterized with a variety of techniques in three dimensions over multiple length scales, including AFM, energy-filtered transmission electron microscope, and neutron reflectivity, and have been correlated with electrical transport performance. From the results, we have inferred that the phase morphology is kinetically determined, limited by the inherent slow movement of polymer macromolecules. The kinetic picture, supported by molecular dynamics modeling, not only consistently explains our observations but also resolves inconsistencies in previous works. The achieved mechanistic understanding will guide further optimization of blend-based organic electronics, such as OFETs and organic photovoltaics.

36 MATERIALS SCIENCE↗

DOE OSTI2025

New directions and principles for solvent extraction for recovery of lithium from aqueous brines and mineral leachates: A brief review

Increasing demand for lithium for manufacturing of batteries is fueling the unprecedented search for improved recovery and alternative sources. Wider source distribution, lower energy consumption, and greater sustainability make extraction of lithium from brines, both natural and process-derived, an attractive alternative to mineral ores. Solvent extraction, used industrially for production of metals, salts, and pharmaceuticals, has been investigated as a methodology for lithium recovery for several decades. However, industrial application of solvent extraction for lithium recovery has so far been limited. In contrast, direct lithium extraction using adsorbents based on inorganic minerals has rapidly advanced from research to commercialization. A comparison of solvent extraction processes to adsorption highlights these issues and explains the preference for adsorbents. Although the application of solvent extraction has been criticized for use of large amounts of acid, alkali, and organic solvents, steady progress has been made to improve its potential for industrial lithium production, spurred on generally by the advantages of solvent extraction in selectivity and throughput. Previously developed beta-diketone, organophosphate, and crown ether ligands are being adapted and improved. Their novel use with ionic liquids, deep eutectic solvents, and membrane technologies promises to expand capabilities for extraction of lithium from dilute aqueous sources while improving sustainability. Possibilities for further discovery and innovation abound. In this review, we provide a unique perspective from the field of solvent extraction starting with fundamentals such as ion-transfer theory and apply them to understanding lithium selectivity and extraction behavior. In conclusion, the results are cast in the light of the practical realities of developing economical solvent extraction processes.

Brine↗

DOE OSTI2023

Impact of fabrication methods on binder distribution and charge transport in composite cathodes of all-solid-state batteries

Abstract The manufacturing process of all-solid-state batteries necessitates the use of polymer binders. However, these binders, being ionic insulators by nature, can adversely affect charge transport within composite cathodes, thereby impacting the rate performance of the batteries. In this work, we aim to investigate the impact of fabrication methods, specifically the solvent-free dry process versus the slurry-cast wet process, on binder distribution and charge transport in composite cathodes of solid-state batteries. In the dry process, the binder forms a fibrous network, while the wet process results in binder coverage on the surface of cathode active materials. The difference in microstructure leads to a notable 20-fold increase in ionic conductivity in the dry-processed cathode. Consequently, the cells processed via the dry method exhibit higher capacity retention of 89% and 83% at C/3 and C/2 rates, respectively, in comparison to 68% and 58% for the wet-processed cells at the same rate. These findings provide valuable insights into the influence of fabrication methods on binder distribution and charge transport, contributing to a better understanding of the binder’s role in manufacturing of all-solid-state batteries.

Emley, Benjamin↗

DOE OSTI2021

Method for producing PBI films without organic solvents

A novel process for making PBI films starting from gel PBI membranes polymerized and casted in the PPA process wherein acid-imbibed gel PBIs are neutralized in a series of water baths and undergo controlled drying in association with a substrate material, yielding a PBI film without the use of organic solvents.

Murdock, Laura A.↗

DOE OSTI2024

PBI films formed without use of organic solvents

Murdock, Laura A.↗

DOE OSTI2020

Optimization of Lithium Content and Sintering Additives in Tape Cast Lithium Garnet Electrolyte Sheets

The lithium garnet (LLZO) remains one of the most promising electrolyte materials for producing solid state batteries. Tape casting is one method for producing the thin ceramic electrolyte layer required for a high-performance solid state battery. Processing of LLZO is complicated by several factors including lithium volatilization, abnormal grain growth and phase instability. Many of these issues are exacerbated in tape cast sheets by the sheets' higher surface area to volume ratio, when compared to pellet processing methods. Here, we report on an environmentally friendly aqueous tape casting process for LLZO using methylcellulose as a binder and compare final sheet properties to other, solvent-based, options. Solids loading, binder content, dispersant composition, and wetting agent type are varied to improve ease of casting and enhance properties of the as-cast tape. Lithium content in sintered LLZO sheets is controlled by the inclusion of excess Li 2 CO 3 as lithium source in the ceramic tape itself and by a novel method of producing a lithium-saturated furnace atmosphere. Sintering time and temperature are optimized, and rapid thermal processing is investigated as a method of reducing lithium loss. Al 2 O 3 and MgO are examined for use as sintering additives. Characterization of LLZO sheets is performed with XRD, EIS and SEM. Li 2 CO 3 and sintering additive levels are optimized for ionic conductivity and density. The optimization effort improved the conductivity and density of 100µm thick sintered sheets to greater than 3x10 -4 S/cm conductivity and 90% density.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Polyacrylonitrile-based electrolytes: How processing and residual solvent affect ion transport and stability

Polyacrylonitrile (PAN) is one of the alternative candidate polymer hosts to form solid polymer electrolytes (SPEs) besides the widely used poly(ethylene oxide). In this study, we systematically investigate the processing of PAN based SPEs containing lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) salt, using dimethylformamide (DMF) as the solvent. The effects of PAN processing procedure including solution mixing, casting, and drying on the morphology, ion transport, solvation structure, Li and oxidative stability of PAN electrolytes are thoroughly examined. In particular, four drying conditions are investigated and the amount of residual DMF is accurately determined using infrared (IR) spectroscopy. Varying the drying conditions can lead to five orders of magnitude decrease in the ionic conductivity. As DMF content decreases, the SPE's stability again Li metal dramatically improves. The practical oxidative stability is also strongly affected by the residual DMF content, ranging from 2.5 V to 3.5 V, much lower than reported values. Finally, the role of the residual DMF solvent is elucidated. DMF content vitally influences ion solvation structure at different concentration regimes, which ultimately dictates the ion conduction mechanism and oxidative stability of PAN based SPEs. In conclusion, this thorough study lays the groundwork for future development of PAN based electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Auxiliary sequential deposition enables 19%-efficiency organic solar cells processed from halogen-free solvents

High-efficiency organic solar cells are often achieved using toxic halogenated solvents and additives that are constrained in organic solar cells industry. Therefore, it is important to develop materials or processing methods that enabled highly efficient organic solar cells processed by halogen free solvents. In this paper, we report an innovative processing method named auxiliary sequential deposition that enables 19%-efficiency organic solar cells processed by halogen free solvents. Our auxiliary sequential deposition method is different from the conventional blend casting or sequential deposition methods in that it involves an additional casting of dithieno[3,2-b:2’,3’-d]thiophene between the sequential depositions of the donor (D18-Cl) and acceptor (L8-BO) layers. The auxiliary sequential deposition method enables dramatic performance enhancement from 15% to over 18% compared to the blend casting and sequential deposition methods. Furthermore, by incorporating a branched-chain-engineered acceptor called L8-BO-X, device performance can be boosted to over 19% due to increased intermolecular packing, representing top-tier values for green-solvent processed organic solar cells. Comprehensive morphological and time-resolved characterizations reveal that the superior blend morphology achieved through the auxiliary sequential deposition method promotes charge generation while simultaneously suppressing charge recombination. This research underscores the potential of the auxiliary sequential deposition method for fabricating highly efficient organic solar cells using environmentally friendly solvents.

14 SOLAR ENERGY↗

DOE OSTI2020

Evaporation-Induced Vertical Alignment Enabling Directional Ion Transport in a 2D-Nanosheet-Based Battery Electrode

2D nanosheets have been widely explored as electrode materials owing to their extraordinarily high electrochemical activity and fast solid-state diffusion. However, the scalable electrode fabrication based on this type of material usually suffers from severe performance losses due to restricted ion-transport kinetics in a large thickness. Here, a novel strategy based on evaporation-induced assembly to enable directional ion transport via forming vertically aligned nanosheets is reported. The orientational ordering is achieved by a rapid evaporation of mixed solvents during the electrode fabrication process. Compared with conventional drop-cast electrodes, which exhibit a random arrangement of the nanosheets and obvious decrease of rate performance with increasing thickness, the electrode based on the vertically aligned nanosheets is able to retain the original high rate capability even at high mass loadings and electrode thickness. Furthermore, combined electrochemical and structural characterization reveals the electrode composed of orientation-controlled nanosheets to possess lower charge-transfer resistances, leading to more complete phase transformation in the active material.

25 ENERGY STORAGE↗

DOE OSTI2025

Green solvent-processable poly(3-hexylthiophene) derivative maintains high hole mobility in diodes

The development of environmentally sustainable fabrication methods for organic solar cells (OSCs) is critical to enable their large-scale adoption. Conventional solution-processed OSCs often rely on halogenated, toxic solvents that pose health and environmental risks, limiting their scalability. This is because π-conjugated polymers tend to have a low solubility in non-halogenated solvents. A common strategy to enhance solubility in alternative solvents is through the incorporation of polar solubilizing groups, often on every repeat unit of at least one monomer. However, too many polar side chains tend to disrupt favorable morphology and decrease charge transport properties. In this study, we demonstrate that a minimal degree of side chain functionalization can improve green solvent processability while preserving electrical performance. We tested this hypothesis using our previously reported random copolymer derivative of poly(3-hexylthiophene) (P3HT) where ∼10 mol% of the side chains are 6-pentanoatehexyl side chains. We find that this low-level functionalization significantly broadens the solvents that can be used to process P3HT to less toxic solvents such as o-xylene and anisole. Furthermore, the copolymer processed from greener solvents showed high hole mobilities (∼10⁻ 3 cm 2 /Vs by the Space-Charge Limiting Current method in diodes), comparable to P3HT films cast from toxic chloroform. These findings suggest that minimal side-chain modification is a viable strategy for expanding green solvent compatibility while preserving electrical performance, paving the way toward more sustainable organic semiconductor designs.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Highly permeable polyethersulfone substrates with bicontinuous structure for composite membranes in CO 2 /N 2 separation

Substrate morphology has a significant effect on the CO 2 transport performance of a thin-film composite (TFC) membrane. In this study, a new mixed solvent comprising 2-pyrrolidone (2-PD) and 2-methoxyethanol (2-ME) was used to prepare polyethersulfone (PES) substrates with bicontinuous structure by water vapor-induced phase separation, followed by immersion in water as nonsolvent. Here, compared with the commonly used solvent, N-methyl-2-pyrrolidone (NMP), the 2-PD/2-ME mixed solvent is more hydrophilic and can decrease the thermodynamic stability of the casting solution significantly. As a result, the phase separation was induced via the spinodal decomposition mechanism. The open morphology bestowed the optimized substrate with a very high CO 2 permeance of 133,226 ± 3,870 GPU (1 GPU = 10 –6 cm 3 (STP) s –1 cm –2 cmHg –1 = 3.3464 × 10 -9 kg-mol s –1 m –2 Pa –1 ), which was 5 times more permeable than the baseline substrate synthesized with NMP. By using this new substrate, the prepared TFC membrane containing amines showed an increased CO 2 permeance of 908 ± 8 GPU at 57°C, which was 48 GPU higher than that with the baseline substrate. Meanwhile, the CO 2 /N 2 selectivity was retained at 162 ± 4 at 57°C. In addition, the good scalability of the new PES substrate was demonstrated by roll-to-roll fabrication of a 50' long scale-up PES substrate with a width of 21".

2-Pyrrolidone↗

DOE OSTI2021

Effect of Polyphenylsulfone and Polysulfone Incompatibility on the Structure and Performance of Blend Membranes for Ultrafiltration

This study deals with the modification of polyphenylsulfone ultrafiltration membranes by introduction of an incompatible polymer polysulfone to the polyphenylsulfone casting solution to improve the permeability. The correlation between properties of the blend polyphenylsulfone/polysulfone solutions and porous anisotropic membranes for ultrafiltration prepared from these solutions was revealed. The blend polyphenylsulfone/polysulfone solutions were investigated using a turbidity spectrum method, optical microscopy and measurements of dynamic viscosity and turbidity. The structure of the prepared blend flat sheet membranes was studied using scanning electron microscopy. Membrane separation performance was investigated in the process of ultrafiltration of human serum albumin buffered solutions. It was found that with the introduction of polysulfone to the polyphenylsulfone casting solution in N-methyl-2-pyrrolidone the size of supramolecular particles significantly increases with the maximum at (40–60):(60:40) polyphenylsulfone:polysulfone blend ratio from 76 nm to 196–354 nm. It was shown that polyphenylsulfone/polysulfone blend solutions, unlike the solutions of pristine polymers, are two-phase systems (emulsions) with the maximum droplet size and highest degree of polydispersity at polyphenylsulfone/polysulfone blend ratios (30–60):(70–40). Pure water flux of the blend membranes passes through a maximum in the region of the most heterogeneous structure of the casting solution, which is associated with the imposition of a polymer-polymer phase separation on the non-solvent induced phase separation upon membrane preparation. The application of polyphenylsulfone/polysulfone blends as membrane-forming polymers and polyethylene glycol (Mn = 400 g·mol -1 ) as a pore-forming agent to the casting solutions yields the formation of ultrafiltration membranes with high membrane pure water flux (270 L·m -2 ·h -1 at 0.1MPa) and human serum albumin rejection of 85%.

36 MATERIALS SCIENCE↗