Search NASA⌕ Search

SEARCH · Search NASA

Results for “Spray Forming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Status update on the US ODS development program

Three papers are attached highlighting some recent progress in the development and testing of Oxide Dispersion Strengthened ferritic steels in tube and plate form. Aydogan et al. (2016) and Alam et al. (2016) papers summarize testing and characterization that has been performed on plate and tube materials. In the Alam et al. paper it was noted that after cross-rolling plate material of 14YWT, microcracks were formed. This resulted from an (001) texture in the plane normal to the plate causing cracking microcracking within that plane. Such microcracking affects low temperature tensile properties up to 200C. It was not seen in tube material produced by hydrostatic extrusion. In the Aydogan et al. (2016) paper characterization was performed on tubes produced from the ODS material, 14YWT. Tubes were formed through hydrostatic extrusion of plate material and hydrostatic extrusion of spray formed tubes. It was noted that strong texture on {001}<110> was formed in the plate material while shear deformation during hot extrusion produced a strong <111> ll ND texture component. In the Aydogan et al. (2017) paper detailed analysis was performed on the change in oxide size with ion irradiation to doses >500 dpa at 450C. The results show strong stability for the 2-4 nm oxide particles with a reduction in size ~25% after 270 dpa and an increase in density.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigation of Pressurized Entrained-Flow Kraft Black Liquor Gasification in an Industrially Relevant Environment

The University of Utah's project 'Investigation of Pressurized Entrained-Flow Kraft Black Liquor Gasification in an Industrially Relevant Environment' (U.S. DOE Cooperative Agreement DE-FC26-04NT42261) was a response to U.S. DOE/NETL solicitation DE-PS36-04GO94002, 'Biomass Research and Development Initiative' Topical Area 4-Kraft Black Liquor Gasification. The project began September 30, 2004. The objective of the project was to improve the understanding of black liquor conversion in high pressure, high temperature reactors that gasify liquor through partial oxidation with either air or oxygen. The physical and chemical characteristics of both the gas and condensed phase were to be studied over the entire range of liquor conversion, and the rates and mechanisms of processes responsible for converting the liquor to its final smelt and syngas products were to be investigated. This would be accomplished by combining fundamental, lab-scale experiments with measurements taken using a new semi-pilot scale pressurized entrained-flow gasifier. As a result of insufficient availability of funds and changes in priority within the Office of Biomass Programs of the U.S. Department of Energy, the research program was terminated in its second year. In total, only half of the budgeted funding was made available for the program, and most of this was used during the first year for construction of the experimental systems to be used in the program. This had a severe impact on the program. As a consequence, most of the planned research was unable to be performed. Only studies that relied on computational modeling or existing experimental facilities started early enough to deliver useful results by the time to program was terminated Over the course of the program, small scale (approx. 1 ton/day) entrained-flow gasifier was designed and installed at the University of Utah's off-campus Industrial Combustion and Gasification Research Facility. The system is designed to operate at pressures as high as 32 atmospheres, and at temperatures as high as 1500 C (2730 F). Total black liquor processing capacity under pressurized, oxygen-blown conditions should be in excess of 1 ton black liquor solids per day. Many sampling ports along the conversion section of the system will allow detailed analysis of the environment in the gasifier under industrially representative conditions. Construction was mostly completed before the program was terminated, but resources were insufficient to operate the system. A system for characterizing black liquor sprays in hot environments was designed and constructed. Silhouettes of black liquor sprays formed by injection of black liquor through a twin fluid (liquor and atomizing air) nozzle were videoed with a high-speed camera, and the resulting images were analyzed to identify overall characteristics of the spray and droplet formation mechanisms. The efficiency of liquor atomization was better when the liquor was injected through the center channel of the nozzle, with atomizing air being introduced in the annulus around the center channel, than when the liquor and air feed channels were reversed. Atomizing efficiency and spray angle increased with atomizing air pressure up to a point, beyond which additional atomizing air pressure had little effect. Analysis of the spray patterns indicates that two classifications of droplets are present, a finely dispersed 'mist' of very small droplets and much larger ligaments of liquor that form at the injector tip and form one or more relatively large droplets. This ligament and subsequent large droplet formation suggests that it will be challenging to obtain a narrow distribution of droplet sizes when using an injector of this design. A model for simulating liquor spray and droplet formation was developed by Simulent, Inc. of Toronto. The model was able to predict performance when spraying water that closely matched the vendor specifications. Simulation of liquor spray indicates that droplets on the order 200-300 microns can be expected, and that higher liquor flow will result in better distribution of liquor in the reactor.

09 BIOMASS FUELS↗

Characterization of Tubing from Advanced ODS alloy (FCRD-NFA1)

Fabrication methods are being developed and tested for producing fuel clad tubing of the advanced ODS 14YWT and FCRD-NFA1 ferritic alloys. Three fabrication methods were based on plastically deforming a machined thick-wall tube sample of the ODS alloys by pilgering, hydrostatic extrusion or drawing to decrease the outer diameter and wall thickness and increase the length of the final tube. The fourth fabrication method consisted of the additive manufacturing approach involving solid-state spray deposition (SSSD) of ball milled and annealed powder of 14YWT for producing thin-wall tubes. Of the four fabrication methods, two methods were successful at producing tubing for further characterization: production of tubing by high-velocity oxy-fuel spray forming and production of tubing using high-temperature hydrostatic extrusion. The characterization described shows through neutron diffraction the texture produced during extrusion while maintaining the beneficial oxide dispersion. In this research, the parameters for innovative thermal spray deposition and hot extrusion processing methods have been developed to produce the final nanostructured ferritic alloy (NFA) tubes having approximately 0.5 mm wall thickness. Effect of different processing routes on texture and grain boundary characteristics has been investigated. It was found that hydrostatic extrusion results in combination of plane strain and shear deformations which generate rolling textures of α- and γ-fibers on {001}<110> and {111}<110> together with a shear texture of ζ-fiber on {011}<211> and {011}<011>. On the other hand, multi-step plane strain deformation in cross directions leads to a strong rolling textures of θ- and ε-fiber on {001}<110> together with weak γ-fiber on {111}<112>. Even though the amount of the equivalent strain is similar, shear deformation leads to much lower texture indexes compared to the plane strain deformations. Moreover, while 50% of hot rolling brings about a large number of high-angle grain boundaries (HAB), 44% of shear deformation results in large amount of low-angle boundaries (LAB) showing the incomplete recrystallization.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Grain size softening effect in Al{sub 62.5}Cu{sub 25}Fe{sub 12.5} nanoquasicrystals

Inverse Hall-Petch (IHP) behavior in nano-quasicrystalline Al{sub 62.5}Cu{sub 25}Fe{sub 12.5} is reported. Powders with varying grain sizes were produced by mechanical milling of spray-formed quasicrystals. The hardness of the milled powders increased with decreasing grain size down to about 40 nm and decreased with further refinement, demonstrating the IHP behavior. This critical grain size was found to be larger compared to other metallic nanocrystalline alloys. This IHP behaviour has been attributed to the structural complexity in quasicrystals and to thermally activated shearing events of atoms at the grain boundaries.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Study on Interfacial Phenomena in Aluminum–Aluminum Bimetal Fabricated by Extrusion at Different Temperatures

Aluminum–aluminum bimetal was prepared by spray-formed Al22Si alloy and ZL102 through extrusion process under solid–solid state, semisolid state and solid–liquid state. The microstructures and bonding strength of the bimetallic interface were studied, and the fracture behaviors of different bimetallic states were compared. The results showed that perfect metallic bond is produced through the semisolid extrusion process. The bimetal through solid–solid extrusion process is a large number of particles extruding through gaps among the cracked oxide layers, thus realized the metallurgical combination with the virgin metal. The process of semisolid extrusion is to break the oxide film under the temperature and pressure to achieve the bimetallic bonding. Besides, the hard particles wrapped by liquid metal can also enhance bonding strength. The tensile strength of bimetal fabricated by semisolid extrusion shows more promising results than that made by solid–solid combination and solid–liquid combination; the tensile strength improved from 83.3 to 120.5 MPa, an increase of about 45%. The process presented in this study provides a promising and effective approach for achieving Al22Si/Zl102 bimetal with high-quality metallurgical bonded interface.

36 MATERIALS SCIENCE↗

Effect of tube processing methods on the texture and grain boundary characteristics of 14YWT nanostructured ferritic alloys

In this paper, texture and microstructure of tubes and plates fabricated from a nanostructured ferritic alloy (14YWT), produced either by spray forming followed by hydrostatic extrusion (Process I) or hot extrusion and cross-rolling a plate followed by hydrostatic tube extrusion (Process II) have been characterized in terms of their effects on texture and grain boundary character. Hydrostatic extrusion results in a combination of plane strain and shear deformations which generate low intensity α- and γ-fiber components of {001}<110> and {111}<110> together with a weak ζ-fiber component of {011}<211> and {011}<011>. In contrast, multi-step plane strain deformation by hot extrusion and cross-rolling of the plate leads to a strong texture component of {001}<110> together with a weaker {111}<112> component. Although the total strains are similar, shear dominated deformation leads to much lower texture indexes compared to plane strain deformations. Further, the texture intensity decreases after hydrostatic extrusion of the alloy plate formed by plane strain deformation, due to a lower number of activated slip systems during shear dominated deformation. Finally and notably, hot extruded and cross-rolled plate subjected to plane strain deformation to ~50% engineering strain creates only a modest population of low angle grain boundaries, compared to the much larger population observed following the combination of plane strain and shear deformation of ~44% engineering strain resulting from subsequent hydrostatic extrusion.

36 MATERIALS SCIENCE↗

Materials for High-Pressure Fuel Injection Systems

The high-level goal of this multi-year effort was to facilitate the Advanced Combustion Engine goal of 20% improvement (compared to 2009 baseline) of commercial engine efficiency by 2015. A sub-goal is to increase the reliability of diesel fuel injectors by investigating modelbased scenarios that cannot be achieved by empirical, trial and error methodologies alone. During this three-year project, ORNL developed the methodology to evaluate origins and to record the initiation and propagation of fatigue cracks emanating from holes that were electrodischarge machined (EDM), the method used to form spray holes in fuel injector tips. Both x-ray and neutron-based methods for measuring residual stress at four different research facilities were evaluated to determine which, if any, was most applicable to the fuel injector tip geometry. Owing to the shape and small volumes of material involved in the sack area, residual stress data could only be obtained in the walls of the nozzle a few millimeters back from the tip, and there was a hint of only a small compressive stress. This result was consistent with prior studies by Caterpillar. Residual stress studies were suspended after the second year, reserving the possibility of pursuing this in the future, if and when methodology suitable for injector sacks becomes available. The smooth specimen fatigue behavior of current fuel injector steel materials was evaluated and displayed a dual mode initiation behavior. At high stresses, cracks started at machining flaws in the surface; however, below a critical threshold stress of approximately 800 MPa, cracks initiated in the bulk microstructure, below the surface. This suggests that for the next generation for high-pressure fuel injector nozzles, it becomes increasingly important to control the machining and finishing processes, especially if the stress in the tip approaches or exceeds that threshold level. Fatigue tests were also conducted using EDM notches in the gage sections. Compared to the smooth specimens, EDM notching led to a severe reduction in total fatigue life. A reduction in fatigue life of nearly four orders of magnitude can occur at an EDM notch the approximate size of fuel injector spray holes. Consequently, the initiation and propagation behavior of cracks from small spray holes is relevant for generation of design quality data for the next generation diesel fuel injection devices. This is especially true since the current design methodologies usually rely on the less conservative smooth specimen fatigue testing results, and since different materials can have varying levels of notch fatigue resistance.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Transmitted wave measurements in cold sprayed materials under dynamic compression

Spray-formed materials have complex microstructures which pose challenges for microscale and mesoscale modeling. To constrain these models, experimental measurements of wave profiles when subjecting the material to dynamic compression are necessary. The use of a gas gun to launch a shock into a material is a traditional method to understand wave propagation and provide information of time-dependent stress variations due to complex microstructures. This data contains information on wave reverberations within a material and provides a boundary condition for simulation. Here we present measurements of the wavespeed and wave profile at the rear surface of tantalum, niobium, and a tantalum/niobium blend subjected to plate impact. Measurements of the Hugoniot elastic limit are compared to previous work and wavespeeds are compared to longitudinal sound velocity measurements to examine wave damping due to the porous microstructure.

36 MATERIALS SCIENCE↗

Deposition and post-processing techniques for transparent conductive films

In one embodiment, a method is provided for fabrication of a semitransparent conductive mesh. A first solution having conductive nanowires suspended therein and a second solution having nanoparticles suspended therein are sprayed toward a substrate, the spraying forming a mist. The mist is processed, while on the substrate, to provide a semitransparent conductive material in the form of a mesh having the conductive nanowires and nanoparticles. The nanoparticles are configured and arranged to direct light passing through the mesh. Connections between the nanowires provide conductivity through the mesh.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Deposition and post-processing techniques for transparent conductive films

In one embodiment, a method is provided for fabrication of a semitransparent conductive mesh. A first solution having conductive nanowires suspended therein and a second solution having nanoparticles suspended therein are sprayed toward a substrate, the spraying forming a mist. The mist is processed, while on the substrate, to provide a semitransparent conductive material in the form of a mesh having the conductive nanowires and nanoparticles. The nanoparticles are configured and arranged to direct light passing through the mesh. Connections between the nanowires provide conductivity through the mesh.

36 MATERIALS SCIENCE↗

Compression ignition engine having fuel system for non-sooting combustion and method

A direct injection compression ignition internal combustion engine includes a fuel system having a nozzle extending into a cylinder of the engine and a plurality of spray orifices formed in the nozzle. Each of the spray orifices has an inner diameter dimension of about 0.09 mm or less, and define inter-orifice angles between adjacent spray orifice center axes of about 36.degree. or greater such that spray plumes of injected fuel from each of the spray orifices combust within the cylinder according to a non-sooting lifted flame and gas entrainment combustion pattern. Related methodology is also disclosed.

33 ADVANCED PROPULSION SYSTEMS↗

Effects of radiation on spray flame characteristics and soot formation

Two-dimensional numerical simulations are applied to spray flames formed in a laminar counterflow and the effects of radiation on spray flame characteristics and soot formation are studied. N-Decane (C{sub 10}H{sub 22}) is used as the liquid fuel, and the droplet motion is calculated by the Lagrangian method. A single-step global reaction is employed for the combustion reaction model. A kinetically based soot model with a flamelet model is used to predict soot formation. Radiation is taken into account using the discrete ordinate method. The results show that radiation strongly affects the spray flame behavior and soot formation. Without the radiation model, flame temperature and soot volume fraction are greatly overestimated. The soot is formed in the diffusion flame regime, and its radiation emission increases with the increase in the equivalence ratio of the droplet fuel. This trend is in good agreement with that of the luminous flame behavior observed in the experiments. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Maintaining Hydrophobic Drug Supersaturation in a Micelle Corona Reservoir

In this work, two poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide) (PND) statistical copolymers and a series of three poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide)- b-polystyrene (PND-b-PS-C12) diblock polymers were synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization, in which the molecular weight of the thermoresponsive PND corona block was held constant while the polystyrene core block length was varied. The corona thickness and density of the micelles in phosphate-buffered saline (PBS, pH = 6.5) were quantified by a combination of dynamic light scattering (DLS) and small-angle X-ray scattering (SAXS). Two hydrophobic model drugs, phenytoin and nilutamide, were used to examine the drug-polymer interactions in aqueous solution. Intermolecular interactions between the diblock polymer micelle corona and both drugs were revealed by 2D 1H nuclear Overhauser effect spectroscopy (NOESY). The drug-polymer “binding” strength, quantified by diffusion ordered NMR spectroscopy (DOSY), increased as corona density of the diblock polymer micelle increased for both drugs. The in vitro dissolution of the amorphous solid dispersions was systematically investigated as a function of drug type, drug loading, and the solution-state assembly of the polymers by using either a selective or nonselective spray drying solvent. Forming micelles prior to spray drying significantly enhanced phenytoin dissolution and supersaturation maintenance for the diblock polymers by storing the drug molecules in the corona.

60 APPLIED LIFE SCIENCES↗

Open-air spray deposition of PCBM/BCP electron transport layer for inverted perovskite solar cells

A [6,6]-phenyl C61 butyric acid methyl ester (PCBM) and bathocuproine (BCP) electron transport layer (ETL) is spray deposited in open air directly on top of a perovskite at linear speeds of 9 m/min. The PCBM precursor ink contains a binary mixture of 1:1 chlorobenzene:chloroform, which optimizes spray wettability on the perovskite surface and allows quick solvent evaporation. A near-infrared heating module additionally provides a flash cure (<5 s) for the formation of smooth, large-area PCBM films (∼20 cm 2 ). A BCP solution in isopropanol is subsequently sprayed to form an ultrathin (<5 nm) film and characterized with a suite of high-resolution metrologies. The spray-deposition processing and near-infrared treatment do not damage the underlying perovskite. Inverted architecture devices containing the sprayed ETL achieve a champion efficiency of 20.3% and demonstrate stable performance without additional interlayers or surface treatments. Here, the technoeconomic cost of the open-air spray process is compared against traditional vacuum-based evaporation, resulting in a decrease in manufacturing costs by 26%.

14 SOLAR ENERGY↗

A numerical framework for simulating the atmospheric variability of supermicron marine biogenic ice nucleating particles

Abstract. We present a framework for estimating concentrations of episodically elevated high-temperature marine ice nucleating particles (INPs) in the sea surface microlayer and their subsequent emission into the atmospheric boundary layer. These episodic INPs have been observed in multiple ship-based and coastal field campaigns, but the processes controlling their ocean concentrations and transfer to the atmosphere are not yet fully understood. We use a combination of empirical constraints and simulation outputs from an Earth system model to explore different hypotheses for explaining the variability of INP concentrations, and the occurrence of episodic INPs, in the marine atmosphere. In our calculations, we examine the following two proposed oceanic sources of high-temperature INPs: heterotrophic bacteria and marine biopolymer aggregates (MBPAs). Furthermore, we assume that the emission of these INPs is determined by the production of supermicron sea spray aerosol formed from jet drops, with an entrainment probability that is described by Poisson statistics. The concentration of jet drops is derived from the number concentration of supermicron sea spray aerosol calculated from model runs. We then derive the resulting number concentrations of marine high-temperature INPs (at 253 K) in the atmospheric boundary layer and compare their variability to atmospheric observations of INP variability. Specifically, we compare against concentrations of episodically occurring high-temperature INPs observed during field campaigns in the Southern Ocean, the Equatorial Pacific, and the North Atlantic. In this case study, we evaluate our framework at 253 K because reliable observational data at this temperature are available across three different ocean regions, but suitable data are sparse at higher temperatures. We find that heterotrophic bacteria and MBPAs acting as INPs provide only a partial explanation for the observed high INP concentrations. We note, however, that there are still substantial knowledge gaps, particularly concerning the identity of the oceanic INPs contributing most frequently to episodic high-temperature INPs, their specific ice nucleation activity, and the enrichment of their concentrations during the sea–air transfer process. Therefore, targeted measurements investigating the composition of these marine INPs and drivers for their emissions are needed, ideally in combination with modeling studies focused on the potential cloud impacts of these high-temperature INPs.

54 ENVIRONMENTAL SCIENCES↗