Results for “Steel scrap” — Page 2

DOE OSTI2020

Malleable Thermosets (Vitrimers) from CO 2 and Plants

Fiber-reinforced composite materials are increasingly used to replace heavy metal components in transportation applications for lightweighting purposes. Polymer matrix materials used in automotive parts, such as epoxies, nylons, and polypropylenes, are almost all produced from fossil fuels. Higher performance thermoset composites are generally not repairable and lower-cost thermoplastic composites do not have enough performance to replace steel. Vitrimers are a new class of polymer materials with long shelf life, low waste in production, ease of processing, and repairability that have the potential to break through the high-cost thermoset/low-performance thermoplastic barrier to vehicle light-weighting. Vitrimers also exhibit easier chemical recyclability than conventional thermosets with reversible chemical crosslinking that enables reprocessing of scrap from production and end of life components. Vitrimers are a new class of engineered plastics that are weldable, repairable and recyclable like thermoplastics but have high mechanical properties like thermosets. Bio-based vitrimers have only recently been reported in the academic and patent literature. These materials represent an unusual opportunity to meet both VTO light-weighting targets for low-density, high performance materials and BETO sustainability targets for value-added high-volume applications of bio-fuel byproducts. Also, PNNL researchers have previously demonstrated a process to convert CO 2 into potential vitrimer precursors. Washington State University (WSU) success in demonstration of bio-based vitrimers and recent steps toward commercialization of petroleum-based vitrimers support the opportunity for PNNL success in development of sustainable vitrimer materials for recyclable, high-performance fiber-reinforced composites for the transportation sectors.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Recent progress in the design of the K-DEMO divertor

The preliminary conceptual design of the Korean fusion demonstration reactor (K-DEMO) with a major radius of 6.8 m and the fusion power of 2200 MW has been studied since 2012. The overall configuration of the K-DEMO divetor system based on the ITER-like water-cooled tungsten technology is a double-null type symmetric divertor subdivided into 32 toroidal modules for the vertical maintenance. A detached divertor scenario with impurity seeding was considered as the primary approach for the power exhaust to reduce the peak heat flux lower than the engineering limit of 10 MW/m 2 . The power exhaust performance at the scrap off layer was estimated by using UEDGE-2D code, a two-dimensional fluid transport code for collisional edge plasma and neutral species like N, Ne, and Ar. Particle and heat flux on inboard and outboard divertor targets were calculated for the detached cased depending on parameters such as the impurity seeding rate, pumping rate, and the pedestal density. On the other hand, a magnetic solution like X-divertor, snowflake divertor, and super X-divertor to expand the plasma wet area was considered for K-DEMO since the detached divertor increasing a radiation fraction by impurity seeding might be able to be unstable. However, the extremely high current of poloidal coils was required more than the engineering limit, 20 MA, to form magnetic field lines for the alternative divertors. Based on the physical calculation of the edge plasma, engineering analyses were carried out to find out the thermal and structural reliability. The thermo-hydraulic analysis confirmed thermal stability, whether all comprising materials are operating within their allowable temperature windows when the case of the peak heat flux is set to 10 MW/m 2 on the outboard divertor target. The response surface optimization method derived two optimal design candidates employing two kinds of heat sink materials, respectively: the reduced activation ferritic martensitic (RAFM) steel and CuCrZr alloy. Additionally, the drawbacks and merits of the two materials were definite. The optimal design with applying RAFM steel was vulnerable to withstand thermal and mechanical loads since low thermal conductivity caused too thin thickness of the heat sink. On the other hand, the CuCrZr alloy has critical drawbacks in terms of activation and radioactive waste despite its high thermal conductivity. Meanwhile, preliminary electromagnetic (EM) analysis was carried out to estimate the EM loads caused by the abnormal behaviors of plasma since EM loads are one of the most critical external loads for designing a DEMO divertor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗