Search NASA⌕ Search

SEARCH · Search NASA

Results for “Struts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

A numerical investigation of supersonic strut/endwall interactions in annular flow with varying strut thickness

A full 3D Navier-Stokes numerical investigation has been conducted of the shock-wave/boundary-layer flow interactions caused by four diamond-shaped struts, of varying thickness, in an annular duct with Mach 3 core flow and turbulent boundary-layers on both walls. Secondary flows caused by weak-to-strong interactions are examined in the vicinity of a strut which is bounded by curved endwalls. The duct endwall boundary-layer separated for the strongest interaction. The struts studied had maximum thickness-to-chord ratios of 0.125, 0.188, 0.250, and 0.500. The duct gap height is 0.7 strut chords, the duct inner-to-outer wall radius ratio is 0.7, and the Reynolds number is 3 x 10 exp 5 based on the strut chord length which was held constant for all interactions considered. The effects of strut thickness on the secondary flows are discussed, including: trajectories for the leading and trailing edge horseshoe vortices, strut/endwall corner vortices, and boundary-layer separation. The line of coalescence discussed in the literature, previously ascribed to boundary-layer separation, is shown to be caused by the leading edge horseshoe vortex convecting along the shock front.

Williams, K. E.↗

Flexible Wing Model for Structural Sizing and Multidisciplinary Design Optimization of a Strut-Braced Wing

This paper describes a structural and aeroelastic model for wing sizing and weight calculation of a strut-braced wing. The wing weight is calculated using a newly developed structural weight analysis module considering the special nature of strut-braced wings. A specially developed aeroelastic model enables one to consider wing flexibility and spanload redistribution during in-flight maneuvers. The structural model uses a hexagonal wing-box featuring skin panels, stringers, and spar caps, whereas the aerodynamics part employs a linearized transonic vortex lattice method. Thus, the wing weight may be calculated from the rigid or flexible wing spanload. The calculations reveal the significant influence of the strut on the bending material weight of the wing. The use of a strut enables one to design a wing with thin airfoils without weight penalty. The strut also influences wing spanload and deformations. Weight savings are not only possible by calculation and iterative resizing of the wing structure according to the actual design loads. Moreover, as an advantage over the cantilever wing, employment of the strut twist moment for further load alleviation leads to increased savings in structural weight.

Gern, Frank H.↗

Design of Structurally Efficient Tapered Struts (SETS)

A study was conducted to develop mass efficient composite struts. A closed-form design methodology for composite struts was developed using well established analyses to predict Euler buckling, local wall buckling; compression strength, damage tolerance, and interlaminar shear at geometric gradients. The methodology was coded in a spreadsheet suitable for convenient and rapid sizing of tapered composite struts. This spreadsheet analysis was used to determine the influence of several variables such as material stiffness, strut diameter, and material allowables on strut weight for given loading conditions. The comparison showed that, while the Park Aerospace design method was well suited to preliminary sizing for a conservative design, the closed-form-analyses-based spreadsheet accounts for all possible failure modes and is a good optimum strut design tool. The report concludes with a set of recommendations for future work in analytical design and analysis methodology enhancements.

Ravi Deo↗

Metering Gas Strut for Separating Rocket Stages

A proposed gas strut system would separate a liquid-fueled second rocket stage from a solid-fueled first stage using an array of pre-charged struts. The strut would be a piston-and-cylinder mechanism containing a compressed gas. Adiabatic expansion of the gas would drive the extension of the strut. The strut is designed to produce a force-versus-time profile, chosen to prevent agitation of the liquid fuel, in which the force would increase from an initial low value to a peak value, then decay toward the end of the stroke. The strut would include a piston chamber and a storage chamber. The piston chamber would initially contain gas at a low pressure to provide the initial low separation force. The storage chamber would contain gas at a higher pressure. The piston would include a longitudinal metering rod containing an array of small holes, sized to restrict the flow gas between the chambers, that would initially not be exposed to the interior of the piston chamber. During subsequent expansion, the piston motion would open more of the metering holes between the storage and piston chambers, thereby increasing the flow of gas into the piston chamber to produce the desired buildup of force.

Floyd, Brian↗

Development Testing and Subsequent Failure Investigation of a Spring Strut Mechanism

Commodities are transferred between the Multi-Purpose Crew Vehicle (MPCV) crew module (CM) and service module (SM) via an external umbilical that is driven apart with spring-loaded struts after the structural connection is severed. The spring struts must operate correctly for the modules to separate safely. There was no vibration testing of strut development units scoped in the MPCV Program Plan; therefore, any design problems discovered as a result of vibration testing would not have been found until the component qualification. The NASA Engineering and Safety Center (NESC) and Lockheed Martin (LM) performed random vibration testing on a single spring strut development unit to assess its ability to withstand qualification level random vibration environments. Failure of the strut while exposed to random vibration resulted in a follow-on failure investigation, design changes, and additional development tests. This paper focuses on the results of the failure investigations including identified lessons learned and best practices to aid in future design iterations of the spring strut and to help other mechanism developers avoid similar pitfalls.

Dervan, Jared↗

Critical impact of experimentally-driven strut level anisotropic material models in advanced stress analysis of additively manufactured lattice structures

The rapid acceleration in materials discovery may overshadow the importance of thoroughly understanding the mechanical performance of newly developed materials in demanding environments. The recent interest in combining parametric studies with machine learning techniques to explore how changes in specific processing parameters or model inputs affect the overall behavior of a material system can only be truly beneficial if the governing constitutive relations describing material behavior are accurately established. In this study, we demonstrate the critical impact of accurately representing strut-level anisotropic material behavior in advanced stress analysis of additively manufactured lattice structures (AMLS). We introduce a systematic experimental and modeling approach for developing strut-level anisotropic elastoplastic material models that account for the influence of microstructural features such as porosity, texture, and surface roughness on the development of local anisotropic mechanical properties, which vary with strut orientation relative to the build direction (BD). As a result the presented material model captures and relates the statistics of spatially varying struts’ microstructural features to the local stress distribution. Our findings suggest that incorporating strut-level anisotropic material behavior into unit cell analysis significantly influences the load distribution and evolution of local stresses within the structure. Therefore, accounting for this anisotropy is critical for developing an understanding of unit cell behavior and performance, including subsequent topology/component design optimization based on this analysis.

Sahoo, Subhadip [University of Arizona]↗

Direct-connect test of a hydrogen-fueled three-strut injector for an integrated modular scramjet engine

The study aims at illustrating the effects of strut and injector interactions and strut wakes not totally simulated in previous, less complex, direct-connect hardware. In addition, the influence of the relative location of the injectors on opposite sides of each strut and the effect of injector spacing are evaluated. It is shown that better mixing efficiency is attained by locating the fuel injectors on opposite sides of a strut so that the jets come together, rather than being staggered, in the strut wake. It is not possible to determine the combustion efficiency by means of a one-dimensional analysis of the wall pressure.

Mcclinton, C. R.↗

Characterization of a swept-strut hydrogen fuel-injector for scramjet applications

Results of an experimental investigation of a swept-strut hydrogen fuel-injector simulating the center strut of a three strut scramjet module at Mach 6 flight conditions are presented. Detailed wall pressure distributions from over 100 separate tests with overall fuel flow from 0.1 to 1.3 times stoichiometric and test gas stagnation temperature from 1100 to 2400 K were recorded. The distance for pressure rise from the point of injection was found to increase with increasing test stagnation temperature. This trend indicates that chemical kinetics in the immediate region of perpendicular injection are not likely to be the mechanism controlling the onset of pressure rise. A fluid dynamic mechanism is suggested involving separation of the boundary layer downstream of injection which is forced upstream from the trailing edge by pressure rise due to combustion occurring in the base region of the strut. The results obtained indicate that the swept-strut fuel-injector concept can be adapted to a wide range of flight conditions by varying the amount of perpendicular fuel injection.

Northam, G. B.↗

Test and evaluate passive orbital disconnect struts (PODS 3)

The objectives of the Passive Orbital Disconnect Struts (PODS) test are to evaluate modal resonance of the PODS-III supports to obtain engineering data required for use of PODS-III on flight systems; determine possible performance improvements in large LO2/LH2 space applications. (1) Modal Vibration Tests. A modal resonance survey is performed on a set of six PODS-III struts assembled in a dewar simulator. The survey conditions simulate both launch and orbital loadings of the struts. The orbital load range spans a full to an empty tank. The frequencies surveyed cover the range consistent with Shuttle qualification requirements and the principal resonant modes of the strut system. (2) Benefit study. The benefit of using PODS-III supports on OTV and Space Station LO sub 2 and LH sub 2 reference tanks was compared to nondisconnect supports. Four LO sub 2 and LH sub 2 tanks were studied under various conditions: (1) holding the launch resonance at 35 Hz and varying the orbit resonance; (2) analyzing both full and emtpy tanks at launch; (3) varying orbit boundary temperaure; (4) varying the number of struts; (5) varying orbit times; and (6) using or not using vapor cooling.

Parmley, R. T.↗

Experimental investigation of unsteady fan flow interaction with downstream struts

In the present study of the unsteady pressure field produced on fan rotor blades by interaction with downstream struts, a single stage, low speed axial-flow fan was instrumented with blade-mounted high frequency pressure transducers. In addition, stationary pressure problems were used to map out the flowfield. Fluctuating pressure measurements are presented for blade midspan and 85-percent span on both the suction and pressure surfaces of the rotor blades at several positions of the downstream struts, and for two different flow coefficients. The strut is found to produce an effect on the unsteady pressure field on the rotor blades; this effect exceeds that due to the stator at design rotor-stator-strut spacing, but it rapidly declines as the struts are moved downstream.

Ng, W. F.↗

Process development and fabrication of space station type aluminum-clad graphite epoxy struts

The manufacture of aluminum-clad graphite epoxy struts, designed for application to the Space Station truss structure, is described. The strut requirements are identified, and the strut material selection rationale is discussed. The manufacturing procedure is described, and shop documents describing the details are included. Dry graphite fiber, Pitch-75, is pulled between two concentric aluminum tubes. Epoxy resin is then injected and cured. After reduction of the aluminum wall thickness by chemical milling the end fittings are bonded on the tubes. A discussion of the characteristics of the manufactured struts, i.e., geometry, weight, and any anomalies of the individual struts is included.

Ring, L. R.↗

Design, analysis, and testing of high frequency passively damped struts

Objectives of the research are: (1) to develop design requirements for damped struts to stabilize control system in the high frequency cross-over and spill-over range; (2) to design, fabricate and test viscously damped strut and viscoelastically damped strut; (3) to verify accuracy of design and analysis methodology of damped struts; and (4) to design and build test apparatus, and develop data reduction algorithm to measure strut complex stiffness. In order to meet the stringent performance requirements of the SPICE experiment, the active control system is used to suppress the dynamic responses of the low order structural modes. However, the control system also inadvertently drives some of the higher order modes unstable in the cross-over and spill-over frequency range. Passive damping is a reliable and effective way to provide damping to stabilize the control system. It also improves the robustness of the control system. Damping is designed into the SPICE testbed as an integral part of the control-structure technology.

Yiu, Y. C.↗

Impact damage tolerance of thin wall composite struts

An experimental investigation was made to study the impact damage tolerance of thin wall composite struts made of both brittle epoxy and toughened epoxy based composite materials. Damage parameters such as barely visible surface damage and internal damage represented by the ultrasonic C-scan, and residual compressive strengths were evaluated against impact energy for two impactor sizes. From both a damage resistance (internal damage vs. impact energy) and a damage tolerance (residual compressive strength vs. internal damage) point of view, the toughened IM7/977-2 struts exhibited better performance than the brittle epoxy based T50/934 struts. This is attributed to the toughening mechanism in 977-2 which impedes delamination initiation from impact, and delamination growth and subsequent buckling under a compression loading. At barely visible damage thresholds, regardless of the impactor sizes, a maximum strength reduction of 45-55 percent was observed for the T50/934 struts, and approximately 10 percent for IM7/977-2 struts. This is of great interest for developing a damage tolerance design approach and risk assessment methodology in which the design allowable would be defined by the residual strength at the threshold of barely visible damage.

Chen, G.-S.↗

Design of Structurally Efficient Tapered Struts

This report describes the analytical study of two full-scale tapered composite struts. The analytical study resulted in the design of two structurally efficient carbon/epoxy struts in accordance with NASA-specified geometries and loading conditions. Detailed stress analysis was performed of the insert, end fitting, and strut body to obtain an optimized weight with positive margins. Two demonstration struts were fabricated based on a well-established design from a previous Space Shuttle strut development program.

Messinger, Ross↗

Investigation of Transonic Truss-Braced Wing Aircraft Transonic Wing-Strut Interference Effects Using FUN3D

This paper presents a computational study of transonic wing-strut interference effects of Transonic Truss-Braced Wing (TTBW) aircraft using the high-fidelity CFD (Computational Fluid Dynamics) code FUN3D (Fully Unstructured Navier-Stokes Three Dimensional). The study is conducted for the wing-strut and the wing-alone configurations at different Mach numbers and Reynolds numbers. The interference effects are calculated by comparing the wing aerodynamics along the spanwise direction between the wing-strut and the wing-alone configurations. The presence of the strut underneath the wing induces a suction peak on the lower surface of the wing, which causes changes in aerodynamic forces and moments, as well as the aerodynamic center location. The interference effects become more pronounced as the Mach number increases. The Reynolds number has less impact on the interference effects. A transonic wing-strut interference aerodynamic correction method is developed for use in a lower-fidelity tool, VSPAERO [a vortex lattice flow solver], coupled to a finite-element model for rapid flutter analysis.

Xiong, Juntao↗

Study of Mach 0.8 Transonic Truss-Braced Wing Aircraft Wing-Strut Interference Effects

This paper presents computational study of transonic wing-strut interference effects of the Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft using the high-fidelity CFD solver FUN3D. The study is conducted for the wing-strut and the wing-alone configurations at design Mach number0.8 and Reynolds number14.0 ́106.The interference effects are calculated by comparing the wing aerodynamics along the spanwise direction between the wing-strut and the wing-alone configurations. The presence of the strut underneath the wing induces a suction peak on the lower surface of the wing, which causes changes in aerodynamic forces and moments. The interference effects of the Mach 0.8 TTBW aircraft are compared with the Mach 0.745 TTBW aircraft. A transonic wing-strut interference aerodynamic correction model is developed for use in a lower-fidelity tool, VSPAERO, for rapid aerodynamic analysis of the Mach 0.8 TTBW aircraft.

TTBW↗

Aircraft with strut-braced wing system

Described herein is an aircraft. The aircraft comprises a body. The aircraft also comprises a wing coupled to and extending from the body. The wing comprises a wing inboard end portion, a wing outboard end portion, opposite the wing inboard end portion, and an intermediate portion between the wing inboard end portion and the wing outboard end portion. The aircraft further comprises a strut. The strut comprises a strut inboard end portion coupled to and extending from the body and a strut outboard end portion coupled to and extending from the intermediate portion of the wing. The aircraft additionally comprises at least one aerodynamic control surface movably coupled to the strut.

Harrison, Neal A.↗

Detecting missing struts in metallic micro-lattices using high speed melt pool thermal monitoring

Metal lattices are an important class of cellular materials that offer great advantages by providing high-strength and lightweight structures as compared to bulk materials. Progress in additive manufacturing techniques has led to increased complexity in design and shape of produced objects and is greatly beneficial for the development of metallic lattice structures. However additive manufacturing of lattices suffers from unpredictable defect creation that can compromise its mechanical integrity. Although post-build inspection techniques can provide quality assurance of the process, accurate assessment can be technically challenging, time consuming and costly. In this work, we investigate the use of high-speed measurements of thermal emission from the melt pool to identify defective individual struts formed with a missing bottom half in an otherwise fully built lattice structure produced with laser powder bed fusion. Surprisingly, results indicate lower photodiode signal, suggesting colder melt pool surface temperature, when printing struts with missing bottom half as compared to nominal struts. Additional thermographic imaging and multi-physics simulations reveal that the low photodiode signal is accompanied by presence of hot spatters carrying heat away from detection and continuous avalanche of powder on the melt pool. Based on these observations, a method was developed to identify defective individual struts with missing bottom half in full built lattices. This prediction approach provides valuable insights about part quality which are important for process qualification and illustrates the utility of melt pool thermal emission monitoring for identifying specific defects introduced by laser powder bed fusion.

36 MATERIALS SCIENCE↗