Search NASA⌕ Search

SEARCH · Search NASA

Results for “Subsonic Transports”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Program review

This report summarizes the Integrated Application of Active Controls (IAAC) Technology to an Advanced Subsonic Transport Project, established as one element of the NASA/Boeing Energy Efficient Transport Technology Program. The performance assessment showed that incorporating ACT into an airplane designed to fly approximately 200 passengers approximately 2,000 nmi could yield block fuel savings from 6 to 10 percent at the design range. The principal risks associated with incorporating these active control functions into a commercial airplane are those involved with the ACT system implementation. The Test and Evaluation phase of the IAAC Project focused on the design, fabrication, and test of a system that implemented pitch axis fly-by-wire, pitch axis augmentation, and wing load alleviation. The system was built to be flight worthy, and was planned to be experimentally flown on the 757. The system was installed in the Boeing Digital Avionics Flight Controls Laboratory (DAFCL), where open loop hardware and software tests, and a brief examination of a direct drive valve (DDV) actuation concept were accomplished. The IAAC Project has shown that ACT can be beneficially incorporated into a commercial transport airplane. Based on the results achieved during the testing phase, there appears to be no fundamental reason(s) that would preclude the commercial application of ACT, assuming an appropriate development effort is included.

Source record↗
NASA NTRS1975

Study of the application of hydrogen fuel to long-range subsonic transport aircraft, volume 2

The feasibility, practicability, and potential advantages/disadvantages of using liquid hydrogen as fuel in long range, subsonic transport aircraft of advanced design were studied. Both passenger and cargo-type aircraft were investigated. To provide a valid basis for comparison, conventional hydrocarbon (Jet A) fueled aircraft were designed to perform identical missions using the same advanced technology and meeting the same operational constraints. The liquid hydrogen and Jet A fueled aircraft were compared on the basis of weight, size, energy utilization, cost, noise, emissions, safety, and operational characteristics. A program of technology development was formulated.

Brewer, G. D.↗
NASA NTRS1975

Study of the application of hydrogen fuel to long-range subsonic transport aircraft. Volume 1: Summary

The feasibility of using liquid hydrogen as fuel in advanced designs of long range, subsonic transport aircraft is assessed. Both passenger and cargo type aircraft are investigated. Comparisons of physical, performance, and economic parameters of the LH2 fueled designs with conventionally fueled aircraft are presented. Design studies are conducted to determine appropriate characteristics for the hydrogen related systems required on board the aircraft. These studies included consideration of material, structural, and thermodynamic requirements of the cryogenic fuel tanks and fuel systems with the structural support and thermal protection systems.

Brewer, G. D.↗
NASA NTRS1982

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project. ACT/Control/Guidance System study. Volume 2: Appendices

The integrated application of active controls (IAAC) technology to an advanced subsonic transport is reported. Supplementary technical data on the following topics are included: (1) 1990's avionics technology assessment; (2) function criticality assessment; (3) flight deck system for total control and functional features list; (4) criticality and reliability assessment of units; (5) crew procedural function task analysis; and (6) recommendations for simulation mechanization.

Source record↗
NASA NTRS2010

Guidelines for Computing Longitudinal Dynamic Stability Characteristics of a Subsonic Transport

A systematic study is presented to guide the selection of a numerical solution strategy for URANS computation of a subsonic transport configuration undergoing simulated forced oscillation about its pitch axis. Forced oscillation is central to the prevalent wind tunnel methodology for quantifying aircraft dynamic stability derivatives from force and moment coefficients, which is the ultimate goal for the computational simulations. Extensive computations are performed that lead in key insights of the critical numerical parameters affecting solution convergence. A preliminary linear harmonic analysis is included to demonstrate the potential of extracting dynamic stability derivatives from computational solutions.

Thompson, Joseph R.↗
NASA NTRS1979

Accelerated development and flight evaluation of active controls concepts for subsonic transport aircraft. Volume 2: AFT C.G. simulation and analysis

Relaxed static stability and stability augmentation with active controls were investigated for subsonic transport aircraft. Analytical and simulator evaluations were done using a contemporary wide body transport as a baseline. Criteria for augmentation system performance and unaugmented flying qualities were evaluated. Augmentation control laws were defined based on selected frequency response and time history criteria. Flying qualities evaluations were conducted by pilots using a moving base simulator with a transport cab. Static margin and air turbulence intensity were varied in test with and without augmentation. Suitability of a simple pitch control law was verified at neutral static margin in cruise and landing flight tasks. Neutral stability was found to be marginally acceptable in heavy turbulence in both cruise and landing conditions.

Urie, D. M.↗
NASA NTRSDate not supplied

Subsonic-Transport Core/Combustor Noise

The presentation is an overview of the propulsion-noise contributions from sources associated with the combustor for subsonic-transport aircraft. Sections of the talk cover: the impact of future compact high-efficiency core design trends on airport-community noise, the physical source mechanisms responsible for direct and indirect combustor noise, and combustor-noise prediction and measurement. The noise issues discussed are important to future gas-turbine propulsors, to envisioned hybrid-electric aircraft propulsion systems, and represent key challenges in the strategy to develop novel propulsion systems for ultra-efficient transport aircraft. The Advanced Air Transport Technology Project supports this effort.

Aeroacoustics, Combustor Noise, Turbomachinery Noi↗
NASA NTRS1975

Evaluation of viscous drag reduction schemes for subsonic transports

The results are described of a theoretical study of viscous drag reduction schemes for potential application to the fuselage of a long-haul subsonic transport aircraft. The schemes which were examined included tangential slot injection on the fuselage and various synergetic combinations of tangential slot injection and distributed suction applied to wing and fuselage surfaces. Both passive and mechanical (utilizing turbo-machinery) systems were examined. Overall performance of the selected systems was determined at a fixed subsonic cruise condition corresponding to a flight Mach number of free stream M = 0.8 and an altitude of 11,000 m. The nominal aircraft to which most of the performance data was referenced was a wide-body transport of the Boeing 747 category. Some of the performance results obtained with wing suction are referenced to a Lockheed C-141 Star Lifter wing section. Alternate designs investigated involved combinations of boundary layer suction on the wing surfaces and injection on the fuselage, and suction and injection combinations applied to the fuselage only.

Marino, A.↗
NASA NTRS1981

Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project: Current and advanced act control system definition study. Volume 2: Appendices

The current status of the Active Controls Technology (ACT) for the advanced subsonic transport project is investigated through analysis of the systems technical data. Control systems technologies under examination include computerized reliability analysis, pitch axis fly by wire actuator, flaperon actuation system design trade study, control law synthesis and analysis, flutter mode control and gust load alleviation analysis, and implementation of alternative ACT systems. Extensive analysis of the computer techniques involved in each system is included.

Hanks, G. W.↗
NASA NTRS2003

Follow-On Technology Requirement Study for Advanced Subsonic Transport

A study was conducted to define and assess the critical or enabling technologies required for a year 2005 entry into service (EIS) engine for subsonic commercial aircraft, with NASA Advanced Subsonic Transport goals used as benchmarks. The year 2005 EIS advanced technology engine is an Advanced Ducted Propulsor (ADP) engine. Performance analysis showed that the ADP design offered many advantages compared to a baseline turbofan engine. An airplane/ engine simulation study using a long range quad aircraft quantified the effects of the ADP engine on the economics of typical airline operation. Results of the economic analysis show the ADP propulsion system provides a 6% reduction in direct operating cost plus interest, with half the reduction resulting from reduced fuel consumption. Critical and enabling technologies for the year 2005 EIS ADP were identified and prioritized.

Wendus, Bruce E.↗
NASA NTRS2014

Trim and Structural Optimization of Subsonic Transport Wings Using Nonconventional Aeroelastic Tailoring

Several minimum-mass aeroelastic optimization problems are solved to evaluate the effectiveness of a variety of novel tailoring schemes for subsonic transport wings. Aeroelastic strength and panel buckling constraints are imposed across a variety of trimmed maneuver loads. Tailoring with metallic thickness variations, functionally graded materials, composite laminates, tow steering, and distributed trailing edge control effectors are all found to provide reductions in structural wing mass with varying degrees of success. The question as to whether this wing mass reduction will offset the increased manufacturing cost is left unresolved for each case.

Stanford, Bret K.↗
NASA NTRS1978

The development and evaluation of advanced technology laminar-flow-control subsonic transport aircraft

A study was conducted to evaluate the technical and economic feasibility of applying laminar flow control (LFC) to the wings and empennage of long-range subsonic transport aircraft for initial operation in 1985. For a design mission range of 5500 n mi, advanced technology LFC and turbulent-flow aircraft were developed for a 200-passenger payload, and compared on the basis of production costs, direct operating costs, and fuel efficiency. Parametric analyses were conducted to establish optimum geometry, advanced system concepts were evaluated, and configuration variations maximizing the effectiveness of LFC were developed. The final comparisons include consideation of maintenance costs and procedures, manufacturing costs and procedures, and operational considerations peculiar to LFC aircraft.

Sturgeon, R. F.↗
NASA NTRS1976

Study of the application of advanced technologies to laminar flow control systems for subsonic transports. Volume 1: Summary

A study was conducted to evaluate the technical and economic feasibility of applying laminar flow control to the wings and empennage of long-range subsonic transport aircraft compatible with initial operation in 1985. For a design mission range of 10,186 km (5500 n mi), advanced technology laminar-flow-control (LFC) and turbulent-flow (TF) aircraft were developed for both 200 and 400-passenger payloads, and compared on the basis of production costs, direct operating costs, and fuel efficiency. Parametric analyses were conducted to establish the optimum geometry for LFC and TF aircraft, advanced LFC system concepts and arrangements were evaluated, and configuration variations maximizing the effectiveness of LFC were developed. For the final LFC aircraft, analyses were conducted to define maintenance costs and procedures, manufacturing costs and procedures, and operational considerations peculiar to LFC aircraft. Compared to the corresponding advanced technology TF transports, the 200- and 400-passenger LFC aircraft realized reductions in fuel consumption up to 28.2%, reductions in direct operating costs up to 8.4%, and improvements in fuel efficiency, in ssm/lb of fuel, up to 39.4%. Compared to current commercial transports at the design range, the LFC study aircraft demonstrate improvements in fuel efficiency up to 131%. Research and technology requirements requisite to the development of LFC transport aircraft were identified.

Sturgeon, R. F.↗
NASA NTRS2016

Assessment of the Noise Reduction Potential of Advanced Subsonic Transport Concepts for NASA's Environmentally Responsible Aviation Project

Aircraft system noise is predicted for a portfolio of NASA advanced concepts with 2025 entry-into-service technology assumptions. The subsonic transport concepts include tube-and-wing configurations with engines mounted under the wing, over the wing nacelle integration, and a double deck fuselage with engines at a mid-fuselage location. Also included are hybrid wing body aircraft with engines upstream of the fuselage trailing edge. Both advanced direct drive engines and geared turbofan engines are modeled. Recent acoustic experimental information was utilized in the prediction for several key technologies. The 301-passenger class hybrid wing body with geared ultra high bypass engines is assessed at 40.3 EPNLdB cumulative below the Stage 4 certification level. Other hybrid wing body and unconventional tube-and-wing configurations reach levels of 33 EPNLdB or more below the certification level. Many factors contribute to the system level result; however, the hybrid wing body in the 301-passenger class, as compared to a tubeand- wing with conventional engine under wing installation, has 11.9 EPNLdB of noise reduction due to replacing reflection with acoustic shielding of engine noise sources. Therefore, the propulsion airframe aeroacoustic interaction effects clearly differentiate the unconventional configurations that approach levels close to or exceed the 42 EPNLdB goal.

Thomas, Russell H.↗
NASA NTRS1992

Application of advanced technologies to very large subsonic transports

A NASA-Langley study has used the interdisciplinary Flight Optimization System to examine the impact of advanced technologies on the performance and plausible size of large, long-range subsonic transport aircraft. The baseline, four-engine configuration studied would carry 412 passengers over 7300 n. mi.; the technologies evaluated encompass high aspect ratio supercritical-airfoil wings, a composite wing structure, an all-composite primary structure, and hybrid laminar flow control. The results obtained indicate that 600-passenger transports, whose takeoff gross weight is no greater than that of the 412-passenger baseline, are made possible by the new technologies.

Bartlett, Dennis W.↗
NASA NTRS1993

Technology benefits for very large subsonic transports

Results are presented for a study conducted at the NASA Langley Research Center which examined the effects of advanced technologies on the performance and size of very large, long-range subsonic transports. The study was performed using the Flight Optimization System (FLOPS). a multidisciplinary system of computer programs for conceptual and preliminary design and evaluation of advanced aircraft concepts. A four-engine, baseline configuration representative of existing transport technology was defined having a payload of 412 passengers plus baggage and a design range of 7300 nmi. New 600, 800 and 1000-passenger advanced transport concepts were then developed and compared to the baseline configuration. The technologies examined include 1995 entry-into-service (ELS) engines, high aspect ratio supercritical wings, composite materials for the wing, fuselage and empennage, and hybrid laminar flow control (HLFC). All operational and regulatory requirements and constraints, such as fuel reserves, balanced field length, and second segment climb gradient were satisfied during the design process. The effect of the advanced technologies on the size, weight and performance of the advanced transport concepts are presented. In addition, the sensitivity of the takeoff gross weight of the advanced transport concepts to increases in design range and payload, and designing for stretch capability are also discussed.

Arcara, Philip C., Jr.↗
NASA NTRS1991

Analysis for the application of hybrid laminar flow control to a long-range subsonic transport aircraft

The FLOPS aircraft conceptual design/analysis code has been used to evaluate the effects of incorporating hybrid laminar flow control (HLFC) in a 300-passenger, 6500 n. mi. range, twin-engine subsonic transport aircraft. The baseline configuration was sized to account for 50 percent chord laminar flow on the wing upper surface as well as both surfaces of the empennage airfoils. Attention is given to the additional benefits of achieving various degrees of laminar flow on the engine nacelles, and the horsepower extraction and initial weight and cost increments entailed by the HLFC system. The sensitivity of the results obtained to fuel-price and off-design range are also noted.

Arcara, P. C., Jr.↗