Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sulfur Hexafluoride”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

CO2 laser-driven Stirling engine

A 100-W Beale free-piston Stirling engine was powered remotely by a CO2 laser for long periods of time. The engine ran on both continuous-wave and pulse laser input. The working fluid was helium doped with small quantities of sulfur hexafluoride, SF6. The CO2 radiation was absorbed by the vibrational modes of the sulfur hexafluoride, which in turn transferred the energy to the helium to drive the engine. Electrical energy was obtained from a linear alternator attached to the piston of the engine. Engine pressures, volumes, and temperatures were measured to determine engine performance. It was found that the pulse radiation mode was more efficient than the continuous-wave mode. An analysis of the engine heat consumption indicated that heat losses around the cylinder and the window used to transmit the beam into the engine accounted for nearly half the energy input. The overall efficiency, that is, electrical output to laser input, was approximately 0.75%. However, this experiment was not designed for high efficiency but only to demonstrate the concept of a laser-driven engine. Based on this experiment, the engine could be modified to achieve efficiencies of perhaps 25-30%.

Lee, G.↗
NASA NTRS1986

Evaluation of a storable fluorine based pilot for scramjets

An ignitor/pilot device for scramjet engines has been tested with C2H4, C2H6, and CH4 gaseous hydrocarbon fuels at Mach 2. The pilot was designed to operate with storable nontoxic propellants rather than hazardous pyrophorics; the pilot fluid is a mixture of ethylene, oxygen, and sulfur hexafluoride. The pilot reduced the minimum temperature at which all three hydrocarbon fuels ignited; a comparison was then conducted between combustion efficiency calculations for these test results and those of pilots using nitrogen in place of sulfur hexafluoride, and using silane-hydrogen (yielding equivalent energy). The nitrogen-substituted pilot exhibited the highest efficiency.

Diskin, G. S.↗
NASA NTRS2000

Reduced xenon diffusion for quantitative lung study--the role of SF(6)

The large diffusion coefficients of gases result in significant spin motion during the application of gradient pulses that typically last a few milliseconds in most NMR experiments. In restricted environments, such as the lung, this rapid gas diffusion can lead to violations of the narrow pulse approximation, a basic assumption of the standard Stejskal-Tanner NMR method of diffusion measurement. We therefore investigated the effect of a common, biologically inert buffer gas, sulfur hexafluoride (SF(6)), on (129)Xe NMR and diffusion. We found that the contribution of SF(6) to (129)Xe T(1) relaxation in a 1:1 xenon/oxygen mixture is negligible up to 2 bar of SF(6) at standard temperature. We also measured the contribution of SF(6) gas to (129)Xe T(2) relaxation, and found it to scale inversely with pressure, with this contribution approximately equal to 1 s for 1 bar SF(6) pressure and standard temperature. Finally, we found the coefficient of (129)Xe diffusion through SF(6) to be approximately 4.6 x 10(-6) m(2)s(-1) for 1 bar pressure of SF(6) and standard temperature, which is only 1.2 times smaller than the (129)Xe self diffusion coefficient for 1 bar (129)Xe pressure and standard temperature. From these measurements we conclude that SF(6) will not sufficiently reduce (129)Xe diffusion to allow accurate surface-area/volume ratio measurements in human alveoli using time-dependent gas diffusion NMR.

Non-NASA Center↗
DOE OSTI2025

SF6 / Acetone Separation & Purification

Sulfur hexafluoride (SF₆) is recognized as the most potent greenhouse gas used in the power transmission and semiconductor sectors. In the past decade, its global emissions have increased sharply, largely due to the absence of effective disposal and recovery pathways. This concern was formally addressed under the Kyoto Protocol, which urged participating nations to adopt measures to limit SF₆ emissions and mitigate its role in climate change. In recent years, various abatement strategies have been explored, including non-thermal plasma (NTP) technologies such as radio frequency, microwave, dielectric barrier discharge, and electron beam systems. While these methods can decompose SF₆, they also produce hazardous by-products like sulfur oxyfluorides, sulfur dioxide, hydrofluoric acid, and fluorine gas. Because these compounds pose both environmental and health risks, replacing traditional disposal practices with modern, more effective treatment methods has become an urgent priority.

36 MATERIALS SCIENCE↗
NASA NTRS2014

Design and Preliminary Performance Testing of Electronegative Gas Plasma Thruster

In classical gridded electrostatic ion thrusters, positively charged ions are generated from a plasma discharge of noble gas propellant and accelerated to provide thrust. To maintain overall charge balance on the propulsion system, a separate electron source is required to neutralize the ion beam as it exits the thruster. However, if high-electronegativity propellant gases (e.g., sulfur hexafluoride) are instead used, a plasma discharge can result consisting of both positively and negatively charged ions. Extracting such electronegative plasma species for thrust generation (e.g., with time-varying, bipolar ion optics) would eliminate the need for a separate neutralizer cathode subsystem. In addition for thrusters utilizing a RF plasma discharge, further simplification of the ion thruster power system may be possible by also using the RF power supply to bias the ion optics. Recently, the PEGASES (Plasma propulsion with Electronegative gases) thruster prototype successfully demonstrated proof-of-concept operations in alternatively accelerating positively and negatively charged ions from a RF discharge of a mixture of argon and sulfur hexafluoride.i In collaboration with NASA Marshall Space Flight Center (MSFC), the Georgia Institute of Technology High-Power Electric Propulsion Laboratory (HPEPL) is applying the lessons learned from PEGASES design and testing to develop a new thruster prototype. This prototype will incorporate design improvements and undergo gridless operational testing and diagnostics checkout at HPEPL in April 2014. Performance mapping with ion optics will be conducted at NASA MSFC starting in May 2014. The proposed paper discusses the design and preliminary performance testing of this electronegative gas plasma thruster prototype.

Liu, Thomas M.↗
DOE OSTI2024

Industry Scan of Non-SF6 Gas-Insulated Technologies

Sulfur Hexafluoride (SF 6 ) is a specialty gas with excellent electrical insulation properties which has been used extensively in the power industry. This gas is unfortunately also one of the most potent greenhouse gases known to humanity. A 2014 report by the Intergovernmental Panel on Climate Change found that SF 6 has a global warming potential (GWP) 23,000 times higher than Carbon Dioxide, and has the highest GWP of all gases assessed (Myhre 2013). SF 6 is almost exclusively man-made and is produced for use as an insulator in high voltage electrical equipment. This makes the production and use of SF 6 one of the leading sources of anthropogenic climate change. Since SF 6 recognition as a significant contributor to climate change, most governments and organizations have sought ways to reduce or eliminate their use of this gas. Many utilities have initiated leak monitoring and repair programs which have significantly reduced emissions of this gas into the atmosphere. While leak reduction programs have been effective at reducing emission rates in the developed world, leak rates remain frozen at ~1% annually. However, one of the largest and fastest growing markets for this gas is in the developing world where emissions standards are often lacking (P&S Intelligence. 2023). To fully eliminate the environmental impacts of SF 6 , alternative technology is needed. The ideal replacement would be a technology that can fulfil the same role as SF 6 , at the same cost or cheaper, but without adverse environmental effects. Currently, no technology fits this description, however several promising technologies have begun to enter the market. This report was commissioned by the United States Department of Energy’s Office of Electricity under the Transformer Resilience and Advanced Components (TRAC) program to assess the state of industry adoption and manufacturing capability for SF 6 -free alternative technologies for use at the high-voltage level, and the primary barriers to broader adoption. While this report is tailored to the United States, the findings should be relevant to all stakeholders seeking to reduce SF 6 emissions.

24 - POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

Enhancing predictive understanding and accuracy in geological carbon dioxide storage monitoring: Simulation and history matching of tracer transport dynamics

Co-injection of conservative tracers with carbon dioxide (CO 2 ) is a viable tool for monitoring subsurface processes during geological CO 2 storage (GCS). This research investigates the simulation and history-matching of a gas tracer (sulfur hexafluoride, SF 6 ) during CO 2 flooding, employing a core flooding result in Berea sandstone. Four extensively used saturation functions are assessed for their efficacy in history matching of CO 2 /SF 6 injection at the core scale. The history-matching process incorporates particle swarm optimization (PSO) to fine-tune constitutive relationships parameters. Next, employing transport models at the aquifer scale, we interrogate the impact on tracer transport and mixing of saturation function uncertainties, arising from the non-uniqueness of constitutive relationships parameters and saturation function types. To assess the effects of geological heterogeneity on behavior of tracer breakthrough curves (BTCs), we employ two normalized parameters assessing the degree of mixing and SF 6 breakthrough time. The aquifer-scale investigation encompasses both homogeneous and heterogeneous systems with and without capillary heterogeneity effects. Our findings underscore the critical importance of addressing saturation function uncertainties, emphasizing the significance of auxiliary experiments and innovative methodologies to enhance predictive accuracy. The findings highlight significant disparities in arrival times, BTC peaks, tails, and mixing levels, even under optimal conditions. Heterogeneity, with or without capillary heterogeneity, plays a crucial role in shaping BTC variations, resulting in accelerated SF 6 breakthrough times and reduced BTC peaks. Evaluation of monitoring points distant from the injector reveals a dampening effect on the SF6 BTC peak, particularly in heterogeneous systems with capillary heterogeneity, where the peak is halved. These insights underscore the challenges associated with tracer monitoring and the necessity for enhanced methodologies to improve predictive accuracy in subsurface processes during GCS.

58 GEOSCIENCES↗
DOE OSTI2022

Gas diffusion through variably-water-saturated zeolitic tuff: Implications for transport following a subsurface nuclear event

Noble gas transport through geologic media has important applications in the characterization of underground nuclear explosions (UNEs). Without accurate transport models, it is nearly impossible to distinguish between xenon signatures originating from civilian nuclear facilities and UNEs. Understanding xenon transport time through the earth is a key parameter for interpreting measured xenon isotopic ratios. One of the most challenging aspects of modeling gas transport time is accounting for the effect of variable water saturation of geological media. In this study, we utilize bench-scale laboratory experiments to characterize the diffusion of krypton, xenon, and sulfur hexafluoride (SF6) through intact zeolitic tuff under different saturations. Here, we demonstrate that the water in rock cores with low partial saturation dramatically affects xenon transport time compared to that of krypton and SF6 by blocking sites in zeolitic tuff that preferentially adsorb xenon. This leads to breakthrough trends that are strongly influenced by the degree of the rock saturation. Xenon is especially susceptible to this phenomenon, a finding that is crucial to incorporate in subsurface gas transport models used for nuclear event identification. We also find that the breakthrough of SF6 diverges significantly from that of noble gases within our system. When developing field scale models, it is important to understand how the behavior of xenon deviates from chemical tracers used in the field, such as SF6 (Carrigan et al., 1996). These new insights demonstrate the critical need to consider the interplay between rock saturation and fission product sorption during transport modeling, and the importance of evaluating specific interactions between geomedia and gases of interest, which may differ from geomedia interactions with chemical tracers.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2026

Experiments and simulations on the Richtmyer-Meshkov instability with a thin intermediate layer

Experiments and simulations of the Richtmyer-Meshkov instability (RMI) in two- and three-layer configurations are presented. The two-layer case utilizes a light-over-heavy configuration and consists of air as the light gas and sulfur hexafluoride (SF 6 ) as the heavy gas. The three-layer case utilizes a light-intermediate-heavy configuration, with helium (He) as the light gas, air as the intermediate gas, and SF 6 as the heavy gas. Statistically significant differences in the mixing layer width of the lower interface are not observed between the two cases. This differs from the experiments of Schalles et al., where a small, though statistically significant, difference in mixing layer growth was observed between the two- and three-layer cases with a nominally two-dimensional, single mode perturbation. Notably, the perturbations on the lower interface in the present work do not grow large enough to significantly interact with the upper interface during the duration of the experiments. In conclusion, this suggests that the differences in mixing layer growth observed by Schalles et al. may be due to interactions of the perturbations on one interface with the other interface rather than being inherent to the three-layer problem.

42 ENGINEERING↗
DOE OSTI2024

The influence of the shock-to-reshock time on the Richtmyer–Meshkov instability in reshock

Experiments on the Richtmyer–Meshkov instability (RMI) in a dual driver vertical shock tube (DDVST) are described. An initially planar, stably stratified membraneless interface is formed by flowing air from above and sulfur hexafluoride from below the interface location using the method of Jones & Jacobs ( Phys. Fluids , vol. 9, issue 1997, 1997, pp. 3078–3085). A random three-dimensional, multi-modal initial perturbation is imposed by vertically oscillating the gas column to produce Faraday waves. The DDVST design generates two shock waves, one originating above and one below the interface, with these shocks having independently controllable strengths and interface arrival times. The shock waves have nominal strengths of $M_L=1.17$ and $M_H=1.18$ for the shock wave originating in the light and heavy gas, respectively, with these strengths chosen to result in arrested bulk interface motion following reshock. The influence of the length of the shock-to-reshock time, as well as the order of shock arrival, on the post-reshock RMI is examined. The mixing layer width grows according to $h\propto t^\theta$ , where $\theta _H=0.36\pm 0.018$ (95 %) and $\theta _L=0.38\pm 0.02$ (95 %) for heavy and light shock first experiments, respectively, indicating no strong dependence on the order of shock wave arrival. Volume integrated specific turbulent kinetic energy (TKE) in the mixing layer versus time is found to decay according to $E_{tot}/\bar {\rho }\propto t^p$ with $p_H=-0.823\pm 0.06$ (95 %) and $p_L=-1.061\pm 0.032$ (95 %) for heavy and light shock first experiments, respectively. Notably, the 95 % confidence intervals do not overlap. Analysis on the influence of the shock-to-reshock time on turbulent length scales, transition criteria, spectra and mixing layer anisotropy are also presented.

Ferguson, Kevin (ORCID:0000000166537482)↗
DOE OSTI2020

Using SF 6 and Xe to Monitor Gas Migration Through Explosion-Generated Fracture Networks

Here we describe a field study where tracer gas was injected into a subsurface cavity created by a small chemical explosion beneath the water table. The main objective of the study is to compare the migration of sulfur hexafluoride (SF 6 ) and xenon (Xe) through an explosion-generated fracture network and to study the influence of ground water on gas transport. A mixture of tracer gases (50% of SF 6 and 50% of Xe) was injected on 31 October 2018 and gas sampling continued until 8 November 2018. We observe similar trends in SF 6 and Xe concentrations at four ground surface sampling sites. The changes in the SF 6 /Xe ratios with time show that more SF 6 than Xe is observed during the barometric pressure lows when the absolute measured concentrations are highest. Conversely, the ratio SF 6 /Xe is less than 1 during the high-pressure intervals when absolute measured concentrations are low. The results of the experiment suggest that during barometric pressure lows the tracer is migrating to the surface primarily by advective gas phase transport, whereas during barometric pressure highs, advection is suppressed and near-surface evaporation of interstitial pore fluid with tracer dissolved in it becomes more important. Thus, the results of the experiment show that the gas concentrations at the surface are controlled by the combined effects of the gas dissolution into pore water and the barometric pressure fluctuations.

58 GEOSCIENCES↗
DOE OSTI2021

Utilizing Environmental Tracers to Reduce Groundwater Flow and Transport Model Parameter Uncertainties

Abstract Non‐uniqueness in groundwater model calibration is a primary source of uncertainty in groundwater flow and transport predictions. In this study, we investigate the ability of environmental tracer information to constrain groundwater model parameters. We utilize a pilot point calibration procedure conditioned to subsets of observed data including: liquid pressures, tritium ( 3 H), chlorofluorocarbon‐12 (CFC‐12), and sulfur hexafluoride (SF 6 ) concentrations; and groundwater apparent ages inferred from these environmental tracers, to quantify uncertainties in the heterogeneous permeability fields and infiltration rates of a steady‐state 2‐D synthetic aquifer and a transient 3‐D model of a field site located near Riverton, Wyoming (USA). To identify the relative data worth of each observation data type, the post‐calibration uncertainties of the optimal parameters for a given observation subset are compared to that from the full observation data set. Our results suggest that the calibration‐constrained permeability field uncertainties are largest when liquid pressures are used as the sole calibration data set. We find significant reduction in permeability uncertainty and increased predictive accuracy when the environmental tracer concentrations, rather than apparent groundwater ages, are used as calibration targets in the synthetic model. Calibration of the Riverton field site model using environmental tracer concentrations directly produces infiltration rate estimates with the lowest uncertainties, however; permeability field uncertainties remain similar between the environmental tracer concentration and apparent groundwater age calibration scenarios. This work provides insight on the data worth of environmental tracer information to calibrate groundwater models and highlights potential benefits of directly assimilating environmental tracer concentrations into model parameter estimation procedures.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Real-space imaging of the electron-pair density hole in molecular Auger–Meitner decay

Electrons in matter can rearrange extremely quickly under external perturbations, underpinning subsequent structural and chemical transformations. Coulomb interactions between neighbouring electrons often shape this response, giving rise to correlated motion and strongly affecting the distribution of electrons in the system. Here we show that non-resonant hard X-ray scattering can directly access changes in the radial electron-pair density during the rapid rearrangement of core and valence electrons. We do this by studying sulfur hexafluoride molecules undergoing Auger–Meitner decay. We exploit a second-order interaction between the X-ray photons and the molecules to trigger and probe the decay dynamics with a single pulse, capturing the electron loss and redistribution before the molecules dissociate. The experiment shows that changes in electron-pair densities can be isolated and measured on ultrafast timescales, providing insight into the real-space evolution of highly excited and short-lived electronic states.

Simmermacher, Mats [University of Oxford (United K↗
DOE OSTI2026

The Use of Machine Learning Models for Predicting the Dielectric Strength of Gases

Technological advancements in high voltage systems have pushed sulfur hexafluoride (SF6) to its operational limits. Furthermore, this gas has other drawbacks including a high liquefaction temperature and a high global warming potential. Therefore, there has been an urgent need to find alternative gases with high dielectric strength (DS). In this work, density functional theory (DFT) is used to calculate molecular descriptors that are fed into an artificial neural network (ANN) and a random forest (RF). These machine learning (ML) models are then used to predict the DS for hundreds of molecules. A finite element model (FEM) is also used to calculate the electric field profile of multiple simple electrode geometries as the applied voltage to the system is increased. Results indicate that the random forest model has better generalization to unseen data than the neural network. The highest DS value predicted by the RF was 2.16 relative to the experimental DS of SF6. The results also demonstrate how choosing a gas with a higher DS and a geometry with minimal edges and corners can significantly increase the operating voltage of an electrical system. Due to its superior generalization, the RF represents the most promising path toward an accurate DS predictor once sufficient experimental data are available.

Mileski, Matthew [AFIT]↗
DOE OSTI2020

More chemical detection through less sampling: amplifying chemical signals in hyperspectral data cubes through compressive sensing

Compressive sensing (CS) is a method of sampling which permits some classes of signals to be reconstructed with high accuracy even when they were sampled at sub-Nyquist rates. In this paper we explore a phenomenon in which bandwise CS sampling of a hyperspectral data cube followed by reconstruction can actually result in amplification of chemical signals contained in the cube. Perhaps most surprisingly, chemical signal amplification generally seems to increase as the level of sampling decreases. In some examples, the chemical signal is significantly stronger in a data cube reconstructed from 10% CS sampling than it is in the raw, 100% sampled data cube. We explore this phenomenon in two real-world datasets including the Physical Sciences Inc. Fabry-Perot interferometer sensor multispectral dataset and the Johns Hopkins Applied Physics Lab FTIR-based longwave infrared sensor hyperspectral dataset. Each of these datasets contains the release of a chemical simulant, such as glacial acetic acid, triethyl phospate, and sulfur hexafluoride, and in all cases we use the adaptive coherence estimator (ACE) to detect a target signal in the hyperspectral data cube. We end the paper by suggesting some theoretical justifications for why chemical signals would be amplified in CS sampled and reconstructed hyperspectral data cubes and discuss some practical implications.

Hyperspectral imagery, Compressive Sensing, single↗
DOE OSTI2020

Materials Data on SF6 by Materials Project

SF6 crystallizes in the triclinic P-1 space group. The structure is zero-dimensional and consists of three sulfur hexafluoride molecules. S6+ is bonded in an octahedral geometry to six F1- atoms. All S–F bond lengths are 1.59 Å. There are two inequivalent F1- sites. In the first F1- site, F1- is bonded in a single-bond geometry to one S6+ atom. In the second F1- site, F1- is bonded in a single-bond geometry to one S6+ atom.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Materials Data on SF6 by Materials Project

SF6 is Tungsten structured and crystallizes in the cubic Im-3m space group. The structure is zero-dimensional and consists of two sulfur hexafluoride molecules. S6+ is bonded in an octahedral geometry to six equivalent F1- atoms. All S–F bond lengths are 1.60 Å. F1- is bonded in a single-bond geometry to one S6+ atom.

36 MATERIALS SCIENCE↗