Search NASA⌕ Search

SEARCH · Search NASA

Results for “TAIL MOUNTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Flight investigation of the effect of tail boom strakes on helicopter directional control

A joint U.S. Army/NASA flight investigation was conducted utilizing an instrumented Bell 240B single-rotor helicopter to determine the effectiveness of horizontally-mounted tail boom strakes on directional controllability and tail rotor power required during low-speed, crosswind operating conditions. The purpose of the strakes was to separate airflow over the tail boom and change fuselage yawing moments in a direction to improve the yaw control margin and reduce tail rotor power required. Low-speed crosswind data were obtained in 5-knot increments at airspeeds of 0 knots to 35 knots and for 30 deg increments in wind azimuth from 0 to 330 deg. In right sideward flight at the most critical wind azimuth and airspeed (60 deg azimuth measured from the nose of the aircraft and 20 knots airspeed), the strakes improved the pedal margin by about 6 percent of total travel and reduced the tail rotor power required by 17 percent. The increase in yaw control and reduction in tail rotor power offered by the strakes can expand the operating envelope in terms of gross weight and altitude capability. No effects in forward flight were noted.

Kelley, Henry L.↗

Development of Shared Mounting Structure for SUSAN Aircraft Tail and Aft Engine

This paper introduces an overview of the design and development of the Subsonic Single Aft eNgine (SUSAN) aircraft aft tail and engine shared mounting structure. Unique design considerations were made here to take advantage of aerodynamic effects such as boundary layer ingestion of the aft mounted engine. Challenges that arose from sharing the same mounting structure with the T-tail and aft engine were addressed. The structural development process will be discussed for both the initial design concept for the full-scale SUSAN aircraft concept, as well as the higher fidelity development of the 25% scale research vehicle. Numerical simulations for the aerodynamic loads are detailed and were fed into the 25% scale structural analysis effort. Additionally, mockup component fabrications of the shared aft engine and tail mounting structure are also shown to demonstrate design feasibility.

Lilia R Glaser↗

Theoretical aerodynamic characteristics of a family of slender wing-tail-body combinations

The aerodynamic characteristics of an airplane configuration composed of a swept-back, nearly constant chord wing and a triangular tail mounted on a cylindrical body are presented. The analysis is based on the assumption that the free-stream Mach number is near unity or that the configuration is slender. The calculations for the tail are made on the assumption that the vortex system trailing back from the wing is either a sheet lying entirely in the plane of the flat tail surface or has completely "rolled up" into two point vortices that lie either in, above, or below the plane of the tail surface.

Lomax, Harvard↗

Electrical emissions of airplanes flying in electrified clouds and their effect on airplane measurements of cloud electric fields

The signature of the cloud electric field components deduced from measurements made with electric field meters carried on airplane penetrating electrified clouds is often complex, especially when the airplane experiences strong electrical charging. However, simple electric field variations were obtained for penetrations involving severe charging of the airplane on flights over KSC on 19 Aug. 1989. During these episodes of severe electrical charging, the airplane typically became negatively charged as it approached a region of negative cloud charge and then became positively charged as it receded from the cloud charge. The charge acquired by the airplane within the cloud was so large that the electric fields at the faces of the mills mounted on the fuselage were as large as for an ambient electric field of 60 to 80 kV/m. However, the deduced electric field components perpendicular to the direction of flight, to which these mills respond, were only about 5 to 10 kV/m. The variation of the deduced ambient field component in the direction of flight was antisymmetric about the charge region for these penetrations. Analysis of these results suggest that intense plumes of electric charge were emitted from the airplane and that the electric field associated with these plumes overcame the electric field due to the cloud charge at the tail-mounted field mill. As a consequence, the deduced component of the ambient electric field in the direction of flight was severely distorted. These findings emphasize the need for careful evaluation of airplane electric field measurements and of the need for further work on techniques for improving the measurements.

Jones, James J.↗

A spin-recovery parachute system for light general-aviation airplanes

A tail mounted spin recovery parachute system was designed and developed by the NASA Langley Research Center for use on light general aviation airplanes. The system was designed for use on typical airplane configurations, including low wing, single engine, and twin-engine design. A mechanically triggered pyrotechnic slug gun is used to forcibly deploy a pilot parachute which extracts a bag that deploys a ring slot spin recovery parachute. The total system weighs 8.2 kg (18 lb). System design factors included airplane wake effects on parachute deployment, prevention of premature parachute deployment, positive parachute jettison, compact size, low weight, system reliability, and pilot and ground crew safety. Extensive ground tests were conducted to qualify the system. The recovery parachute was used successfully in flight 17 times.

Bradshaw, C.↗

A spin-recovery parachute system for light general-aviation airplanes

A tail mounted spin recovery parachute system was designed and developed for use on light general aviation airplanes. The system was designed for use on typical airplane configurations, including low wing, high wing, single engine and twin engine designs. A mechanically triggered pyrotechnic slug gun is used to forcibly deploy a pilot parachute which extracts a bag that deploys a ring slot spin recovery parachute. The total system weighs 8.2 kg. System design factors included airplane wake effects on parachute deployment, prevention of premature parachute deployment, positive parachute jettison, compact size, low weight, system reliability, and pilot and ground crew safety. Extensive ground tests were conducted to qualify the system. The recovery parachute was used successfully in flight 17 times.

Bradshaw, C.↗

A spin-recovery parachute system for light general aviation airplanes

A tail-mounted spin-recovery parachute system has been designed and developed by the NASA Langley Research Center for use on light general aviation airplanes. The system was designed for use on typical airplane configurations, including low-wing, high-wing, single- and twin-engine designs. A mechanically triggered pyrotechnic slug gun is used to forcibly deploy a pilot parachute which extracts a bag that deploys a ring-slot spin-recovery parachute. The total system weighs 8.2 kg (18 lb). System design factors included airplane wake effects on parachute deployment, prevention of premature parachute deployment, positive parachute jettison, compact size, low weight, system reliability, and pilot and ground crew safety. Extensive ground tests were conducted to qualify the system. The recovery parachute has been used successfully in flight 17 times.

Bradshaw, C. F.↗

Current perspectives on emergency spin-recovery systems

The requirements generated by the loss-of-control problems of contemporary and future aircraft are discussed in connection with the development of rocket and parachute technology for spin-recovery systems used in current aircraft. Recovery rockets must be designed to provide the thrust (not impulse) levels required by the specific application, because insufficient thrust will not effect a recovery regardless of its duration. The need for long firing times and a restart capability make liquid rocket systems preferable. Alternatives to the current tail-mounted method of implementing parachute systems include: nose chutes, wing-tip parachutes, dual-bridle and rigid towline systems. Comparative test results for these and the conventional system are given along with the latest dynamic model test technique for spin-recovery rockets.

Whipple, R. D.↗

Development and analysis of a STOL supersonic cruise fighter concept

The application of advanced and emerging technologies to a fighter aircraft concept is described. The twin-boom fighter (TBF-1) relies on a two dimensional vectoring/reversing nozzle to provide STOL performance while also achieving efficient long range supersonic cruise. A key feature is that the propulsion package is placed so that the nozzle hinge line is near the aircraft center-of-gravity to allow large vector angles and, thus, provide large values of direct lift while minimizing the moments to be trimmed. The configurations name is derived from the long twin booms extending aft of the engine to the twin vertical tails which have a single horizontal tail mounted atop and between them. Technologies utilized were an advanced engine (1985 state-of-the-art), superplastic formed/diffusion bonded titanium structure, advanced controls/avionics/displays, supersonic wing design, and conformal weapons carriage. The integration of advanced technologies into this concept indicate that large gains in takeoff and landing performance, maneuver, acceleration, supersonic cruise speed, and range can be acieved relative to current fighter concepts.

Dollyhigh, S. M.↗

Project Dawdler: a Proposal in Response to a Low Reynolds Number Station Keeping Mission

In direct response to Request for Proposals: Flight at very low Reynolds numbers - a station keeping mission, the members of Design Squad E present Project Dawdler: a remotely-piloted airplane supported by an independently controlled take-off cart. A brief introduction to Project Dawdler's overall mission and design, is given. The Dawdler is a remotely-piloted airplane designed to fly in an environmentally-controlled closed course at a Reynolds number of 10(exp 5) and at a cruise velocity of 25 ft/s. The two primary goals were to minimize the flight Reynolds number and to maximize the loiter time. With this in mind, the general design of the airplane was guided by the belief that a relatively light aircraft producing a fairly large amount of lift would be the best approach. For this reason the Dawdler utilizes a canard rather than a conventional tail for longitudinal control, primarily because the canard contributes a positive lift component. The Dawdler also has a single vertical tail mounted behind the wing for lateral stability, half of which is used as a rudder for yaw control. Due to the fact that the power required to take-off and climb to altitude is much greater than that required for cruise flight and simple turning maneuvers, it was decided that a take-off cart be used. Based on the current design, there are two unknowns which could possibly threaten the success of Project Dawdler. First, the effect of the fully-movable canard with its large appropriation of total lift on the performance of the plane, and secondly, the ability of the take-off procedure to go as planned are examined. These are questions which can only be answered by a prototype.

Bartilotti, Rich↗

A summary of spin-recovery parachute experience on light airplanes

From 1977 to 1989, the NASA Langley Research Center conducted stall/spin flight tests of variations of four typical light airplanes. Each was equipped with an identical tail-mounted, spin-recovery parachute system. The system was used 29 times to arrest otherwise unrecoverable spins and was used at least twice on each airplane. The 10.5 ft diameter, ring-slot, spin-recovery parachute with 20 ft attachment lines and drag coefficient of .545 provided recovery from spins at angles of attack of 32 to 79 degrees and rotation rates of 122 to 261 degrees per second in less than 3 1/2 turns.

Stough, H. Paul, III↗

Measured Engine Installation Effects of Four Civil Transport Airplanes

The Federal Aviation Administration's Integrated Noise Model (INM) is one of the primary tools for land use planning around airports. The INM currently calculates airplane noise lateral attenuation using the methods contained in the Society of Automotive Engineer's Aerospace Information Report No. 1751 (SAE AIR 1751). Researchers have noted that improved lateral attenuation algorithms may improve airplane noise prediction. The authors of SAE AIR 1751 based existing methods on empirical data collected from flight tests using 1960s-technology airplanes with tail-mounted engines. To determine whether the SAE AIR 1751 methods are applicable for predicting the engine installation component of lateral attenuation for airplanes with wing-mounted engines, the National Aeronautics and Space Administration (NASA) sponsored a series of flight tests during September 2000 at their Wallops Flight Facility. Four airplanes, a Boeing 767-400, a Douglas DC-9, a Dassault Falcon 2000, and a Beech KingAir, were flown through a 20 microphone array. The airplanes were flown through the array at various power settings, flap settings, and altitudes to simulate take-off and arrival configurations. This paper presents the preliminary findings of this study.

Senzig, David A.↗

Update on SUSAN Concept Vehicle Power and Propulsion System

This paper provides an update on the power and propulsion (P&P) system design for the SUbsonic Single Aft eNgine (SUSAN) Electrofan. The SUSAN vehicle concept is a transformative concept hybrid electric aircraft with a single tail-mounted turbofan engine that provides thrust and power to 16 electric propulsors located on the wings. This configuration makes uses of large-scale power extraction along with a high-power electrical system transmitting 20 MW of power from the engine to the wing propulsors. This paper goes into detail on P&P advances relating turbine engine design, electrical system capabilities, advanced turbine control techniques, and electrical system cooling techniques. It should be noted that the SUSAN concept continues to be developed and this paper simply offers an update on the design.

aircraft concept↗

Update on SUSAN Concept Vehicle Power and Propulsion System

This paper provides an update on the power and propulsion (P&P) system design for the SUbsonic Single Aft eNgine (SUSAN) Electrofan. The SUSAN vehicle concept is a transformative concept hybrid electric aircraft with a single tail-mounted turbofan engine that provides thrust and power to 16 electric propulsors located on the wings. This configuration makes uses of large-scale power extraction along with a high-power electrical system transmitting 20 MW of power from the engine to the wing propulsors. This paper goes into detail on P&P advances relating turbine engine design, electrical system capabilities, advanced turbine control techniques, and electrical system cooling techniques. It should be noted that the SUSAN concept continues to be developed and this paper simply offers an update on the design.

aircraft concept↗

Update on SUSAN Concept Vehicle Power and Propulsion System

This paper provides an update on the power and propulsion (P&P) system design for the SUbsonic Single Aft eNgine (SUSAN) Electrofan. The SUSAN vehicle concept is a transformative concept hybrid electric aircraft with a single tail-mounted turbofan engine that provides thrust and power to 16 electric propulsors located on the wings. This configuration makes uses of large-scale power extraction along with a high-power electrical system transmitting 20 MW of power from the engine to the wing propulsors. This paper goes into detail on P&P advances relating turbine engine design, electrical system capabilities, advanced turbine control techniques, and electrical system cooling techniques. It should be noted that the SUSAN concept continues to be developed and this paper simply offers an update on the design.

aircraft concept↗

Experimental aerodynamic characteristics of a generic hypersonic accelerator configuration at Mach numbers 1.5 and 2.0

An experimental investigation of the static longitudinal and lateral-directional aerodynamic characteristics of a generic hypersonic research vehicle was conducted in the Langley Unitary Plan Wind Tunnel (UPWT). A parametric study was performed to determine the interference effects of various model components. Configuration variables included delta and trapezoidal canards; large and small centerline-mounted vertical tails, along with a set of wing-mounted vertical tails; and a set of model noses with different degrees of bluntness. Wing position was varied by changing the longitudinal location and the incidence angle. The test Mach numbers were 1.5 and 2.0 at Reynolds numbers of 1 x 10(exp 6) per foot, 2 x 10(exp 6) per foot, and 4 x 10(exp 6) per foot. Angle of attack was varied from -4 degrees to 27 degrees, and sideslip angle was varied from -8 degrees to 8 degrees. Generally, the effect of Reynolds number did not deviate from conventional trends. The longitudinal stability and lift-curve slope decreased with increasing Mach number. As the wing was shifted rearward, the lift-curve slope decreased and the longitudinal stability increased. Also, the wing-mounted vertical tails resulted in a more longitudinally stable configuration. In general, the lift-drag ratio was not significantly affected by vertical-tail arrangement. The best lateral-directional stability was achieved with the large centerline-mounted tail, although the wing-mounted vertical tails exhibited the most favorable characteristics at the higher angles of attack.

Walker, Ira J.↗

A study to define the research and technology requirements for advanced turbo/propfan transport aircraft

The feasibility of the propfan relative to the turbofan is summarized, using the Douglas DC-9 Super 80 (DS-8000) as the actual operational base aircraft. The 155 passenger economy class aircraft (31,775 lb 14,413 kg payload), cruise Mach at 0.80 at 31,000 ft (8,450 m) initial altitude, and an operational capability in 1985 was considered. Three propfan arrangements, wing mounted, conventional horizontal tail aft mounted, and aft fuselage pylon mounted are selected for comparison with the DC-9 Super 80 P&WA JT8D-209 turbofan powered aircraft. The configuration feasibility, aerodynamics, propulsion, structural loads, structural dynamics, sonic fatigue, acoustics, weight maintainability, performance, rough order of magnitude economics, and airline coordination are examined. The effects of alternate cruise Mach number, mission stage lengths, and propfan design characteristics are considered. Recommendations for further study, ground testing, and flight testing are included.

Goldsmith, I. M.↗

Subsonic and supersonic aerodynamic characteristics of a supersonic cruise fighter model with a twisted and cambered wing with 74 deg sweep

A wind tunnel investigation has been conducted to determine the longitudinal and lateral aerodynamic characteristics of a model of a supersonic cruise fighter configuration with a design Mach number of 2.60. The configuration is characterized by a highly swept arrow wing twisted and cambered to minimize supersonic drag due to lift, twin wing mounted vertical tails, and an aft mounted integral underslung duel-engine pod. The investigation also included tests of the configuration with larger outboard vertical tails and with small nose strakes.

Morris, O. A.↗