Search NASA⌕ Search

SEARCH · Search NASA

Results for “TAIL SURFACES, VERTICAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Aerodynamic Characteristics of a Canard and an Outboard-Tail Airplane Model at High Subsonic Speeds

An investigation has been made in the Langley high-speed 7- by 10-foot tunnel through a range of Mach numbers from 0.60 to 0.95 of the static longitudinal and lateral stability and control characteristics of a canard airplane configuration and an outboard-tail configuration. The canard model had a twisted wing with approximately 67 deg of sweepback and an aspect ratio of 2.91 and was tested with three trapezoidal canard surfaces having ratios of exposed area to wing area of 0.032, 0.076, and 0.121. The canard model had a single body-mounted vertical tail. The outboard-tail model had its horizontal- and vertical-tail surfaces mounted on slender bodies attached to the wing tips and located to the rear and outboard of the 67 deg sweptback wing of aspect ratio 1.00. The data, which are presented with limited analysis, provide information at high subsonic speeds on these two types of high-speed airplanes which have previously been tested at supersonic speeds and reported in NACA RM L58BO7 and NACA RM L58E20.

Fournier, Paul G.↗
NASA NTRS1945

Determination of the Stability and Control Characteristics of a Tailless All-Wing Airplane Model with Sweepback in the Langley Free-Flight Tunnel

Force and flight tests were performance on an all-wing model with windmilling propellers. Tests were conducted with deflected and retracted flaps, with and without auxiliary vertical tail surfaces, and with different centers of gravity and trim coefficients. Results indicate serious reduction of stick-fixed longitudinal stability because of wing-tip stalling at high lift coefficient. Directional stability without vertical tail is undesirably low. Low effective dihedral should be maintained. Elevator and rudder control system is satisfactory.

WING FLAPS - DEFLECTION↗
NASA NTRS1973

Multistage aerospace craft

A conceptual design of a multi-stage aerospace craft is presented. Two perspective views of the vehicle are developed to show the two component configuration with delta wing, four vertical tail surfaces, tricycle landing gear, and two rocket exhaust nozzles at the rear of the fuselage. Engines for propulsion in the atmosphere are mounted on the fuselage in front of the wing root attachment.

Kelly, D. L.↗
NASA NTRS1976

Spin tests of a 1/20-scale model of the XF4U-1 airplane, 12 July 1939

These tests were performed to determine the spinning characteristics of the 1/20-scale model of the XF4U-1 airplane. Effects of loading changes and various control dispositions using both the original and modified vertical tail surfaces were studied. Subsequent tests were made to determine the effects of additional tail modifications.

Donlan, C. J.↗
NASA NTRS1987

On the nonlinear aerodynamic and stability characteristics of a generic chine-forebody slender-wing fighter configuration

An exploratory investigation was conducted of the nonlinear aerodynamic and stability characteristics of a tailless generic fighter configuration featuring a chine-shaped forebody coupled to a slender cropped delta wing in the NASA Langley Research Center's 12-Foot Low-Speed Wind Tunnel. Forebody and wing vortex flow mechanisms were identified through off-body flow visualizations to explain the trends in the longitudinal and lateral-directional characteristics at extreme attitudes (angles of attack and sideslip). The interactions of the vortical motions with centerline and wing-mounted vertical tail surfaces were studied and the flow phenomena were correlated with the configuration forces and moments. Single degree of freedom, free-to-roll tests were used to study the wing rock susceptibility of the generic fighter model. Modifications to the nose region of the chine forebody were examined and fluid mechanisms were established to account for their ineffectiveness in modulating the highly interactive forebody and wing vortex systems.

Erickson, Gary E.↗
NASA NTRS1987

On the nonlinear aerodynamic and stability characteristics of a generic chine-forebody slender-wing fighter configuration

An exploratory investigation was conducted of the nonlinear aerodynamic and stability characteristics of a tailless generic fighter configuration featuring a chine-shaped forebody coupled to a slender cropped delta wing in the NASA Langley Research Center's 12-Foot Low-Speed Wind Tunnel. Forebody and wing vortex flow mechanisms were identified through off-body flow visualizations to explain the trends in the longitudinal and lateral-directional characteristics at extreme attitudes (angles of attack and sideslip). The interactins of the vortical motions with centerline and wing-mounted vertical tail surfaces were studied and the flow phenomena were correlated with the configuration forces and moments. Single degree-of-freedom, free-to-roll tests were used to study the wing rock susceptibility of the generic fighter model. Modifications to the nose region of the chine forebody were examined and fluid mechanisms were established to account for their ineffectiveness in modulating the highly interactive forebody and wing vortex systems.

Erickson, Gary E.↗
NASA NTRS1990

Development and implementation of a shuttle modal inspection system

One of the major tasks between Space Shuttle flights is inspection of the orbiter subsystems such as control surfaces, vertical tail, and wings. To date, inspection techniques have consisted primarily of visual and X-ray methods, which are not only time consuming but not as comprehensive as desired. Previous shuttle component and orbiter ground modal testing revealed that orbiter component damage could be identified using standard modal test methods. As a result, NASA has procured a dedicated shuttle modal inspection system (SMIS) that will be used for subsystem inspection. This paper presents a background on the use of modal testing to detect shuttle component damage, details on this new implementation, and an early use of the SMIS capability to investigate a potential orbiter vibration problem.

Hunt, David L.↗
NASA NTRS1939

Pressure-distribution investigation of an N.A.C.A. 0009 airfoil with a 50-percent-chord plain flap and three tabs

Pressure-distribution tests of an N.A.C.A. 0009 airfoil with a 50-percent-chord plain flap and three plain tabs, having chords 10, 20, and 30 percent of the flap chord, were made in the N.A.C.A. 4- by 6- foot vertical tunnel. The tests supplied aerodynamic section data that may be applied to the design of horizontal and vertical tail surfaces. The results are presented as resultant-pressure diagrams for the airfoil with the flap and the 20-percent-chord tab. Plots are also given of increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs. The experimental results and values computed by analytical methods are in good agreement for small flap and tab deflections. The results of the tests indicated that the effectiveness of all three tab sizes in reducing flap hinge moments decreased with increasing flap deflection.

Street, William G↗
NASA NTRS1940

Pressure-distribution investigation on an NACA 0009 airfoil with a 30-percent-chord plain flap and three tabs

Pressure-distribution tests of an NACA 0009 airfoil with a 30-percent-chord plain flap and three plain tabs, having chords 10, 20, and 30 percent of the flap chord, were made. The purpose of these tests was to continue an investigation to supply structural and aerodynamic section data that may be applied to the design of horizontal and vertical tail surfaces. The results are presented as diagrams of resultant pressures and of resultant-pressure increments for the airfoil with the flap and the 20-percent-chord tab. Increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs are also given. At all unstalled flap and tab deflections, the experimental distributions agree well with those calculated by an analytical method. The agreement is poor, however, then the stalled or the unstalled condition of the flap or tab deflected alone was changed to an unstalled or stalled condition by the simultaneous deflection of both the flap and the tab.

Ames, Milton B↗
NASA NTRS1940

Pressure-distribution investigation of an NACA 0009 airfoil with an 80-percent-chord plain flap and three tabs

Pressure-distribution tests of an NACA 0009 airfoil with an 80-percent-chord plain flap and three plain tabs, having chord of 10, 20, and 30 percent of the flap chord, were made. Section data suitable for application to the design of horizontal and vertical tail surfaces were obtained. Resultant-pressure diagrams for the airfoil with the flap and the 20-percent-chord tab are presented. Plots are also given of increments of normal-force and hinge-moment coefficients for the airfoil, the flap, and the three tabs. A comparison of some characteristic slopes for the 30-, the 50-, and the 80-percent-chord flaps, tested in the general investigation of plain flaps for control surfaces, is included. Section aerodynamic and load data have been made available for a wide range of flap and a tab chords to be used on an NACA 0009 airfoil or on other conventional sections.

Ames, Milton B , Jr↗
NASA NTRS1923

Pressure Distribution over the Rudder and Fin of an Airplane in Flight

This investigation was carried out by the National Advisory Committee for Aeronautics at the Langley Memorial Aeronautical Laboratory for the purpose of determining the loads which occur on the vertical tail surfaces in flight. The method consisted in measuring the pressures simultaneously at 28 points on the rudder and fin by means of a recording multiple manometer. The results show that the maximum load encountered in stunting was 7 pounds per square foot on the rudder and fin, and it is probable that this might rise to 10 pounds per square foot in a violent barrel roll; but in steady flight the average loads do not exceed 0.6 pound per square foot. The maximum load on the rudder and fin may occur at the same instant as the maximum load on the horizontal tail surfaces and the maximum normal acceleration. The torsional moment about the axis of the fuselage due to the rudder and fin may rise as high as 250 foot-pound. The results obtained from this investigation have a direct application to the design of the rudder, fin, and fuselage.

Norton, F H↗
NASA NTRS1934

The calculation of lateral stability with free controls

The discussion of the structural methods for obtaining lateral stability discloses the remarkable influence of the constant fuselage and wing proportions to the yawing moments. For the effectiveness of modifications in vertical tail surfaces and tail length, these quotas - little observed heretofore, in this connection - are decisive. This also applies to the amount of dihedral of the wing with regard to the roll stability of the complete wing already existing without angle of the dihedral.

Mathias, Gotthold↗
NASA NTRS1993

The airplane: A simulated commercial air transportation study

The 'Airplane' is a moderate-range, 70 passenger aircraft. It is designed to serve demands for flights up to 10,000 feet and it cruises at 32 ft/s. The major drivers for the design of the Airplane are economic competitiveness, takeoff performance, and weight minimization. The Airplane is propelled by a single Astro 15 electric motor and a Zinger 12-8 propeller. The wing section is a Spica airfoil which, because of its flat bottom, provides simplicity in manufacturing and thus helps to cut costs. The wing is constructed of a single load bearing mainspar and shape-holding ribs coated with Monokote skin, lending to a light weight structural makeup. The fuselage houses the motor, flight deck and passenger compartments as well as the fuel and control actuating systems. The wing will be attached to the top of the fuselage as will the fuel and control actuator systems for easy disassembly and maintenance. The aircraft is maneuvered about its pitch axis by means of an aft elevator on the flat plate horizontal tail. The twin vertical tail surfaces are also flat plates and each features a rudder for both directional and roll control. Along with wing dihedral, the rudders will be used to roll the aircraft. The Airplane is less costly to operate at its own maximum range and capacity as well as at its maximum range and the HB-40's maximum capacity than the HB-40.

Dauteuil, Mark↗
NASA NTRS1999

Ice Accretion Calculations for a Commercial Transport Using the LEWICE3D, ICEGRID3D and CMARC Programs

Collection efficiency and ice accretion calculations were made for a commercial transport using the NASA Lewis LEWICE3D ice accretion code, the ICEGRID3D grid code and the CMARC panel code. All of the calculations were made on a Windows 95 based personal computer. The ice accretion calculations were made for the nose, wing, horizontal tail and vertical tail surfaces. Ice shapes typifying those of a 30 minute hold were generated. Collection efficiencies were also generated for the entire aircraft using the newly developed unstructured collection efficiency method. The calculations highlight the flexibility and cost effectiveness of the LEWICE3D, ICEGRID3D, CMARC combination.

Bidwell, Colin S.↗
NASA NTRS2007

Wind Tunnel Investigation of the Effects of Surface Porosity and Vertical Tail Placement on Slender Wing Vortex Flow Aerodynamics at Supersonic Speeds

A wind tunnel experiment was conducted in the NASA Langley Research Center (LaRC) Unitary Plan Wind Tunnel (UPWT) to determine the effects of passive surface porosity and vertical tail placement on vortex flow development and interactions about a general research fighter configuration at supersonic speeds. Optical flow measurement and flow visualization techniques were used that featured pressure sensitive paint (PSP), laser vapor screen (LVS), and schlieren, These techniques were combined with conventional electronically-scanned pressure (ESP) and six-component force and moment measurements to quantify and to visualize the effects of flow-through porosity applied to a wing leading edge extension (LEX) and the placement of centerline and twin vertical tails on the vortex-dominated flow field of a 65 cropped delta wing model. Test results were obtained at free-stream Mach numbers of 1.6, 1.8, and 2.1 and a Reynolds number per foot of 2.0 million. LEX porosity promoted a wing vortex-dominated flow field as a result of a diffusion and weakening of the LEX vortex. The redistribution of the vortex-induced suction pressures contributed to large nose-down pitching moment increments but did not significantly affect the vortex-induced lift. The trends associated with LEX porosity were unaffected by vertical tail placement. The centerline tail configuration generally provided more stable rolling moments and yawing moments compared to the twin wing-mounted vertical tails. The strength of a complex system of shock waves between the twin tails was reduced by LEX porosity.

Erickson, Gary E.↗