Results for “TAP reactor” — Page 2

DOE OSTI2026

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2025

Binder jet additive manufacturing of silicon carbide solar reactor

Achieving high powder packing density is critical in binder jet additive manufacturing (BJAM), as it directly influences the final part density, mechanical properties, and sintering behavior. Multi-modal powder blends, which combine particles of different sizes, have been explored as a strategy to optimize packing efficiency and minimize defects. In this study, bimodal and trimodal powder blends were obtained by mixing silicon carbide powder in three different sizes. These results show that increased powder density is achievable with bimodal powder blends but is reduced in trimodal blends, and it was found that a 13% increase in the powder tap density was achieved using a bimodal blend of powder. The powder size distribution of the bimodal blend was measured at various stages during binder jet additive manufacturing and, no measurable powder separation occurred even after eight prints. Overall, this study shows limited advantage to trimodal powder blends but good promise for trimodal blends for increasing printed density while maintaining reusability in the binder jet process.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Binder Jet Additive Manufacturing of Silicon Carbide Solar Reactor (CRADA Report)

Achieving high powder packing density is critical in binder jet additive manufacturing (BJAM), as it directly influences the final part density, mechanical properties, and sintering behavior. Multi-modal powder blends, which combine particles of different sizes, have been explored as a strategy to optimize packing efficiency and minimize defects. In this study, bimodal and trimodal powder blends were obtained by mixing silicon carbide powder in three different sizes. These results show that increased powder density is achievable with bimodal powder blends but is reduced in trimodal blends, and it was found that a 13% increase in the powder tap density was achieved using a bimodal blend of powder. The powder size distribution of the bimodal blend was measured at various stages during binder jet additive manufacturing and, no measurable powder separation occurred even after eight prints. Overall, this study shows limited advantage to trimodal powder blends but good promise for trimodal blends for increasing printed density while maintaining reusability in the binder jet process.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2026

SPC-70791 Rev 0 MARVEL Inert Gas Subsystem, Secondary Coolant Management Subsystem, and Secondary Coolant Cover Gas Subsystem Tubing and Valve Specification

This specification covers the requirements and details for the selection, testing, cleaning, marking, shipping, inspection and installation (including welding) of the Inert Gas Subsystem, Secondary Coolant Management Subsystem, and Secondary Cover Gas Management Subsystem from the Valve Panel up to the classification division, the patch panel of the upper confinement. Including NaK, argon, eutectic gallium indium tin (eGaInSn), and helium fill tubing, valves, and hangers. These systems consist of the necessary straight lengths, elbows, reducers, fittings, tube connections, instrument taps, and valves called for by applicable drawings. All components shall be procured as ASME Section III Class 2 unless otherwise modified hereinafter. Pressure relief valves have been sized to prevent overpressure in the event there is full regulator flow. This is documented in ECAR-7365.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗