Search NASA⌕ Search

SEARCH · Search NASA

Results for “TEM and SEM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Direct ink writing of shear exfoliated two-dimensional nanomaterial- elastomeric multifunctional nanocomposite

Direct ink writing (DIW) of polymer nanocomposites with high loadings of two-dimensional (2D) nanofillers (graphene and hexagonal boron nitride (hBN)) is challenging because of potential clogging, use of hazardous solvents, and agglomeration. Here, in this work, a shear exfoliation and sieving method to prepare DIW ink with high loading of nanofillers produced from low-cost bulk layered materials such as graphite and bulk hBN powder for successful DIW printing without the use of any solvents, binders, or plasticizers. The single-step exfoliation technique resulted in a composite with substantial layer reduction along the c-axis, as confirmed by SEM, TEM, XRD, and Raman analysis. Incorporating exfoliated graphene (40 wt%) increased viscosity by ∼6 orders of magnitude due to enhanced particle–matrix interactions, leading to pronounced yield stress behavior and a yield stress of approximately 1598 Pa, which enabled excellent shape retention during extrusion. Using the DIW technique, porous structures such as desalination membranes, self-sensing bone scaffolds, thermal management coating, and serpentine strain sensors were fabricated. When tested in a direct contact membrane distillation setup, the fabricated membrane demonstrated a promising permeate flux of 21.85 Lm −2 h −1 and a salt rejection of 74.3 %. The fabricated serpentine sensor exhibited stable signal variations under cyclic tensile loading, with a working range of 0–200 % strain and a maximum gauge factor of 43,735. A cell culture test using the printed bone scaffold demonstrated promising cell attachment and proliferation. The DIW printed hBN nanocomposite exhibited reversible shape change under heat, demonstrating potential 4D printing capability and efficient thermal management when exposed to high heat or flame.

Desalination↗
DOE OSTI2022

Removal and recovery of ammonia from simulated wastewater using Ti3C2Tx MXene in flow electrode capacitive deionization

Abstract Flowing electrode capacitive deionization systems (FE-CDI) have recently garnered attention because of their ability to prevent cross contamination and operate in uninterrupted cycles ad infinitum. Typically, FE-CDI electrodes suffer from low conductivity, reducing deionization performance. Utilization of higher mass loadings to combat this leads to poor rheological properties. Herein, Ti 3 C 2 T x MXene was introduced as 1 mg mL −1 slurry electrodes in an FE-CDI system for the removal and recovery of ammonia from simulated agricultural wastewater. The electrode performance was evaluated by operating the FE-CDI system with a feed solution of 500 mg L −1 NH 4 Cl running in batch mode at a constant voltage of 1.20 and −1.20 V in charging and discharging modes, respectively. Despite the low loading, Ti 3 C 2 T x flowing electrodes showed markedly improved performance, achieving 60% ion removal efficiency in a saturation time of 115 min with an adsorption capacity of 460 mg g −1 . To understand the high adsorption performance of the electrodes, physiochemical and structural analysis was done via a variety of characterization techniques such as SEM, TEM, XRD, DLS, and Raman spectroscopy. Cyclic voltammetry and galvanostatic charge/discharge profiles were obtained to evaluate the electrochemical properties of the electrodes. The system proved to be an energy-saving technology by exhibiting a charge efficiency of 58–70% while operating at an energy consumption of 0.45 kWh kg −1 . A 92% regeneration efficiency showed that the electrodes were stable and suitable for long term and scalable usage. The results demonstrate that MXenes have the potential to improve the FE-CDI process for energy-efficient removal and recovery of ammonia.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Use of imaging and mass spectrometry-based capabilities to describe microbiome interactions (Q4 Performance Metric Report, 2021)

The LLNL “Microbes Persist” Soil Microbiome Scientific Focus Area (SFA) seeks to determine how microbial soil ecophysiology, population dynamics, and microbe-mineral-organic matter interactions regulate the persistence of microbial residues and formation of soil carbon (C). In much of our research, we use imaging, mass spectrometry, and related methods to study plantmicrobe-mineral interactions, viral and microbial particles from soil, and the signatures plant and microbial necromass contribute as part of soil organic matter (SOM). Our project’s signature techniques include NanoSIMS-enabled approaches (to understand cell-cell and OM-mineral interactions at the single cell and even viral particle scale), radiocarbon (14C) analyses (to determine both the age and turnover time of soil organic matter), and a suite of soil chemical characterization techniques we describe below, and collectively refer to as ‘Multi- dimensional SOM-mineral characterization’ (SEM, TEM, STXM, NEXAFS, NMR, FTICR-MS, LC-MS). In this report, we focus on how imaging, NMR, beamline and mass spectrometry approaches can deepen our understanding of soil microbiomes and their engagement with the soil matrix.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Characterization of Multi-Material Interfaces Within Fibrous Structures (CRADA Final Report)

This project aimed to characterize the electrical, ionic, and thermal material properties of printed materials onto various textile and leather substrates. Furthermore, the material interfaces were investigated as well via characterization techniques such as SEM, TEM, and FTIR for example. Results from these studies will be utilized to properly formulate and tune process variables for enhancing the durability of devices and mitigate risks during commercial scale manufacturing studies of interest to Funxion’s product development.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Exploring the Impact of N Solubility and Trace Elements on the Creep Properties of P92 Steel

Trace elements can have major consequences on the properties of creep resistant martensitic steels. To better understand the changes in microstructure and mechanical performance associated with the variation of trace elements and enable design of steels operating at more demanding conditions, we formulated three versions of P92 within the specified allowable N, B, C and Si ranges. Different service conditions were explored, and >80% decrease in creep life was observed at 625°C 155MPa for the highest B and N containing alloy. Multiscale characterization (OM, SEM, TEM) revealed key changes due to the trace element variation. The high trace content alloy formed deleterious BN precipitates with morphology that would promote crack nucleation, but also formed higher fractions of beneficial MX precipitates. The alloy with the lowest trace content showed the best creep performance – a result of the refined precipitate populations and the absence of large-scale inclusions and BN precipitates.

Antonov, Stoichko↗
DOE OSTI2020

Generalized synthesis of high surface area mesoporous metal titanates as efficient heterogeneous catalysts

A novel metal dissolution coupled with reverse micelle formation approach is used as a generalized synthesis method for a series of high surface area metal titanates where the metals used are Bi, Mg, V, Mn, Fe, Co, Ni, Cu, Zn, Mo, W, and Ce. This study reports the highest surface areas published so far. The homogeneous distributions of the metals and titanium are observed in SEM-EDX and TEM mapping. The synthesized materials were comprehensively characterized using PXRD, Raman, nitrogen adsorption isotherms, SEM; EDX, TEM, TEM mapping, TGA, and XPS. The green catalytic oxidation of aniline to nitrosobenzene occurs within 30 min at room temperature when mesoporous W/Ti binary metal oxide is used as the catalyst. The radical mediated catalytic reaction gives excellent yields and the catalyst is reusable up to 4 reaction cycles without losing significant activity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

NanoSIP: NanoSIMS Applications for Microbial Biology

High-resolution imaging with secondary ion mass spectrometry (nanoSIMS) has become a standard method in systems biology and environmental biogeochemistry and is broadly used to decipher ecophysiological traits of environmental microorganisms, metabolic processes in plant and animal tissues, and cross-kingdom symbioses. When combined with stable isotope-labeling—an approach we refer to as nanoSIP—nanoSIMS imaging offers a distinctive means to quantify net assimilation rates and stoichiometry of individual cell-sized particles in both low- and high-complexity environments. While the majority of nanoSIP studies in environmental and microbial biology have focused on nitrogen and carbon metabolism (using 15 N and 13 C tracers), multiple advances have pushed the capabilities of this approach in the past decade. The development of a high-brightness oxygen ion source has enabled high-resolution metal analyses that are easier to perform, allowing quantification of metal distribution in cells and environmental particles. New preparation methods, tools for automated data extraction from large data sets, and analytical approaches that push the limits of sensitivity and spatial resolution have allowed for more robust characterization of populations ranging from marine archaea to fungi and viruses. Further, NanoSIMS studies continue to be enhanced by correlation with orthogonal imaging and ‘omics approaches; when linked to molecular visualization methods, such as in situ hybridization and antibody labeling, these techniques enable in situ function to be linked to microbial identity and gene expression. Here we present an updated description of the primary materials, methods, and calculations used for nanoSIP, with an emphasis on recent advances in nanoSIMS applications, key methodological steps, and potential pitfalls.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2025

Exploring microstructures and anisotropies of serpentinites

Serpentine minerals have received a lot of attention because of their unique crystal structures, their wide occurrence in orogenic belts and their potential role in contributing seismic anisotropy in subducting slabs. Several studies have investigated crystal preferred orientation (CPO) in high temperature antigorite serpentinites from Japan, the Alps, Spain, Cuba and Tibet, documenting significant crystal alignment. However, only a limited number of lower grade serpentines have been explored to date. Mainly because of submicroscopic microstructural heterogeneities CPO cannot be measured with conventional methods such as optical microscopy and EBSD. In this study 15 serpentinites from different tectonic settings in California, the Central Alps and Northern Spain have been investigated, mainly with high energy synchrotron X-ray diffraction, to quantify bulk crystal alignment. We find that CPO is strong on sheared surfaces of fractured blocks and secondary veins but the bulk of most serpentinite samples, except high-grade recrystallized antigorite serpentinite, show only weak crystal alignment. Correspondingly calculated seismic anisotropy based on CPO is not very significant. This is supported by very heterogeneous microstructures as documented with SEM and TEM analyses.

58 GEOSCIENCES↗
DOE OSTI2025

Welding investigation of a wrought FeMnAl steel for armor application

A new wrought FeMnAl steel contains high Mn content and high Al content. This steel has high strength. When it is compared to conventional steels with the similar strength, its density is lower. FeMnAl steels can be used in armor vehicle manufacturing, in which welding is a common practice to join the steel plates together. The welding of FeMnAl steels has not been sufficiently studied before. Here, this work studied the weldability and weld microstructure of an FeMnAl steel and provided useful data for the welding practice of FeMnAl steels. The influences of weld filler metals and shielding gases were studied, using single-pass bead-on-plate gas metal arc welding (GMAW) and gas tungsten arc welding (GTAW) two processes. The optimal filler metals and shielding gases have been determined to achieve the better weldability. Autogenous GTAW and electron beam welding were also conducted. Cracks were found in the HAZ in the GMAW welds and electron beam welds. Fewer or no cracks were found in the HAZ of GTAW welds. SEM, SEM/EDX, TEM, TEM/EDX, and EBSD were used to analyze the grain boundaries in the HAZ and the cracks. The grain boundaries of FeMnAl base metal are mostly high angle grain boundaries (HAGBs), which attract impurity and solute atoms and cause intergranular cracking. The proposed cracking mechanisms are liquation cracking and ductility-dip cracking. It was found that GTAW provides much better weldability for the FeMnAl steel than GMAW and EBW.

FeMnAl steel↗
DOE OSTI2020

Grid-assisted magnetron sputtering deposition of nitrogen graded TiN thin films

Titanium Nitride (TiN) films were obtained using the grid-assisted magnetron sputtering deposition technique on Al substrates in two conditions: under constant and variable nitrogen concentration along the thin solid film thickness. The formation of a film with variable N concentration (herein referred as graded film) was confirmed using energy filtered transmission electron microscopy, X-ray photoelectron spectroscopy and grazing incidence X-ray diffraction. The TiN thin films microstructures were also analysed using scanning and transmission electron microscopies (SEM and TEM). Finally, the viability of synthesizing TiN thin films with variable N concentration is herein proposed as an alternative method for tailoring the properties of such functional coating materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Grafted nickel-promoter catalysts for dry reforming of methane identified through high-throughput experimentation

High-throughput synthesis of a series of monometallic and bimetallic catalysts (45 bimetallic and 50 monometallic samples) consisting of nickel and one of nine different metal promoters (B, Co, Cu, Fe, Mg, Mn, Sn, V and Zn) supported on one of six different metal oxides alumina, ceria, magnesia, silica and titania) is carried out via organometallic grafting using a robotic platform. The catalysts are evaluated for their activity and selectivity for the dry reforming of methane at a feed ratio of CH 4 :CO 2 of 1 at 650–800 °C in a parallel flow reactor system. The type of oxide support prevails over the type of additive for both catalyst activity and stability. On Al 2 O 3 and MgO, Fe was found to be the best promoter; on SiO 2 , Cu is the best promoter at 700 °C and higher, while on TiO 2 , Mn is found to enhance the conversion at 800 °C. On CeO 2 , all additives except Fe have beneficial effects. Twenty-five catalysts show > 90% methane conversion with ten catalysts showing > 95% conversion at 800 °C with the H 2 :CO ratios ranging from 0.8 to 1.2. Amongst the ten highest performers, NiFe/Al 2 O 3 and NiFe/MgO are more active than Ni/Al 2 O 3 and Ni/MgO, respectively and were stable over a period of 25 h at 800 °C. Characterization on the as-prepared samples reveals highly dispersed phase, while after reduction in H 2 , highly dispersed and reduced nickel particles up to 10 nm are formed. The particles do not increase in size under dry reforming reaction conditions at 800 °C. An increased hydrogen consumption observed during H 2 -TPR of the nickel particles is positively correlated with methane conversion for Al 2 O 3 -based catalysts. The resistance to deactivation by coking and variation in coke structure are investigated by spectroscopic and microscopic methods to identify the relationship between metal promoters, alloy formation, and type of surface carbon deposits. Carbon whiskers were observed on the ten selected spent samples and are preferentially deposited on Ni rather than on the promoters. Carbon nanotube formation and metal particle removal from support were not observed to cause deactivation while amorphous carbon formation was clearly linked to catalyst deactivation, as amorphous carbon could encapsulate nickel, either on the support or at the end of the carbon nanotube. Furthermore, the organometallic grafting technique is an efficient and suitable technique for synthesizing highly dispersed and homogeneous phases which lead to high conversion and high durability for dry reforming of methane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Structural and magnetic properties of hard magnetic system Ce(Co 1 -Fe ) 4.4 Cu 0.6 (0 ≤ x ≤ 0.19)

The Ce(Co 1 -Fe ) 4.4 Cu 0.6 (0 ≤ x ≤ 0.19) is a composite, hard magnetic system that is based on the CaCu 5 -type structure (1:5). It shows both, unique magnetic and microstructural features that are essential for permanent magnets, e.g., exceptional squareness of the 2nd. quadrant of the magnetization loops and microstructural features typically needed for pinning. Samples solidified in alumina crucibles are coarse-grained and often clearly faceted and readily align in a magnetic field. X-ray, SEM, and TEM analyses show a 1:5-type single-phase material when quenched from high temperature, which, after heat treatment, transforms into a laminar coherent nanostructure through the formation of a dense array of extended intercalated regions. Furthermore, these extended intercalated regions are comprised of segments of the Ce 2 Ni 7 –type structure (2:7) which segregate into various closely related precipitates forming a nanostructure similar to the SmCo 5 - Sm 2 Co 17 composites seen in Sm-Co permanent magnets. Based on TEM and Lorentz microscopy of well-aligned single grain particles, the magnetic domains’ reversal mechanism is regulated by anisotropy fluctuations occurring along the easy direction of magnetization and strong exchange interactions between the matrix and defects (e.g.: stacking faults). Lorentz microscopy suggests the domain wall is not physically pinned by the defect, but rather is offset/deflected when it interacts with the defect. The Lorentz and magnetization data suggest that defects cause a bending of the moment away from the c axis inside the grains.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Hardenability and microstructural evolution of a precipitation strengthened Ni 50 Ti 21 Hf 25 Al 4 alloy

NiTi-based quaternary alloys are used in a variety of mechanical components, such as bearings, actuators, and dampers, owing to their good hardenability, wear resistance, and corrosion resistance. Additionally, one of the most notable characteristics of NiTi-based alloys is their shape memory effect and pseudoelastic properties. Connecting the macroscopic processing parameters employed in the design of new intermetallic alloys to the nanoscale structural characteristics dictating their behavior is crucial for improving their mechanical properties and expanding the spectrum of potential applications. Here, in this work, an arc melted Ni 50 Ti 21 Hf 25 Al 4 (at%) alloy was solution treated at 1050 °C followed by quenching and aging at 600 °C to investigate the effect of aging time on the microstructure and mechanical properties. Two types of nano-sized precipitates were observed and determined as face-centered orthorhombic H-phase (TiHf)Ni and L2 1 Heusler precipitates Ni 2 TiAl. The morphology and orientation of the H-phase were investigated using scanning and transmission electron microscopy (SEM and TEM), elucidating the coarsening kinetics and strengthening contribution of that phase to the intermetallic mechanical behavior. Following coarsening, the presence of Heusler nanoprecipitates was detected under overaged conditions through TEM imaging and nanobeam electron diffraction patterns. A peak hardness condition of 756 HV was achieved after 70 h of aging, indicating that the co-precipitation of H-phase and Heusler precipitates through a well-designed aging treatment can lead to optimal mechanical performance, thus elevating the alloy’s potential as a viable material for industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Elucidating the role of surface species in CO oxidation catalyzed by boron nitride nanotube supported transition metal oxides

Boron nitride nanotube (BNNT) is considered a highly promising catalyst support due to its outstanding thermal stability and chemical inertness. These characteristics make BNNT an attractive alternative for high-temperature applications. However, most studies to date have focused on incorporating platinum group metals (PGMs) to achieve high activity. Although BNNT-supported PGM catalysts are highly effective, their scarcity and high cost hinder widespread use in industrial processes. In this study, BNNT-supported transition metal oxides (TMO x /BNNT; TM = Fe, Co, Ni, and Cu) catalysts were investigated, and CO oxidation was applied as a model reaction to evaluate their catalytic performance. Several characterization techniques, including SEM-EDX, TEM, SXRD, H 2 -TPR, and XPS, were employed to examine their physicochemical properties. Notably, the particle size of the metal oxides differed significantly depending on the metal type. This variation is primarily attributed to the inherent metal–support interactions and the thermodynamic stability of each oxide during synthesis. These properties also affected catalytic activity, and various parameters, such as oxygen mobility and redox behavior, played important roles in determining performance. Finally, in situ DRIFTS, CO-TPSR, reaction-order analysis, and 18 O 2 isotope-labeling experiment were used to investigate the reaction mechanism. In conclusion, the findings provide insights into the design of cost-effective BNNT-supported catalysts and highlight their potential applicability in oxidation reactions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗
DOE OSTI2021

Modified microstructures in proton irradiated dual phase 308L weldment filler material

In this study, the effect of proton irradiation on the microstructure of δ ferrite—γ austenite mixed phase 308L filler material in a 508–304 dissimilar metal weldment was investigated over a depth of 0 to 10 µm. Ni–Si–Mn G-phase precipitates were observed with SEM and TEM in δ ferrite but not in γ austenite. Our density functional theory based calculations show that the G/Fe interface energy in δ-Fe is significantly lower than that in γ-Fe (0.35 versus 1.25 J/m 2 ), which provides a thermodynamics-based explanation for our experimental observations of preferential formation of G-phase in δ ferrite. STEM-EDS, TEM dark field imaging, and diffraction patterns confirmed the Ni–Si–Mn enriched precipitates were G-phase precipitates with a stoichiometry of Mn 6 Ni 16 Si 7 . Intragranular voids and Ni–Si enriched clusters were observed in irradiated γ austenite. Additionally, Ni and Si segregation was observed along the void interfaces. In both cases, Ni–Si clusters and segregation to voids, selected area diffraction patterns did not reveal the existence of a second phase. Proton irradiation induced Cr depletion and Si and Ni enrichment at γ-γ austenite grain boundaries that was characterized with STEM/EDS.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Electron microscopy characterization of the fuel-cladding interaction in medium burnup annular fast reactor MOX

In this work, we present electron microscopy data focused on the fuel-cladding interaction layer in annular fast reactor MOX with HT-9 cladding at medium burnup. In agreement with previous literature data, the volatile fission products Cs, Te and I have migrated radially into the extreme fuel periphery and partially interacted with the cladding. The accumulation of Cs has occurred in the outermost rim of the fuel pellet, where grain recrystallization has also been observed. Significant amounts of Pd have been found in the interaction zone, particularly in the sample taken from the upper half of the fissile column where the cladding temperatures are higher. At this axial location, Cr has been enriched at the cladding inner surface and diffused into the fuel. Furthermore, chromium remains mainly in metallic form, but locally formed oxides. The fission products Cs, Te and I are found, with variable composition, in form of nanocrystalline regions dispersed in the metallic Cr-rich layer. The morphology and chemical characteristics of the layer suggest a non-oxidative corrosion mechanism as principal cladding degradation phenomenon occurring in this sample, with local onset of Cr oxidation within the nanocrystalline precipitates.

36 MATERIALS SCIENCE↗