Search NASA⌕ Search

SEARCH · Search NASA

Results for “THERMAL DISSOCIATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Measuring Sodium Chloride Contents of Aerosols

Amount of sodium chloride in individual aerosol particles measured in real time by analyzer that includes mass spectrometer. Analyzer used to determine mass distributions of active agents in therapeutic or diagnostic aerosols derived from saline solutions and in analyzing ocean spray. Aerosol particles composed of sodium chloride introduced into oven, where individually vaporized on hot wall. Vapor molecules thermally dissociated, and some of resulting sodium atoms ionized on wall. Ions leave oven in burst and analyzed by spectrometer, which is set to monitor sodium-ion intensity.

Sinha, M. P.↗
NASA NTRS1991

Thermal design of a Mars oxygen production plant

The optimal design of the thermal components of a system that uses carbon dioxide from the Martian atmosphere to produce oxygen for spacecraft propulsion and/or life support is discussed. The gases are pressurized, heated and passed through an electrochemical cell. Carbon dioxide is reduced to carbon monoxide and oxygen due to thermal dissociation and electrocatalysis. The oxygen thus formed is separated from the gas mixture by the electrochemical cell. The objective of the design is to optimize both the overall mass and the power consumption of the system. The analysis shows that at electrochemical cell efficiencies of about 50 percent and lower, the optimal system would require unspent carbon dioxide in the exhaust gases to be separated and recycled. Various methods of efficiently compressing the intake gases to system pressures of 0.1 MPa are investigated. The total power requirement for oxygen production rates of 1, 5, and 10 kg/day at various cell efficiencies are presented.

Sridhar, K. R.↗
NASA NTRS1993

Planar imaging of OH density distributions in a supersonic combustion tunnel

Images of absolute OH number density were obtained using planar laser-induced fluorescence (PLIF) in a supersonic H2-air combustion tunnel. A tunable KrF excimer laser was used to excite the Q2(11) ro-vibronic line. Calibration of the PLIF images was obtained by referencing the signal measured in the flame to that obtained by the excitation of OH produced by thermal dissociation of H2O in an atmospheric furnace. Measurement errors due to uncertainty in internal furnace atmospheric conditions and image temperature correction are estimated.

Quagliaroli, T. M.↗
NASA NTRS1993

Extraction of oxygen from the Mars atmosphere using glow-discharge and permeation techniques

Oxygen can be extracted from carbon dioxide via thermal dissociation at elevated temperatures. However, temperatures in excess of 1000 K are needed to effect significant levels of dissociation. The experiments reported here have examined the feasibility of using a glow-discharge in low-pressure carbon dioxide to produce increased atomic oxygen yields at lower temperatures (on the order of 800 K). The experiments have shown that when silver membranes are used simultaneously as anodes for the glow discharge and as permeable membranes for oxygen separation, oxygen yields which are comparable to the permeation rates for pure oxygen, can be produced. Since the silver membrane can be employed as the electrode interface between Mars atmosphere and a stabilized-zirconia electrochemical pump, glow-discharge enhancement can be considered as a complementary technology which can be used with the zirconia-based oxygen extraction systems described previously by others. Not only can glow-discharge be used to increase oxygen yields at lowered temperatures, but it can also be considered as a possible way to avoid filtration and compression of Mars atmosphere, since the glow-discharge can be sustained in Mars ambient pressures.

Wu, Dongchuan↗
NASA NTRS1993

Activation of extended red emission photoluminescence in carbon solids by exposure to atomic hydrogen and UV radiation

We report on new laboratory results which relate directly to the observation of strongly enhanced extended red emission (ERE) by interstellar dust in H2 photodissociation zones. The ERE has been attributed to photoluminescence by hydrogenated amorphous carbon (HAC). We are demonstrating that exposure to thermally dissociated atomic hydrogen will restore the photoluminescence efficiency of previously annealed HAC. Also, pure amorphous carbon (AC), not previously photoluminescent, can be induced to photoluminesce by exposure to atomic hydrogen. This conversion of AC into HAC is greatly enhanced by the presence of UV irradiation. The presence of dense, warm atomic hydrogen and a strong UV radiation field are characteristic environmental properties of H2 dissociation zones. Our results lend strong support to the HAC photoluminescence explanation for ERE.

Furton, Douglas G.↗
NASA NTRS1994

Application of Chlorine-Assisted Chemical Vapor Deposition of Diamond at Low Temperatures

Low temperature deposition of diamond has been achieved by a chlorine-assisted diamond chemical vapor deposition (CA-CVD) process. This method begins with the thermal dissociation of molecular chlorine into atomic chlorine in a resistively heated graphite furnace at temperatures between 1300 and 1500 deg. C. The atomic chlorine, upon mixing, subsequently reacts with molecular hydrogen and hydrocarbons. The rapid exchange reactions between the atomic chlorine, molecular hydrogen, and hydrocarbons give rise to the atomic hydrogen and carbon precursors required for diamond deposition. Homoepitaxial diamond growth on diamond substrates has been studied over the substrate temperature range of 100-950 C. It was found that the diamond growth rates are approximately 0.2 microns/hr in the temperature range between 102 and 300 C and that the growth rates do not decrease significantly with a decrease in substrate temperature. This is unique because the traditional diamond deposition using H2/CH4 systems usually disappears at substrate temperatures below approx. 500 deg. C. This opens up a possible route to the deposition of diamond on low-melting point materials such as aluminum and its alloys.

Pan, Chenyu↗
NASA NTRS1997

Theoretical Characterization of the NNO...O3 and NNO...O Complexes

The bonding mechanisms and bond strengths of complexes between two molecular and/or atomic species will be discussed. The implications of complex formation for stratospheric chemistry will be presented. Results of theoretical calculations on NNO ... O3 and NNO ...O will be used as specific examples to illustrate the principles of complex formation. The equilibrium structures and binding energies of these complexes will be presented as well as shifts in other molecular properties due to complexation, such as vibrational frequencies. Thermal dissociation rates will be presented. The theoretical methodology used in this study consists of high-level coupled-cluster calculations and more approximate density functional theory approaches, together with large one-particle basis sets.

Lee, Timothy J.↗
NASA NTRS1981

Non-thermal O/1D/ produced by dissociative recombination of O2/+/ - A theoretical model and observational results

Thermal and nonthermal O(1D) number density profiles are calculated. The two populations are assumed to be coupled by a thermalization cross-section which determines the loss and production in the nonthermal and thermal populations, respectively. The sources, sinks and transport of the two populations are used to model volume emission rate profiles at 6300 A. The 6300 A brightness measured by the Visible Airglow Experiment is then used to establish the presence of the nonthermal population and to determine the thermalization cross-section.

Schmitt, G. A.↗
NASA NTRS1990

Measurement of threshold temperature effects in dissociative electron attachment to HI and DI

From accurate spectroscopic constants it is found that the thermal dissociative-attachment process (DA) in DI should be exothermic only for rotational levels J greater than 8 in v = O. Here, measurement of an enhancement of DA with rotational temperature T in the range 298-468 K is reported. The effect is easily accounted for by the increase in total fractional population of excited J levels in DI relative to HI. The effect affords a rotational analog to the use of vibrationally excited molecules (e.g., HCl) in a plasma to control electron conduction.

Chutjian, A.↗
NASA NTRS1965

Thermal decomposition of clcn.

Shock tube study of thermal decomposition of cyanogen chloride using specific cyanide absorption spectroscopy

CHEMICAL KINETICS↗
NASA NTRS2016

Comparison of Quantum Mechanical and Empirical Potential Energy Surfaces and Computed Rate Coefficients for N2 Dissociation

Comparisons are made between potential energy surfaces (PES) for N2 + N and N2 + N2 collisions and between rate coefficients for N2 dissociation that were computed using the quasiclassical trajectory method (QCT) on these PESs. For N2 + N we compare the Laganas empirical LEPS surface with one from NASA Ames Research Center based on ab initio quantum chemistry calculations. For N2 + N2 we compare two ab initio PESs (from NASA Ames and from the University of Minnesota). These use different methods for computing the ground state electronic energy for N4, but give similar results. Thermal N2 dissociation rate coefficients, for the 10,000K-30,000K temperature range, have been computed using each PES and the results are in excellent agreement. Quasi-stationary state (QSS) rate coefficients using both PESs have been computed at these temperatures using the Direct Molecular Simulation of Schwartentruber and coworkers. The QSS rate coefficients are up to a factor of 5 lower than the thermal ones and the thermal and QSS values bracket the results of shock-tube experiments. We conclude that the combination of ab initio quantum chemistry PESs and QCT calculations provides an attractive approach for the determination of accurate high-temperature rate coefficients for use in aerothermodynamics modeling.

quasiclassical trajectory method↗