SEARCH · Search NASA

Results for “TTT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Assessment of Coupling One-Dimension and Three-Dimension CFD in Conjugate Heat Transfer Modeling and Simulations for Cooling of Turbine Engine

The CHT (conjugate heat transfer) modeling and simulation work fits under a bigger area in the TTT (Transformational Tools and Technologies) project called “Cooling Tools and Technologies for Combustor and Turbine.” The existing validation data sets such as TTT GRC (Glenn Research Center) THX (Turbulent Heat FLUX) IV experiments will be used to assess the solid/fluid heat transfer development and validation. The experimental configuration was a subsonic convergent nozzle with a square exit blowing a heated exhaust over an effusion-cooled deck. The simulation solutions were obtained and compared to experimental measurements of the profiles of flow velocities and temperatures, as well as deck surface temperatures. Cooling air blowing ratios of 0, 1, and 2 were considered. The three-dimensional cooling tubes were modelled by the medial axis of the cylindrical geometries due to large length over width ratios. It represented a typical coupling of one-dimension and three-dimension simulations of conjugate heat transfer approaches. The surface temperatures on the solid surfaces and the profiles of velocities and temperatures near the surfaces compared to the experimental data were presented.

nonlinear sub-filter stresses↗

NASA NTRS1978

The formation kinetics of lunar glasses

The kinetic treatment of crystallization and glass formation, involving the construction of time-temperature-transformation curves (TTT) corresponding to a given degree of crystallinity, is extended to permit the description of crystallization of a body initially cooled to a glassy state. The key assumption is that if at any time and temperature a crystallite is smaller than the critical size corresponding to that temperature, it will melt completely and can be ignored in any further calculations of the crystal distribution. This approach is used to predict the temperature of maximum crystallization rate for the matrix composition of lunar breccia 67975; results are shown to be in excellent agreement with experiment. Theoretical results obtained for anorthite indicate a barrier to nucleation in the range of 75 kT when the ratio of the undercooling to the liquidus temperature is 0.2. Measured nucleation barriers for the 67975 matrix composition are in the range of 42 to 45 kT.

Uhlmann, D. R.↗

NASA NTRS1992

A kinematic analysis of the modified flight telerobotic servicer manipulator system

A reverse kinematic analysis is presented of a six-DOF subchain of a modified seven-DOF flight telerobotic servicer manipulator system. The six-DOF subchain is designated as a TR-RT chain, which describes the sequence of manipulator joints beginning with the first grounded hook joint (universal joint) T, where the sequence R-R designates a pair of revolute joints with parallel axes. At the outset, it had been thought that the reverse kinematic analysis would be similar to a TTT manipulator previously analyzed, in which the third and fourth joints intersected at a finite point. However, this is shown not the case, and a 16th-degree tan-half-angle polynomial is derived for the TR-RT manipulator.

Crane, Carl↗

NASA NTRS1992

Removal of surface loop from stitched composites can improve compression and compression-after-impact strengths

Stitching through-the-thickness (TTT) of composite materials produces a surface loop of yarn between successive penetrations. The surface loop is pressed into the surface layers of the composite material during the curing of the laminate, kinking the in-plane fibers near the surface of the material. The compression strength and compression-after-impact (CAI) strengths of carbon-epoxy specimens were measured with and without the surface loop. Removal of the surface loop had no influence on failure mode or failure mechanism, but did significantly increase the compression and CAI strengths.

Farley, Gary L.↗

NASA NTRS2000

Thermophysical Property Measurement and Materials Research in the NASA/MSFC Electrostatic Levitator

Containerless processing is an important tool for thermophysical property measurements and materials research. The freedom from a crucible allows processing of liquid materials in a metastable undercooled state, as well as allowing processing of high temperature and highly reactive melts. Electrostatic levitation (ESL) is a containerless method which provides a number of unique advantages, including the decoupling of positioning force from sample heating, the ability to operate in ultra-high vacuum or at moderate gas pressure (approximately 3 atm), and the ability to process non-conducting materials. ESL also has the potential to reduce internal flow velocities below those possible with electromagnetic, acoustic, or aero-acoustic techniques. The ESL facility at NASA's Marshall Space Flight Center (MSFC) is in use for thermophysical property measurements and materials research by a number of different internal and external investigators. The methods for obtaining access to the facility, as well as a summary of current capabilities and some future directions will be discussed. In electrostatic levitation, the acceleration of gravity (or residual acceleration in reduced gravity) is opposed by the action of an applied electric field on a charged sample. This positioning method is applicable to any material which can be electrically charged, whether solid or liquid, conducting, or insulating. Because the position of the sample is unstable, a 3-dimensional active control loop rapidly adjusts the applied field to maintain levitation and minimize motion of the sample. Heating lasers melt the sample, and may be adjusted to maintain specified thermal profiles. Microgravity allows electrostatic levitation to work even more effectively. With the need to cancel less than 1 milli-g, the applied field required is reduced from approximately 10 MV/m to approximately 10 kV/m. Alternatively, a microgravity ESL can position larger samples than is possible on the ground, or it can position samples which maintain their charge poorly. Microgravity also reduces the effects of buoyant convection and sedimentation. In the MSFC ESL, many different classes of experiments and measurements have been demonstrated in collaboration with many investigators. These capabilities include heat capacity measurement, phase diagram determination, and nucleation and growth experiments including nucleation rate, TTT curves, and phase selection. We have demonstrated the capability of triggering recalescence of an undercooled liquid sample without loss of levitation. Currently under development are techniques for measuring the surface tension, viscosity, and density of levitated samples, as well as other thermophysical properties. Expanded levitation capabilities including various gas environments for sample processing, sample rotation control and management of thermal gradients are under development for the MSFC ESL. Containerless processing allows research on materials which may not be processed any other way. Electrostatic levitation extends the range of containerless processing to include many materials and classes of materials which cannot be processed by conventional electromagnetic, acoustic, or aerodynamic levitation techniques.

Rogers, Jan↗

NASA NTRS2002

Thermophysical Property Measurements in the MSFC ESL

Electrostatic Levitation (ESL) is an advanced technique for containerless processing of metals, ceramics, and semiconductors. Because no container is required, there is no contamination from reaction with a crucible, allowing processing of high temperature, highly reactive melts. The high vacuum processing environment further reduces possible contamination of the samples. Finally, there is no container to provide heterogeneous nucleation sites, so the undercooled range is also accessible for many materials. For these reasons, ESL provides a unique environment for measuring thermophysical properties of liquid materials. The properties that can be measured in ESL include density, surface tension, viscosity, electrical and thermal conductivity, specific heat, phase diagram, TTT- and CCT- curves, and other thermodynamic properties. In this paper, we present data on surface tension and viscosity, measured by the oscillating drop technique, and density, measured by an automated photographic technique, measured in the ESL at NASA Marshall Space Flight Center.

Hyers, R. W.↗

NASA NTRS2002

Building the Capacity of HBCU's for Establishing Effective Globe Partnerships

The special GLOBE train-the-trainer (TTT) workshop entitled "Building the Capacity of HBCUs For Establishing Effective GLOBE Partnerships" was help for the purpose of expanding GLOBE training capacity on the campuses of Historically Black Colleges and Universities (HBCUs) and community colleges (CCs). The workshop was held March 17-22, 2002 in Washington, D.C. at Howard University. It was designed to establish research and instructional collaboration between and among U.S. universities (HBCUs and CCs) and African countries. Representatives from 13 HBCUs, and two community colleges were represented among trainees, so were representatives from eight African countries who were financially supported by other sources. A total of 38 trainees increased their knowledge of GLOBE protocols through five days of rigorous classroom instruction, field experiences, cultural events, and computer lab sessions.

Bagayoko, Diola↗

NASA NTRS1998

The effect of track structure on the induction of chromosomal aberrations in murine cells

PURPOSE: To measure chromosome aberrations in C3H 10T1/2 mouse fibroblasts using FISH painting at the first mitosis following exposure to 30 keV/microm hydrogen or neon ions. MATERIALS AND METHODS: Cells in plateau-phase were irradiated with 0.86 MeV protons at the TTT-3 Tandem accelerator in Naples (Italy), or with 400 MeV/n Ne ions at the HIMAC accelerator in Chiba (Japan). Colcemid-blocked cells were harvested at the first mitosis following exposure, and chromosome spreads were hybridized in situ with a fluorescein-labelled composite mouse DNA probe specific for chromosomes 2 and 8. RESULTS: Protons were more efficient than neon ions at the same LET in the induction of chromosome interchanges and breaks. Yields of complex exchanges were similar for both particles at the same dose, but protons produced mostly insertions, while with Ne exposure non-reciprocal exchanges were the most frequent complex-type exchange. CONCLUSIONS: Charged particles with the same LET produce different yields of chromosome aberrations, and some observed differences can be explained based on the available track-structure models.

NASA Center JSC↗

NASA NTRS1992

Numerical classification of coding sequences

DNA sequences coding for protein may be represented by counts of nucleotides or codons. A complete reading frame may be abbreviated by its base count, e.g. A76C158G121T74, or with the corresponding codon table, e.g. (AAA)0(AAC)1(AAG)9 ... (TTT)0. We propose that these numerical designations be used to augment current methods of sequence annotation. Because base counts and codon tables do not require revision as knowledge of function evolves, they are well-suited to act as cross-references, for example to identify redundant GenBank entries. These descriptors may be compared, in place of DNA sequences, to extract homologous genes from large databases. This approach permits rapid searching with good selectivity.

Non-NASA Center↗

NASA NTRS2006

Method of Estimating Continuous Cooling Transformation Curves of Glasses

A method is proposed for estimating the critical cooling rate and continuous cooling transformation (CCT) curve from isothermal TTT data of glasses. The critical cooling rates and CCT curves for a group of lithium disilicate glasses containing different amounts of Pt as nucleating agent estimated through this method are compared with the experimentally measured values. By analysis of the experimental and calculated data of the lithium disilicate glasses, a simple relationship between the crystallized amount in the glasses during continuous cooling, X, and the temperature of undercooling, (Delta)T, was found to be X = AR(sup-4)exp(B (Delta)T), where (Delta)T is the temperature difference between the theoretical melting point of the glass composition and the temperature in discussion, R is the cooling rate, and A and B are constants. The relation between the amount of crystallisation during continuous cooling and isothermal hold can be expressed as (X(sub cT)/X(sub iT) = (4/B)(sup 4) (Delta)T(sup -4), where X(sub cT) stands for the crystallised amount in a glass during continuous cooling for a time t when the temperature comes to T, and X(sub iT) is the crystallised amount during isothermal hold at temperature T for a time t.

Zhu, Dongmei↗

NASA NTRS2017

CFD Analysis in Advance of the NASA Juncture Flow Experiment

NASA through its Transformational Tools and Technologies Project (TTT) under the Advanced Air Vehicle Program, is supporting a substantial effort to investigate the formation and origin of separation bubbles found on wing-body juncture zones. The flow behavior in these regions is highly complex, difficult to measure experimentally, and challenging to model numerically. Multiple wing configurations were designed and evaluated using Computational Fluid Dynamics (CFD), and a series of wind tunnel risk reduction tests were performed to further down-select the candidates for the final experiment. This paper documents the CFD analysis done in conjunction with the 6 percent scale risk reduction experiment performed in NASA Langley's 14- by 22-Foot Subsonic Tunnel. The combined CFD and wind tunnel results ultimately helped the Juncture Flow committee select the wing configurations for the final experiment.

Flow Experiment↗

NASA NTRS2018

2040 Vision: A Roadmap for Integrated, Multiscale Materials and System Modeling and Simulation

Over the last few decades, advances in high-performance computing, new materials characterization methods, and, more recently, an emphasis on integrated computational materials engineering (ICME) and additive manufacturing have been a catalyst for multiscale modeling and simulation-based design of materials and structures in the aerospace industry. While these advances have driven significant progress in the development of aerospace components and systems, that progress has been limited by persistent technology and infrastructure challenges that must be overcome to realize the full potential of integrated materials and systems design and simulation modeling throughout the supply chain. As a result, NASA's Transformational Tools and Technology (TTT) Project sponsored a study (performed by a team led by Pratt & Whitney) to define the potential 25-year future state required for integrated multiscale modeling of materials and systems (e.g., load-bearing structures) to accelerate the pace and reduce the expense of innovation in future aerospace and aeronautical systems. This talk will describe the findings of this 2040 Vision study (e.g., the 2040 vision state; the required interdependent core technical work areas, Key Element (KE); associated critical gaps and actions to close those gaps; and major recommendations). This roadmap is a community consensus document and is a result of over 450 professionals input obtain via: i) four society workshops (AIAA, NAFEMS, and two TMS), ii) community-wide survey, and iii) the establishment of 9 expert panels (one per key element) consisting on average 10 non-team members from academia, government and industry to review, update content, and prioritize gaps and actions. It is NASA's hope and desire that this roadmap provides the strategic guidance to both public and private research and development decision makers to make the proposed 2040 vision state a reality and thereby provide a significant advancement in the United States global competitiveness.

Multiscale Modeling↗

NASA NTRS2017

CFD Analysis in Advance of the NASA Juncture Flow Experiment

NASA through its Transformational Tools and Technologies Project (TTT) under the Advanced Air Vehicle Program, is supporting a substantial effort to further investigate the formation and origin of separation bubbles found on wing-body juncture zones. The flow behavior in these regions is highly complex, difficult to measure experimentally, and challenging to model numerically. Multiple wing configurations were designed and evaluated using Computational Fluid Dynamics (CFD), and a series of wind tunnel risk reduction tests were performed to further down-select the candidates for the final experiment. This paper documents the CFD analysis done in conjunction with the 6 percent scale risk reduction experiment performed in NASA Langley’s 14- by 22-Foot Subsonic Tunnel. The combined CFD and wind tunnel results ultimately help the Juncture Flow committee select the wing configurations for the final experiment.

Lee, H. C.↗

NASA NTRS2020

An Overview of NASA’s Learn-to-Fly Technology Development

“Learn-to-Fly” (L2F) is an advanced technology development effort within the Modeling and Control for Agile Aircraft Development (MCAAD) group, a part of the NASA Transformative Aeronautics Concepts Program’s (TACP) Transformational Tools and Technologies (TTT) project. The goal of L2F is to develop technologies for enabling self-learning flight vehicles, using both ground- and flight-test approaches. Specifically, research has been conducted to demonstrate the potential to merge two enabling technologies, real-time aerodynamic modeling and adaptive flight controls, to substantially reduce the typical ground- and flight-testing time requirements for air vehicle design. This effort involved development of real-time, on-board algorithms to demonstrate key L2F technologies including aerodynamic modeling and control for an aircraft with minimal a priori knowledge. This research included both ground-based wind tunnel experiments utilizing modern design of experiments (DOE) techniques, as well as a flight test campaign, and was intended to rapidly advance these technologies and demonstrate key capabilities of the L2F approach. This paper presents the overview of the methods used to develop L2F technologies in NASA Langley Research Center’s 12-Foot Low Speed Tunnel, as well as in flight experiments. These methods include efficient wind tunnel data collection, real-time global nonlinear aerodynamic modeling in both the time and frequency domains, and the integration of the modeling techniques with adaptive flight controls, all of which were demonstrated using experimental validation.

Stephen E Riddick↗

NASA NTRSDate not supplied

Dynamic Vehicle Assessment for Intelligent Contingency Management of Urban Air Mobility Vehicles

New algorithms will be required to ensure passenger and bystander safety during the expected era of autonomous urban air mobility (UAM) aircraft. This paper examines an approach for assessing the vehicle capability to fly itself and to complete a mission safely. The concepts combine elements of system identification, adaptive control, flight dynamics, envelope predictions, and handling qualities, as well as human pilot intuition. The approach is applied to a simulation of a generic distributed electric propulsion urban air mobility-type aircraft, which was developed under the NASA Transformational Tools and Technologies (TTT) project, Autonomous Systems / Intelligent Contingency Management subproject.

flight envelope↗

NASA NTRSDate not supplied

Controlling properties by chemistry in doped shape memory alloys

Shape memory alloys find increasing use in airspace applications. Using theoretical and computational methods, we investigate correlations between the selected properties and composition in doped NiTi-based shape memory alloys. Among the properties we consider relative energies, phase transition temperature, and hysteresis. We compare predictions to experimental data. Our theoretical guidance facilitates design of future alloys. We acknowledge support from the NASA Transformative Aeronautics Concepts Program, Transformational Tools & Technologies (TTT) Project.

NiTi↗

NASA NTRSDate not supplied

Dynamic Vehicle Assessment for Intelligent Contingency Management for Urban Air Mobility Vehicles

flight envelope prediction↗

NASA NTRS2021

Modeling of the Influence of Thermally Grown Oxide (TGO) Layers on the Driving Forces in Environmental Barrier Coating Systems

Environmental barrier coatings (EBC) are an enabling technology for the successful application of ceramic matrix composites (CMCs) in air-breathing gas turbine engines. EBCs are susceptible to several failure modes including oxidation/delamination, recession, chemical attack and dissolution, thermomechanical degradation, erosion, and foreign object impact damage in a combustion environment. Spallation of environmental barrier coating (EBC), induced by a thermally grown oxide (TGO) layer, is a key EBC failure mode. The TGO layer, resulting from steam oxidation, grows either from a silicon bond coat layer (if present) or from a silicon carbide (SiC) based substrate itself. The TGO layer evolves (i.e., thickness increases with time) as water vapor and oxygen gradually diffuse through the EBC, and the EBC spalls off once the TGO layer reaches some critical thickness. The critical thickness of the TGO layer for failure is in the range of 20-30 microns, with the actual value depending upon exposure temperature, microstructure, etc. Current work at NASA Glenn Research Center, under the Transformative Tools and Technology (TTT) subproject is aimed at addressing associated failure modes in EBC systems and developing robust analysis tools to aid in the design/analysis of these systems. The objective of the current work is to conduct a sensitivity study to examine the influence of uniformly and non-uniformly grown oxide layers on the associated driving forces leading to spallation of the EBC when subjected to isothermal loading. The effect of damage in the TGO layer on the resulting stress states is also assessed both in uniform and non-uniform TGO layers.

Coatings↗