Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tail”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

Wind-Tunnel Investigation of the Low-Speed Characteristics of a 1/8-Scale Model of the Republic XP-91 Airplane with a Vee and a Conventional Tail. Addendum - Characteristics with a Revised Conventional Tail and Drooped Wing Tips

Additional wind-tunnel tests were made of a 1/8-scale model of the Republic XP-91 airplane to determine its characteristics with various modifications. The modifications included a revised conventional tail, revised rocket arrangement, drooped wing tips, and revised landing gear and doors. Tests were also made to determine the effectiveness of the control surfaces of the model with the conventional tail and the effect of changing wing incidence and tail length. The revised rocket arrangement provided a considerable increase in the static directional stability contributed by the vee tail at small angles of yaw. The conventional tail provided a greater static directional stability than the vee tail without increasing the rolling moment due to sideslip. The rolling moment die to sideslip was considerable reduced by either drooped wing tips or open main landing-gear doors. The reduction in rolling moment due to sideslip resulting from the drooped tips was less with the landing-gear doors open than with the doors closed. A change in wing incidence from 0 degrees to 6 degrees reduced the elevator angle required for balance by approximately 6 degrees.

Weiberg, James A.↗
NASA NTRS1991

Magnetic properties of the high-latitude tail boundary - Draping of magnetosheath field lines and tail-aligned current

Magnetic properties of the high-latitude tail boundary are examined with IMP 8 magnetometer data. The high-latitude tail boundary separates the tail lobe from the magnetosheath. Magnetic fields are stable in the tail lobe, but very irregular in the magnetosheath. Boundary crossings are marked by the rotation of magnetic components parallel to the boundary plane. The magnetic component normal to the boundary, if any, is very small in comparison to this rotational change. Despite large magnetic fluctuations in the magnetosheath, the magnetosheath-side field orientation is consistent with the draping of the IMF against the magnetotail. The boundary current has a component parallel to the lobe field (tail-aligned current), as well as a circumferential component. The IMF orientation controls the sheath-side B(Y), while the lobe-side field has a more rigid configuration flaring antisunward.

Ohtani, S.↗
NASA NTRS2002

Helicopter Tail Boom With Venting for Alleviation and Control of Tail Boom Aerodynamic Loads and Method Thereof

In at least one embodiment, the apparatus of the invention is a flight vehicle tail assembly having an exterior surface, at least one first vent in the exterior surface, at least one second vent in the exterior surface, and an air passage connecting the at least one first vent to the at least one second vent allowing air to flow there between. Where the at least one first vent is located near a high air pressure area acting on the exterior surface during a range of predefined flight conditions, Further, the at least one second vent is located near a low air pressure area acting on the exterior surface during the predefined flight conditions. So that at the predefined flight conditions adverse loads on the tail assembly are reduced by venting air from the high pressure area, through the tail assembly, to the low pressure area. The method of the present invention includes the steps of: receiving air through the at least one first vent in the exterior surface, passing the air through the tail assembly from the at least one first vent to at least one second vent in the exterior surface. and ejecting the air out of the tail assembly at the at least one second vent.

Daniel W Banks↗
NASA NTRS1961

Investigation at High Subsonic Speeds of the Use of Low Auxiliary Tail Surfaces having Dihedral to Improve the Longitudinal and Directional Stability of a T-Tail Model at High Lift

An investigation of the use of low auxiliary horizontal-tail surfaces to alleviate the pitch-up tendency at high lift of an airplane configuration having a T - tail has been conducted in the Langley high-speed 7- by 10-foot tunnel. The basic model had a wing with an aspect ratio of 3, a taper ratio of 0.143, and an unswept 80-percent chord line. The Mach number for most of the tests extended from 0.60 to 0.94 and the angle-of-attack range was from -2 deg. to approximately 24 deg. at the lowest test Mach number. A preliminary study of a systematic series of auxiliary tails indicated that the pitch-up tendency at high lift encountered on the basic model could be greatly alleviated by use of a relatively small, very low-aspect-ratio auxiliary horizontal tail. This tail was located radially with respect to the fuselage center line with 30 deg. negative dihedral and therefore provided a significant favorable increment to directional stability of the model throughout most of the test angle-of-attack range.

Sleeman, William C., Jr.↗
NASA NTRS1997

Vertical Tail Buffeting Alleviation Using Piezoelectric Actuators: Some Results of the Actively Controlled Response of Buffet-Affected Tails (ACROBAT) Program

A 1/6-scale F-18 wind-tunnel model was tested in the Transonic Dynamics Tunnel at the NASA Langley Research Center as part of the Actively Controlled Response Of Buffet Affected Tails (ACROBAT) program to assess the use of active controls in reducing vertical tail buffeting. The starboard vertical tail was equipped with an active rudder and the port vertical tail was equipped with piezoelectric actuators. The tunnel conditions were atmospheric air at a dynamic pressure of 14 psf. By using single-input-single-output control laws at gains well below the physical limits of the actuators, the power spectral density of the root strains at the frequency of the first bending mode of the vertical tail was reduced by as much as 60 percent up to angles of attack of 37 degrees. Root mean square (RMS) values of root strain were reduced by as much as 19 percent. Buffeting alleviation results when using the rudder are presented for comparison. Stability margins indicate that a constant gain setting in the control law may be used throughout the range of angle of attack tested.

Moses, Robert W.↗
NASA NTRS1997

Active Vertical Tail Buffeting Alleviation on a Twin-Tail Fighter Configuration in a Wind Tunnel

A 1/6-scale F-18 wind-tunnel model was tested in the Transonic Dynamics Tunnel at the NASA Langley Research Center as part of the Actively Controlled Response Of Buffet-Affected Tails (ACROBAT) program to assess the use of active controls in reducing vertical tail buffeting. The starboard vertical tail was equipped with an active rudder and other aerodynamic devices, and the port vertical tail was equipped with piezoelectric actuators. The tunnel conditions were atmospheric air at a dynamic pressure of 14 psf. By using single-input-single-output control laws at gains well below the physical limits of the control effectors, the power spectral density of the root strains at the frequency of the first bending mode of the vertical tail was reduced by as much as 60 percent up to angles of attack of 37 degrees. Root mean square (RMS) values of root strain were reduced by as much as 19 percent. Stability margins indicate that a constant gain setting in the control law may be used throughout the range of angle of attack tested.

Moses, Robert W.↗
DOE OSTI2021

Numerical simulation of the hot-tail runaway electron production mechanism using CQL3D and comparison with Smith–Verwichte analytical model

Abstract The hot-tail mechanism of runaway electron (RE) production (Harvey et al 2000 Phys. Plasmas 7 4590) is the primary source of RE in the case of rapidly cooling tokamak plasma. Quantifying this mechanism is very important as it can provide most of the post-thermal-quench (TQ) current, or a seed current for the secondary source of RE through the avalanche mechanism. An analytic model which omits pitch-angle scattering is often used in literature for estimating the hot-tail RE density (Smith and Verwichte 2008 Phys. Plasmas 15 072502). In the present study, we use the CQL3D bounce-averaged Fokker–Planck code (Harvey and McCoy 1992 Proc. IAEA Technical Committee Meeting on Advances in Simulation and Modeling of Thermonuclear Plasmas p 527) to test the limits of validity of the model. In particular, we examine the cases of Z = 1 and Z = 18 ions, for sets of different initial temperature, density, electric field and the characteristic time of temperature decay. We show that for Z = 1 plasma, the ratio of RE density computed by CQL3D to that estimated from the model is within 0.6–6.0 in studied cases. For the Z = 18 case, this factor is systematically a much smaller number, typically 0.02–0.6. We suggest a simple correction to the model that narrows down the range of this ratio to 0.3–3.8 in all of the cases, including Z = 1 and Z = 18 plasmas.

Physics↗
NASA NTRS1975

Low speed aerodynamic characteristics of a transport model having 42.33 deg swept low wing with supercritical airfoil, double-slotted flaps, and T-tail or low tail

A low-speed investigation was conducted in the Langley V/STOL tunnel over an angle-of-attack range of approximately 4 deg to 24 deg to determine the static longitudinal stability characteristics and high lift performance of a general research model which represented an advanced subsonic transport configuration. The model had a 42.33 deg swept, aspect ratio 7.05 wing with a supercritical airfoil and high lift system consisting of a leading edge device (slat or Kruger flap) and a double-slotted flap. The flaps were deflected for take off and landing configurations and were not deflected for tests of the clean configuration. The model was tested with the horizontal tail in either a T tail or low tail position. The effects of various arrangements of flowthrough nacelles which represent a three engine configuration (two large wing-mounted nacelles and a vertical tail mounted nacelle) and a four engine configuration (four smaller wing-mounted nacelles) were determined.

Fournier, P. G.↗
NASA NTRS1993

Simulation of tail buffet using delta wing-vertical tail configuration

Computational simulation of the vertical tail buffet problem is accomplished using a delta wing-vertical tail configuration. Flow conditions are selected such that the wing primary-vortex cores experience vortex breakdown and the resulting flow interacts with the vertical tail. This multidisciplinary problem is solved successively using three sets of equations for the fluid flow, aeroelastic deflections and grid displacements. For the fluid dynamics part, the unsteady, compressible, full Navier-Stokes equations are solved accurately in time using an implicit, upwind, flux-difference splitting, finite-volume scheme. For the aeroelastic part, the aeroelastic equation for bending vibrations is solved accurately in time using the Galerkin method and the four-stage Runge-Kutta scheme. The grid for the fluid dynamics computations is updated every few time steps using a third set of interpolation equations. The computational application includes a delta wing of aspect ratio 1 and a rectangular vertical tail of aspect ratio 2, which is placed at 0.5 root-chord length downstream of the wing trailing edge. The wing angle of attack is 35 deg and the flow Mach number and Reynolds number are 0.4 and 10,000, respectively.

Kandil, Osama A.↗
NASA NTRS1945

Experimental verification of a simplified vee-tail theory and analysis of available data on complete models with vee tails

An analysis has been made of available data on vee tail surfaces. Previously published theoretical studies of vee tails have been extended to include the control effectiveness and control forces in addition to the stability. Tests of two isolated tail surfaces with various amounts of dihedral provided a check of the theory. Methods for designing vee tails were also developed and are given in the present paper.

Purser, Paul E↗
NASA NTRS1959

Effect of Tail Dihedral on Lateral Control Effectiveness at High Subsonic Speeds of Differentially Deflected Horizontal-Tail Surfaces on a Configuration having a Thin Highly Tapered Wing

Tests have been conducted in the Langley high-speed 7- by 10-foot tunnel to determine the effect of tail dihedral on lateral control effectiveness of a complete-model configuration having differentially deflected horizontal-tail surfaces. Limited tests were made to determine the lateral characteristics as well as the longitudinal characteristics in sideslip. The wing had an aspect ratio of 3, a taper ratio of 0.14, 28.80 deg sweep of the quarter-chord line with zero sweep at the 80-percent-chord line, and NACA 65A004 airfoil sections. The test Mach number range extended from 0.60 to 0.92. There are only small variations in the roll effectiveness parameter C(sub iota delta) with negative tail dihedral angle. The tail size used on the test model, however, is perhaps inadequate for providing the roll rates specified by current military requirements at subsonic speeds. The lateral aerodynamic characteristics were essentially constant throughout the range of sideslip angle from 12 deg to -12 deg. A general increase in yawing moment was noted with increased negative dihedral throughout the Mach number range.

Fournier, Paul G.↗
NASA NTRS1961

Aerodynamic Loads at Mach Numbers from 0.70 to 2.22 on an Airplane Model Having a Wing and Canard of Triangular Plan Form and Either Single or Twin Vertical Tails: Tabulated Data for the Model with Twin Vertical Tails - Supplement 2

Tabulated results of a wind-tunnel investigation of the aerodynamic loads on a canard airplane model with twin vertical tails are presented for Mach numbers from 0.70 to 2.22. The Reynolds number for the measurements was 2.9 x 10(exp 6) based on the wing mean aerodynamic chord. The results include local static-pressure coefficients measured on the wing, body, and one of the vertical tails for angles of attack from -4 degrees to 16 degree angles of sideslip of 0 degrees and 5.3 degrees, and nominal canard deflections of O degrees and 10 degrees. Also included are section force and moment coefficients obtained from integrations of the local pressures and model-component force and moment coefficients obtained from integrations of the section coefficients. Geometric details of the model are shown and the locations of the pressure orifices are shown. An index to the data contained herein is presented and definitions of nomenclature are given. Detailed descriptions of the model and experiments and a brief discussion of some of the results are given. Tabulated results of measurements of the aerodynamic loads on the same canard model but having a single vertical tail instead of twin vertical tails are presented.

Peterson, Victor L.↗
NASA NTRS1945

Wind-Tunnel Tests of a 1/6-Scale Model of Republic XF-12 Vertical Tail with Stub Fuselage and Stub Horizontal Tail

A 1/6-scale model of the Republic XF-12 vertical tail with stub fuselage and stub horizontal tail was tested in the Langley stability tunnel to determine the aerodynamic characteristics of the model, The investigation included a study of the effects of boundarylayer thickness, rudder area, and cover-plate alinement on the aerodynamic characteristics. Tuft studies were made in the vicinity of the junction of the vertical and stub horizontal tails. The results of the investigation indicated that the flow in the vicinity of the junction of the vertical and stub horizontal tails was only slightly improved by the addition of a fillet. An increase in boundary-layer thickness produced a slight decrease in rudder effectiveness. The increase in lift of the combined rudders over that of the upper rudder alone was not proportional at low deflections and was approximately proportional at high deflections to the increase in rudder area. When the balance-chamber cover plates were bowed out, the change in rudder hinge moment with rudder angle was less negative. The variation of the lift coefficient with angle of attack and the variation, at small values of angle of attack, of rudder hinge-noment coefficient with angle of attack was approximately the same for all model configurations tested. The upper rudder used in conjunction with a tab was found to satisfy the Army specifications regarding asymmetric power on a multiengine airplane.

MacLachlan, Robert↗
NASA NTRS1935

Wing-Fuselage Interference, Tail Buffeting, and Air Flow About the Tail of a Low-Wing Monoplane

This report presents the results of wind tunnel tests on a Mcdonnell Douglas airplane to determine the wing-fuselage interference of a low-wing monoplane. The tests included a study of tail buffeting and the air flow in the region of the tail. The airplane was tested with and without the propeller slipstream, both in the original condition and with several devices designed to reduce or eliminate tail buffeting. The devices used were wing-fuselage fillets, a NACA cowling, reflexed trailing edge of the wing, and stub auxiliary airfoils.

White, James A↗
NASA NTRS1943

Flight Tests of Various Tail Modifications on the Brewster XSBA-1 Airplane II : Measurements of Flying Qualities with Tail Configuration Number Two

Several tail modifications of the Brewster XSBA-1 scout-bomber were investigated and results compared. Modifications consisted of variation of the chord of the elevator and rudder while the total area of the surfaces is kept constant and variations of the total area of the vertical tail surface. Configuration number 2 reduced trim changes by 50 percent and reduced average elevator control force gradient from 30 to 27 pounds/g. Stick travel required to stall in maneuver was 4.6 inches.

STABILITY & CONTROL - BREWSTER SBA-1↗
NASA NTRS1972

Supersonic aerodynamic characteristics of a low-aspect-ratio missile model with wing and tail controls and with tails in line and interdigitated

A study has been made to determine the aerodynamic characteristics of a low-aspect ratio cruciform missile model with all-movable wings and tails. The configuration was tested at Mach numbers from 1.50 to 4.63 with the wings in the vertical and horizontal planes and with the wings in a 45 deg roll plane with tails in line and interdigitated.

Graves, E. B.↗
NASA NTRS1979

Pressure distributions on three different cruciform aft-tail control surfaces of a wingless missile at mach 1.60, 2.36, and 3.70 Volume 1: Trapezoidal tail

The results of pressure distribution tests conducted in the Langley Unitary Plan wind tunnel are presented. The data were obtained for three sets of cruciform aft-tail control surfaces on a wingless missile model at Mach numbers of 1.60, 2.36, and 3.70 for angles of attack from -4 degrees to 20 degrees, model roll angles from 0 degrees to 90 degrees, and tail deflections of 0 degrees and 15 degrees. The test Reynolds number used was 6.6 million per meter.

Lamb, M.↗