Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tensile Strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Thermal Conductivity of Graphene Coated Copper Under Uniaxial Tensile Mechanical Strain

Graphene continues to demonstrate promise as a highly effective barrier coating, even at only one atom thick. The thermal properties of this coating are also promising to allow diffusion of heat across the surface, as the isolated graphene is an intrinsically good thermal conductor, yet this and its behavior under mechanical deformation has been less extensively studied. This report demonstrates that the in-plane thermal conductivity and interfacial thermal conductance of graphene coatings on copper are affected by mechanical strain. By inducing a strain in the copper substrate, the Raman-active 2D peak exhibits a change in position as well as a change in laser power dependence as the copper substrate is uniaxially elongated to a maximum of 0.5%. Non-linear trends in thermal conductivity are observed with tensile strain in samples with differing strain transfer rates from the substrate, indicating the close correlation between intrinsic thermal conduction and interfacial properties in atomically thin coatings transferred onto metals.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ measurement of phase transformations and residual stress evolution during welding using spatially distributed fiber-optic strain sensors

Welding of high-strength steels can result in large tensile strains as the base metal and filler material cool from their molten state. To combat these large tensile strains, low-transformation-temperature (LTT) metal fillers have been proposed. These fillers undergo a martensitic phase transformation at a lower temperature which can ultimately reduce the tensile strain or can even introduce compressive strain adjacent to the weld metal. However, the process for optimizing the composition of the LTT material, as well as various weld parameters for each unique weld geometry, can be quite expensive, especially if the acceptance criterion requires using neutrons, x-ray beams, or destructive techniques to characterize residual stresses. This work describes a simple, low-cost method for quantifying residual stresses and phase transformations in situ during welding. Spatially distributed fiber-optic sensors were bonded to a cast iron plate, along with tack-welded thermocouples, to measure temperature and strain during multiple passes with LTT filler metals. Results show that the fiber-optic sensors can successfully resolve compressive strain adjacent to the weld region caused by the martensitic phase transformations in the LTT filler material.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Molecular beam epitaxy of PdO on MgO (001)

PdO, widely used in catalysis in powder form for decades, has been predicted recently to be a Dirac semimetal. Synthesis of high-quality single crystals of this material is thus of great interest. Here, by using ozone-assisted molecular beam epitaxy, PdO thin films were grown on a MgO (001) substrate. X-ray diffraction and transmission electron microscopy indicate the film is a / b axis oriented, with the c axis lying in plane. Fully oxygenated PdO films have a low density of holelike carriers, and are insulating at the lowest temperatures. Our density functional theory calculations using the Heyd-Scuseria-Ernzerhof exchange-correlation functional suggest a ~1.0 eV band gap at the M point, where the gap can be reduced by tensile strain along the c axis and the bands begin to invert when the tensile strain is as high as 18%. Although tensile strain of this magnitude is experimentally not viable using epitaxy, electrons can be doped by oxygen reduction. Finally, our results emphasize the need for careful consideration of electron correlation effects and stoichiometry in ab initio modeling of topological semimetals involving transition metal oxides.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strain-induced majority carrier inversion in ferromagnetic epitaxial LaCo O 3 - δ thin films

Tensile-strained LaCoO 3-δ thin films are ferromagnetic, in sharp contrast to the zero-spin bulk, although no clear consensus has emerged as to the origin of this phenomenon. While magnetism has been heavily studied, relatively little attention has been paid to electronic transport, due to the insulating nature of the strain-stabilized ferromagnetic state. Here, structure, magnetism, and transport are studied in epitaxial LaCoO 3-δ films (10–22-nm thick) on various substrates (from 1.4% compressive to 2.5% tensile strain), using synchrotron x-ray diffraction, scanning probe and transmission electron microscopy, magnetometry, polarized neutron reflectometry, resistivity, and Hall effect. High quality, smooth films are obtained, exhibiting superstructures associated with both oxygen vacancy ordering and periodic in-plane ferroelastic domains. Consistent with prior work, ferromagnetism with an approximately 80–85 K Curie temperature is observed under tension; polarized neutron reflectometry confirms a relatively uniform magnetization depth profile, albeit with interfacial dead layer formation. Electrical transport is found to have similar semiconducting nature to bulk, but with reduced resistivity and activation energy. Hall effect measurements, however, reveal a striking inversion of the majority carrier type, from p-type in the bulk and under compression to n-type under tension. While thus far overlooked, ferromagnetism in epitaxial LaCoO 3-δ films is thus directly correlated with n-type behavior, providing important insight into the ferromagnetic state in this system. Here, aided by density functional theory calculations, these results are interpreted in terms of tensile-strain-induced orbital occupation and band structure changes, including a rapid decrease in effective mass at the e g -derived conduction band minimum, and corresponding increase at the valence band maximum.

36 MATERIALS SCIENCE↗
NASA NTRS1999

Consequences of Atomic Oxygen Interaction With Silicone and Silicone Contamination on Surfaces in Low Earth Orbit

The exposure of silicones to atomic oxygen in low Earth orbit causes oxidation of the surface, resulting in conversion of silicone to silica. This chemical conversion increases the elastic modulus of the surface and initiates the development of a tensile strain. Ultimately, with sufficient exposure, tensile strain leads to cracking of the surface enabling the underlying unexposed silicone to be converted to silica resulting in additional depth and extent of cracking. The use of silicone coatings for the protection of materials from atomic oxygen attack is limited because of the eventual exposure of underlying unprotected polymeric material due to deep tensile stress cracking of the oxidized silicone. The use of moderate to high volatility silicones in low Earth orbit has resulted in a silicone contamination arrival at surfaces which are simultaneously being bombarded with atomic oxygen, thus leading to conversion of the silicone contaminant to silica. As a result of these processes, a gradual accumulation of contamination occurs leading to deposits which at times have been up to several microns thick (as in the case of a Mir solar array after 10 years in space). The contamination species typically consist of silicon, oxygen and carbon. which in the synergistic environment of atomic oxygen and UV radiation leads to increased solar absorptance and reduced solar transmittance. A comparison of the results of atomic oxygen interaction with silicones and silicone contamination will be presented based on the LDEF, EOIM-111, Offeq-3 spacecraft and Mir solar array in-space results. The design of a contamination pin-hole camera space experiment which uses atomic oxygen to produce an image of the sources of silicone contamination will also be presented.

Banks, Bruce A.↗
NASA NTRS2002

Computational Simulation of the High Strain Rate Tensile Response of Polymer Matrix Composites

A research program is underway to develop strain rate dependent deformation and failure models for the analysis of polymer matrix composites subject to high strain rate impact loads. Under these types of loading conditions, the material response can be highly strain rate dependent and nonlinear. State variable constitutive equations based on a viscoplasticity approach have been developed to model the deformation of the polymer matrix. The constitutive equations are then combined with a mechanics of materials based micromechanics model which utilizes fiber substructuring to predict the effective mechanical and thermal response of the composite. To verify the analytical model, tensile stress-strain curves are predicted for a representative composite over strain rates ranging from around 1 x 10(exp -5)/sec to approximately 400/sec. The analytical predictions compare favorably to experimentally obtained values both qualitatively and quantitatively. Effective elastic and thermal constants are predicted for another composite, and compared to finite element results.

Goldberg, Robert K.↗
DOE OSTI2022

Real-Time Modulation of Hydrogen Evolution Activity of Graphene Electrodes Using Mechanical Strain

This paper reports the effect of mechanically applied elastic strain on the hydrogen evolution reaction (HER) activity of graphene under acidic conditions. Here, applied tensile strain of 0.2% on a graphene electrode is shown to lead to a 1–3% increase of HER current. Tensile strain increases HER activity while compressive strain decreases it. Density functional theory (DFT) calculations using a periodic graphene slab model show increasing in the adsorption energy of H atom with growing tensile strain, leading to a corresponding enhancement of current density in HER, similar to that observed experimentally.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Robust Ferromagnetism in Highly Strained SrCoO 3 Thin Films

Epitaxial strain provides important pathways to control the magnetic and electronic states in transition-metal oxides. However, the large strain is usually accompanied by a strong reduction of the oxygen-vacancy formation energy, which hinders the direct manipulation of their intrinsic properties. Here, using a postdeposition ozone annealing method, we obtain a series of oxygen stoichiometric SrCoO 3 thin films with the tensile strain up to 3.0%. We observe a robust ferromagnetic ground state in all strained thin films, while interestingly the tensile strain triggers a distinct metal-to-insulator transition along with the increase of the tensile strain. The persistent ferromagnetic state across the electrical transition therefore suggests that the magnetic state is directly correlated with the localized electrons, rather than the itinerant ones, which then calls for further investigation of the intrinsic mechanism of this magnetic compound beyond the double-exchange mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Material processing, microstructure, and composite properties of low carbon Engineered Cementitious Composites (ECC)

Traditional PVA fiber-reinforced Engineered Cementitious Composites (ECC) show high tensile ductility and superior durability with tight crack width, but the high cost and embodied carbon can hinder its wider application in infrastructures. The objective of this study is to develop a better understanding of the fresh and hardened properties of an ECC that employs a lower embodied-carbon binder, Limestone Calcined Clay Cement (LC3), and lower-cost PP fiber that is widely available. Specifically, the interrelations between material processing, microstructure, and composite properties were studied experimentally. The results showed that ECC with high tensile ductility up to 9% tensile strain and tight crack width with 50 μm at 2% tensile strain can be achieved. It was found that a matrix paste with higher viscosity generally enhanced fiber dispersion uniformity and robustness in tensile strain-hardening. The paste viscosity is increased when OPC is replaced by LC3 and can be tuned with superplasticizer content. Larger maximum flaw size leads to lower first crack strength, beneficial for microcrack initiation and multiple cracking. This study generates fundamental knowledge linking processing-microstructure-performance of PP-LC3-ECC. This class of low embodied carbon ECC with tight crack width is expected to contribute to reducing the carbon footprint of the built environment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Rapid solidified ductile Cu-Al-Mn ribbon and its elastocaloric potential

Abstract Cu-Al-Mn alloys display martensitic transformation over a wide range of temperatures. In addition to low cost, this alloy is known for its low transformation stress with reasonable latent heat favoring elastocaloric applications. However, the ductility of Cu-Al-Mn can be limited owing to ordering and intergranular fracture. Through rapid solidification by melt spinning, we show that Cu-Al-Mn ribbon can be made highly ductile (greater than 8% tensile strain in the as-spun state and 10% tensile strain after heat treatment). The ductility of the melt-spun ribbon is related to the suppression of L2 1 ordering that is characterized through magnetic property measurement. Heat treatment of the ribbon promotes bamboo grain formation, and the latent heat is increased to 6.4 J g −1 . Under tensile conditions, we show that the ribbon exhibited about 4 °C temperature change (4.4 °C on heating and 4.2 °C on cooling from 6.3% strain).

36 MATERIALS SCIENCE↗
NASA NTRS1992

Tensile strain-rate sensitivity of tungsten/niobium composites at 1300 to 1600 K

The tensile behavior of continuous tungsten fiber reinforced niobium composites (W/Nb), fabricated by an arc-spray process, was studied in the 1300 to 1600 K temperature range. The tensile properties of the fiber and matrix components as well as of the composites were measured and were compared to rule of mixtures (ROM) predictions. The deviation from the ROM was found to depend upon the chemistry of the tungsten alloy fibers, with positive deviations for ST300/Nb (i.e., stronger composite strength than the ROM) and negative or zero deviations for 218/Nb.

Yun, H. M.↗
DOE OSTI2022

Straintronic Effect on Phonon-Mediated Superconductivity of Nb 2 CT 2 (T = O, S, Se, or Te) MXenes

Here, the electronic structures, phonon dispersions, and electron–phonon coupling of Nb 2 CT 2 (T = O, S, Se, or Te) MXenes were investigated via first-principles calculations. Different models of Nb 2 CT 2 were constructed, and the results show that the low-energy models of Nb 2 CT 2 are intrinsic phonon-mediated superconductors. Of the four Nb 2 CT 2 MXenes, Nb 2 CO 2 MXene exhibits the largest superconducting critical temperature ($T_c$) of 14.43 K. The existence of soft modes induced by Kohn anomalies and the contribution of Nb atoms to the Fermi level lead to strong electron–phonon coupling (λ = 0.92) in Nb 2 CO 2 MXene. The $T_c$ of Nb 2 CO 2 is further enhanced by biaxial tensile strain and reaches up to 18.28 K under 4% tensile strain. The predicted $T_c$ of Nb 2 CS 2 is 4.5 K, which is comparable with experimental data. These findings will further stimulate the search for superconducting MXenes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Interplay Between Strain and Thickness on the Effective Carrier Lifetime of Buffer-Mediated Epitaxial Germanium Probed by the Photoconductance Decay Technique

We report contactless effective minority carrier lifetime of epitaxially grown unstrained and in-plane <110> biaxially tensile-strained (001) germanium (..epsilon..-Ge) epilayers measured using microwave-reflectance photoconductance decay measurements. Strained Ge epilayers were grown using InxGa1-xAs linearly graded buffers on (001) GaAs substrates. Using homogeneous excitation of unstrained Ge epilayers, thickness-dependent separation of minority carrier lifetime components under low injection conditions yielded a bulk lifetime of 114 +/- 2 ns and low surface recombination velocity of 21.3 +/- 0.04 cm/s. More notably, an effective minority carrier lifetime of >100 ns obtained from sub-50 nm 1.6% tensile-strained Ge epilayers showed no degradation relative to the unstrained counterpart. Detailed material characterization using X-ray diffractometry revealed successful strain transfer of 0.61 and 0.89% to the Ge epilayers via InxGa1-xAs metamorphic buffers and confirms pseudomorphic growth. Lattice coherence observed at the e-Ge epilayer and InxGa1-xAs buffer heterointerfaces via transmission electron microscopy substantiates the prime material quality achieved. The relatively high carrier lifetimes achieved are an indicator of excellent material quality and provide a path forward to realize low-threshold Ge laser sources.

bulk lifetime↗
DOE OSTI2023

Voltage control of magnetism in Fe3-xGeTe2/In2Se3 van der Waals ferromagnetic/ferroelectric heterostructures

Abstract We investigate the voltage control of magnetism in a van der Waals (vdW) heterostructure device consisting of two distinct vdW materials, the ferromagnetic Fe 3- x GeTe 2 and the ferroelectric In 2 Se 3 . It is observed that gate voltages applied to the Fe 3- x GeTe 2 /In 2 Se 3 heterostructure device modulate the magnetic properties of Fe 3- x GeTe 2 with significant decrease in coercive field for both positive and negative voltages. Raman spectroscopy on the heterostructure device shows voltage-dependent increase in the in-plane In 2 Se 3 and Fe 3- x GeTe 2 lattice constants for both voltage polarities. Thus, the voltage-dependent decrease in the Fe 3- x GeTe 2 coercive field, regardless of the gate voltage polarity, can be attributed to the presence of in-plane tensile strain. This is supported by density functional theory calculations showing tensile-strain-induced reduction of the magnetocrystalline anisotropy, which in turn decreases the coercive field. Our results demonstrate an effective method to realize low-power voltage-controlled vdW spintronic devices utilizing the magnetoelectric effect in vdW ferromagnetic/ferroelectric heterostructures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS2008

Design Guidelines for In-Plane Mechanical Properties of SiC Fiber-Reinforced Melt-Infiltrated SiC Composites

In-plane tensile stress-strain, tensile creep, and after-creep retained tensile properties of melt-infiltrated SiC-SiC composites reinforced with different fiber types were evaluated with an emphasis on obtaining simple or first-order microstructural design guidelines for these in-plane mechanical properties. Using the mini-matrix approach to model stress-strain behavior and the results of this study, three basic general design criteria for stress and strain limits are formulated, namely a design stress limit, a design total strain limit, and an after-creep design retained strength limit. It is shown that these criteria can be useful for designing components for high temperature applications.

Morscher, Gregory N.↗
DOE OSTI2022

Strain-Dependent Surface Defect Equilibria of Mixed Ionic-Electronic Conducting Perovskites

We report understanding the surface defect chemistry and its strain dependency is essential in developing next-generation electrochemical devices. However, due to their nanoscale dimensions, surface defects cannot be accessed by conventional techniques used in bulk defect studies. Here, we constructed the strain-dependent surface defect equilibria (i.e., the Brouwer diagram) of mixed ionic-electronic conducting perovskite oxides with near ambient pressure X-ray absorption spectroscopy. Using coherently strained thin-film La 0.6 Sr 0.4 Fe O3 (LSF) as model systems, we probed their surface defect equilibria at 400 °C in oxygen partial pressures between 1 to 10 -5 Torr. We found that the electron holes on the LSF surfaces have strong oxygen character, regardless of the strain states. Nevertheless, tensile strain makes the LSF surface more reducible than the compressed counterpart. These two observations were then validated using first-principles calculations. Finally, with the aid of thermodynamic analyses, we showed that the strain-dependent surface defect equilibria of LSF can be captured by bulk-like ideal solution defect models with shifted oxygen chemical potentials. The findings and methodology presented in this study enable quantitative determination of the surface defect chemistry, which is crucial to understanding and designing functional surfaces for efficient conversions of energy and fuels.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Monolithically Integrated $\varepsilon$-Ge/In x Ga 1-x As Quantum Well Laser Design: Experimental and Theoretical Investigation

Here, we have analyzed the electrical and optical phenomenon occurring in a $\varepsilon$-Ge/In x Ga 1-x -Ge/In x Ga 1-x As quantum well (QW) laser through self-consistent physical solvers calibrated using in-house experimental results. A separate confinement heterostructure QW design is proposed to enable lasing from tensile strained germanium ($\varepsilon$-Ge/In x Ga 1-x -Ge) in the range of 1.55 um to 4 um wavelengths as a function of QW thickness and indium (In) composition. Different recombination mechanisms were analyzed as a function of tensile strain in $\varepsilon$-Ge/In x Ga 1-x -Ge QW. Minority carrier lifetime and band alignment are key attributes of a QW laser, which were measured using microwave photoconductive decay and x-ray photoelectron spectroscopy (as a function of In composition), respectively. The transition point of Ge to a direct bandgap material is re-affirmed to be at $\varepsilon$-Ge/In x Ga 1-x = 1.6% (In ~24%) and the transition from type I to type II for $\varepsilon$-Ge/In x Ga 1-x -Ge/In x Ga 1-x As QW is found to be at In ~55%. Also, the transition to a TM mode dominant laser is identified at In ~15%. Using a tunable waveguide design to optimize confinement as a function of In composition, strain, wavelength, QW thickness, refractive index, and geometry, the $\varepsilon$-Ge/In x Ga 1-x -Ge QW laser design provided a net material gain of ~2000 cm -1 and a threshold current density of ~5 kA/cm 2 , which is an improvement over existing Ge based lasers. In conclusion, the impact of In composition and QW thickness on the band structure, polarized gain spectra, and various lasing metrics were analyzed to show $\varepsilon$-Ge/In x Ga 1-x -Ge/InGaAs QW lasers as promising for integrated photonics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Emergent symmetry in TbTe 3 revealed by ultrafast reflectivity under anisotropic strain

Here, we report ultrafast reflectivity measurements of the dynamics of the order parameter of the charge density wave (CDW) in TbTe 3 under anisotropic strain. We observe an increase in the frequency of the amplitude mode with increasing tensile strain along the a-axis (which drives the lattice into a > c, with a and c the lattice constants), and similar behavior for tensile strain along c (c > a). This suggests that both strains stabilize the corresponding CDW order and further support the near equivalence of the CDW phases oriented in a- and c-axis, in spite of the orthorhombic space group. The results were analyzed within the time-dependent Ginzburg–Landau framework, which agrees well with the reflectivity dynamics. Our study presents an ultrafast approach to assess the stability of phases and order parameter dynamics in strained systems.

Kim, Soyeun↗