Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermal modeling and analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Finite element-finite difference thermal/structural analysis of large space truss structures

A technique of automated and efficient thermal-structural processing of truss structures that interfaces the finite element and finite difference method was developed. The thermal-structural analysis tasks include development of the thermal and structural math models, thermal analysis, development of an interface and data transfer between the models, and finally an evaluation of the thermal stresses and displacements in the structure. Consequently, the objective of the developed technique was to minimize the model development time, in order to assure an automatic transfer of data between the thermal and structural models as well as to minimize the computer resources needed for the analysis itself. The method and techniques described are illustrated on the thermal/structural analysis of the Space Station Freedom main truss.

Warren, Andrew H.↗
NASA NTRS1992

Thermal response of rigid and flexible insulations and reflective coating in an aeroconvective heating environment

Described here is the thermal performance of rigid and flexible thermal protection systems considered for potential use in future Aeroassist Space Transfer Vehicles. The thermal response of these materials subjected to aeroconvective heating from a plasma arc is described. Properties that were measured included the thermal conductivity of both rigid and flexible insulations at various temperatures and pressures and the emissivity of the fabrics used in the flexible insulations. The results from computerized thermal analysis models describing the thermal response of these materials subjected to flight conditions are included.

Kourtides, D. A.↗
NASA NTRS2013

Thermal Modeling and Analysis of the Hurricane Imaging Radiometer (HIRad)

The Hurricane Imaging Radiometer (HIRad) is a payload carried by an unmanned aerial vehicle (UAV) at altitudes up to 60,000 ft with the purpose of measuring ocean surface wind speeds and near ocean surface rain rates in hurricanes. The payload includes several components that must maintain steady temperatures throughout the flight. Minimizing the temperature drift of these components allows for accurate data collection and conclusions to be drawn concerning the behavior of hurricanes. HIRad has flown on several different UAVs over the past two years during the fall hurricane season. Based on the data from the 2011 flight, a Thermal Desktop model was created to simulate the payload and reproduce the temperatures. Using this model, recommendations were made to reduce the temperature drift through the use of heaters controlled by resistance temperature detector (RTD) sensors. The suggestions made were implemented for the 2012 hurricane season and further data was collected. The implementation of the heaters reduced the temperature drift for a portion of the flight, but after a period of time, the temperatures rose. With this new flight data, the thermal model was updated and correlated. Detailed analysis was conducted to determine a more effective way to reduce the temperature drift. The final recommendations made were to adjust the set temperatures of the heaters for 2013 flights and implement hardware changes for flights beyond 2013.

Mauro, Stephanie↗
NASA NTRS1970

A thermal model for analysis of infrared images

A mathematical model derived from the equation of heat conduction was developed to assist in interpreting thermal infrared images acquired from aircraft and spacecraft. The model assumes steady state boundary conditions. It contains parameters of rock and soil properties, atmospheric effects, site location, and season. The results predicted provide an explanation for the thermal differences among granite, limestone, and dolomite recorded in the December 1968 daytime and predawn flights over the Mill Creek, Oklahoma test site, during which representative thermal inertia and albedo values were used. A second test of the model made use of data acquired during the June 1970 predawn overflight of Mill Creek. A simple model of transient heating of the ground was constructed as an extension of the overall model, in order to examine the effects of atmospheric perturbations. The results obtained are consistent with those of ground observations made at the time of the overflight.

Watson, K.↗
NASA NTRS2001

Thermal Modeling and Analysis of a Sub-Compact Seebeck Furnace

The Sub-Compact Seebeck Furnace (SCSF) is a third generation furnace designed as an experimental facility to study the phenomena of undercooling associated with directional solidification. It is intended to provide a double peak temperature profile along the axial direction with gradient zones at each end. By keeping the temperature in the central portion above the melting point of the sample, and cooling the ends of the furnace, a solid/liquid (S/L) interface can be maintained in each one of the gradient zones. A motorized motion control provides a motion to one-half of the furnace. The undercooling associated with the interface being directionally solidified can thus be studied. Modeling of the temperature profile is important to help assure that the furnace design provides the correct thermal characteristics. The furnace is designed with two halves that telescope. Results of thermal analysis based on an analytical solution using simple assumptions will be presented. The resulting temperature profile will show the salient features of the desired thermal profile and provide the general directions for thermal design. Experimental results will be used to compare with the analytical profile. Approach for numerical modeling to provide more detailed information such as two-dimensional effects will be discussed.

Wang, Francis C.↗
NASA NTRS1978

Thermal math model analysis of FRSI test article subjected to cold soak and entry environments

A multi-objective test program was conducted at the NASA/JSC Radiant Heat Test Facility in which an aluminum skin/stringer test panel insulated with FRSI (Flexible Reusable Surface Insulation) was subjected to 24 simulated Space Shuttle Orbiter ascent/entry heating cycles with a cold soak in between in the 10th and 20th cycles. A two-dimensional thermal math model was developed and utilized to predict the thermal performance of the FRSI. Results are presented which indicate that the modeling techniques and property values have been proven adequate in predicting peak structure temperatures and entry thermal responses from both an ambient and cold soak condition of an FRSI covered aluminum structure.

Gallegos, J. J.↗
DOE OSTI2024

Primary System Thermal Fluids Analysis Model Development for the Compact High Temperature Gas Reactor (HC-HTGR) (Final Report)

Horizontal Compact High Temperature Gas Reactor (HC-HTGR) is being designed by a multi-disciplinary team of nuclear, mechanical, and structural engineers under the support of a DOE-NE Advanced Reactor Demonstration Program’s Advanced Reactor Concepts-20 (ARC-20) award. The objective of this ARC-20 project is to deliver a conceptual design for the proposed HC-HTGR and support its commercialization as a safe, low-cost HTGR. Argonne National Laboratory (Argonne) is collaborating on the thermal hydraulic design and analysis of HC-HTGR reactor pressure vessel internals to ensure the reactor maintains sufficient safety margins during normal operation, shutdown, and accident conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1983

Thermal modeling and analysis of structurally complex spacecraft using the IDEAS system

Large antenna satellites of unprecedented sizes are needed for a number of applications. Antenna diameters on the order of 50 meters and upward are required. Such antennas involve the use of large expanses of lattice structures with hundreds or thousands of individual connecting members. In connection with the design of such structures, the consideration of thermal effects represents a crucial factor. Software capabilities have emerged which are coded to include major first order thermal effects and to purposely ignore, in the interest of computational efficiency, the secondary effects. The Interactive Design and Evaluation of Advanced Spacecraft (IDEAS) is one such system. It has been developed for an employment in connection with thermal-structural interaction analyses related to the design of large structurally complex classes of future spacecraft. An IDEAS overview is presented. Attention is given to a typical antenna analysis using IDEAS, the thermal and loading analyses of a tetrahedral truss spacecraft, and ecliptic and polar orbit analyses.

Garrett, L. B.↗
NASA NTRS2019

Thermal Analysis of Potted Litz Wire for High-Power-Density Aerospace Electric Machines

Increasing the power density and efficiency of electric machines (motors and generators) is integral to bringing Electrified Aircraft (EA) to commercial realization. To that end an effort to create a High Efficiency Megawatt Motor (HEMM) with a goal of exceeding 98% efficiency and 1.46 MW of power has been undertaken at the NASA Glenn Research Center. Of the motor components the resistive losses in the stator windings are by far the largest contributor (34%) to total motor loss. The challenge is the linear relationship between resistivity and temperature, making machine operation sensitive to temperature increases. In order to accurately predict the thermal behavior of the stator the thermal conductivity of the Litz wire-potting-electrical insulation system must be known. Unfortunately, this multi material system has a wide range of thermal conductivities (0.1 W/m-K – 400 W/m-K) and a high anisotropy (axial vs transverse) making the prediction of the transverse thermal conductivity an in turn the hot spot temperatures in the windings is difficult. In order to do this a device that simulates the thermal environment found in the HEMM stator was designed. This device is not unlike the motorettes (little motors) that are described in IEEE standards for testing electrical insulation lifetimes or other electric motor testing. However, because the HEMM motor design includes significant rotor electrical and thermal considerations the term motorette was not deemed appropriate. Instead statorette (or little stator) was adopted as the term for this test device. This paper discussed the design, thermal heat conjugate analysis (thermal model), manufacturing and testing of HEMM's statorette. Analysis of the results is done by thermal resistance network model and micro thermal model and is compared to analytical predictions of thermal conductivity of the insulated and potted Litz wire system.

Motor↗
DOE OSTI2020

Thermal Analysis Evaluations Using the Dry Cask Simulator

Different thermal analysis models were developed to simulate the dry cask simulator (DCS). The DCS is an experiment designed to simulate dry storage of a single boiling water reactor fuel assembly under a variety of heat loads and internal pressures. The DCS was set up and tested in both a vertical and horizontal configuration to determine cladding temperatures in vertical and horizontal dry cask storage systems. The models included a detailed STAR-CCM+ model with the fuel assembly geometry explicitly modeled, a porous STAR-CCM+ model with the fuel assembly geometry modeled as porous media region with calculated effective properties, and a COBRA-SFS model. COBRA-SFS is a thermal-hydraulic code developed for steady-state and transient analysis of multi assembly spent-fuel storage and transportation systems. STAR-CCM+ is a commercial computation fluid dynamics (CFD) code. Both a detailed and porous STARCCM+ model were developed to look at the effective thermal conductivity (keff) approach to modeling a fuel assembly. A keff fuel model is typically model in CFD thermal analyses due to its significantly lower computational costs. The models were run for a combination of low and high canister pressures (100 kPa and 800 kPa) and low and high internal heat loads (0.5 kW and 5 kW). Results from all three models were compared against experimental data taken from the DCS for the peak cladding temperature (PCT) and inlet air mass flow.

Suffield, Sarah R.↗
NASA NTRS1998

Thermal Effects Modeling Developed for Smart Structures

Applying smart materials in aeropropulsion systems may improve the performance of aircraft engines through a variety of vibration, noise, and shape-control applications. To facilitate the experimental characterization of these smart structures, researchers have been focusing on developing analytical models to account for the coupled mechanical, electrical, and thermal response of these materials. One focus of current research efforts has been directed toward incorporating a comprehensive thermal analysis modeling capability. Typically, temperature affects the behavior of smart materials by three distinct mechanisms: Induction of thermal strains because of coefficient of thermal expansion mismatch 1. Pyroelectric effects on the piezoelectric elements; 2. Temperature-dependent changes in material properties; and 3. Previous analytical models only investigated the first two thermal effects mechanisms. However, since the material properties of piezoelectric materials generally vary greatly with temperature (see the graph), incorporating temperature-dependent material properties will significantly affect the structural deflections, sensory voltages, and stresses. Thus, the current analytical model captures thermal effects arising from all three mechanisms through thermopiezoelectric constitutive equations. These constitutive equations were incorporated into a layerwise laminate theory with the inherent capability to model both the active and sensory response of smart structures in thermal environments. Corresponding finite element equations were formulated and implemented for both the beam and plate elements to provide a comprehensive thermal effects modeling capability.

Lee, Ho-Jun↗
DOE OSTI2022

Thermal Stress Modeling and Analysis of Packed-bed Thermocline Energy Storage Tank for INL Thermal Energy Distribution System (TEDS)

The Thermal Energy Distribution System (TEDS) at Idaho National Laboratory (INL) is a thermal-hydraulic flow loop to support the integration of co-located multiple experimental systems, where a packed-bed thermal energy storage (TES) is installed as a thermal buffer and storage unit for TEDS. The packed-bed TES is adopted in TEDS because of its benefit as a low-cost single-tank storage option compared to the traditional two-tank storage. However, thermal ratcheting is one potential design concern which is caused by the rearrangement of granular filler inside a packed-bed tank during continuous thermal cycling operation of the packed-bed TES tank. If the thermally induced stress exceeds yield strength of the tank wall, it may cause catastrophic consequences like rupture of the thermal storage tank. Thus, it is crucial to understand the phenomenon to ensure the robust operation. Based on the temperature boundary conditions given by transient thermal analyses with computational fluid dynamics (CFD) simulations, the thermal ratcheting analysis is then conducted to evaluate the hoop stress and resultant thermal ratcheting potential of the TES tanks with two different modeling approaches: (1) infinite rigidity model and (2) Drucker-Prager (DP) model. The validity of each modeling method was examined by comparing the numerical simulation with the experimental data obtained from the packed-bed TES tank for Solar One Plant and evaluate the thermal ratcheting potential of the TEDS TES tank.

25 ENERGY STORAGE↗
NASA NTRS1990

Flight motor set 360L006 (STS-34). Volume 1: System overview

Flight motor set 360L006 was launched at approximately 11:54 a.m. Central Daylight Time (CDT) on 18 October 1989 as part of NASA space shuttle mission STS-34. As with all previous redesigned solid rocket motor launches, overall motor performance was excellent. All ballistic contract end item (CEI) specification parameters were verified with the exceptions of ignition interval and rise rates. Ignition interval and rise rates could not be verified due to the elimination of developmental flight instrumentation from fourth flight and subsequent, but the low sample rate data that were available showed nominal propulsion performance. All ballistic and mass property parameters closely matched the predicted values and were well within the required CEI specification levels that could be assessed, with the exception of the RH-motor vacuum-delivered specific impulse. It exceeds the upper-limit CEI specification due to a bias imposed on the raw data by the OPT/Taber gage measurement differences. Evaluation of the ground environment instrumentation measurements again verified thermal model analysis data and showed agreement with predicted environmental effects. No launch commit criteria thermal violations occurred. Postflight inspection again verified superior performance of the insulation, phenolics, metal parts, and seals. Postflight evaluation indicated both nozzles performed as expected during flight, although splashdown loads tore the left-hand, 45-deg actuator bracket from the nozzle. All combustion gas was contained by insulation in the field and nozzle-to-case joints. Recommendations were made concerning improved thermal modeling and measurements. The rationale for these recommendations, the disposition of all anomalies, and complete result details are contained.

Garecht, Diane M.↗
NASA NTRS1985

A three-dimensional transient thermal analysis of the Lidar Atmospheric Sensing Experiment

The development of a three-dimensional thermal analysis model of the Lidar Atmospheric Sensing Experiment (LASE) is the subject of this paper. The use of an interactive computer graphics and finite element generation program to define the geometry information for the thermal model is discussed. The methods used in calculating the heat transfer parameters are explained. The results of the thermal analysis are given, and these results are compared with actual flight data.

Carlson, A. B.↗
NASA NTRS1990

Flight motor set 360L007 (STS-33R)

Flight motor set 360L007 was launched as part of NASA space shuttle mission STS-33R. As with all previous redesigned solid rocket motor launches, overall motor performance was excellent. There were no debris concerns for either motor. Both motors exhibited unbonds on one factory joint weatherseal. All ballistics contract end item specification parameters were verified, with the exception of ignition interval and rise rates. Ignition interval and rise rates could not be verified due to the elimination of developmental flight instrumentation from fourth flight and subsequent, but the low sample rate data that were available showed nominal propulsion performance. All ballistic and mass property parameters closely matched the predicted values and were well within the required contract end item specification levels that could be assessed. All 108 Ground Environment Instrumentation (GEI) measurements performed properly throughout the prelaunch phase. Evaluation of the GEI measurements again verified thermal model analysis data and showed agreement with predicted environmental effects. No launch commit criteria thermal violations occurred. All joint heaters operated normally, but a high voltage reading was noted on the left hand aft heater, which was immediately determined to be a voltage sensor error and not a heater anomaly due to no current increase. Postflight inspection again verified superior performance of the insulation, phenolics, metal parts, and seals. Postflight evaluation indicated both nozzles performed as expected during flight. All combustion gas was contained by insulation in the field and case-to-nozzle joints.

Garecht, Diane↗