Search NASA⌕ Search

SEARCH · Search NASA

Results for “Thermomechanical Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

High Temperature Mechanical Behavior of Refractory Alloys with Digital Image Correlation

Gas turbine efficiency is typically limited by the maximum allowable temperature for components at the inlet side and in the hot gas flow. Refractory alloys and SiC/SiC ceramic-matrix composites (CMCs) are promising candidates for advancing operating temperatures beyond those of Ni-based alloys (>1200 °C). Refractory alloys are more suitable than SiC/SiC CMCs for dynamic components, due to the latter's low toughness and ductility. However, it is well known that refractory alloys suffer from poor oxidation behavior under service lifetimes and conditions, leading to embrittlement concerns. The ARPA-E ULTIMATE program has set out to combine new alloys with advanced coatings to mitigate oxidation/embrittlement effects, while increasing the mechanical performance benefits of refractory materials. Low oxygen (inert gas) or vacuum systems are needed to assess high temperature mechanical performance of developed alloys. To investigate the environmental sensitivity of candidate alloys and develop high temperature testing capabilities, four argon tensile frames were upgraded as well as a single vacuum system at Oak Ridge National Laboratory. Digital image correlation was incorporated into the vacuum frame allowing for surface strain determination and refined insight into thermomechanical response. Creep testing was performed at 1300 °C on two alloys, C-103 and MHC in vacuum and high purity argon environments. The Mo-based alloy showed less sensitivity to oxygen, indicating that testing in well-controlled argon environments may be suitable. The C-103 alloy demonstrated a stronger sensitivity to oxygen in the well-controlled argon environment, illustrating the need for the developed vacuum testing capabilities. “Small” 25 mm and “large” 76 mm MHC specimens showed comparable results in terms of strain rate during creep testing and ultimate tensile strength during tensile testing, suggesting the viability of smaller geometries that use less material of advanced developmental alloys.

Bell, Sam↗
DOE OSTI2024

Stress relaxation cracking susceptibility evaluation in 347H stainless steel welds

Abstract Stress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.

42 ENGINEERING↗
DOE OSTI2024

A Multiphysics Multiscale Simulation Platform for Damage, Environmental Degradation, and Life Prediction of CMCs in Extreme Environments

This project successfully developed a multiphysics, multiscale computational framework to enhance the design and development of CMCs, with a focus on modeling highly nonlinear, time-dependent damage mechanisms and material degradation under extreme conditions, such as those experienced in turbine service environments. The project made significant advances in improving our understanding of progressive damage, oxidative degradation, and time-dependent inelastic deformation in CMCs, with particular attention to the role of uncertainties in predictions. Key outcomes include the integration of advanced material characterization, uncertainty quantification, and multiphysics constitutive models to predict the behavior of CMCs over their service life. A novel multiscale methodology was employed, which integrated microscale constituent behaviors with structural-scale responses, enabling the manufacturing defects in the microstructure that are prone to damage nucleation. Through the development of DL algorithms, the project advanced the prediction of damage initiation and crack propagation, taking into account the defect morphology and statistical variations across multiple scales. The framework was rigorously validated using thermomechanical experiments, which tested CMCs under various mechanical loadings at elevated temperatures, further enhancing the model's predictive capability. Overall, the research outcomes have provided a more accurate, reliable method for predicting CMC component life, significantly advancing material design, and improving component reliability in extreme environments. This work has strong implications for the optimization of turbine components and other high-performance applications where CMCs are used.

03 NATURAL GAS↗
DOE OSTI2021

Coupling Thermomechanical Processing and Alloy Design to Improve Textures in Mg-Zn-Ca Sheet Alloys

Abstract The effect of Ca and Zn additions on the microstructure and texture evolution during thermomechanical processing of Mg-Zn-Ca sheet alloys was systematically investigated and quantified. Plane strain compression testing in a Gleeble thermomechanical simulator was used to physically simulate a 10-pass rolling schedule, while allowing for careful control and monitoring of the processing parameters. Textures in the as-deformed ternary alloy samples demonstrate a weak maximum basal intensity and spreading in the transverse direction. Increasing the Zn content to 3.2 wt.% in the ternary alloys resulted in samples that exhibited weak textures in the as-deformed state. Importantly, static recrystallization (SRX) during post-deformation annealing of these alloys promoted a desirable annular texture, with the c -axis tipped from the normal direction and a lower basal texture intensity. The evolution in texture during SRX is associated with as-deformed microstructures with broad grain orientation spreads and a low degree of recrystallization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Preliminary Procedures and Acceptance Criteria for in-situ Structural Materials Surveillance for MSR

This report describes the initial development of the technical basis for a materials surveillance technology that, when fully developed and validated, can be used by stakeholders to develop and implement a materials surveillance program to manage materials degradation during reactor operations. The procedures described in this report aim to bound the detrimental effects of the reactor environment on the creep-fatigue life of the reactor components through materials surveillance. Specifically, the report describes procedures for selecting critical locations within the reactor components for surrogate materials surveillance and the sizing and placements of passively-actuated materials surveillance test articles under development by the US Department of Energy, Advanced Reactor Technologies Program. These test articles apply cyclic thermomechanical load to a surrogate sample of the component structural material passively through thermal expansion mismatch within the articles, without requiring any penetrations in the reactor coolant boundary. The procedures can be used to size materials surveillance test articles so that they will fail before the corresponding structural component. These articles would be exposed to the component operating environment, located to experience a bounding radiation fluence and representative coolant exposure. They can be monitored during reactor operations to ensure that they have not failed under the combination of creep-fatigue damage and environmental degradation. The report describes the key technical decisions and the corresponding rational for using these procedures to provide advanced warning of any impending material failure. An appendix describes the technical basis and the procedure for sizing a family of passively-actuated test articles. Finally, the report describes future work needed to complete the technical basis underlying this materials surveillance technology.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Three-Dimensional Heat Flux and Thermal Analysis of Angled Tungsten Samples on DIII-D

ITER-grade tungsten and dispersoid-strengthened tungsten samples with the top surface angled at ~15° towards the incident plasma flux were exposed to 9 H-mode discharges with edge-localized modes (ELMs) in the lower divertor of DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Surface damage included cracking and flaking of material on the two samples farthest away from the plasma strike point, and significant melting of the two samples closest to the strike point. Heat flux and thermal analysis tools new to DIII-D have been applied to better understand this material response and to help optimize the exposure conditions for future experiments. SMITER field-line tracing simulations based on IRTV data and EFIT equilibria estimate an average inter-ELM perpendicular heat flux, 𝑞⊥,𝑖nter−𝐸LM , on the angled surfaces of 10.1 – 19.6 MW/m² for a majority of the 9 discharges, increasing to 15.6 – 24.5 MW/m² for the single, higher-power shot where samples melted. Fast camera data showed shallow intra-ELM melting and re-solidification, which transitioned to bulk inter-ELM melting with melt motion in the 𝐽⃗ 𝑥 𝐵⃗ direction. About 50% of the protruding volume of the most affected sample was displaced via melt-motion. SIERRA thermal modeling software was able to reproduce an onset time of melting consistent with fast camera data and final sample conditions, within < 200 ms. Maximum surface temperatures of 3122 K and 2787 K are estimated for the samples farthest away from the strike point, while the closest samples achieve melting at 4067 ms and 4750 ms into the ~5000 ms plasma exposure. A +10% increase in both the SMITER 𝑞⊥,𝑖nter−𝐸LM calculations and the estimated ELM heat loads 𝑞⊥, 𝐸LM was required to achieve this result, which is within the uncertainty of the diagnostic data but likely accounts for non-ideal geometry effects plus other physics uncertainties not included in this first iteration of modeling. This work provided valuable estimates of the 3D temperature evolution to help better understand the observed surface morphology and internal recrystallization of samples, which are discussed in detail in a complementary manuscript [1]. Benchmarking efforts with more diagnosed DIII-D experiments are underway to further refine the SMITER and SIERRA models for DiMES. Future use of these tools will enable researchers to precisely target heat flux exposure conditions in DIII-D to test, but not exceed, the thermomechanical limitations of novel plasma-facing materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Pursuing small-scale measures of penetration resistance in Ti-5553 alloy

This work was originally proposed to illustrate the performance of a particular set of differently processed Ti-5553 plates under dynamic threats. It became clear that the larger question, at present, is whether the small-scale shaped charge design of an RP-4 detonator can be employed to efficiently explore the dynamic penetration resistance of representative test articles. The initial penetration testing that employed three variants of thermomechanical processing of Ti-5553 plates appeared to demonstrate that there was a noticeable difference in their performance. The remaining pertinent question was regarding the variation in the shaped charge performance and how it compares to the variation from the three titanium plate tests. Based on the limited testing presented here the RP-4 shaped charge detonator appears to have an average depth of penetration in 6061 aluminum of 90mm with a 1.5CD stand off.

shaped charge penetration↗
DOE OSTI2024

Schema Elements for Granta Annual Report: FY2024

Granta: Materials Intelligence (Granta: MI) is a commercial database software distributed by Ansys, Inc. that is utilized by the Nuclear Security Enterprise (NSE) to organize and store relevant materials data. Lack of standard and well-documented database schema is the primary obstacle to an NSE materials data management solution, so the objective of this project is to create and document such a schema. In FY21, an approach for designing, documenting, and managing a standard database schema was described based on the creation of schema elements (collections of attributes used to describe particular aspects of the data) to be used as building blocks for creating various database tables without duplication. In FY22, these methods were applied through a multi-site collaboration to create and document the schema elements necessary to build a thermogravimetric analysis (TGA) testing table. In FY23 the schema was expanded to include elements for a differential scanning calorimetry (DSC) table, along with schema for supporting metadata tables including Instruments, Projects, Documents, and Testing Series. In FY24 the following progress was made, again through multi-site collaboration: • The existing schema elements were modified to accommodate thermomechanical analysis (TMA) data, and a table, Test Data: TMA, was created for managing TMA data. • The elements necessary for the following additive manufacturing (AM) data tables (directed at data specific to selective laser sintering AM technology) were created: • AM Builds • AM Processes • AM Part Designs • Built AM Parts • AM Feedstock Materials • AM Feedstock Material Batches • The elements necessary for creating a Calibrated Material Models table were created, and the Calibrated Material Models table was created. In FY25 the existing schema will be deployed on the production enterprise Granta instance on the enterprise secure network. Schema elements will be appended, and new elements created as necessary, to allow the creation of tables specifically to support materials testing, AM process development, and design and analysis for modernization programs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Summary of FY2024 Experimental Results to Support Development of New Inelastic Material Models and Validation of Section III, Division 5, Class A Design Rules

To address the data gap crucial for updating existing viscoplastic constitutive material models for the Class A materials in the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code, Section III, Division 5, High Temperature Reactors (ASME, 2023) for inelastic design analysis, Oak Ridge National Laboratory (ORNL) conducted experimental studies on Alloy 800H and Alloy 617 across a range of temperatures up to their maximum temperature limits in Section III, Division 5. The studies aim to characterize the materials' deformation behavior under both strain-controlled mechanical cyclic loading and thermal cycling conditions. This report summarizes ORNL's FY 2024 experimental findings on Alloy 800H and Alloy 617, focusing on pure fatigue tests, cyclic stress-strain curves, thermomechanical fatigue experiments, and verification of the high temperature cyclic damage summation design rules.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Irradiation stability and thermomechanical properties of 3D-printed SiC

Neutron irradiation tests were carried out on 3D-printed SiC derived from binderjet additive manufacturing and chemical vapor infiltration. Irradiation was carried to 2.3 dpa over a temperature range of 400–850 °C. Anisotropy that had been observed in the thermal conductivity of 3D-printed SiC prior to irradiation vanished after irradiation as the irradiation defect thermal resistivity accumulated in the material. No degradation in strength was observed in the material before or after irradiation, at various temperatures, or in different orientations. Electron microscopy of the microstructure after neutron irradiation showed distinct defect morphologies in the heterogenous material, but no evidence for irradiation-induced cracking or degradation in the microstructure was observed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Report on partially complete post-irradiation-examination of the INL samples

Ferritic-martensitic steels (NF616 and T91), and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) and their microstructures and mechanical properties were characterized. Ferritic-martensitic steels were irradiated up to 8.16 dpa in the irradiation temperatures ranging from 241 °C to 447.5 °C. Selected 800H and 800H-TMP samples were also irradiated up to 9.12 dpa at 359°C to 431°C. Vickers hardness measurement, fractography, and microstructural characterization were performed on the selected samples in the LAMDA lab. Radiation-induced hardening of NF616 and T91 was observed in the hardness measurements which show ~37% to ~65% increases, depending on irradiation dose and irradiation temperature. Within the irradiation conditions studied in this work, samples with a higher dose had a higher hardness. All the tested alloy 800H and 800H-TMP in this work showed irradiation-hardening by ~96±7% to ~152±10%. Alloy 800HTMP tended to have slightly smaller irradiation-hardening than alloy 800H. The fractography of NF616 samples D2 (2.96 dpa at 291.5°C), D4 (5.91 dpa at 359°C), and D6 (8.16 dpa at 431°C) indicated loss of ductility with negligible necking for the sample D2, yet obvious ductile failure for samples D4 and D6. Fractography of alloy 800H samples N4 (7.27 dpa at 359°C), N5 (3.9 dpa at 451.5°C), and N6 (9.01 dpa at 431°C), and alloy 800H-TMP samples P4 (7.36 dpa at 359°C), P5 (3.95 dpa at 451.5°C), and P6 (9.12 dpa at 431°C) indicated that all samples failed in a ductile mode, with obvious necking. Dimples were observed where large Ti-containing particles were observed for the samples. TEM characterization was performed on alloy 800H (N4, N5, N6) and 800H-TMP (P4, P5 and P6). Accumulation of M23C6 precipitates at grain boundaries was observed in all samples, and the presence of Ti(C,N) precipitates at grain boundaries and in the matrix was observed in alloy 800H-TMP. M23C6 precipitates were found to have the cube-on-cube orientation relationship with the matrix. In addition, nanoscale Si-rich clusters were observed in the matrix of all samples. Atom probe tomography was conducted on the same samples, and their results are being analyzed to be integrated with the TEM results for a confident description of the clustering behavior. Due to the low irradiation temperature (up to 451.5°C), dislocation loops formed in all samples, with the density and the average size of dislocation loops in the order of 1022 – 1023 m-3 and 11.7 – 15.9 nm, respectively. The loop densities in alloy 800H were higher than that in alloy 800H-TMP under the same irradiation conditions. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Time-dependent THMC properties and microstructural evolution of damaged rocks in excavation damage zone

Modeling coupled thermo-hydro-mechanical-chemical (THMC) processes in host rocks near high-level nuclear waste (HLW) repositories at various time scales is an extremely challenging task. The current study integrates experimental, theoretical, and numerical methods in assessing the evolution of excavation damage zone (EDZ) over time and its implication on the long-term migration of hazardous species. Argillite and rock salt and are the focus of this study. The first part of the report presents a novel time-dependent directional microcrack damage theory for generic brittle rocks. It features detailed statistical description of the microcracks within a damaged solid, permitting a direct upscaling of microscale processes such as crack growth kinetics, crack closure/opening, sliding friction to explain the macroscopic creep, nonlinear elasticity, shear dilation, and loading-unloading hysteresis. This provides a basic platform for describing the anisotropic mechanical and transport properties of damaged rocks during excavation and subsequent THMC loadings. The model is validated and numerically implemented to Finite Element (FE) package ABAQUS through the user-defined material (UMAT) interface and have demonstrated great potential in resolving the time-dependent and anisotropic evolution of damage in the EDZ. The second part of the report presents a multi-scale experimental effort in characterizing the thermal, hydraulic, and mechanical properties of Mancos shale and Avery Island salt. For the Mancos shale, triaxial compression tests are performed at different confining pressures and temperatures to probe its thermomechanical properties relevant to HLW repositories. The obtained stress-strain data are interpreted using the proposed directional damage theory. Post-test specimens are subjected to gas permeability tests to reveal the correlation between permeability and the degree of microcracking. At microscale, temperature-controlled nanoindentation tests are performed and found a linear correlation between fracture toughness and elastic modulus from 25°C to 300°C. For Avery Island salt, we have designed and manufactured a novel relative-humidity controlled uniaxial creep device. Long-term creep tests at low stresses (< 5 MPa) are performed at different levels of relative humidity (RH). Besides confirming the much higher creep rates as one would expect through extrapolating the high-stress creep data, the results reveal that the steady-state creep rate of rock salt is strongly dependent on the ambient RH, an aspect that is often neglected in the literature. Both behaviors can be attributed to the pressure-solution creep mechanism which dominates at low stress and high RH levels. The third part of the report explores a set of numerical strategies in modeling the THMC behavior of porous geomaterials. A fully implicit, monolithic FE solution that can flexibly interface with different material models and coupling mechanisms for THMC problems is developed and verified through the ABAQUS user-defined element (UEL) interface. The scheme is used to study the THM response of a hypothetical HLW storage site with reference to an existing in-situ heater test. Strategies for integrating the UEL and the microcrack UMAT are suggested. Another numerical endeavor of this study is to implement a higher-order asymptotic homogenization method to account for the heterogeneous porous structures. The same method is then extended to perform microstructure-informed thermo-mechanical modeling of generalized continua. The above outcomes of this project provide a strong thrust towards enhancing the fundamental understanding and modeling capability of the long-term evolution of host rocks in EDZ, thus helping achieve the design goal of 1-million-year isolation of high-level nuclear wastes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Parallel projection—An improved return mapping algorithm for finite element modeling of shape memory alloys

Here, we present a novel finite element analysis of inelastic structures containing Shape Memory Alloys (SMAs). Phenomenological constitutive models for SMAs lead to material nonlinearities, that require substantial computational effort to resolve. Finite element analysis methods, which rely on Gauss quadrature integration schemes, must solve two sets of coupled differential equations: one at the global level and the other at the local, i.e. Gauss point level. In contrast to the conventional return mapping algorithm, which solves these two sets of coupled differential equations separately using a nested Newton procedure, we propose a scheme to solve the local and global differential equations simultaneously. In the process we also derive closed-form expressions used to update the internal/constitutive state variables, and unify the popular closest-point and cutting plane methods with our formulas. Numerical testing indicates that our method allows for larger thermomechanical loading steps and provides increased computational efficiency, over the standard return mapping algorithm.

42 ENGINEERING↗
DOE OSTI2021

Clarification of creep deformation mechanism in heat-affected zone of 9Cr steels with In Situ experiments

This work quantified nonuniform creep deformation across the heterogeneous heat-affected zone (HAZ) of Grade 91 steel with sophisticated experiments, including an electric-thermal finite element model–assisted Gleeble thermomechanical simulation and a high-temperature creep testing with in situ digital image correlation (DIC). High temperature creep properties of HAZ sub-zones were quantitatively measured by the DIC. Furthermore, by utilizing peak temperature, hardness, local creep strain, and underlying microstructures, creep deformation mechanisms in HAZ were further understood. DIC measurements reveal a creep-vulnerable zone (CVZ) exposed to a peak temperature of 932°C (close to A C3 ) in the intercritical HAZ experienced the fastest creep strength degradation instead of the soft zone with the lowest hardness prior to creep. The significantly reduced precipitation strengthening from misplacement of undissolved and coarsened M 23 C 6 carbides led to a faster recrystallization of tempered martensite in the CVZ. Weak untransformed tempered martensite (ferrite grains) stabilized by local Cr enrichment from dissolved M 23 C 6 also harmed the CVZ's creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Test Plan to Investigate the Optimal Cure Schedule of an Epoxy Resin for Its Application as an Adhesive in Optocouplers

Epoxy resins are polymeric materials that are known for their versatility, low cost, and strong thermal and mechanical properties. They can be used as coatings, adhesives, automotive primers, and have become staples in electronics, aerospace composites and semiconductor encapsulates. Recently, LANL has experienced a decline in the quality of a specialized electronic device, called an optocoupler, which is normally acquired from commercial suppliers. Because of this, a group at LANL is exploring the feasibility of in-house manufacturing of an optocoupler that is better suited for their application. The current prototype has resulted in adhesive failure after being exposed to several thermal cycles. There is a need to investigate the possible reasons for this failure, particularly how the cure schedule of the epoxy might affect its adhesive strength over time and in cycled temperatures. To assist in this investigation, a test plan has been developed involving multiple experiments using thermomechanical analysis (TMA), dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC).

36 MATERIALS SCIENCE↗
DOE OSTI2025

In-Cell Deployment and First Use of Digital Image Correlation for In-Situ Strain Analysis of Irradiated Nuclear Fuel Rods During LOCA Transient

Digital image correlation (DIC) is a noncontact, optical method increasingly used across industries and research environments for acquiring multidimensional strain data. At Oak Ridge National Laboratory’s (ORNL’s) Severe Accident Test Station (SATS), DIC has been extensively applied to study the thermomechanical response of nuclear fuel claddings, yielding fundamental insights into material behavior. However, these efforts have focused exclusively on unirradiated materials and relied on the SATS out-of-cell infrastructure. Efforts over the past two years have been made to extend these capabilities to ORNL’s Irradiated Fuels Examination Laboratory SATS system within the hot-cells to enable testing of irradiated fuel cladding materials. Integrating DIC into the hot-cell SATS infrastructure presents unique challenges, including enabling remote operation of optical equipment and adapting auxiliary hot-cell systems for DIC implementation. This report discusses design, stand-up testing, and application of DIC to an irradiated nuclear fuel cladding segment. A DIC testing rig was successfully built and validated out-of-cell through extensive surrogate tests and calibrations. The rig and specialized DIC furnace were installed in the hot-cell, and a DIC test was successfully conducted. Results from that test correspond to expectations for Zr-based alloys and showed similar uncertainties compared to out-of-cell tests.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

High-temperature superelasticity in NiTiPt and NiTiPd shape memory alloys

Alloying NiTi shape memory alloys with sufficient Pt and Pd at the expense of Ni has been shown to increase transformation temperatures well above those possible with the binary composition, enabling consideration of a new class of high-temperature mechanical sensors and actuators. To achieve shape memory behavior at temperatures greater than 200 °C, previous studies of NiTiPt and NiTiPd compositions have focused primarily on alloys with greater than 16 at.% Pt and 25 at.% Pd. While generally not the focus, none of these previous studies demonstrated superelastic behavior at high temperatures. In an effort to identify alloys that transform to austenite at approximately 200 °C and exhibit superelastic behavior with recoverable strains greater than 2%, a series of Ti-rich NiTiPt ternary alloys with 15.5–16.5 at.% Pt, and Ti-rich NiTiPd ternary alloys with 25–26 at.% Pd have been targeted. The polycrystalline alloys were processed via arc melting followed by homogenization heat treatment. Thermomechanical properties were measured using electro-discharge machined tension test coupons and a miniature load frame equipped with a clamshell furnace. Ultimately, superelasticity in uniaxial tension with clear plateau regions was demonstrated and characterized in these alloys at temperatures between 219 °C and 270 °C.

Massad, Jordan E.↗
DOE OSTI2021

Electrical, structural and thermomechanical properties of doped-LaCrO3 ceramics for high temperature electronics and sensing applications.

Many important electrical and sensor applications require stable conductors under working temperatures up to 1500oC various redox environments. Common high temperature conductors such as nitrides and carbides are not stable under oxidizing atmospheres, for this reason low redox behavior materials would be more attractive. In this work, further dopant studies of the LaCrO3 system were completed in order to control the electronic and ionic conductivity, as well as the relative chemical and microstructural stability. Neodymium and Niobium dopants were initially studied to control the p-type, and potentially n-type conductive mechanisms, respectively, but other dopants strategies were also investigated. The electrical conductivity and Seebeck coefficient were characterized up to 1500oC under varying oxygen partial pressures. The phase and microstructural evolution of each material was also investigated for these compositions by XRD and SEM. The materials showing the best electrical and thermomechanical performance were included within thick films sensors and were tested.

20 FOSSIL-FUELED POWER PLANTS↗