SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Four thermophysical properties of both the solid and the liquid titanium measured using the high-temperature electrostatic levitator at JPL are presented. These properties are the density, the thermal expansion coefficient, the constant pressure heat capacity, and the hemispherical total emissivity.
Molten salts have many applications in the nuclear and solar energy industries for thermal storage and heat transfer applications. However, there is a knowledge gap in molten salt thermophysical properties which hinders the technical readiness level of molten salt applications, especially in the nuclear industry. A common method of investigating new materials is through ab initio Molecular Dynamics (AIMD) simulations which is an effective tool to investigate structural and thermophysical properties at realistic temperatures. NaCl-MgCl 2 is an inexpensive salt that is a good candidate for use as a heat transfer medium in solar power applications or in the secondary loop of a nuclear reactor. In this article, the thermophysical properties of NaCl-MgCl 2 are computed via AIMD calculations to supplement the limited experimental studies in the literature. Here a wide range of compositions and temperatures for the pseudo-binary NaCl-MgCl 2 were used to calculate the density, heat capacity, compressibility, enthalpy of mixing, and volumetric thermal expansion coefficient. AIMD is shown to accurately model the densities of molten NaCl-MgCl 2 as there is good agreement with the available literature. This work observed a transition to a monotonic increase of the density with respect to MgCl 2 composition occurring above 1100 K. The heat capacity values increase uniformly with respect to concentration of MgCl 2 at a rate of 2.85 J/mol-K per 10 mol% of MgCl 2 . Select thermophysical properties are fit to a Redlich-Kister expansion for utilization in multiphysics simulations.
An experimental method for direct measurement of the thermophysical properties of wind tunnel heat transfer models was developed. The technique consists of placing the model under a bank of high intensity, radiant heaters so that the fast opening water cooled shutters, which isolate the heater bank from the model, allow a step-input heat rate to be applied. Measurements of the heat transfer rate coupled with a surface-temperature time history of the same material are sufficient to determine the material thermophysical properties. An infrared thermometer is used to measure model surface temperature and a slug calorimeter provides heat transfer rate information. The output from the infrared thermometer and calorimeter is then fed into an analog-to-digital converter which provides digitized data to a computer. This computer then calculates combined thermophysical properties and a teleprinter prints out all the data. Thus, results are available within 7 minutes of test initiation as opposed to the weeks or months required using prior techniques.
Currently, a knowledge gap exists in the available data and understanding of thermophysical properties relating to fresh fuel salts, especially those containing plutonium. Determination of this data is necessary for the design and construction of test reactors, as well as the licensing of future commercial molten salt reactors. Thermophysical properties such as melting temperature, salt stability, density, and heat capacity were determined on synthesized eutectic NaCl-PuCl3 and a more sodium rich composition containing 25 mol% PuCl3. These measurements document the baseline properties of the salt as a function of temperature for future experiments on irradiated fuel salt which will provide a holistic perspective on the change of thermophysical properties during reactor operations. It was determined that the NaCl-PuCl3 ingot synthesized for this study contained 63.4 mol% NaCl, 36.3 mol% PuCl3, and was 99.7% pure. Upon heating it was shown that the NaCl- PuCl3 eutectic was stable at temperatures of 800°C. The onset of melting occurred at 541°C and the enthalpy of fusion was determined to be 140.7 ± 8.4 J/g. Specific heat capacity measurements showed a slightly decreasing trend with respect to temperature in the liquid phase ranging from 0.67 to 0.57 J/g·K, with an average value of 0.637 ± 0.03 J/g·K (104 ± 5 J/mol·K) between 500 to 720°C. Three independent trials of the molten NaCl-PuCl3 eutectic salt found the density to be ?(T) = 3.8589 – 9.5342·10-4 T(°C), validated between 500 to 800°C. In addition to salt synthesis and experimentally determining thermodynamic properties, Ab Initio molecular dynamic (AIMD) simulations were used to calculate density and heat capacity values.
Containerless processing is an important tool for thermophysical property measurements and materials research. The freedom from a crucible allows processing of liquid materials in a metastable undercooled state, as well as allowing processing of high temperature and highly reactive melts. Electrostatic levitation (ESL) is a containerless method which provides a number of unique advantages, including the decoupling of positioning force from sample heating, the ability to operate in ultra-high vacuum or at moderate gas pressure (approximately 3 atm), and the ability to process non-conducting materials. ESL also has the potential to reduce internal flow velocities below those possible with electromagnetic, acoustic, or aero-acoustic techniques. The ESL facility at NASA's Marshall Space Flight Center (MSFC) is in use for thermophysical property measurements and materials research by a number of different internal and external investigators. The methods for obtaining access to the facility, as well as a summary of current capabilities and some future directions will be discussed. In electrostatic levitation, the acceleration of gravity (or residual acceleration in reduced gravity) is opposed by the action of an applied electric field on a charged sample. This positioning method is applicable to any material which can be electrically charged, whether solid or liquid, conducting, or insulating. Because the position of the sample is unstable, a 3-dimensional active control loop rapidly adjusts the applied field to maintain levitation and minimize motion of the sample. Heating lasers melt the sample, and may be adjusted to maintain specified thermal profiles. Microgravity allows electrostatic levitation to work even more effectively. With the need to cancel less than 1 milli-g, the applied field required is reduced from approximately 10 MV/m to approximately 10 kV/m. Alternatively, a microgravity ESL can position larger samples than is possible on the ground, or it can position samples which maintain their charge poorly. Microgravity also reduces the effects of buoyant convection and sedimentation. In the MSFC ESL, many different classes of experiments and measurements have been demonstrated in collaboration with many investigators. These capabilities include heat capacity measurement, phase diagram determination, and nucleation and growth experiments including nucleation rate, TTT curves, and phase selection. We have demonstrated the capability of triggering recalescence of an undercooled liquid sample without loss of levitation. Currently under development are techniques for measuring the surface tension, viscosity, and density of levitated samples, as well as other thermophysical properties. Expanded levitation capabilities including various gas environments for sample processing, sample rotation control and management of thermal gradients are under development for the MSFC ESL. Containerless processing allows research on materials which may not be processed any other way. Electrostatic levitation extends the range of containerless processing to include many materials and classes of materials which cannot be processed by conventional electromagnetic, acoustic, or aerodynamic levitation techniques.
A FORTRAN V computer program, written for the UNIVAC 1100 series, is used to draw a variety of precision thermophysical property charts on the Calcomp plotter. In addition to the program (GASPLOT), which requires (15 160) sub 10 storages, a thermophysical properties routine needed to produce plots. The program is designed so that any two of the state variables, the derived variables, or the transport variables may be plotted as the ordinate - abscissa pair with as many as five parametric variables. The parameters may be temperature, pressure, density, enthalpy, and entropy. Each parameter may have as many a 49 values, and the range of the variables is limited only by the thermophysical properties routine.
This publication presents a thermophysical property survey on materials that could potentially be used for future spacecraft thermal protection systems (TPS). This includes data that was reported in the 1960's as well as more current information reported through the 1980's. An attempt was made to cite the manufacturers as well as the data source in the bibliography. This volume represents an attempt to provide in a single source a complete set of thermophysical data on a large variety of materials used in spacecraft TPS analysis. The property data is divided into two categories: ablative and reusable. The ablative materials have been compiled into twelve categories that are descriptive of the material composition. An attempt was made to define the Arrhenius equation for each material although this data may not be available for some materials. In a similar manner, char data may not be available for some of the ablative materials. The reusable materials have been divided into three basic categories: thermal protection materials (such as insulators), adhesives, and structural materials.
The additive manufacturing (AM) industry has experienced rapid growth in recent decades as industrial interest in the process has grown. Because of this, there are many groups interested in simulations of the AM process. However, the influence of thermophysical property variability on the melt pool geometry during processing of various AM alloys is unclear. The goal of my work at NASA Langley Research Center (LaRC) was to characterize this influence on Ti-6Al-4V during AM processing alongside developing a tool to enable equivalent studies on other AM materials. To facilitate this process, a database tool was developed to contain and organize thermophysical data previously reported by primary sources. The specific thermophysical properties of interest for this study were density, specific heat capacity, and conductivity. Thermal diffusivity was calculated using the other three properties. This data was then fit with a Gaussian distribution and then randomly sampled from using Monte Carlo random value sampling. Using the Rosenthal equation, this sample data was used to simulate the temperature field during additive manufacturing and extract the melt pool geometry. Specifically, the melt pool’s length, width, and depth. This process was repeated an arbitrary number of times, with the default being 1000. Once this information was obtained, histograms were made showing the distributions of the sizes of the melt pool’s length, width, and depth. Representative statistical metrics of the distributions were calculated (mean, standard deviation, and coefficient of variance). This work found that at the simulated processing values, the melt pool’s width and depth had a 5.7% variation while the length had a 3.2% variation. Additionally, a tool was constructed to graph a thermal color map representation of the melt pool for specific, arbitrary values of density, specific heat, and conductivity. This tool allowed for more efficient plotting of individual queries of the thermophysical properties. The results that were observed in the research were that values reported in literature vary and this variance can have a significant impact on the simulation. Predictions of the melt pool’s dimensions show that length has a standard deviation of approximately 6 μm, width has a standard deviation of approximately 5 μm, and depth can vary by approximately 3 μm. Considering the mean sizes of length, width, and depth are 185 μm, 88 μm, and 44 μm respectively, such a deviation is significant. This shows that depth, for example, could be more than 10% larger or smaller than expected. This demonstrates that variability in the reported thermophysical properties are not negligible and should be expected to have an influence on the results of the laser powder bed fusion additive manufacturing process. When simulating this process in the future, measures should be taken to account for this discrepancy and the uncertainty involved
Six thermophysical properties of both the solid and liquid zirconium measured using the high-temperature electrostatic levitator at JPL are presented.
Thermophysical properties of oxygen at low temperature - bibliography
The objectives of the project are to conduct ground-based experimental and theoretical research on the structural fluctuations and thermophysical properties of molten II-VI compounds to enhance the basic understanding of the existing flight experiments in microgravity materials science programs as well as to study the fundamental heterophase fluctuation phenomena in these melts by: 1) conducting neutron scattering analysis and measuring quantitatively the relevant thermophysical properties of the II-VI melts (such as viscosity, electrical conductivity, thermal diffusivity and density) as well as the relaxation characteristics of these properties to advance the understanding of the structural properties and the relaxation phenomena in these melts and 2) performing theoretical analyses on the melt systems to interpret the experimental results. All the facilities required for the experimental measurements have been procured, installed and tested. It has long been recognized that liquid Te presents a unique case having properties between those of metals and semiconductors. The electrical conductivity for Te melt increases rapidly at melting point, indicating a semiconductor-metal transition. Te melts comprise two features, which are usually considered to be incompatible with each other: covalently bound atoms and metallic-like behavior. Why do Te liquids show metallic behavior? is one of the long-standing issues in liquid metal physics. Since thermophysical properties are very sensitive to the structural variations of a melt, we have conducted extensive thermophysical measurements on Te melt.
In this study, the thermophysical properties of yttrium hydrides were investigated as a function of temperature (room temperature [RT] to 700°C) and hydrogen concentration (H/Y ratio ranges from 1.52 to 1.93). The results indicate that at the temperatures below 300°C, the hydrogen content did not have a significant influence on the thermal expansion, while the specific heat capacity, the thermal diffusivity, and the calculated thermal conductivity were slightly higher for the larger H/Y ratio. Between 300°C and 700°C, a reversible second-order endothermic transition in all measured thermal properties was observed. It was also found that the onset temperatures of the observed transition varied, with the composition having inverse dependence on the hydrogen content. The phase transition from ( α - Y + δ -YH x ) mixed phase to the δ -YH x single phase was excluded from the main contributors to the observed transition. An attempt was made to explain the behavior of the thermophysical properties at higher temperatures by considering the order–disorder transition as a result of hydrogen redistribution.
Ruby laser as energy source for measuring thermophysical properties of materials via flash technique
The apparatus and technique for measuring the thermophysical properties of models used with the phase-change paint method for obtaining wind tunnel heat transfer data are described. The method allows rapid measurement of the combined properties in a transient manner similar to an actual wind tunnel test. An effective value of the thermophysical properties can be determined which accounts for changes in thermal properties with temperature or with depth into the model surface. The apparatus was successfully tested at various heating rates between 19,000 and 124,000 watts per square meter.
Next-generation concentrating solar power (CSP) technology requires high-temperature heat-transfer fluids and thermal energy storage that can operate in the temperature range of 500°–720°C. This high temperature demands a new chemistry for the heat-transfer fluids that must have high-temperature thermal and chemical stabilities, high energy density, and low corrosion rate on metallic materials used in the heat exchangers, piping, and thermal energy storage tanks. A ternary MgCl 2 -KCl-NaCl chloride-salt system has been proposed to achieve such goals, given its high-temperature thermal stability. The chloride-salt-based systems have been used by the metallurgy industry as the electrolyte to electrolytically extract metallic magnesium. They have also attracted attentions from the nuclear industry for developing the molten salt fast reactors that can operate at close to atmospheric pressure and at higher temperature than traditional light-water reactors. However, the corrosion properties of the ternary salt are not well known. The corrosion mechanism is believed to be correlated to the presence of MgOHCl impurity at the operation temperature. MgOHCl is fundamentally caused by the hygroscopic nature of the MgCl 2 component. Therefore, the first key objective of this project is to understand the nature of the corrosiveness of the ternary chloride-salt system and its prevention by designing new lab-scale purification processes. Because of its importance, a working group called the Chloride Salt Collective across multiple U.S. Department of Energy national laboratories is established to gain experimental agreement on the corrosion behaviors. In addition, water generation during salt dehydration could lead to highly corrosive HCl/water mixture via a hydrolysis process between water and anhydrous MgCl 2 or MgCl 2 hydrates. MgOHCl will eventually be converted to MgO particulates regardless of the chemical path chosen (i.e., by thermal decomposition, chemical purification with an active metal, or electrochemical purification utilizing the reduction power of electron flows). Large MgO particles with high hardness can wear out bearing and bushing and even clog the delicate channels in the primary heat exchanger. Because of this, a second objective is to understand the chemistry behind salt purification and transfer the scientific understanding to a set of engineering know-how for large-scale salt melter design. Because there is limited information on the thermophysical properties and the sensitivity of these properties around the targeted salt composition, a third objective is to measure thermophysical properties relevant to system and component design and support Topic 1 Liquid Pathway development. For example, composition shift due to salt reaction with water can be a potential issue because it can lead to changes of thermophysical properties, such as (1) melting point (or freeze point), which can jeopardize safe operation of the supercritical CO 2 power cycle proposed for next-generation CSP, and (2) heat capacity and density, which can decrease the overall power-generation capability of the plants. The value of the thermal conductivity of the selected salt composition is also a critical criterion for the solar receiver design.
LiF–NaF–ZrF 4 multicomponent molten salts are identified as promising candidates for coolant salts in molten salt reactors and advanced high-temperature reactors. This study focused on low-melting point salt compositions of interest: 38LiF–51NaF–11ZrF 4 , 42LiF–29NaF–29ZrF 4 , and 26LiF–37NaF–37ZrF 4 . Ab-initio molecular dynamics (AIMD) calculations were performed and compared with available experimental data to assess the ability of rigid ion models (RIM) to reproduce short- to intermediate-range structure, transport, and thermophysical properties of the LiF–NaF–ZrF 4 salt mixtures. It is found that as ZrF 4 mol% increases, the average cation–anion coordination number (CN) of monovalent cations (Li + , Na + ) obtained from RIM calculations decreases, while multivalent Zr 4+ CN varied from 15% to 19% in comparison to corresponding AIMD values. In addition, RIM is found to predict the existence of 7, 8, and 9 coordinated fluorozirconate complexes, while AIMD and the available experimental data showed an occurrence of 6, 7, and 8 coordinated complexes in the melt. The intermediate-range structure analysis revealed that while the RIM parameters are able to reproduce a local structure for lower ZrF 4 mol% salts such as in 38LiF–51NaF–11ZrF 4 , an extensive fluorozirconate network formation is observed in RIM simulations for higher ZrF 4 mol% compositions. The network generated by RIM parameters is found to be mainly connected by “corner-sharing” fluorozirconate complexes as opposed to both “edge-sharing” and “corner-sharing” connectively portrayed by AIMD. It is found that a close agreement between AIMD and the RIM salt structure for the 11-mol% ZrF 4 salt resulted in good agreement in the calculated Zr diffusivities and the viscosity values. However, due to the inaccurate short- to intermediate-range structure prediction by RIM for higher ZrF 4 mol% compositions, thermophysical properties such as densities and heat capacity differ by up to 26% and 27%, respectively, upon comparison with AIMD and experimental values. Also, the network-dominated properties such as diffusion coefficients and viscosities differed by up to two and three orders of magnitude, respectively. This study signifies the importance of accurate salt structure generation for an accurate prediction of transport and thermophysical properties of multicomponent molten salts.
Fluoride salts are prospective materials for applications in some next-generation nuclear reactors and their thermophysical properties at various conditions are of interest. Experimental measurement of the properties of these salts is often difficult and, in some cases, unfeasible due to challenges from high temperatures, impurity control, and corrosivity. Therefore, accurate theoretical methods are needed for fluoride salt property prediction. In this work, we used moment tensor potentials (MTP) to approximate the potential energy surface of eutectic FLiBe (66.6% LiF – 33.3% BeF2) predicted by the ab initio (DFT-D3) method. Here, we then used the developed potential and molecular dynamics to obtain several thermophysical properties of FLiBe, including radial distribution functions, density, self-diffusion coefficients, thermal expansion, specific heat capacity, bulk modulus, viscosity, and thermal conductivity. Our results show that the MTP potential approximates the potential energy surface accurately and the overall approach yields very good agreement with experimental values. The converged fitting can be obtained with less than 600 configurations generated from DFT calculations, which data can be generated in just 1200 core hours on today's typical processors. The MTP potential is faster than many machine learning potentials and about one order of magnitude slower than widely used empirical molten salt potentials such as Tosi/Fumi.
Specific examples are cited to illustrate the universal needs and demands for thermophysical property data. Applications of the principle of similarity in fluid mechanics and heat transfer and extensions of the principle to fluid mixtures are discussed. It becomes quite clear that no matter how eloquent theories (or experiments) in fluid mechanics or heat transfer are, results of their application can be no more accurate than the thermophysical properties required to transform these theories into practice - or in the case of an experiment, to reduce the data. Present day projects take place on such a scale that the need for international standards groups and mutual cooperation is evident.