SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Thin film batteries employing sputtered LiCoPO4 cathode layers, LiPON electrolyte and Li anode films have been successfully fabricated and tested.
Thin film personal communication system for Apollo astronaut use during extravehicular assignments
Thin film capacitor research and development - deposition of materials for capacitor dielectrics, and materials compatibility with integrated circuits
Magnetic thin films with strong magnetoelastic coupling and low Gilbert damping are key materials for many magnetoelectric devices. Here, we investigated the effects of boron doping concentration on magnetostriction and temperature dependent Gilbert damping in magnetron sputtered (Fe 80 Ga 20 ) 1−𝑥 B 𝑥 films. A crystalline to amorphous structural transition was observed for a boron content near 8% and coincided with a decrease in coercivity from 76 Oe to 3 Oe. A 10% doping concentration is optimal for achieving both large magnetostriction of 48.8 ppm and low Gilbert damping of 6×10 −3 . The temperature dependence of the damping shows an increase at low temperatures with a peak around 40 K, and we associate the relative increase Δ𝛼/𝛼 RT with magnetoelastic contributions to the damping, which has a maximum of 55.7% at 8% boron. An increase in the inhomogeneous linewidth broadening was observed in the structural transition regime at about 8% boron concentration. Furthermore, this study suggests that incorporation of glass forming elements, in this case boron, into Fe 80 Ga 20 is a practical pathway for simultaneously achieving enhanced magnetoelastic coupling and reduced Gilbert damping.
We dope CdTe solar cells with Bi after the device structure is completed using a solution process.
Refractory thin films of Al2O3, ZrO2, MgO, ThO2, and BN have been investigated in situ in an UHV transmission electron microscope. The electron transparent refractory films were prepared by electron-beam evaporation, anodization, RF sputtering, and thinning of bulk crystal materials. The study concentrates on monitoring the thermal and mechanical stability of the films, phase and structural changes, and electron irradiation effects as a function of film-preparation conditions. With increasing temperatures, five different crystallographic phases were observed for both anodized and electron-beam-evaporated alumina films. Zirconia films exhibited two phase transitions upon heating to 1200 C and electron-irradiation-induced crystallization of ZrO2 even at room temperature. MgO, ThO2, and BN films did not undergo any noticeable phase transformation but ruptured due to sintering below 1200 C.
Superconduction thin films, and properties and applications of Josephson effect at radio frequencies
NbN thin film production by refined reactive sputtering technique, discussing Pauli spin paramagnetism and spin orbit scattering in high field superconductivity
BiSrCaCuO thin films were deposited on MgO (100) single-crystal substrates by metalorganic chemical vapor deposition at 500 C and 2 torr using fluorinated beta-diketonate complexes of Sr, Ca, and Cu and triphenylbismuth. An inverted vertical reaction chamber allowed uniform film growth over large areas (7.7 cm diameter). The as-deposited films were amorphous mixtures of oxides and fluorides; a two-step annealing protocol (750 C + 850-870 C) was developed which gives c-axis oriented films of Bi2Sr2Ca1Cu2O(x). The postannealed films showed onsets in the resistive transition of 110 K, and zero resistivity was achieved by 83 K. Critical current densities as high as 11,000 A/sq cm were obtained at 25 K.
A compositionally tunable series of AuCu films is active for electrocatalytic urea generation from carbon dioxide and nitrate.
Passivation films for thin film batteries have been prepared and the conductivity and voltage stability window have been measured. Thin films of Li2CO3 have a large voltage stability window of 4.8V, which facilitates the use of this film as a passivation at both the lithium anode-electrolyte interface at high cathodic potentials.
Thin-film solar cells on flexible, lightweight, space-qualified substrates provide an attractive approach to fabricating solar arrays with high mass-specific power. A polycrystalline chalcopyrite absorber layer is among the new generation of photovoltaic device technologies for thin film solar cells. At NASA Glenn Research Center we have focused on the development of new single-source precursors (SSPs) for deposition of semiconducting chalcopyrite materials onto lightweight, flexible substrates. We describe the syntheses and thermal modulation of SSPs via molecular engineering. Copper indium disulfide and related thin-film materials were deposited via aerosol-assisted chemical vapor deposition using SSPs. Processing and post-processing parameters were varied in order to modify morphology, stoichiometry, crystallography, electrical properties, and optical properties to optimize device quality. Growth at atmospheric pressure in a horizontal hotwall reactor at 395 C yielded the best device films. Placing the susceptor closer to the evaporation zone and flowing a more precursor-rich carrier gas through the reactor yielded shinier-, smoother-, and denser-looking films. Growth of (112)-oriented films yielded more Cu-rich films with fewer secondary phases than growth of (204)/(220)-oriented films. Post-deposition sulfur-vapor annealing enhanced stoichiometry and crystallinity of the films. Photoluminescence studies revealed four major emission bands and a broad band associated with deep defects. The highest device efficiency for an aerosol-assisted chemical vapor deposited cell was one percent.
Thin film surface temperature sensors were developed. The sensors were made of platinum-platinum/10 percent rhodium thermocouples with associated thin film-to-lead wire connections and sputtered on aluminum oxide coated simulated turbine blades for testing. Tests included exposure to vibration, low velocity hydrocarbon hot gas flow to 1250 K, and furnace calibrations. Thermal electromotive force was typically two percent below standard type S thermocouples. Mean time to failure was 42 hours at a hot gas flow temperature of 1250 K and an average of 15 cycles to room temperature. Failures were mainly due to separation of the platinum thin film from the aluminum oxide surface. Several techniques to improve the adhesion of the platinum are discussed.
Thin films of high temperature garnet materials such as yttrium aluminum garnet (YAG) doped with rare earths are currently being investigated as selective emitters. This paper presents a radiative transfer analysis of the thin film emitter. From this analysis the emitter efficiency and power density are calculated. Results based on measured extinction coefficients for erbium-YAG and holmium-YAG are presented. These results indicated that emitter efficiencies of 50 percent and power densities of several watts/sq cm are attainable at moderate temperatures (less than 1750 K).
A thin-film high-Tc superconducting multielement optical detector made of Y-Ba-Cu-O has been designed and evaluated using optical pulses from a diode laser (830 nm) and a Q-switched CO2-laser (10.6 microns). Different thin films have been tested. A laser deposited film showed the strongest response amplitude for short pulses and responded to an ultrafast, 50 ps wide pulse. Comparisons between dR/dT and response as a function of temperature indicated, however, a bolometric response.
The thin-film impact plasma detector was pioneered by Berg for detecting small cosmic dust particles and measuring their approximate velocities in a time-of-flight configuration. While Berg's device was highly successful in establishing the flux of interplanetary dust, the accuracy of measuring the velocities of individual particles was a moderate 18 percent in magnitude and 27 degrees in angle. A much greater accuracy of less than or equal to 1 percent in determining the velocity components appears desirable in order to associate a particle with its parent body. In order to meet that need, research was initiated to determine if a thin-film detector can be designed to provide such accurate velocity measurements. Previous laboratory investigations of the impact plasma uncovered two difficulties: (1) solid or liquid spray is ejected from a primary impact crater and strikes neighboring walls where it produces secondary impact craters and plasma clouds; as a result, both quantity and time of detection of the plasma can vary significantly with the experiment configuration. Particles from an accelerator rarely have speeds v greater than or equal to 10-15 km/s, while cosmic dust particles typically impact at v = 10-72 km/s. The purpose of the tests discussed in this paper was to resolve the two difficulties mentioned. That is, the experiment configuration was designed to reduce the contribution of plasma from secondary impacts. In addition, most particles with v less than or equal to 25 km/s and all particles with v less than or equal to 10 km/s were eliminated from the beam.
A ceramic composite thin film or layer includes individual graphene oxide and/or electrically conductive graphene sheets dispersed in a ceramic (e.g. silica) matrix. The thin film or layer can be electrically conductive film or layer depending the amount of graphene sheets present. The composite films or layers are transparent, chemically inert and compatible with both glass and hydrophilic SiOx/silicon substrates. The composite film or layer can be produced by making a suspension of graphene oxide sheet fragments, introducing a silica-precursor or silica to the suspension to form a sol, depositing the sol on a substrate as thin film or layer, at least partially reducing the graphene oxide sheets to conductive graphene sheets, and thermally consolidating the thin film or layer to form a silica matrix in which the graphene oxide and/or graphene sheets are dispersed.