Search NASA⌕ Search

SEARCH · Search NASA

Results for “Time Reversal Technique”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Reversion phenomena of Cu-Cr alloys

Cu-Cr alloys which were given various aging and reversion treatments were investigated in terms of electrical resistivity and hardness. Transmission electron microscopy was one technique employed. Some results obtained are as follows: the increment of electrical resistivity after the reversion at a constant temperature decreases as the aging temperature rises. In a constant aging condition, the increment of electrical resistivity after the reversion increases, and the time required for a maximum reversion becomes shorter as the reversion temperature rises. The reversion phenomena can be repeated, but its amount decreases rapidly by repetition. At first, the amount of reversion increases with aging time and reaches its maximum, and then tends to decrease again. Hardness changes by the reversion are very small, but the hardness tends to soften slightly. Any changes in transmission electron micrographs by the reversion treatment cannot be detected.

Nishikawa, S.↗
NASA NTRS1972

A real time spectrum to dose conversion system

A system has been developed which permits the determination of dose in real time or near real time directly from the pulse-height output of a radiation spectrometer. The technique involves the use of the resolution matrix of a spectrometer, the radiation energy-to-dose conversion function, and the geometrical factors, although the order of matrix operations is reversed. The new technique yields a result which is mathematically identical to the standard method while requiring no matrix manipulations or resolution matrix storage in the remote computer. It utilizes only a single function for each type dose required and each geometric factor involved.

Farmer, B. J.↗
NASA NTRS1986

The near-earth cross-tail current sheet - Detailed ISEE 1 and 2 case studies

Three near geomagnetic tail current sheet crossings of the ISEE 1 and 2 satellites, on April 5, 1979, are examined in detail. All are assoicated with the passage of an interplanetary shock and the region of variable solar wind pressure behind it. The general geometry of field reversing current sheets is discussed, and this geometry is examined for the cases studied, by using the ISEE 1 and 2 coorbiting satellite data sets. A new technique is employed which removes the effects of a variable sheet normal velocity for the first time. This allows us to calculate firm upper bounds on the current sheet thicknesses, and by utilizing certain physically motivated assumptions, determine the most probable actual sheet thicknesses, and inclinations of the field lines within these sheets. Current density profiles derived with this technique show the main cross-tail current sheet to be a structure that is many thermal ion-gyroradii thick and which is sometimes imbedded in a region that is three or more times thicker and contains much smaller current densities. These profiles also exhibit a considerable amount of fine structure in the sheet which appears as narrow peaks in the current density distributions. Possible explanations for these structures, and for the overall sheet structure itself, are examined.

Mccomas, D. J.↗
NASA NTRS1978

Observation of gravity waves during the extreme tornado outbreak of 3 April 1974

A continuous wave-spectrum high-frequency radiowave Doppler sounder array was used to observe upper-atmospheric disturbances during an extreme tornado outbreak. The observations indicated that gravity waves with two harmonic wave periods were detected at the F-region ionospheric height. Using a group ray path computational technique, the observed gravity waves were traced in order to locate potential sources. The signals were apparently excited 1-3 hours before tornado touchdown. Reverse ray tracing indicated that the wave source was located at the aurora zone with a Kp index of 6 at the time of wave excitation. The summation of the 24-hour Kp index for the day was 36. The results agree with existing theories (Testud, 1970; Titheridge, 1971; Kato, 1976) for the excitation of large-scale traveling ionospheric disturbances associated with geomagnetic activity in the aurora zone.

Hung, R. J.↗
NASA NTRS1985

Quality assurance procedures for V378A matrix resin

A characterization methodology has been developed on which to base quality assurance procedures for U.S. Polymeric V378A bismaleimide matrix resin. Chemical composition is established by partition reverse phase and size exclusion liquid chromatography. Cure rheology behavior is quantitatively characterized by dynamic viscoelastic analysis using the parallel plate technique. The overall cure process is characterized by differential scanning calorimetry. The sensitivity of the procedures is evaluated by studying the effects of ambient out time on the chemical end behaviorial properties of the resin.

Hamermesh, C. L.↗
NASA NTRS2017

Reliability Issues with PME and BME Ceramic Capacitors

Exposure of chip MnO2 tantalum capacitors to humid environments might result in increased ESR, leakage currents, and first turn-on failures. However, there is a lack of literature data on the effect of moisture on reverse bias behavior of the parts. The presence of moisture can also result in pop-corning when a high water vapor pressure develops when moisture absorbed in pores of tantalum slugs vaporizes instantly during soldering process resulting in damage to capacitors. A study of kinetics of moisture ingress to and release from active elements of capacitors would allow a better understanding of degradation mechanisms and is important for preventing failures. In this work, a technique for investigation of moisture sorption and desorption in solid chip tantalum capacitors that employs tantalum slugs as a humidity sensor have been developed and kinetics of the process analyzed for different types of capacitors at temperatures from room to 125 C. A model that relates diffusion characteristics of polymer cases and size of the slugs to characteristic times of moisture sorption has been developed. A strong effect of moisture on long-term degradation of reverse bias currents in MnO2 cathode capacitors has been demonstrated and physical mechanisms discussed.

degradation↗
NASA NTRS2017

Kinetics of Moisture Sorption and Reverse Bias Degradation in Chip Tantalum Capacitors

Exposure of chip MnO2 tantalum capacitors to humid environments might result in increased ESR, leakage currents, and first turn-on failures. However, there is a lack of literature data on the effect of moisture on reverse bias behavior of the parts. The presence of moisture can also result in pop-corning when a high water vapor pressure develops when moisture absorbed in pores of tantalum slugs vaporizes instantly during soldering process resulting in damage to capacitors. A study of kinetics of moisture ingress to and release from active elements of capacitors would allow a better understanding of degradation mechanisms and is important for preventing failures. In this work, a technique for investigation of moisture sorption and desorption in solid chip tantalum capacitors that employs tantalum slugs as a humidity sensor have been developed and kinetics of the process analyzed for different types of capacitors at temperatures from room to 125 ºC. A model that relates diffusion characteristics of polymer cases and size of the slugs to characteristic times of moisture sorption has been developed. A strong effect of moisture on long-term degradation of reverse bias currents in MnO2 cathode capacitors has been demonstrated and physical mechanisms discussed.

Teverovsky, Alexander↗
NASA NTRS2017

Kinetics of Moisture Sorption and Reverse Bias Degradation in Chip Tantalum Capacitors

Exposure of chip MnO2 tantalum capacitors to humid environments might result in increased ESR, leakage currents, and first turn-on failures. However, there is a lack of literature data on the effect of moisture on reverse bias behavior of the parts. The presence of moisture can also result in pop-corning when a high water vapor pressure develops when moisture absorbed in pores of tantalum slugs vaporizes instantly during soldering process resulting in damage to capacitors. A study of kinetics of moisture ingress to and release from active elements of capacitors would allow a better understanding of degradation mechanisms and is important for preventing failures. In this work, a technique for investigation of moisture sorption and desorption in solid chip tantalum capacitors that employs tantalum slugs as a humidity sensor have been developed and kinetics of the process analyzed for different types of capacitors at temperatures from room to 125 C. A model that relates diffusion characteristics of polymer cases and size of the slugs to characteristic times of moisture sorption has been developed. A strong effect of moisture on long-term degradation of reverse bias currents in MnO2 cathode capacitors has been demonstrated and physical mechanisms discussed.

Teverovsky, Alexander↗
NASA NTRS1961

Proceedings of Meeting on Problems and Techniques Associated with the Decontamination and Sterilization of Spacecraft

The United States is about to embark on an ambitious program of Lunar and Space Exploration. This program will not only serve the needs of the national and international scientific community but will also enhance the prestige of the United States in the eyes of the peoples of the world.There are many problems associated with such pioneering investigations, among which is included the effecting of adequate safe- guards against biological contamination of celestial bodies with ter- restrial microorganisms. In the not too distant future, the reverse problem of preventing contamination of our terrestrial body with extraterrestrial microorganisms must be considered. In order to determine the current status of decontamination and sterilization procedures and to arrive at areas of research required in order to increase the knowledge in this field, the NASA sponsored a meeting at which time this problem was discussed. Invitations to attend this meeting were extended to agencies actively concerned with the development of spacecraft and launch vehicles as well as those groups involved in the investigation and development of decontamination and sterilization techniques. The meeting was held in Washington, D, C. on June 29, 1960. The recorded minutes of this meeting, which have been edited, are included in this paper, as well as a listing of recommendations resulting from the deliberations.

Posner, Jack↗
NASA NTRS1976

Fatigue crack growth at elevated temperature 316 stainless steel and H-13 steel

Crack growths were measured at elevated temperatures under four types of loading: pp, pc, cp, and cc. In H-13 steel, all these four types of loading gave nearly the same crack growth rates, and the length of hold time had negligible effects. In AISI 316 stainless steel, the hold time effects on crack growth rate were negligible if the loading was tension-tension type; however, these effects were significant in reversed bending load, and the crack growth rates under these four types of loading varied considerably. Both tensile and compressive hold times caused increased crack growth rate, but the compressive hold period was more deleterious than the tensile one. Metallographic examination showed that all the crack paths under different types of loading were largely transgranular for both CTS tension-tension specimens and SEN reversed cantilever bending specimens. In addition, an electric potential technique was used to monitor crack growth at elevated temperature.

Chen, W. C.↗
NASA NTRS1987

The complex cross-spectra of Cygnus X-2 and GX 5-1

The intensity variations of Cyg X-2 and GX 5-1 are analyzed with a Fourier cross-spectral technique making it possible to measure the frequency dependence of the time lags between the intensity variations in two X-ray spectral bands. In the 20-40 Hz frequency range of the quasi-periodic oscillations (QPO), the hard (about 5-18 keV) signal lags the soft (about 1-5 keV) one, while the reverse is true for the associated red noise. The observed time lags range from 0.4 to 8 ms. For similar QPO parameters, the observed lags are much smaller in GX 5-1 than they are in Cyg X-2. The 'hard lags' previously measured in the cross-correlation functions of these sources are now identified as due to lags in the QPO. It is argued that the 'soft lags' now detected in the red noise are not inconsistent with the interpretation of the hard lags as due to inverse Compton scattering.

Van Der Klis, M.↗
NASA NTRS2013

Thermal Control Using Liquid-Metal Bridge Switches

A short term effort (3-months) was undertaken to demonstrate the feasibility of a novel method to locally control the heat transfer rate and demonstrate the potential to achieve a turndown ratio of approximately 10:1. The technology had to be demonstrated to be at a TRL of 2-3, with a plan to advance it to a TRL 5-6. Here, we show that the concept recently developed in our laboratory, namely the pinned-contact, double droplet switch made by overfilling a hole drilled in a suitable substrate can be implemented with a low-melting temperature metal. When toggled near a second substrate, a liquid bridge can be reversibly connected or disconnected, on demand. We have shown experimentally that liquid-metal bridge switches can be made from gallium with a suitable choice of substrate materials, activation strategies, and control techniques. Individual as well as arrays of gallium bridge switches were shown to be feasible and can be robustly controlled. The very short response time of the bridge connection and disconnection (on the order of 1 millisecond) provides for utility in a wide range of applications. The liquid bridge switches may be controlled actively or passively. We have shown through computations and analysis that liquid bridge switches provide locally large turndown ratios (on the order of 103:1), so a relatively sparse packing of them would be needed to obtain the desired turndown ratio of 10:1. For the laboratory demonstrations, pressure activation was utilized. Simple designs for a passive control strategy are presented which are highly attractive for several reasons, including i) large turndown ratio, ii) no solid-moving parts, and iii) stable operation. Finally, we note that passive systems do not require any electronics for their control. This along with the relatively small molecular weight of candidate materials for the system, makes for a robust design outside of Earth?s magnetic field, where spacecraft are subject to significant radiation bombardment.

Hirsa, Amir H.↗
NASA NTRS1982

Accelerating rate calorimetry: A new technique for safety studies in lithium systems

The role of exothermic reactions in battery test modes is discussed. The exothermic reactions are characterized with respect to their time-temperature and time-pressure behavior. Reactions occuring for any major exotherm were examined. The accelerating rate calorimetry methods was developed to study lithium cells susceptibility to thermal runaway reactions following certain abuse modes such as forced discharge into reversal and charging.

Ebner, W. B.↗
NASA NTRS1997

Reduced Navier Stokes Relaxation Procedures for Internal Flows

In spite of significant advancement in the field of high speed computing, flow calculations involving complex geometries and/or flow behavior still require large amounts of CPU time and memory. In order to predict such flows without sacrificing grid convergence and accuracy, adaptive gridding techniques that provide optimal resolution are highly desirable. The present work combines multigrid techniques and domain decomposition concepts to provide local, solution adaptive, grid refinement. Several viscous compressible and incompressible, two and three-dimensional, flows with strong inviscid interaction and/or axial flow reversal, are considered with a segmented multigrid domain decomposition (SMGDD) procedure for which uniform meshes result in each domain. A pressure-based form of flux-vector splitting is applied to the Navier-Stokes equations, which are represented by an implicit lowest-order reduced Navier-Stokes (RNS) system and a purely diffusive, higher-order, deferred-corrector. A trapezoidal or box-like form of discretization insures that all mass conservation properties are satisfied at interfacial and outflow boundaries, even for this primitive-variable non-staggered grid computation. The SMGDD technique presented herein has previously been applied for incompressible two dimensional flows. The present work offers improvement in the gridding strategy, by allowing for disjoint subdomains that provide optimal resolution of disparate flow features. It also extends the SMGDD technique to three dimensional compressible flows. Laminar and turbulent flow in a backward facing step channel is considered; although the procedure is applicable to more severe geometries. The standard K-epsilon model is applied for turbulence closure. For Re greater than 400, differences between two-dimensional theory and experiment are resolved through a three dimensional simulation, which confirms the experimentally observed three dimensionality of the recirculation patterns on the upper and lower surfaces.

Rubin, Stanley G.↗
NASA NTRS1986

Prediction of blade stresses due to gust loading

An analysis is developed for investigating the response of a rotor-fuselage system in a three-dimensional gust field wherein the gust velocity conponents can have arbitrary variation in space and time. Each rotor blade undergoes flap bending, lag bending and torsional deflections. The blades are divided into beam elements and each element consists of fifteen nodal degrees of freedom. Quasi-steady strip theory is used to obtain the aerodynamic loads. Unsteady aerodynamic effects are introduced through dynamic inflow modeling. Dynamic stall and reverse flow effects are also included. The fuselage is allowed five degrees of freedom: vertical, longitudinal, lateral, pitch and roll motions. The gust response equations are linearized about the vehicle trim state and the blade steady-state deflected position, and then solved by time integration. The blade bending moments, which determine blade stresses, are evaluated using the force summation technique. Systematic studies are made to identify the importance of several parameters including dynamic stall, forward speed, lag stiffness, gust profile, gust penetration rate and gust velocity direction.

Bir, Gunjit↗
NASA NTRS1998

Shear-Sensitive Liquid Crystal Coating Method: Surface-Inclination Effects on Shear Vector Measurements

The shear-sensitive liquid crystal coating (SSLCC) method is an image-based technique for both visualizing dynamic surface-flow phenomena, such as transition and separation, and for measuring the continuous shear-stress vector distribution acting on an aerodynamic surface. Under proper lighting and viewing conditions (discussed below), the coating changes color in response to an applied aerodynamic shear. This color-change response is continuous and reversible, with a response time of milliseconds, and is a function of both the shear magnitude and the shear vector orientation relative to the observer. The liquid crystal phase of matter is a weakly-ordered, viscous, non-Newtonian fluid state that exists between the nonuniform liquid phase and the ordered solid phase of certain organic compounds. Cholesteric liquid crystal compounds possess a helical molecular arrangement that selectively scatters white light, incident along the helical axis, as a three-dimensional spectrum. This property is linked to the helical pitch length, which is within the range of wavelengths in the visible spectrum. The pitch length, and hence the wavelength of the scattered light, is influenced by shear stress normal to the helical axis. This unique optical property produces a measurable color change in response to an applied shearing force. The full-surface shear stress vector measurement method, developed at NASA-Ames, is schematically illustrated. As with the visualization method, the coated test surface is illuminated from the normal direction with white light and the camera is positioned at an above-plane view angle of approximately 30 deg. Experiments have been initiated at NASA Ames to begin the process of quantifying surface-inclination (surface-curvature) effects on shear vector measurement accuracy. In preliminary experiments, surface-inclination angles theta(sub x), theta(sub y) of 0, +/-5, +/-10, and +/-15 deg were employed. In this arrangement, white-light illumination was positioned normal to the untilted test surface, and the camera above-plane view angle was set at 30 deg relative to the untilted test surface. As can be seen, vector-aligned lambda(sub d) values showed no dependence on theta(sub x) or theta(sub y) for absolute values of these tilt angles is less than or equal to 15 deg. Acquisition and analyses of full-surface color images are presently underway to definitively document the insensitivity limits of the shear vector measurement methodology to surface-slope variations.

Reda, Daniel C.↗
NASA NTRS1982

Dynamics of subjective discomfort in motion sickness as measured with a magnitude estimation method

Eight subjects, wearing left-right vision reversing goggles, executed sequences of controlled active head movements to provoke motion sickness. Head movement sequences were interspaced with periods of eye closure and no head movement to permit partial remission of symptoms between sequences. Subjects reported the level of discomfort experienced by using a magnitude estimation technique derived from Stevens' (1957) ratio scaling method. Using this approach, we demonstrated that the time course of subjective discomfort exhibits a profile, similar in all our subjects, characterized by both fast and slow response components. The potential usefulness of magnitude estimation for research on the dynamic properties of the mechanism generating motion sickness symptoms is discussed.

Bock, O. L.↗
NASA NTRS1989

Investigation of a moving-model technique for measuring ground effect

A ground-based testing technique is under development for the measurement of dynamic or time-dependent ground effects which may be present during aircraft approach and landing. The technique utilizes a model moving horizontally over an upwardly-inclined ground plane to simulate rate of descent. Results were obtained in the Langley Research Center (LaRC) Vortex Research Facility (VRF) for a generic 60 delta wing and for an F-18 configuration, both with and without thrust reversing, at forward speeds up to 100 ft/sec. These same models and support hardware were also tested in the LaRC 14 by 22 Foot Subsonic Tunnel at identical conditions (but without rate of descent) with and without a moving-belt ground plane to obtain data for comparison.

Kemmerly, Guy T.↗