Search NASA⌕ Search

SEARCH · Search NASA

Results for “Transmission electron microscopy (TEM)”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

Coalescence of GaP on V-Groove Si

With an increase of control over crystalline defects, metallorganic vapor phase epitaxy (MOVPE)-grown III-V-on-Si multijunction solar cells have seen rapid increases in efficiency in recent years, pointing to a promising path to lower cost III-V solar cells. However, the cost of chemo-mechanical polishing the Si wafers to prepare them for epitaxy is high. The use of V-groove nanopatterns enables similar defect reduction to that achieved on planar wafers, but the nanopatterns can be fabricated with a low-cost process. While V-grooves offer advantages over planar Si, they add complexity to the growth process. In particular, coalescence can cause the formation of threading dislocations, and the highly-directional growth conditions required for coalescence are unusual for MOVPE. We have studied the coalescence of GaP films nucleated directly on V-groove Si by MOVPE. We observed that for optimized growth conditions (V/III=5,000 and T=800 C) two growth modes were possible, and the resulting morphology depended on the exact geometry of the SiNx cap used to cover the (0 0 1)-oriented Si at the tops of the grooves. For caps with a width >100 nm, noncoalescing, nano ridge-like growth terminating in f1 1 1g facets was observed. For narrower caps, coalescence with an RMS roughness of 0.2 nm as measured by atomic force microscopy was observed. We will discuss mechanisms responsible for this phenomenon, including the role of Si from the substrate surface. The dislocation dynamics of this system were studied with electron channeling contrast imaging (ECCI) and transmission electron microscopy (TEM). We find that V-grooves do not block dislocation glide; ECCI measurements show misfit dislocations greater than 10 micrometers long observed to continue perpendicularly across neighboring V-grooves. In addition, all threading dislocations appear to lie on f1 1 1g planes, consistent with the GaP relaxing via glided-in glissile dislocations. The dislocation dynamics and morphological evolution of the coalescence of GaP on Si, possible mechanisms behind the observed phenomenons, and further dislocation mitigation strategies for these materials will be presented.

dislocation dynamics↗

Characteristics and mechanisms of hydrogen-induced quasi-cleavage fracture of lath martensitic steel

Here this study presents an in-depth characterization of the microstructures, crystallographic orientations, and dislocation characteristics beneath hydrogen-induced quasi-cleavage fracture features of an as-quenched, lath martensitic (α') 22MnB5 steel. The fracture surfaces of gaseous hydrogen-embrittled martensitic specimens were analyzed by a combination of multiple analytical tools: scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM), and transmission Kikuchi diffraction (TKD). The dominant fracture mode in the hydrogen-affected zones was quasi-cleavage fracture, which involved significant plasticity, evidenced by plastic zones near tear ridges and a high density of dislocations beneath the quasi-cleavage facets. The martensite constituent sizes, variant orientations, and boundaries influenced the quasi-cleavage surface morphologies. Fractography revealed the occurrence of {100} α' -type cleavage across martensitic laths, developing relatively “flat” quasi-cleavage surfaces, in addition to {110} α' -type cracking likely along lath and block boundaries, and fracture along non-cleavage planes. The likelihood of the formation of the relatively “flat” quasi-cleavage surfaces increased with increasing martensitic constituent sizes. Substantial dislocation bands formed on intersecting {112} α' slip planes within a martensite block below the hydrogen-induced cleavage fractures on {100} α' planes. River markings on the quasi-cleavage surfaces were found to originate from the complex, hierarchical lath martensitic microstructure. Steps and ridges on the quasi-cleavage facets generally linked with the various martensitic boundaries, suggesting that they were produced as a result of crack deviations at those boundaries. The fracture paths and martensite quasi-cleavage mechanisms are discussed in the context of the role of hydrogen and Cottrell cleavage model.

36 MATERIALS SCIENCE↗

Stabilization of NbTe 3 , VTe 3 , and TiTe 3 via Nanotube Encapsulation

The structure of MX 3 transition metal trichalcogenides (TMTs, with M a transition metal and X a chalcogen) is typified by one-dimensional (1D) chains weakly bound together via van der Waals interactions. This structural motif is common across a range of M and X atoms (e.g. NbSe 3 , HfTe 3 , TaS 3 ), but not all M and X combinations are stable. We report here that three new members of the MX 3 family which are not stable in bulk, specifically NbTe 3 , VTe 3 , and TiTe 3 , can be synthesized in the few- to single-chain limit via nano-confined growth within the stabilizing cavity of multi-walled carbon nanotubes. Transmission electron microscopy (TEM) and atomic-resolution scanning transmission electron microscopy (STEM) reveal the chain-like nature and the detailed atomic structure. The synthesized materials exhibit behavior unique to few-chain quasi-1D structures, such as multi-chain spiraling and a trigonal anti-prismatic rocking distortion in the single-chain limit. Density functional theory (DFT) calculations provide insight into the crystal structure and stability of the materials, as well as their electronic structure.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Obtain3D_open

This computer code uses the concept of the parallax to compute the x, y and z coordinates of points found using transmission electron microscopy (TEM), or any transmission imaging technique, using two images, each taken at a different perspective of the region containing the points. Points correspond, but are not limited, to the center of cavities or precipitates, positions of irradiation black dot damage, positions along a dislocation line, or positions along where an interface meets a free surface. Features can include dislocations, interfaces, cavities, precipitates, inclusions etc. The x, y and z coordinates of the points are output in a text file. The code also allows the user to visualize the features containing the points in three dimensions.

Eftink, Benjamin↗

Correlated Microanalysis of Cometary Organic Grains Returned by Stardust

Preliminary examination (PE) of samples returned from Comet 81P/Wild 2 by the NASA Stardust mission revealed a wide variety of carbonaceous samples [e.g. 1]. Carbonaceous matter is present as inclusions, rinds, and films in polyminerallic terminal particles [2-4], as carbon-rich particles along track walls [2, 5, 6], and as organic matter in aerogel around tracks [7, 8]. The organic chemistry of these samples ranges from purely aliphatic hydrocarbons to highly-aromatic material, often modified by various organic functional groups [2, 4, 5, 9-11]. Difficulty arises when interpreting the genesis of these carbonaceous samples, since contaminants could be introduced from the spacecraft [12], aerogel [1, 8], or during sample preparation. In addition, hypervelocity capture into aerogel may have heated cometary material in excess of 1000 C, which could have significantly altered the structure and chemistry of carbonaceous matter. Fortunately, much of this contamination or alteration can be identified through correlated microanalysis with transmission electron microscopy (TEM), scanning-transmission X-ray microscopy (STXM), and nanoscale secondary ion mass spectroscopy (SIMS).

DeGregorio, B. T.↗

The ABCs of phase retrieval: Connecting the acronyms of scanning transmission electron microscopy

High-resolution scanning transmission electron microscopy (S/TEM) is an indispensable tool for characterizing the structure and properties of materials down to the atomic scale. Conventional S/TEM imaging, however, is limited by the phase problem, whereby the phase of the electron exit wave is lost upon detection. Recent advances in diffractive imaging and 4D-STEM have enabled a range of phase-retrieval techniques that computationally reconstruct the missing information encoded in the phase of the transmission function. These approaches offer improved dose efficiency and enhanced sensitivity to weakly scattering signals, extending quantitative imaging to beam-sensitive materials composed of light elements. In this work, we introduce the phase problem in electron microscopy and survey the diverse landscape of phase-retrieval techniques used in the field. Despite their many acronyms and algorithmic variations, these techniques share a common physical and mathematical foundation. We present a unified framework that connects these seemingly distinct methods, from parallax imaging and tilt-corrected bright-field (tcBF-STEM), to aberration-corrected bright-field (acBF-STEM), optimum bright-field (OBF-STEM) and single-sideband (SSB) ptychography, as well as first-moment integrated center of mass techniques (iCOM) and iterative ptychographic algorithms. Based on these insights, we discuss the opportunities and practical limitations of applying these methods across different materials systems, detector designs, and microscope configurations.Graphical abstractRepresentative electron microscopy configurations used for phase retrieval and diffractive imaging in S/TEM: (a) Zernike phase-contrast transmission electron microscopy (TEM), (b) small-convergence-angle four-dimensional scanning transmission electron microscopy (4D-STEM) for nanobeam-based phase reconstruction methods, and (c) large-convergence-angle 4D-STEM for ptychographic and related diffractive imaging techniques reviewed in this work.

36 MATERIALS SCIENCE↗

Identification of the glassy state in nanoparticles by transmission electron microscopy

Identification of amorphous phases in nanoparticles by atomic-resolution transmission electron microscopy (TEM) requires analyses such as tilt-angle-dependent TEM imaging and single-nanoparticle electron diffraction, rather than relying on a single TEM image. Here, the disordered structures of amorphous nanoparticles offer unique atomic configurations and properties that differ from the properties of their crystalline counterparts. These characteristics have motivated the exploration of such materials for mechanical, sensing and catalytic applications. In addition, the formation of amorphous metal nanoparticles is an important endeavour to understand the process of vitrification and the nature of the glassy state. Atomic-resolution transmission electron microscopy (TEM) is increasingly being used as a tool for characterizing structures of nanoparticles produced by vitrification. In this Comment, we discuss the pitfalls of using TEM for ascertaining whether nanoparticles are amorphous. We also make recommendations of best practices.

Alcorn, Francis M. [Sandia National Laboratories (↗

Ordering effects on deformation substructures and strain hardening behavior of a CrCoNi based medium entropy alloy

Here, a CrCoNi based medium entropy alloy with small additions of Ti, Al and Nb (denoted as (CrCoNi) 93 Al 4 Ti 2 Nb) in the as-quenched condition, exhibits tensile properties comparable to those of the equiatomic CrCoNi alloy at room temperature. Dark field transmission electron microscopy (TEM), atomic resolution high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) together with atom probe tomography (APT) show that spatially-localized long range ordering (LRO) L1 2 domains exist in this alloy. The evolution of deformation substructure with plastic deformation in this alloy was characterized using electron backscatter diffraction (EBSD), electron channeling contrast imaging (ECCI) and STEM based techniques including the recently developed weak beam dark field STEM imaging. Plastic deformation occurs by the slip of a/2<110>dislocations, which are narrowly dissociated into Shockley partial dislocations on {111} slip planes. Their dissociation distances in the (CrCoNi) 93 Al 4 Ti 2 Nb alloy are much smaller than the widths of the corresponding partials in the equiatomic CrCoNi alloy due to one or more of the minor alloying elements (Al, Ti, Nb). Dislocation slip in this alloy has a pronounced planar character. The leading dislocations in slip bands glide as pairs due to the existence of LRO domains. Multipoles were formed through the slip of dislocations with opposite signs on adjacent {111} slip planes. Those multipoles serve as building blocks for the formation of subgrain structures consisting of fine slip bands. The distances between slip bands were continuously refined during plastic deformation and dynamic refinement of slip bands plays a crucial role in strain hardening. The effects of LRO domains on planar dislocation slip, the deactivation of deformation twinning and strain hardening of this alloy are discussed.

36 MATERIALS SCIENCE↗

New Synthesis Strategies to Improve Co-Free LiNi0.5Mn0.5O2 Cathodes: Early Transition Metal d0 Dopants and Manganese Pyrophosphate Coating

In this work, we report solution-based doping and coating strategies to improve the electrochemical performance of the Co-free layered oxide cathode LiNi0.5Mn0.5O2 (LNMO). Small amounts of d0 dopants (e.g., Mo6+and Ti4+, 0.5-1 at. %) increase the cathode’s specific capacity, cycling stability, and rate capability. More specifically, a Mo-doped cathode with the nominal composition LiNi0.495Mn0.495Mo0.01O2 achieves a high reversible capacity of 180 mAh/g at 20 mA/g with good retention at higher rates (e.g., 120 mAh/g at 100 mA/g). Effects of 1 at.% Mo dopant on the cathode structure were studied using a suite of characterization tools including X-ray diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM). These measurements demonstrate that Mo6+ reduces Li+/Ni2+cation mixing and mitigates undesirable phase transformations near the cathode surface during cycling. This work also reports the use of an inorganic Mn2P2O7 coating which enhances cycling stability, presumably through formation of a stable cathode electrolyte interphase (CEI) layer. Overall, the synthesis approaches reported herein are quite general and can potentially be expanded to other high voltage LIB cathodes.

Co-free cathodes, d0 cation, pyrophosphate coating↗

Uncovering the Size-dependent Thermal Solid Transformation of Akaganéite

Investigating the structural evolution and phase transformation of iron oxides is crucial for gaining a deeper understanding of geological changes on diverse planets and preparing oxide materials suitable for industrial applications. In this study, we employed in-situ heating techniques in conjunction with transmission electron microscopy (TEM) observations and ex-situ characterization to thoroughly analyze the thermal solid-phase transformation of akaganéite one-dimensional (1D) nanostructures with varying diameters. Our findings offer compelling evidence for a size-dependent morphology evolution in akaganéite 1D nanostructures, which can be attributed to the transformation from akaganéite to maghemite (?-Fe2O3) and subsequent crystal growth. Specifically, we observed that akaganéite nanorods with a diameter of around 50 nm transformed into hollow polycrystalline maghemite nanorods, which demonstrated remarkable stability without arresting crystal growth under continuous heating. In contrast, smaller akaganéite nanoneedles or nanowires with a diameter ranging from 20 to 8 nm displayed a propensity for forming single-crystal nanoneedles or nanowires through phase transformation and densification. By manipulating the size of the precursors, we have developed a straightforward method for the synthesis of single-crystal and polycrystalline maghemite nanowires through solid-phase transformation. These significant findings provide new insights into the size-dependent structural evolution and phase transformation of iron oxides at the nanoscale.

Wang, Xiang↗

Shape Dependence of Pressure-Induced Phase Transition in CdS Semiconductor Nanocrystals

Understanding structural stability and phase transformation of nanoparticles under high pressure is of great scientific interest, as it is one of the crucial factors for design, synthesis, and application of materials. Even though high-pressure research on nanomaterials has been widely conducted, their shape-dependent phase transition behavior still remains unclear. Examples of phase transitions of CdS nanoparticles are very limited, despite the fact that it is one of the most studied wide band gap semiconductors. Here we have employed in-situ synchrotron wide-angle X-ray scattering (WAXS) and transmission electron microscopy (TEM) to investigate the high-pressure behaviors of CdS nanoparticles as a function of particle shapes. We observed that CdS nanoparticles transform from wurtzite to rocksalt phase at elevated pressure in comparison to their bulk counterpart. Phase transitions also vary with particle shape—rod-shaped particles show a partially reversible phase transition and the onset of the structural phase transition pressure decreases with decreasing surface-to-volume ratios, while spherical particles undergo irreversible phase transition with relatively low phase transition pressure. Additionally, TEM images of spherical particles exhibited sintering-induced morphology change after high-pressure compression. Calculations of the bulk modulus reveals that spheres are more compressible than rods in the wurtzite phase. These results indicate that the shape of the particle plays an important role in determining their high-pressure properties. Our study provides important insights into understanding of the phase-structure-property relationship, guiding future design and synthesis of nanoparticles for promising applications.

36 MATERIALS SCIENCE↗

Investigating Deposition Sequence During Synthesis of Pd/Al2O3 Catalysts Modified with Organic Monolayers

Modification of supported metal catalysts with self-assembled monolayers (SAMs) has been shown to improve selectivity and turnover frequencies (TOFs) for many catalytic reactions. However, these benefits are often accompanied by a decrease in overall mass activity due to partial blocking of active sites by the monolayers. Therefore, a potential method for increasing site accessibility is to deposit the active metal (e.g., Pd) after deposition of a SAM modifier on the support material. In this work, Pd/Al2O3 catalysts were synthesized using both a conventional, "metal-first" sequence in which the phosphonic acid (PA) SAM was deposited on Pd/Al2O3 and a "SAM-first" technique in which the ligands were deposited onto the support prior to deposition of the metal. Although metal-first catalysts showed a significant increase in TOF during benzyl alcohol HDO, they exhibited only a modest increase in overall mass activity due to a decrease in the number of active sites. Meanwhile, SAM-first catalysts showed similar improvements in TOF and toluene selectivity but exhibited significantly improved HDO rates compared to metal-first catalysts. The rate increase was attributed to reduced site blocking as evidenced by CO chemisorption measurements. Additionally, analysis of catalysts having high Pd loadings using transmission electron microscopy (TEM) showed that SAM-first catalysts generally resulted in lower average particle sizes than traditionally modified and unmodified catalysts, suggesting that precoating the support surface with PAs changes the way that Pd is deposited during incipient wetness, leading here to improved activity.

catalytic reactions↗

Plasmonic nanorod probes’ journey inside plant cells for in vivo SERS sensing and multimodal imaging

Nanoparticle-based platforms are gaining strong interest in plant biology and bioenergy research to monitor and control biological processes in whole plants. However, in vivo monitoring of biomolecules using nanoparticles inside plant cells remains challenging due to the impenetrability of the plant cell wall to nanoparticles beyond the exclusion limits (5-20 nm). To overcome this physical barrier, we have designed unique bimetallic silver-coated gold nanorods (AuNR@Ag) capable of entering plant cells, while conserving key plasmonic properties in the near-infrared (NIR). To demonstrate cellular internalization and tracking of the nanorods inside plant tissue, we used a comprehensive multimodal imaging approach that included transmission electron microscopy (TEM), confocal fluorescence microscopy, two-photon luminescence (TPL), X-ray fluorescence microscopy (XRF), and photoacoustics imaging (PAI). We successfully acquired SERS signals of nanorods in vivo inside plant cells of tobacco leaves. On the same leaf samples, we applied orthogonal imaging methods, TPL and PAI techniques for in vivo imaging of the nanorods. This study first demonstrates the intracellular internalization of AuNR@Ag inside whole plant systems for in vivo SERS analysis in tobacco cells. This work demonstrates the potential of this nanoplatform as a new nanotool for intracellular in vivo biosensing for plant biology.

Cupil-Garcia, Vanessa↗

14YWT TEM images for LAUR [Images]

Transmission Electron Microscopy (TEM) images attached here are for machine learning study, and these will be uploaded to outer cloud at LANL.

97 MATHEMATICS AND COMPUTING↗

Reflective Fiber Temperature Probe Based on Localized Surface Plasmon Resonance towards Low-Cost and Wireless Interrogation

Reflection fiber temperature sensors functionalized with plasmonic nanocomposite material using intensity-based modulation are demonstrated for the first time. Characteristic temperature optical response of the reflective fiber sensor is experimentally tested using Au-incorporated nanocomposite thin films deposited on the fiber tip, and theoretically validated using a thin-film-optic-based optical waveguide model. By optimizing the Au concentration in a dielectric matrix, Au nanoparticles (NP) exhibit a localized surface plasmon resonance (LSPR) absorption band in a visible wavelength that shows a temperature sensitivity ~0.025%/°C as a result of electron–electron and electron–phonon scattering of Au NP and the surrounding matrix. Detailed optical material properties of the on-fiber sensor film are characterized using scanning electron microscopy (SEM) and focused-ion beam (FIB)-assisted transmission electron microscopy (TEM). Airy’s expression of transmission and reflection using complex optical constants of layered media is used to model the reflective optical waveguide. A low-cost wireless interrogator based on a photodiode transimpedance-amplifier (TIA) circuit with a low-pass filter is designed to integrate with the sensor. The converted analog voltage is wirelessly transmitted via 2.4 GHz Serial Peripheral Interface (SPI) protocols. Feasibility is demonstrated for portable, remotely interrogated next-generation fiber optic temperature sensors with future capability for monitoring additional parameters of interest.

47 OTHER INSTRUMENTATION↗

Flash electropolishing for TEM: Reducing FIB‐induced defects in tungsten with protocols for new materials

Focused ion beam (FIB) milling has become the dominant approach for site-specific transmission electron microscopy (TEM) specimen preparation; however, FIB damage remains a critical limitation for reliable microstructural characterisation, particularly in radiation effects studies. Tungsten is especially susceptible to FIB damage due to its high nuclear stopping power, which promotes the formation and strong diffraction contrast of FIB-induced ‘black spot’ defects that are indistinguishable from very fine irradiation-induced loops/defects resulting from low to intermediate temperature neutron irradiation. In this work, flash electropolishing is systematically evaluated as a post-FIB treatment for minimising preparation-induced artefacts for TEM analysis of tungsten-based alloys. Using a range of non-, ion-, and neutron-irradiated tungsten materials, the effectiveness of flash electropolishing has been assessed through direct comparison with conventional FIB and plasma-FIB preparation including low-energy Ga, Ar, Xe ion cleaning. The results demonstrate that flash electropolishing effectively removes FIB-damaged layers and ‘black spot’ defects, thereby enabling reliable observation of irradiation-induced dislocation structures. Key processing parameters governing flash electropolishing quality – including lamella thickness, applied voltage, polishing duration, electrolyte chemistry, and cathode geometry – have been systematically evaluated, and clear criteria were established for determining when flash electropolishing is required to ensure reliable microstructural analysis. This work also provides practical guidance for implementing flash electropolishing as an artefact-controlled specimen-preparation approach for TEM characterisation of FIB-produced specimens. The systematic protocol can be extended to other, non-tungsten materials.

TEM sample preparation↗

Automated TEM Reveals Intercrystalline Correlations of Conjugated Polymers

Transmission electron microscopy (TEM) continues to transform polymer science by revealing key aspects of chain packing, phase separation and nanoscale structure. The development of instrumentation and data analyses tools is driving the field forward and enabling new experiments. Here, we use automated high-resolution TEM (HRTEM) and image processing to identify the structure of a conjugated polymer used in organic electronics. Analysis of more than 600 HRTEM images reveals lattice parameters and orientation correlations between crystals, including the preferred alignment of neighboring crystals along the same crystallographic direction that is likely the result of liquid crystalline order.

Fair, Ryan A. [Pennsylvania State University, Univ↗

Development of Bismuth and Platinum Bi-Metallic Nanoparticles to Enhance Melt Wire Temperature Resolution

Advanced manufacturing (AM) based on direct-write (DW) technologies has emerged as the predominant enabler for the fabrication of active and passive sensors to be deployed in harsh operating environments seen in a nuclear reactor. Recently, Idaho National Laboratory and Boise State University have recently established capabilities to incorporate advanced manufacturing (AM) methods to accelerate, modernize and enhance functionality of nuclear sensors and instrumentation to achieve the goal of enhancing the safety and efficiency of nuclear reactors. A significant thrust of this work includes the development of nuclear relevant feedstock materials compatible with a variety of direct-write processes for the development, fabrication and testing of AM sensors for peak temperature detection and neutron flux monitoring. For this report, bismuth and bismuth/platinum (BiPt) bi-metallic nanoparticles were synthesized using wet chemical approaches to develop bi-metallic feedstock materials to enhance the sensitivity of melt wires for peak temperature detection. Nanoparticle characterization was performed with Transmission Electron Microscopy (TEM) for nanoparticle composition and size, Transmission X-Ray Diffraction Fluorescence (TXRF) for nanoparticle composition, and Differential Scanning Calorimetry to elucidate the melting point of BiPt bi-metallic nanoparticles. Preliminary results indicate bi-metallic BiPt nanoparticles as a viable pathway for fabricating high resolution AM melt wires.

36 MATERIALS SCIENCE↗