Results for “Trip height” — Page 2

NASA NTRS2006

Shuttle Return To Flight Experimental Results: Protuberance Effects on Boundary Layer Transition

The effect of isolated roughness elements on the windward boundary layer of the Shuttle Orbiter has been experimentally examined in the Langley Aerothermodynamic Laboratory in support of an agency-wide effort to prepare the Shuttle Orbiter for return to flight. This experimental effort was initiated to provide a roughness effects database for developing transition criteria to support on-orbit decisions to repair damage to the thermal protection system. Boundary layer transition results were obtained using trips of varying heights and locations along the centerline and attachment lines of 0.0075-scale models. Global heat transfer images using phosphor thermography of the Orbiter windward surface and the corresponding heating distributions were used to infer the state of the boundary layer (laminar, transitional, or turbulent). The database contained within this report will be used to formulate protuberance-induced transition correlations using predicted boundary layer edge parameters.

Liechty, Derek S.↗

NASA NTRS2009

Aerothermodynamic Characteristics of Boundary Layer Transition and Trip Effectiveness of the HIFiRE Flight 5 Vehicle

An experimental wind tunnel test was conducted in the NASA Langley Research Center s 20-Inch Mach 6 Tunnel in support of the Hypersonic International Flight Research Experimentation Program. The information in this report is focused on the Flight 5 configuration, one in a series of flight experiments. This report documents experimental measurements made over a range of Reynolds numbers and angles of attack on several scaled ceramic heat transfer models of the Flight 5 vehicle. The heat transfer rate was measured using global phosphor thermography and the resulting images and heat transfer rate distributions were used to infer the state of the boundary layer on the windside, leeside and side surfaces. Boundary layer trips were used to force the boundary layer turbulent, and a study was conducted to determine the effectiveness of the trips with various heights. The experimental data highlighted in this test report were used determine the allowable roughness height for both the windside and side surfaces of the vehicle as well as provide for future tunnel-to-tunnel comparisons.

Berger, Karen T.↗

NASA NTRS2008

Aerothermodynamic Testing and Boundary Layer Trip Sizing of the HIFiRE Flight 1 Vehicle

An experimental wind tunnel test was conducted in the NASA Langley Research Center s 20-Inch Mach 6 Air Tunnel in support of the Hypersonic International Flight Research Experimentation Program. The information in this article is focused on the Flight 1 configuration, the first in a series of flight experiments. The article documents experimental measurements made over a Reynolds numbers range of 2.1x10(exp 6)/ft to 5.6x10(exp 6)/ft and angles of attack of -5 to +5 deg on several scaled ceramic heat transfer models of the Flight 1 configuration. Global heat transfer was measured using phosphor thermography and the resulting images and heat transfer distributions were used to infer the state of the boundary layer on the vehicle windside and leeside surfaces. Boundary layer trips were used to force the boundary layer turbulent and the experimental data highlighted in this article were used to size and place the boundary layer trip for the flight vehicle. The required height of the flight boundary layer trip was determined to be 0.079 in and the trip was moved from the design location of 7.87 in to 20.47 in to ensure that augmented heating would not impact the laminar side of the vehicle. Allowable roughness was selected to be 3.2x10(exp -3) in.

Berger, Karen T.↗

NASA NTRS2013

Aeroheating Measurement of Apollo Shaped Capsule with Boundary Layer Trip in the Free-piston Shock Tunnel HIEST

An aeroheating measurement test campaign of an Apollo capsule model with laminar and turbulent boundary layer was performed in the free-piston shock tunnel HIEST at JAXA Kakuda Space Center. A 250mm-diameter 6.4%-scaled Apollo CM capsule model made of SUS-304 stainless steel was applied in this study. To measure heat flux distribution, the model was equipped with 88 miniature co-axial Chromel-Constantan thermocouples on the heat shield surface of the model. In order to promote boundary layer transition, a boundary layer trip insert with 13 "pizza-box" isolated roughness elements, which have 1.27mm square, were placed at 17mm below of the model geometric center. Three boundary layer trip inserts with roughness height of k=0.3mm, 0.6mm and 0.8mm were used to identify the appropriate height to induce transition. Heat flux records with or without roughness elements were obtained for model angles of attack 28º under stagnation enthalpy between H(sub 0)=3.5MJ/kg to 21MJ/kg and stagnation pressure between P(sub 0)=14MPa to 60MPa. Under the condition above, Reynolds number based on the model diameter was varied from 0.2 to 1.3 million. With roughness elements, boundary layer became fully turbulent less than H(sub 0)=9MJ/kg condition. However, boundary layer was still laminar over H(sub 0)=13MJ/kg condition even with the highest roughness elements. An additional experiment was also performed to correct unexpected heat flux augmentation observed over H(sub 0)=9MJ/kg condition.

Hideyuki, TANNO↗

NASA NTRS1972

Discrete sonic jets used as boundary-layer trips at Mach numbers of 6 and 8.5

The effect of discrete three-dimensional sonic jets used to promote transition on a sharp-leading-edge flat plate at Mach numbers of 6 and 8.5 and unit Reynolds numbers as high as 2.5 x 100,000 per cm in the Langley 20-inch hypersonic tunnels is discussed. An examination of the downstream flow-field distortions associated with the discrete jets for the Mach 8.5 flow was also conducted. Jet trips are found to produce lengths of turbulent flow comparable to those obtained for spherical-roughness-element trips while significantly reducing the downstream flow distortions. A Reynolds number based upon secondary jet penetration into a supersonic main flow is used to correlate jet-trip effectiveness just as a Reynolds number based upon roughness height is used to correlate spherical-trip effectiveness. Measured heat-transfer data are in agreement with the predictions.

Stone, D. R.↗

NASA NTRS2021

Wake Instability Behind Isolated Trip Near the Leading Edge of the BOLT-II Configuration

The BOLT-II (Holden Mission) configuration is an extended version of the BOLT flight article and depicts hypersonic boundary-layer transition in the presence of multiple and potentially interacting instability mechanisms. Several numerical studies of the boundary-layer instabilities over these configurations have been reported in the recent literature, including our previous studies of the modal instability characteristics of boundary-layer streaks adjacent to the minor-axis symmetry plane of the BOLT configuration and the wake instabilities behind a diamond planform (“pizza-box”) trip along the symmetry plane on the secondary side of the BOLT-II configuration. The present work extends the latter study to a scaled version of the same trip that is located in the region of nonzero crossflow in the vicinity of the leading edge at X/L = 0.5. Collectively, the trips along the symmetry plane and near the leading edge are the focus of the NASA roughness experiment on the secondary side of the BOLT-II configuration. The laminar basic state computation at the nominal flight design condition of Re ∞ = 5.44 x 10 6 /m and Re ∞ = 2.5 x 10 6 /m shows that the leading-edge trip with k/δ ≈ 0.70 and planform-side-length-to-height ratio of b/k = 3.0 induces multiple asymmetric, longitudinal streaks within the trip wake. The most prominent streak among these resembles a finite amplitude crossflow vortex, and it supports the amplification of multiple families of unstable modes. The application of multi-dimensional instability analysis to the wake flow reveals that the most amplified unstable mode can achieve a peak N-factor of up to 20 by X/L = 0.80, indicating that the onset of transition is more than likely to occur within eighty percent of the model length. To the best of our knowledge, the present study represents the first analysis including nonparallel and curvature effects on hypersonic tripwake instabilities in the presence of boundary-layer crossflow over a three-dimensional configuration.

Boundary layer transition↗

NASA NTRSDate not supplied

BOLT II Roughness-Side Flight Results

An initial review of the roughness data from the BOLT II flight is provided. The BOLT II roughness experiment was designed to investigate discrete trips in flight based on the diamond configuration, which has been shown to be an efficient vortex generator and boundary layer trip from extensive ground-based testing. There were three trip locations chosen for the flight test and their size (height and width) were tailored to the local boundary layer thickness, but all three were expected to trip at the same time or flight condition. Details about the flight vehicle design, instrumentation, and best estimated trajectory are discussed. The present paper is limited to only a review and analysis of the thermocouple data. Boundary layer transition onset times are derived from the thermocouple analysis, thus allowing an initial assessment of the performance of these discrete trips. Since the three trips were sized to trip the boundary layer at the same time, based on a previous wind tunnel study, the present analysis indicates that they performed as expected.

Hypersonic↗

NASA NTRS2021

Hypersonic Second Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

NASA NTRS2021

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

NASA NTRS2021

Hypersonic Second-Mode Instability Response to Shaped Roughness

An experimental campaign was conducted on a 7-degree half-angle cone in the NASA Langley Research Center 20-Inch Mach 6 Wind Tunnel to examine the influence of arrays of regularly spaced roughness elements on instability growth and transition. The primary element shape was a pair of elliptical planform ramps that were inclined at equal and opposite angles with respect to the local streamwise direction. The element shapes were designed to induce transient growth disturbances that would lead to sustained azimuthal modulation of the boundary layer flow while limiting the nearfield disturbances to avoid an immediate, i.e., effective tripping of the boundary layer. The bulk of the run matrix consisted of testing different element height sat free stream unit Reynolds numbers ranging from 9.8 to 13.1 million per meter. Other element shapes previously designed for tripping hypersonic boundary layers were also implemented. The model was instrumented with surface mounted Kulite ® and PCB ® pressure transducers and thermocouples. Spectra from the PCBs ® indicated clear suppression of the second-mode instability; however, neither the PCB ® spectra nor the heat transfer data presented strong evidence for delayed turbulent flow. Complementary stability computations likewise demonstrated second-mode reduction, particularly just downstream of the roughness, but also revealed a rise in first mode (streak-instability) amplitudes from the baseline that was likely responsible for the earlier transition observed for taller roughness cases.

Hypersonics↗

NASA NTRS2023

Experimental Aeroheating Study in NASA LaRC 20-Inch Mach 6 Air Tunnel: Discrete Roughness on BOLT – Test 7071

An experimental study of the effect of discrete roughness (trips) on boundary layer transition was conducted in the NASA Langley Research Center 20-Inch Mach 6 Air Tunnel on the BOLT shape. This study was intended to obtain results that could eventually be compared against experimental results from other facilities, as well as from flight. The trip locations for the present study were selected to correspond to those used for the flight vehicle, but the heights of these discrete roughness elements were varied. Infrared thermography was used to obtain images of the effect of these trips on the behavior of the boundary layer. This report is intended as a quick release of experimental results.

hypersonic↗

NASA NTRS2010

High-Speed Boundary-Layer Transition Induced by an Isolated Roughness Element

Progress on an experimental effort to quantify the instability mechanisms associated with roughness-induced transition in a high-speed boundary layer is reported in this paper. To simulate the low-disturbance environment encountered during high-altitude flight, the experimental study was performed in the NASA-Langley Mach 3.5 Supersonic Low-Disturbance Tunnel. A flat plate trip sizing study was performed first to identify the roughness height required to force transition. That study, which included transition onset measurements under both quiet and noisy freestream conditions, confirmed the sensitivity of roughness-induced transition to freestream disturbance levels. Surveys of the laminar boundary layer on a 7deg half-angle sharp-tipped cone were performed via hot-wire anemometry and pitot-pressure measurements. The measured mean mass-flux and Mach-number profiles agreed very well with computed mean-flow profiles. Finally, surveys of the boundary layer developing downstream of an isolated roughness element on the cone were performed. The measurements revealed an instability in the far wake of the roughness element that grows exponentially and has peak frequencies in the 150 to 250 kHz range.

Kegerise, Michael A.↗

NASA NTRS2021

Transition Analysis for Isolated Trips on BOLT-II Wind-Tunnel and Flight Configuration

The BOLT-II configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. The present paper is related to the NASA-led roughness experiment on the secondary side of the BOLT-II configuration. First, computations are performed to aid mean-flow based correlations for the transition measurements acquired during an experimental campaign in the Ludwieg Tube facility at the United States Air Force Academy. To that end, both laminar and turbulent flow computations are performed for selected conditions of the experiment with a 1:3 scale model of the slightly shorter BOLT configuration. The variation in well-known correlation parameters for transition due to isolated roughness elements with respect to element position, height, and flow Reynolds number is delineated. Furthermore, the wake instability theory is used to examine the amplification of unstable disturbances behind the centerline trip at the design conditions of the BOLT-II flight experiment and for its dynamically scaled version on the 1:3 scale model of the wind tunnel experiment. To our knowledge, this study represents the first analysis of the wake instabilities in the presence of a prominent entropy layer outside the boundary layer. At the nominal flight design condition of Re ∞ ) = 5.44 and Re ∞ = 2.5 x 10 6 /m, a diamond planform (“pizza-box”) trip with k/δ = 0.70 and planform-halfwidth-to-height ratio of b/k = 3.0 at X/L = 0.254 induces a strong distortion of the boundary-layer flow in the vicinity of the symmetry plane, such that the wake structure includes a centerline streak produced by the flow retardation behind the trip along with multiple additional, prominent vorticity structures representing the necklace vortex system. Stability results reveal that each of these streaks can support a strong amplification of wake instabilities within a frequency band of 95 kHz–255 kHz, with a peak N-factor of greater than 15 beyond X/L ≈ 0.42. The dynamically scaled wind tunnel configuration with Re ∞ = 20.25 x 10 6 /m is also found to support N > 15 at similar axial stations.

BOLT↗

NASA NTRS2021

Transition Analysis for Isolated Trips on BOLT-II Wind-Tunnel and Flight Configuration

The BOLT-II configuration designed for an upcoming flight experiment exemplifies the complexities of hypersonic boundary layer transition in the presence of multiple and potentially interacting instability mechanisms. The present paper is related to the NASA-led roughness experiment on the secondary side of the BOLT-II configuration. First, computations are performed to aid mean-flow based correlations for the transition measurements acquired during an experimental campaign in the Ludwieg Tube facility at the United States Air Force Academy. To that end, both laminar and turbulent flow computations are performed for selected conditions of the experiment with a 1:3 scale model of the slightly shorter BOLT configuration. The variation in well-known correlation parameters for transition due to isolated roughness elements with respect to element position, height, and flow Reynolds number is delineated. Furthermore, the wake instability theory is used to examine the amplification of unstable disturbances behind the centerline trip at the design conditions of the BOLT-II flight experiment and for its dynamically scaled version on the 1:3 scale model of the wind tunnel experiment. To our knowledge, this study represents the first analysis of the wake instabilities in the presence of a prominent entropy layer outside the boundary layer. At the nominal flight design condition of Re ∞ ) = 5.44 and Re ∞ = 2.5 x 10 6 /m, a diamond planform (“pizza-box”) trip with k/δ = 0.70 and planform-halfwidth-to-height ratio of b/k = 3.0 at X/L = 0.254 induces a strong distortion of the boundary-layer flow in the vicinity of the symmetry plane, such that the wake structure includes a centerline streak produced by the flow retardation behind the trip along with multiple additional, prominent vorticity structures representing the necklace vortex system. Stability results reveal that each of these streaks can support a strong amplification of wake instabilities within a frequency band of 95 kHz–255 kHz, with a peak N-factor of greater than 15 beyond X/L ≈ 0.42. The dynamically scaled wind tunnel configuration with Re ∞ = 20.25 x 10 6 /m is also found to support N > 15 at similar axial stations.

BOLT↗

NASA NTRS1973

Venus - Radar determination of gravity potential.

We describe a method for the determination of the gravity potential of Venus from multiple-frequency radar measurements. The method is based on the strong frequency dependence of the absorption of radio waves in Venus' atmosphere. Comparison of the differing radar reflection intensities at several frequencies yields the height of the surface relative to a reference pressure contour; combination with measurements of round-trip echo delays allows the pressure, and hence the gravity potential contour, to be mapped relative to the mean planet radius. Since calibration data from other frequencies are unavailable, the absorption-sensitive Haystack Observatory data have been analyzed under the assumption of uniform surface reflectivity to yield a gravity equipotential contour for the equatorial region and a tentative upper bound of .0006 on the fractional difference of Venus' principal equatorial moments of inertia.

Shapiro, I. I.↗

NASA NTRS1972

Sweep effect on the drag of rows of perpendicular circular cylinders in a laminar boundary layer at supersonic free-stream velocities

Drag measurements were obtained for circular cylinders attached perpendicularly to a flat-plate surface. Measurements were obtained for a single cylinder and for rows of cylinders. The cylinders were alined at various sweep angles relative to the free-stream velocity vector and at spacings appropriate for roughness elements used as boundary layer trips. The drag measurements were obtained for Mach numbers of 3.95 and 4.60, ratios of cylinder height to an undisturbed laminar boundary layer displacement thickness of approximately 1.0 to 3.0, a cylinder height-to-diameter ratio of approximately 2, and sweep angles up to 60. A complete presentation of the experimental results is given. A discussion of the more significant findings, including the most appropriate parameters for correlating the experimental results, is presented.

Lamb, M.↗

NASA NTRS1986

Effects of wind-tunnel noise on swept-cylinder transition at Mach 3.5

Transition data are reported for circular cylinders at swept angles of 45 and 60 degrees in the Mach 3.5 pilot-low-disturbance tunnel where free-stream noise levels are varied from approximately .05-0.5 percent in terms of the rms fluctuating pressure normalized by the mean static pressure. Results indicate that end plate or boundary layer trip disturbances at the upstream end of the cylinders cause turbulent flow along the entire test Reynolds number range of 10-170 thousand per inch. With all end plate and trip disturbances removed, transition at the attachment lines occurred at free-stream Reynolds numbers based on diameters of about 70-80 thousand, independent of stream noise levels. The installation of small trips on the attachement lines caused transition at lower Reynolds numbers, depending on both the roughness height and the wind tunnel noise level.

Creel, T. R., Jr.↗

NASA NTRS1986

Effects of cone surface waviness and freestream noise on transition in supersonic flow

A comparison of transition on wavy-wall and smooth-wall cones in a Mach 3.5 wind tunnel is made under conditions of either low freestream noise (quiet flow) or high freestream noise (noisy flow). The noisy flow compares to that found in conventional wind tunnels while the quiet flow gives transitional Reynolds numbers on smooth sharp cones comparable to those found in flight. The waves were found to have a much smaller effect on transition than similar sized trip wires. A satisfatory correlating parameter for the effect of waves on transition was simply the wave height-to-length ratio. A given value of this ratio was found to cause the same percentage change in transition location in quiet and noisy flows.

Morrisette, E. L.↗