Search NASA⌕ Search

SEARCH · Search NASA

Results for “Truss analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Dynamics of trusses having nonlinear joints

The transient analysis of trusses having nonlinear joints can be accomplished using the residual force technique. The technique was applied a two degree of freedom spring mass system, a four bay planar truss, and an actual ten bay deployable truss. Joints chosen for analysis were the nonlinear gap joints and the linear Voigt joints. Results from the nonlinear gap analyses generally indicate that coupling between the modes can display some interesting effects during free vibration. One particularly interesting effect was that the damping of the structure appeared to be higher than could be accounted for from modal damping alone. Energy transferral from the lower to the higher modes was found to exist as a result of the modal coupling. The apparently increased damping was due to the fact that the energy transferred to the higher modes is inherently dissipated more quickly. Another interesting phenomenon was that the lower modes could drive the higher modes even during free vibration and that these modes could display a rather large quasi-steady state behavior even when modal damping was present. Gaps were also found to increase the amplitude and period of the free vibration response as expected.

Chapman, J. M.↗
NASA NTRSDate not supplied

High-Fidelity Flight Dynamic Analysis of Transonic Truss-Braced Wing

This paper presents a high-fidelity flight dynamic analysis of the Mach 0.8 Transonic Truss-Braced Wing (TTBW). Unsteady RANS CFD simulations of the Mach 0.8 TTBW in pitch, plunge, roll, and yaw oscillations are conducted in FUN3D. The time-domain data are transformed into the frequency-domain data by Fourier series. Transfer functions of the dynamic stability derivatives are then estimated by a frequency-domain re- gression. The dynamic stability derivatives with respect to the angle of attack are determined by the regression of the unsteady aerodynamic coefficients for the plunge motion. The dynamic stability derivatives with re- spect to the pitch rate are determined by the regression of the differential unsteady aerodynamic coefficients for the pitch motion upon the removal of the angle of attack contribution by the plunge motion. Similarly, dynamic stability derivatives with respect to the angle of sideslip, roll rate, and yaw rates are determined from the frequency domain regression. The longitudinal and lateral-direction flight dynamic models of the Mach 0.8 TTBW are constructed from these dynamic stability derivatives. The eigenvalues of the aircraft modes are analyzed to determine the vehicle stability.

Aircraft Stability and Control↗
NASA NTRS1992

Finite element-finite difference thermal/structural analysis of large space truss structures

A technique of automated and efficient thermal-structural processing of truss structures that interfaces the finite element and finite difference method was developed. The thermal-structural analysis tasks include development of the thermal and structural math models, thermal analysis, development of an interface and data transfer between the models, and finally an evaluation of the thermal stresses and displacements in the structure. Consequently, the objective of the developed technique was to minimize the model development time, in order to assure an automatic transfer of data between the thermal and structural models as well as to minimize the computer resources needed for the analysis itself. The method and techniques described are illustrated on the thermal/structural analysis of the Space Station Freedom main truss.

Warren, Andrew H.↗
NASA NTRS1992

Truss topology optimization with simultaneous analysis and design

Strategies for topology optimization of trusses for minimum weight subject to stress and displacement constraints by Simultaneous Analysis and Design (SAND) are considered. The ground structure approach is used. A penalty function formulation of SAND is compared with an augmented Lagrangian formulation. The efficiency of SAND in handling combinations of general constraints is tested. A strategy for obtaining an optimal topology by minimizing the compliance of the truss is compared with a direct weight minimization solution to satisfy stress and displacement constraints. It is shown that for some problems, starting from the ground structure and using SAND is better than starting from a minimum compliance topology design and optimizing only the cross sections for minimum weight under stress and displacement constraints. A member elimination strategy to save CPU time is discussed.

Sankaranarayanan, S.↗
NASA NTRSDate not supplied

Flutter Analysis of the Transonic Truss-Braced Wing Aircraft Using Transonic Correction

This paper describes a flutter analysis method for the Transonic Truss-Braced Wing aircraft using a vortex lattice method coupled to an unsteady transonic correction method to account for unsteady aerodynamics in transonic flow. A steady-state vortex-lattice model of the Truss-Braced Wing aircraft is developed using vortex lattice code VSPAERO. A transonic and viscous flow correction method is implemented in the VSPAERO model to account for steady-state transonic and viscous flow effects using transonic small disturbance code TSFOIL coupled to an in-house integral boundary layer code. In addition, a wing-strut interference correction method is developed to account for the transonic interference aerodynamics in the strut juncture region using high-fidelity CFD code FUN3D. A structural dynamic finite-element model of the Truss-Braced Wing aircraft is developed using BEAM3D in-house finite-element code and is coupled to the VSPAERO. The BEAM3D model includes a geometric nonlinearity due to the tension in the strut which causes a deflection-dependent nonlinear stiffness. An unsteady transonic correction method is developed to better capture the unsteady aerodynamics in transonic flow. The unsteady transonic correction method makes use of the Theodorsen’s theory to account for the amplitude and phase shift of the unsteady lift coefficient in transonic flow. A preliminary flutter analysis of the Truss-Braced Wing aircraft is conduct to illustrate the unsteady transonic correction approach.

Nhan Nguyen↗
NASA NTRS2001

Adaptive Multi-Layer LMS Controller Design and Application to Active Vibration Suppression on a Truss and Proposed Impact Analysis Technique

This research develops an adaptive controller that actively suppresses a single frequency disturbance source at a remote position and tests the system on the NPS Space Truss. The experimental results are then compared to those predicted by an ANSYS finite element model. The NPS space truss is a 3.7-meter long truss that simulates a space-borne appendage with sensitive equipment mounted at its extremities. One of two installed piezoelectric actuators and an Adaptive Multi-Layer LMS control law were used to effectively eliminate an axial component of the vibrations induced by a linear proof mass actuator mounted at one end of the truss. Experimental and analytical results both demonstrate reductions to the level of system noise. Vibration reductions in excess of 50dB were obtained through experimentation and over 100dB using ANSYS, demonstrating the ability to model this system with a finite element model. This report also proposes a method to use distributed quartz accelerometers to evaluate the location, direction, and energy of impacts on the NPS space truss using the dSPACE data acquisition and processing system to capture the structural response and compare it to known reference Signals.

Barney, Timothy A.↗
NASA NTRS2014

Aerodynamic Analysis of the Truss-Braced Wing Aircraft Using Vortex-Lattice Superposition Approach

The SUGAR Truss-BracedWing (TBW) aircraft concept is a Boeing-developed N+3 aircraft configuration funded by NASA ARMD FixedWing Project. This future generation transport aircraft concept is designed to be aerodynamically efficient by employing a high aspect ratio wing design. The aspect ratio of the TBW is on the order of 14 which is significantly greater than those of current generation transport aircraft. This paper presents a recent aerodynamic analysis of the TBW aircraft using a conceptual vortex-lattice aerodynamic tool VORLAX and an aerodynamic superposition approach. Based on the underlying linear potential flow theory, the principle of aerodynamic superposition is leveraged to deal with the complex aerodynamic configuration of the TBW. By decomposing the full configuration of the TBW into individual aerodynamic lifting components, the total aerodynamic characteristics of the full configuration can be estimated from the contributions of the individual components. The aerodynamic superposition approach shows excellent agreement with CFD results computed by FUN3D, USM3D, and STAR-CCM+.

vortex lattice method↗
NASA NTRS1995

Structural Analysis and Testing of an Erectable Truss for Precision Segmented Reflector Application

This paper describes analysis and test results obtained at Langley Research Center (LaRC) on a doubly curved testbed support truss for precision reflector applications. Descriptions of test procedures and experimental results that expand upon previous investigations are presented. A brief description of the truss is given, and finite-element-analysis models are described. Static-load and vibration test procedures are discussed, and experimental results are shown to be repeatable and in generally good agreement with linear finite-element predictions. Truss structural performance (as determined by static deflection and vibration testing) is shown to be predictable and very close to linear. Vibration test results presented herein confirm that an anomalous mode observed during initial testing was due to the flexibility of the truss support system. Photogrammetric surveys with two 131-in. reference scales show that the root-mean-square (rms) truss-surface accuracy is about 0.0025 in. Photogrammetric measurements also indicate that the truss coefficient of thermal expansion (CTE) is in good agreement with that predicted by analysis. A detailed description of the photogrammetric procedures is included as an appendix.

Collins, Timothy J.↗
NASA NTRS1972

Comparison of NASTRAN and STARDYNE static analysis of a graphite fiber reinforced plastic truss structure

A static and buckling analysis of the ATS-F&G spacecraft reflector support truss (RST) and bridge truss assembly using NASTRAN was conducted. The RST is fabricated from a new material, graphite fiber reinforced plastic. A comparison is made with the NASTRAN results and the results of a similar analysis conducted using the stardyne program. The results of an actual static load test are also compared.

Honeycutt, G. H.↗
NASA NTRS1983

A closed-loop principal component analysis of a tetrahedral truss

A tetrahedral truss, representative of a fairly broad class of large space structures, is considered. A method, measuring the dynamical importance of each elastic mode when the structure is under feedback control, is presented. The main conclusion is that the closed-loop importance of each vibration mode depends on the robustness requirements. Also, there appears to be a conflict between precise control of a given node of the structure and stability margin, these two requirements leading to contradictory classifications of the modes by order of importance.

Jonckheere, E. A.↗
NASA NTRS1989

Parallel processing techniques for finite element analysis of nonlinear large truss structures

Methods were developed for parallel processing of finite element solutions of large truss structures. The parallel processing techniques were implemented in two stages, i.e., the repeated forming of the nonlinear global stiffness matrix and the solving of the global system of equations. The Sequent Balance 21000 parallel computer was employed to demonstrate the procedures and the speed-up.

Chien, L. S.↗
NASA NTRS1989

Mini-mast dynamic analysis using the truss-beam model

The Mini-Mast is a generic space truss designed by Astro Aerospace Corp. A 210 meter truss located in the Structural Dynamics research Lab of NASA Langley is used in comprehensive active vibration control experiments on a realistic large space structure. Some predictions of the natural frequencies and mode shapes were made based on the Finite Element model. The purpose here is to use the Truss-Beam model developed by Elias G. Abu-Saba to predict the natural frequencies of the Mini-Mast and then compare the results with those obtained from the FE model. Imperfections of the joints are modeled, and joint contribution to the flexibility matrix of the structure is noted. The natural frequencies are obtained. An iterative procedure is used to enhance the Truss-Beam model by comparing these results with experimental ones.

Abu-Saba, Elias G.↗
NASA NTRS1991

Kinematic analysis of generalized adaptive trusses

Adaptive trusses offer the greatest stiffness and strength for a given weight of any articulated structure or mechanism. Because of this, there are many potential extraterrestrial applications of these variable-geometry trusses, including serpentine manipulators, payload isolation, tracking, pointing and docking mechanisms, and gimbals. All of these applications will require the ability to precisely control the kinematic parameters of the mechanism, including position, velocity, and acceleration. This paper explores the fundamental nature of adaptive trusses by examining the basic truss elements or unit cells. A general method for analyzing forward and inverse motion of all the basic truss units is presented, followed by a more efficient formulation for the octahedral unit cell. Finally, general closed-form techniques are presented for finding velocity, acceleration, and all higher derivatives of truss motion.

Tidwell, Paul H.↗
NASA NTRS1993

Two pass method and radiation interchange processing when applied to thermal-structural analysis of large space truss structures

A method of efficient and automated thermal-structural processing of very large space structures is presented. The method interfaces the finite element and finite difference techniques. It also results in a pronounced reduction of the quantity of computations, computer resources and manpower required for the task, while assuring the desired accuracy of the results.

Warren, Andrew H.↗
NASA NTRS2015

Aeroelastic Analysis of SUGAR Truss-Braced Wing Wind-Tunnel Model Using FUN3D and a Nonlinear Structural Model

Considerable attention has been given in recent years to the design of highly flexible aircraft. The results of numerous studies demonstrate the significant performance benefits of strut-braced wing (SBW) and trussbraced wing (TBW) configurations. Critical aspects of the TBW configuration are its larger aspect ratio, wing span and thinner wings. These aspects increase the importance of considering fluid/structure and control system coupling. This paper presents high-fidelity Navier-Stokes simulations of the dynamic response of the flexible Boeing Subsonic Ultra Green Aircraft Research (SUGAR) truss-braced wing wind-tunnel model. The latest version of the SUGAR TBW finite element model (FEM), v.20, is used in the present simulations. Limit cycle oscillations (LCOs) of the TBW wing/strut/nacelle are simulated at angle-of-attack (AoA) values of -1, 0 and +1 degree. The modal data derived from nonlinear static aeroelastic MSC.Nastran solutions are used at AoAs of -1 and +1 degrees. The LCO amplitude is observed to be dependent on AoA. LCO amplitudes at -1 degree are larger than those at +1 degree. The LCO amplitude at zero degrees is larger than either -1 or +1 degrees. These results correlate well with both wind-tunnel data and the behavior observed in previous studies using linear aerodynamics. The LCO onset at zero degrees AoA has also been computed using unloaded v.20 FEM modes. While the v.20 model increases the dynamic pressure at which LCO onset is observed, it is found that the LCO onset at and above Mach 0.82 is much different than that produced by an earlier version of the FEM, v. 19.

Bartels, Robert E.↗
NASA NTRSDate not supplied

Aeroelastic Analysis of Mach 0.8 Transonic Truss-Braced Wing Aircraft

This paper presents an aeroelastic analysis of the Mach 0.8 Transonic Truss-Braced Wing(TTBW) aircraft jig shape using an in-house developed tool based on VSPAERO. A vortex-lattice model of the Mach 0.8 TTBW model is developed, and a transonic and viscous flow correction method is implemented to account for transonic and viscous flow effects. A correction method for the wing-strut interference aerodynamics is developed and applied to the VSPAERO solver. The Galerkin method is used to calculate the geometry deformation under aerodynamic force. The aero-structural analysis solver VSPAERO coupled to the mode shapes computed by NASTRAN using the Galerkin method provides a rapid aircraft aero-structual analysis. A high-fidelity CFD solver FUN3D is used to verify the results. The aeroelastic simulation results show that the aeroelastic lift coefficient is reduced about0.05∼0.07, drag polar is not affected by aeroelasticity, and the pitching moment is reduced about 30% at Mach0.8 and altitude 40,000 ft.

TTBW Aeroelastic↗
NASA NTRS1993

Preliminary analysis and design optimization of the short spacer truss of Space Station Freedom

The analysis, dynamic simulation, and design optimization of the short spacer truss of the Space Station Freedom are presented in this report. The short spacer truss will be positioned between the integrated equipment assembly (IEA) and another truss, called the long spacer truss, in the Space Station Freedom. During its launch in the Space Shuttle, the truss will be subjected to considerable in-span distributed inertia loads due to shuttle accelerations. The short spacer truss, therefore, has been modeled as a space frame to account for flexural response. Several parameters have been assumed, since the design specifications are in the process of development; hence the results presented should be considered preliminary. However, the automated analysis and design capabilities that have been developed can readily be used to generate an optimum design of the short spacer truss once the actual specifications have been determined. This report includes static and dynamic analyses of the short spacer truss, which have been obtained with the linear elastic code LE-HOST (in these analyses, LE-HOST data files have been automated to facilitate their future use for different design specifications of the short spacer truss); the dynamic animation of the short spacer truss, which has been carried out by using the results of the dynamic analysis and a post-processing feature of the modeling code PATRAN; and the optimum-weight design of the spacer truss, which was obtained under prescribed stress, displacement, and frequency constraints by using the design code COMETBOARDS. Examination of the analysis and design results revealed that the design could be improved if the configuration of the short spacer truss were modified to a certain extent. A modified configuration, which may simplify fabrication, has been suggested. The performance of this configuration has been evaluated and was found to be satisfactory under both static and dynamic conditions.

Gendy, A. S.↗