Verification Study of Metal Additive Manufactured Stretch-Dominated Lattices
Abstract not provided.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Abstract not provided.
This report on the adequacy of the plasma viscosity model implemented in LANL’s ASC program code, xRAGE is organized as follows. Section I provides a brief introduction on the kinetic theory which underpins plasma viscosity, and Section II describes how plasma kinetic theory can be used to calculate plasma viscosity coefficients accurate within the hydrodynamic limit. Section III describes the existing model for calculating the plasma viscosity coefficient in xRAGE. Next, Section IV shows tests of the xRAGE viscosity model against established hydrodynamic theory in the case of binary and trinary plasma mixtures.
Two comparisons between Seasat-A satellite scatterometer (SASS) data and surface truth, obtained from the Gulf of Alaska Seasat Experiment and the Joint Air-Sea Interaction program, have been made to determine the behavior of SASS and its algorithms. The performance of SASS was first evaluated irrespective of the algorithms employed to convert the SASS data to geophysical parameters, which was done by separating the backscatter measurements into small bins of incidence and azimuth angles and polarity and regression against wind speed measurements. The algorithms were then tested by comparing their predicted slopes and y intercepts with those derived from the regressions, and by comparing each SASS backscatter measurement with the backscatter derived from the algorithms, and the given wind velocity from the observations. It was shown that SASS was insensitive to winds at high incidence angles for horizontal polarizations. Fairly high correlations were found between backscatter and wind speeds. The algorithms functioned well at mid-ranges of incidence angle and backscattering coefficient.
The reliability and accuracy of the numerical code for spin up flows in a cylinder by comparing the numerical results against high resolution laser Doppler velocimeter (LDV) measurements of the azimuthal flows were checked. A computer code to generate numerical solution for axisymmetric rotating fluid in a cylinder was obtained and amended for routine use at MSFC. The numerical simulations used the Navier-Stokes equations in axisymmetric form and employed finite difference techniques on both constant and variable grids. The numerical solutions are analyzed to gain further insight into the fundamental questions analyzed in rotating fluid dynamics.
Three liquid coatings and four films that might improve and/or maintain the smoothness of transport aircraft surfaces are considered. Laboratory tests were performed on the liquid coatings (elastomeric polyurethanes) exposed to synthetic type hydraulic fluid, with and without a protective topcoat. Results were analyzed of a 14-month flight service evaluation of coatings applied to leading edges of an airline 727. Two additional airline service evaluations were initiated. Labortory tests were conducted on the films, bonded to aluminum substrate with various adhesives, to determine the best film/adhesive combinations. A cost/benefits analysis was performed and recommendations made for future work toward the application of this technology to commercial transports.
The merits of propulsion system development testing are discussed. The existing data base of technical reports and specialists is utilized in this investigation. The study encompassed a review of all available test reports of propulsion system development testing for the Saturn stages, the Titan stages, and the Space Shuttle main propulsion system. The knowledge on propulsion system development and system testing available from specialists and managers was also 'tapped' for inclusion.
Explore the source record for details and available documents.
Buoyancy-driven turbulent nuclear combustion determines the rate of nuclear burning during the deflagration phase (i.e., the ordinary nuclear flame phase) of Type 1a supernovae, and hence the amount of nuclear energy released during this phase. It therefore determines the amount the white dwarf star expands prior to initiation of a detonation wave, and so the amount of radioactive nickel and thus the peak luminosity of the explosion. However, this key physical process is not fully understood. To better understand this process, the Flash Center has conducted an extensive series of large-scale 3D simulations of buoyancy-driven turbulent nuclear combustion for three different physical situations. This movie shows the results for some of these simulations. Credits: Science: Ray Bair, Katherine Riley, Argonne National Laboratory; Anshu Dubey, Don Lamb, Dongwook Lee, University of Chicago; Robert Fisher, University of Massachusetts at Dartmouth and Dean Townsley, University of Alabama Visualization: Jonathan Gallagher, University of Chicago; Randy Hudson, John Norris and Michael E. Papka, Argonne National Laboratory/University of Chicago
This paper presents a numerical benchmark study of wave propagation due to a paddle motion using different high-fidelity numerical models, which are capable of replicating the nearly actual physical wave tank testing. A full time series of the measured wave generation paddle motion which was used to generate wave propagation in the physical wave tank will be utilized in each of the models contributed by IEA OES Task 10's participants, which includes both computational fluid dynamics (CFD) and smooth hydrodynamic particle (SPH). The high-fidelity simulations of the physical wave testcase will allow for the evaluation of the initial transient effects from wave ramp-up and its evolution in the wave tank over time for two representative regular waves with varying levels of nonlinearity. A couple of interesting metrics like the predicted wave surface elevation at select wave probes, wave period, and phase-shift in time will be assessed to evaluate the relative accuracy of numerical models versus experimental data within specified time intervals. These models will serve as a guide for modelers in the wave energy community and provide a base case to allow further and more detailed numerical modeling of the fixed Kramer Sphere Cases under wave excitation force wave tank testing.
Results are summarized of the simulation verification techniques study which consisted of two tasks: to develop techniques for simulator hardware checkout and to develop techniques for simulation performance verification (validation). The hardware verification task involved definition of simulation hardware (hardware units and integrated simulator configurations), survey of current hardware self-test techniques, and definition of hardware and software techniques for checkout of simulator subsystems. The performance verification task included definition of simulation performance parameters (and critical performance parameters), definition of methods for establishing standards of performance (sources of reference data or validation), and definition of methods for validating performance. Both major tasks included definition of verification software and assessment of verification data base impact. An annotated bibliography of all documents generated during this study is provided.
This paper presents the results of Reynolds-averaged Navier-Stokes (RANS) simulations conducted by NASA’s flow solver, mixed-element USM3D (USM3D-ME), for the 5th AIAA High-Lift Prediction Workshop. As part of the Fixed-Grid RANS Technology Focus Group (TFG), these simulations were performed to assess the accuracy and efficiency of the USM3D-ME solutions in predicting high-lift flows. The High-Lift Common Research Model (CRM-HL) served as the primary geometry. Several CRM-HL configurations were used for three case studies: a verification study (Case 1), a configuration buildup study (Case 2), and a Reynolds-number variation study (Case 3). Overall, USM3D-ME RANS results aligned with the solutions selected by the Fixed-Grid RANS TFG and available wind tunnel data Simulations for Cases 1 and Configuration 2.1 achieved machine-zero residual convergence, with aerodynamic coefficients converging to steady-state values. However, Configurations 2.2-2.4 and Case 3 encountered iterative- and grid-convergence challenges, particularly at high angles of attack. Compared with the experimental data available for Configurations 2.2-2.4, close agreement was demonstrated at low angles of attack. However, for angles of attack approaching the maximum lift conditions, the predicted lift coefficient and pitching moment deviated from experimental values. The drag-coefficient predictions were in a relatively good agreement, however, slight overpredictions were observed at the highest angle of attack corresponding to the maximum-lift condition. Although iterative convergence for Configurations 2.2-2.4 at high angles of attack remains a persistent challenge, averaging aerodynamic coefficients over the last 5000 iterations yielded satisfactory agreement with the available wind tunnel experimental data. During the workshop, the lack of iterative convergence was attributed to the vortex structures emanating from the slat brackets. To investigate this issue further, post-workshop simulations were conducted on Configuration 2.2. In one study, RANS simulations were performed on a simplified geometry with the slat brackets removed. The second study focused on performing URANS simulations on the original Configuration 2.2 geometry. Preliminary results from both studies are presented and compared with wind tunnel data for Configuration 2.2. Consistent with the findings of other participants in the Fixed-Grid RANS TFG, this study emphasizes the necessity for further exploration and advancement in RANS technology for predicting high-lift flows.
This paper presents the results of Reynolds-averaged Navier-Stokes (RANS) simulations conducted by the NASA flow solver, mixed-element USM3D (USM3D-ME), for the 5th AIAA High-Lift Prediction Workshop. As part of the Fixed-Grid RANS Technology Focus Group (TFG), these simulations were performed to assess the accuracy and efficiency of the USM3D-ME solutions in predicting high-lift flows. The High-Lift Common Research Model (CRM-HL) served as the primary geometry. Several CRM-HL configurations were used for three case studies: a verification study (Case 1), a configuration buildup study (Case 2), and a Reynolds-number variation study (Case 3). Overall, USM3D-ME RANS results aligned with the solutions selected by the Fixed-Grid RANS TFG and available wind tunnel data. Simulations for Case 1 and Configuration 2.1 achieved machine-zero residual convergence, with aerodynamic coefficients converging to steady-state values. However, Configurations 2.2-2.4 and Case 3 encountered iterative- and grid-convergence challenges, particularly at high angles of attack. Compared with the experimental data available for Configurations 2.2-2.4, close agreement was demonstrated at low angles of attack. However, for angles of attack approaching the maximum lift conditions, the predicted lift coefficient and pitching moment deviated from experimental values. The drag-coefficient predictions were in relatively good agreement, however, slight overpredictions were observed at the highest angle of attack corresponding to the maximum-lift condition. Although iterative convergence for Configurations 2.2-2.4 at high angles of attack remains a persistent challenge, averaging aerodynamic coefficients over the last 5000 iterations yielded satisfactory agreement with the available wind tunnel experimental data. During the workshop, the lack of iterative convergence was attributed to the vortex structures emanating from the slat brackets. To investigate this issue further, post-workshop simulations were conducted on Configuration 2.2. In one study, RANS simulations were performed on a simplified geometry with the slat brackets removed. The second study focused on performing unsteady RANS (URANS) simulations on the original Configuration 2.2 geometry. Preliminary results from both studies are presented and compared with wind tunnel data for Configuration 2.2. Consistent with the findings of other participants in the Fixed-Grid RANS TFG, this study emphasizes the necessity for further exploration and advancement in RANS technology for predicting high-lift flows.
The need for a structural dynamics verification facility to support structures programs was studied. Most of the industry operated facilities are used for highly focused research, component development, and problem solving, and are not used for the generic understanding of the coupled dynamic response of major engine subsystems. Capabilities for the proposed facility include: the ability to both excite and measure coupled structural dynamic response of elastic blades on elastic shafting, the mechanical simulation of various dynamical loadings representative of those seen in operating engines, and the measurement of engine dynamic deflections and interface forces caused by alternative engine mounting configurations and compliances.
The technical analysis is reported that was performed during the shuttle payload interface verification equipment study. It describes: (1) the background and intent of the study; (2) study approach and philosophy covering all facets of shuttle payload/cargo integration; (3)shuttle payload integration requirements; (4) preliminary design of the horizontal IVE; (5) vertical IVE concept; and (6) IVE program development plans, schedule and cost. Also included is a payload integration analysis task to identify potential uses in addition to payload interface verification.
Many nuclear fuel cycle simulators can analyze transitions from once-through to advanced nuclear fuel cycles. Verification studies compare various fuel cycle analysis tools to test agreement and identify sources of difference. A recent verification study, Feng et al. (2016) established transition scenario test case specifications and accordingly evaluated national laboratory nuclear fuel cycle simulators, DYMOND, VISION, ORION, and MARKAL. This work verifies the performance of C YCLUS , the agent-based, open-source fuel cycle simulator, using the test case specifications in Feng et. al. We report, C YCLUS demonstrates agreement with the results from the previous verification study. Minor differences reflect intentional, detailed material tracking in the C YCAMORE reactor module. These results extend the example results in Feng et al. to further enable future verification of additional nuclear fuel cycle simulation tools.
Appendices to the shuttle payload integration study provide for: (1) The interface verification equipment hardware utilization list; (2) the horizontal IVE in-field assembly procedure; and (3) payload integration baseline functional flow block diagrams and options.
This work reports the first step in such an analysis, the verification of isotope removal capability for multi-region MSR depletion in Griffin. Verification studies are performed against SERPENT for chemical species removal from the core to an off-gas system for MSR analysis. A brief review of the Bateman equations including the isotopic removal term is provided along with a description of the example problem used in the verification studies performed in Griffin versus SERPENT. Next, the results of the verification study are presented for isotopic depletion, isotopic depletion with removal, and the specific analysis case of varying the solubility of Iodine in a salt system and how this can affect material buildup in the off-gas system. Lastly, the results are analyzed and future work detailing the fully coupled MSR depletion analysis that incorporates the true multiphysics of the system is discussed.