Search NASA⌕ Search

SEARCH · Search NASA

Results for “W component of wind velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2

An analysis of spanwise gust gradient data

Plots of winds encountered during flight are presented for severe turbulence cases from flights 6 and 7 of the Joint Airport Weather Studies (JAWS) Project (McCarthy et al., 1982). During run 10 of flight 7, analyzed here in considerable detail, the B-57B Cambera aircraft showed a sharp increase in airspeed of 15 m/sec over a distance of about 130 m and then a more gradual decrease of 20 to 25 m/sec over a distance of about 2 km. This suspected outflow feature was associated with a downdraft exceeding 10 m/sec. The horizontal wind direction changed nearly 180 deg during the pass through the feature. Unexpectedly, the intensity of the velocity differences decreased for all three components within the downdraft. Calculated probability density functions for u, v, and w show a jagged character, whereas delta-u, delta-v, and delta-w show a much smoother, unimodal behavior. The distributions for delta-u, delta-v, and delta-w are distinctly non-Gaussian.

Campbell, W.↗

The Adelaide VHF radar: Capabilities and future plans

The VHF radar at Buckland Park, South Australia commenced operation in January, 1984. The radar is located adjacent to the 2-MHz ionospheric radar. The routine method for measuring horizontal wind velocity is the space antenna technique (SA) while the Doppler technique is used to measure vertical velocities. It is possible to swing the transmitting beam in the east-west plane, allowing Doppler measurements of the EW wind component.

Briggs, B. H.↗

The winds of O-stars. II - The terminal velocities of stellar winds of O-type stars

The SEI method (Lamers et al., 1987) is used to obtain P Cygni profiles of the UV resonance lines of C IV, N V, and S IV and of the subordinate UV lines of N IV and C III observed in the spectra of 27 O-type stars. Theoretical profiles which include the turbulence effects agree well with the observations, and they can account for the deep absorption troughs, the shape of the violet absorption wings, and the wavelength of the emission peak. The resulting terminal velocities of the stellar winds are found to be systematically lower by about 400 km/s than previous estimates obtained using the Sobolev approximation (Castor and Lamers, 1979), suggesting that the narrow absorption components, observed in the UV resonance lines of O and B stars, reach the terminal velocity of the winds.

Groenewegen, M. A. T.↗

Wave Driven Exothermic Heating in the Mesopause Region

A full-wave propagation model was developed that describes the propagation of gravity waves from the Earth's surface to the upper boundary, which can be placed anywhere between 150 and 500 km altitude. The model includes a realistic background atmosphere, and includes the effects of mean horizontal winds and their vertical shears, mean vertical temperature gradients, the eddy and molecular diffusion of heat and momentum, and the effects of ion-drag. This model solves five coupled second-order differential equations (continuity, momentum, and energy) in the vertical coordinate to derive the perturbation variables u', v', w' (horizontal and vertical velocity components), T' (temperature) and p' (pressure). The upper boundary can be automatically selected based on tests using the radiation condition at the upper boundary, wherein the height is increased until the wave is experiencing severe dissipation at the upper boundary, ensuring that substantial absorption occurs for any waves reflected from the upper boundary. The determination of wave amplitude is a key requirement of wave energetics. Therefore, the fullwave model has been applied to airglow observations in order to determine wave amplitudes as a function of altitude. This was accomplished by using the full-wave model output to drive a chemistry perturbation module that describes minor species perturbations and the resulting airglow perturbations. The full-wave output was multiplied by an altitude-independent factor such that the modeled and observed relative airglow intensity perturbations were equal. The effects of mean winds were included in these studies, and found to be the most important model input affecting the calculations (being more important than the choice of eddy diffusion profiles and chemical kinetic coefficients). In one study (Hickey et al., 1997a) these winds could not be well estimated from the measurements, whereas in the second study (Hickey et al.,1997b) the mean were well defined with a sodium wind-temperature lidar.

Hickey, Michael P.↗

The cold solar wind

From 3 to 10 percent of the time, the solar wind has a radial proton temperature between 15,000 K and 3500 K (the lowest recorded temperature). This 'cold' component shows some very important features that make it worthy of special study. It shows a temperature dependence on helicentric distance that is nearly adiabatic. When extrapolated back to 3 R(s), assuming adiabatic cooling, the resulting temperature for this cold component is in good agreement with coronal temperatures near the sonic point. Most importantly, the proton velocities and densities associated with this cold component match those predicted by solar wind models that do not incorporate significant wave heating. It is concluded that this is one solar wind component that fits well with appropriate models.

Freeman, J. W.↗

Experiments on transonic and supersonic turbulent boundary-layer separation

Results of experimental investigations into turbulent boundary-layer behavior under the influence of pressure gradients and with separation are presented for transonic and supersonic flow fields. In the transonic case, an axisymmetric model was implemented consisting of an annular circular arc bump affixed to a circular cylinder aligned with the flow direction. For the supersonic separation study, an oblique shock wave impinging on the wind tunnel wall boundary layer was employed to cause separation. The mean streamwise and normal velocity components as well as the respective turbulence intensities were obtained with a two-color frequency shifted laser velocimeter.

Bachalo, W. D.↗

Wind sensitivity studies of a non-return wind tunnel with a 216- by 432-mm (8.5- by 17.0-inches) test section, phase 2

The refinement of inlet and exit treatments were studied which would minimize the effect of external wind on the test-section flow quality of a nonreturn wind tunnel. The investigation was conducted in the Ames Research Center 40- by 80-foot Wind Tunnel which served as the wind source. Several inlets and two exits were tested at wind directions ranging from 0 to 180 degrees and at wind-to-test-section velocity ratios from zero to somewhat greater than one. For the best inlet configuration the flow quality was good, with a velocity deviation in each of the three component directions generally less. The loss in total pressure due to the inlet treatment was low: about 0.035 of the test-section dynamic pressure for the no-wind case.

Eckert, W. T.↗

The internal plasma state of the high speed solar wind at 1 AU

The character of particle velocity distributions in the high speed solar wind is described. It is found that electron distribution shapes differ from simple bi-Maxwellians in that a hot strongly beamed high energy electron component is always present, and is observed to move relative to a distinct low energy electron component along the magnetic field direction away from the sun. The velocity difference between hot and cold electron components appears, at times, to be strongly correlated with the local Alfven speed. Proton velocity distributions are also best represented by two relatively convecting unresolved components. Evidence is presented which supports the idea that the two-component proton structure observed in high speed regions is intimately related to fine scale velocity variations at 1 AU, and probably to prominent spatial and/or temporal structures present throughout that part of the corona from which the solar wind evolves.

Feldman, W. C.↗

A Suzaku X-ray Observation of One Orbit of the Supergiant Fast X-ray Transient IGR J16479-4514

We report on a 250 ks long X-ray observation of the supergiant fast X-ray transient (SFXT) IGR J16479-4514 performed with Suzaku in 2012 February. During this observation, about 80% of the short orbital period (P(sub orb) approximates 3.32 days) was covered as continuously as possible for the first time. The source light curve displays variability of more than two orders of magnitude, starting with a very low emission state (10(exp −13) erg / sq cm/s; 1-10 keV) lasting the first 46 ks, consistent with being due to the X-ray eclipse by the supergiant companion. The transition to the uneclipsed X-ray emission is energy dependent. Outside the eclipse, the source spends most of the time at a level of 6-7X10)(exp−12) erg/sq. cm/s) punctuated by two structured faint flares with a duration of about 10 and 15 ks, respectively, reaching a peak flux of 3-4X10(exp −11) erg/sq. cm./S, separated by about 0.2 in orbital phase. Remarkably, the first faint flare occurs at a similar orbital phase of the bright flares previously observed in the system. This indicates the presence of a phase-locked large scale structure in the supergiant wind, driving a higher accretion rate onto the compact object. The average X-ray spectrum is hard and highly absorbed, with a column density, NH, of 10*exp 23)/sq cm, clearly in excess of the interstellar absorption. There is no evidence for variability of the absorbing column density, except that during the eclipse, where a less absorbed X-ray spectrum is observed. A narrow Fe K-alpha emission line at 6.4 keV is viewed along the whole orbit, with an intensity which correlates with the continuum emission above 7 keV. The scattered component visible during the X-ray eclipse allowed us to directly probe the wind density at the orbital separation, resulting in rho(sub w)=7X10(exp −14) g/cubic cm. Assuming a spherical geometry for the supergiant wind, the derived wind density translates into a ratio M(sub w)/v(sub infinity) = 7X10(exp −17) Solar M/km which, assuming terminal velocities in a large range 500-3000 km/s, implies an accretion luminosity two orders of magnitude higher than that observed. As a consequence, a mechanism should be at work reducing the mass accretion rate. Different possibilities are discussed.

J164794514↗

Low-velocity variability in the stellar wind of HD 152408 (O8: Iafpe)

We describe high-quality, spectroscopic time series observations of variability at low velocities in the stellar wind of the extreme O-supergiant HD 152408. These observations were obtained during a monitoring campaign coordinated between Australia and Chile in 1992 July. Systematic variability on hourly time scales is particularly apparent in the He I lambda 5876 P Cygni profile, which diagnoses the deeper, denser region of the wind. These changes indicate the presence of evolving wind structure, which takes the form of blueward-migrating, discrete optical depth enhancements. Four distinct features are identified over approximately 5 days, spanning a velocity range of about -50 km/s at formation to about -500 km/s (i.e., greater than or approximately equal to 0.5 of the terminal velocity) at the blue edge of the He I absorption trough. Sympathetic variations are also apparent in the Balmer emission lines of HD 152408. The characteristics of these features, including their widths, column densities, and accelerations, suggest similarities to discrete absorption components commonly seen at larger velocities in UV P Cygni profiles of other O-type stars. These optical results demonstrate that frequent, systematic wind variability is present down to very large depths, and provide constraints on the stability of the low-velocity regime of hot-star winds.

Prinja, Raman K.↗

Aircraft liftmeter

A display for aiding the pilot of an aircraft in anomalous wind environments is described. Wind velocity components are measured by an instrument, processed by a computer and a vector generator, and then displayed as a vector. The display utilizes the measurements of ground speed and of wind velocity in three mutually perpendicular directions. This display will also show changes in lift of an aircraft.

Millen, E. W.↗

Non-planar MHD model for solar flare-generated disturbances in the heliospheric equatorial plane

An analysis, with a representative (canonical) example of solar-flare-generated equatorial disturbances, is made for the temporal and spatial changes in the solar wind plasma and magnetic field environment between the sun and 1 AU. The goal is to search for first-order global consequences rather than to make a parametric study. The analysis treats all three plasma velocity and magnetic field components in any convenient heliospheric plane of symmetry. The representative disturbance is examined for the canonical case in which the temporal and spatial changes in a homogeneous solar wind caused by a solar-flare-generated shock wave are described. All plasma and field parameters at three radial locations are examined. These are the central meridian and 33 deg W and 90 deg W of the flare's central meridian. It is found that the incorporation of a small meridional magnetic field in the ambient magnetic spiral field has negligible effect on the results. The magnetic field exhibits strong kinking within the interplanetary shocked flow, even reversed polarity that, coupled with low temperature and low density, suggests a plausible explanation for magnetic clouds' with accompanying double-streaming of electrons observed at directions approximately 90 deg to the heliocentric radius.

Wu, S. T.↗

Application of a single laser Doppler system to the measurement of atmospheric winds

The feasibility of employing a single laser Doppler velocimeter (LDV) system to remotely measure one-, two-, and three-dimensional velocity components in atmospheric flow fields is presented. A focused continuous wave CO2 laser emitting at the 10.6 mu wavelength is used as the laser source. Scan configurations employed by the LDV system were single-point, two-point, conical, and spiral conical. Test results are presented, which include favorable comparisons of velocity components measured by conventional anemometry and the LDV system. The feasibility using a single-beam LDV employing a conical scan technique for measuring two- and three-dimensional mean winds. Measurements to 300 m in dense fogs showed the ability of the LDV system to operate in dense fogs.

Cliff, W. C.↗

The Effects of Clumping on Wind Line Variability

We review the effects of clumping on the profiles of resonance doublets. By allowing the ratio of the doublet oscillator strengths to be a free parameter, we demonstrate that doublet profiles contain more information than is normally utilized. In clumped (or porous) winds, this ratio can lie between unity and the ratio of the f-values, and can change as a function of velocity and time, depending on the fraction of the stellar disk that is covered by material moving at a particular velocity at a given moment. Using these insights, we present the results of SEI modeling of a sample of B supergiants, sigma Pup and a time series for a star whose terminal velocity is low enough to make the components of its Si VI lambda lambda 1400 independent. These results are interpreted within the framework of the Oskinova et al. (2007) model, and demonstrate how the doublet profiles can be used to extract information about wind structure.

Prinja, R. K.↗

Remote measurement of the transverse wind velocity component using a laser Doppler velocimeter

The wind speed transverse to the line-of-sight of a laser Doppler radar has been measured using the intensity fluctuations of the returned signal. These measurements were made at a range of 100 m with a CO2 CW laser Doppler velocimeter, which was simultaneously performing its design function of determining the radial velocity component. The transverse component measurements are compared with those obtained using a u, v, w Gill propeller anemometer.

Kennedy, L. Z.↗

Optical observations of thermospheric dynamics at Arecibo

A description is given of wind and temperature data obtained with a 15-cm Fabry-Perot interferometer. The observations were made between February and August 1980 and confirm the details of the conceptual model of Herrero and Meriwether (1980). Attention is given to the method used to analyze the neutral wind field, the zonal winds, the meridional wind, the horizontal wind gradient, the vertical wind velocity, the full wind field, and the neutral temperature. The most regular feature of the neutral wind at Arecibo is the zonal component, which has a peak velocity in the eastward direction near sunset, and decreases in velocity as the night progresses. Both the wind and temperature measurements reported provide ample confirmation of the importance of the equatorial midnight pressure bulge in modifying the dynamic behavior of the nighttime thermosphere at Arecibo.

Burnside, R. G.↗

Atmospheric turbulence parameters for modeling wind turbine dynamics

A model which can be used to predict the response of wind turbines to atmospheric turbulence is given. The model was developed using linearized aerodynamics for a three-bladed rotor and accounts for three turbulent velocity components as well as velocity gradients across the rotor disk. Typical response power spectral densities are shown. The system response depends critically on three wind and turbulence parameters, and models are presented to predict desired response statistics. An equation error method, which can be used to estimate the required parameters from field data, is also presented.

Holley, W. E.↗

A method for the measurement and the statistical analysis of atmospheric turbulence

The instantaneous values of output voltages representing the wind velocity vector and the temperature at different elevations of the 250-foot meteorological tower located at NASA Wallops Flight Center are provided with the three dimensional split-film TSI Model 1080 anemometer system. The output voltages are sampled at a rate of one every 5 milliseconds, digitized and stored on digital magnetic tapes for a time period of approximately 40 minutes, with the use of a specially designed data acqusition system. A new calibration procedure permits the conversion of the digital voltages to the respective values of the temperature and the velocity components in a Cartesian coordinate system connected with the TSI probe with considerable accuracy. Power, cross, coincidence and quadrature spectra of the wind components and the temperature are obtained with the use of the fast Fourier transform. The cosine taper data window and ensemble and frequency smoothing techniques are used to provide smooth estimates of the spectral functions.

Tieleman, H. W.↗