Search NASA⌕ Search

SEARCH · Search NASA

Results for “WALLS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

The performance of smooth-wall drag reducing outer-layer devices in rough-wall boundary layers

The boundary layer drag on a 0.28 m x 0.91 m flat-plate was measured to evaluate the performance of smooth-wall drag reducing outer-layer devices in rough-wall boundary layers up to a chord Reynolds number, Re(c) of 17,000. The devices were a pair of thin flat ribbons placed in tandem. The wall conditions examined were smooth, transverse-groove roughnesses having cavity width/depth ratios of 0.7 (d-type) and 3 (k-type), and sandpaper roughness (k-type) of grit sizes 180, 50 and 36. The area-averaged wall-drag was reduced compared to the respective normal levels for all wall conditions. All k-type rough walls exhibited a comparable level of drag reduction (about 7 percent) which was lower than that in the smooth-wall. The d-type rough-wall exhibited a transitional behavior in that the drag reduction dropped from the smooth-wall level to that of the k-type roughnesses with increase in the flow speed. In further experiments on a 6 meter long sandpaper roughened wall and with a pair of symmetric airfoil devices in tandem at an Re(c) of 77,500, it was possible to recover the device drag penalty fully, but no net drag reduction was achieved. The apparent loss of performance of the devices in a rough-wall is explained in terms of their inability to alter the pressure component of the drag in a significant way.

Bandyopadhyay, P. R.↗
NASA NTRS1989

Comparison of airfoil results from an adaptive wall test section and a porous wall test section

Two wind tunnel investigations were conducted to assess two different wall interference alleviation/correction techniques: adaptive test section walls and classical analytical corrections. The same airfoil model has been tested in the adaptive wall test section of the NASA-Langley 0.3 m Transonic Cryogenic Tunnel (TCT) and in the National Aeronautical Establishment (NAE) High Reynolds Number 2-D facility. The model has a 9 in. chord and a CAST 10-2/DOA 2 airfoil section. The 0.3 m TCT adaptive wall test section has four solid walls with flexible top and bottom walls. The NAE test section has porous top and bottom walls and solid side walls. The aerodynamic results corrected for top and bottom wall interference at Mach numbers from 0.3 to 0.8 at a Reynolds number of 10 by 1,000,000. Movement of the adaptive walls was used to alleviate the top and bottom wall interference in the test results from the NASA tunnel.

Mineck, Raymond E.↗
NASA NTRS1975

Experimental investigation of wall shock cancellation and reduction of wall interference in transonic testing

A series of experiments were performed to evaluate the effectiveness of a three-dimensional land and groove wall geometry and a variable permeability distribution to reduce the interference produced by the porous walls of a supercritical transonic test section. The three-dimensional wall geometry was found to diffuse the pressure perturbations caused by small local mismatches in wall porosity permitting the use of a relatively coarse wall porosity control to reduce or eliminate wall interference effects. The wall porosity distribution required was found to be a sensitive function of Mach number requiring that the Mach number repeatability characteristics of the test apparatus be quite good. The effectiveness of a variable porosity wall is greatest in the upstream region of the test section where the pressure differences across the wall are largest. An effective variable porosity wall in the down stream region of the test section requires the use of a slightly convergent test section geometry.

Ferri, A.↗
DOE OSTI2017

Nanoscale movements of cellulose microfibrils in primary cell walls

The growing plant cell wall is commonly considered to be a fibre-reinforced structure whose strength, extensibility and anisotropy depend on the orientation of crystalline cellulose microfibrils, their bonding to the polysaccharide matrix and matrix viscoelasticity. Structural reinforcement of the wall by stiff cellulose microfibrils is central to contemporary models of plant growth, mechanics and meristem dynamics. Although passive microfibril reorientation during wall extension has been inferred from theory and from bulk measurements, nanometre-scale movements of individual microfibrils have not been directly observed. For this, we combined nanometre-scale imaging of wet cell walls by atomic force microscopy (AFM) with a stretching device and endoglucanase treatment that induces wall stress relaxation and creep, mimicking wall behaviours during cell growth. Microfibril movements during forced mechanical extensions differ from those during creep of the enzymatically loosened wall. In addition to passive angular reorientation, we observed a diverse repertoire of microfibril movements that reveal the spatial scale of molecular connections between microfibrils. Our results show that wall loosening alters microfibril connectivity, enabling microfibril dynamics not seen during mechanical stretch. These insights into microfibril movements and connectivities need to be incorporated into refined models of plant cell wall structure, growth and morphogenesis.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Enhancement of magnetic domain wall velocity via resonant dissipation of standing wave modes of domain wall structure with perpendicular magnetic anisotropy

The dynamic behaviors of magnetic domain walls have significant implications for developing advanced spintronic devices. In this study, we investigate the intriguing resonance phenomenon within the magnetic domain wall structure, focusing on the dissipation mechanism and its impact on domain wall dynamic motion. By applying a static external magnetic field, we observe a remarkable amplification of domain wall velocity through the resonant excitations of the flexure modes. The resonance of the flexure mode exerts an indirect influence on the domain wall velocity through energy dissipation, leading to a significant enhancement from the predictions of the one-dimensional Walker model. We establish a robust model platform rooted in energy dissipation allows comprehensive understanding the dramatic enhancement of domain wall velocity observed during width-directional flexure mode resonance. By directly quantifying energy dissipation, our approach provides highly effective and accurate estimates of domain wall velocity, surpassing previous methods that focus solely on the instantaneous dynamics of the domain wall structure. These findings offer crucial insights into the fundamental mechanisms governing the dynamics of domain walls and other magnetic systems, such as magnetic skyrmions, bubbles, and magnetic vortices, paving the way for development and optimization of next-generation spintronic devices.

Collective dynamics↗
DOE OSTI2024

IX Cell Wall Research Conference 2022 (IXCWRC): Cell wall research for new fundamental discoveries and applications in plant biology

This application is for securing funds to offset the registration fees and lodging costs for US-based early career investigators (ERCs) to participate to the IX Cell Wall Research Conference 2022 (IXCWRC 2022): Cell wall research for new fundamental discoveries and applications in plant biology. The conference will be held in East Lansing, Michigan on June 13-17, 2022. The conference will focus on the plant cell wall. Plant cells are encapsulated by the cell wall, a dynamic structure that protects them, enables them to interface with the external environment and supports the growth of the entire organism. There is a growing interest in understanding the complex processes necessary to build and deconstruct the plant cell wall. A better understanding of how the cell wall is synthesized during plant growth and in response to the environment, and how it is deconstructed for a broad variety of applications can inform and improve biotechnological processes for increasing biomass yield and improving industrial processes for the recovery of valuable, sustainable polymers. Acquiring such knowledge requires the exchange of new ideas and results as well as the development and application of new technologies. The IXCWRC 2022 aims to reach this goal by providing an opportunity for an open forum to discuss new ideas and theories and develop collaborations for scientists across the globe in a diverse and supportive environment. A distinction of the IXCWRC 2022 from all the preceding plant cell wall conferences will be its focus on the training and inclusion of the next generation of scientists, the ERCs. The overall goal of this application is to broaden the participation of ERCs with a focus on underrepresented communities. The specific goal of this application is to secure support for registration and lodging for US-based ERCs to attend the conference. Priority will be given to ERCs from underrepresented communities in science. We expect that support from DOE will allow the development of an exciting and innovative program to discuss the latest scientific advances in cell wall biology research, advance the next generation of plant cell wall researchers and foster the foundations of an inclusive community in science.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2017

Evaluating the Thermal Performance of Mass Walls Compared to Wood-Framed and Steel-Framed Walls in Residential Buildings using EnergyPlus

While homes across the United States are traditionally built using wood-frame construction, mass or concrete walls are popular in certain regions of the country. While, mass walls have certain obvious advantages in terms of energy efficiency compared to the lighter wood-frame or steel-frame walls, conducting hotbox tests and specialized thermal modelling analyses of these walls to evaluate energy performance is often time-consuming and cost-prohibitive. More importantly, heat transfer in real buildings is a dynamic process consisting of the effects of outdoor air temperature and solar gains in conjunction with infiltration and internal gains. These are not captured through isolated hotbox tests or modelling techniques. The latest state-of-art building energy simulation tools can be utilized to overcome these constraints. This paper describes a comprehensive analysis of different wall types using EnergyPlus. The methodology for modelling various wood, steel and mass walls and the development of material properties for use in simulation is described. An overview of the large-scale simulation structure used in the analysis is provided. Resulting energy consumption for various mass walls is included along with a comparison of select mass walls and wood-frame or steel-frame walls.

Mass walls, Large-scale simulation, residential bu↗
DOE OSTI2019

Analyzing the post-contrast attenuation of the esophageal wall on routine contrast-enhanced MDCT examination can improve the diagnostic accuracy in response evaluation of the squamous cell esophageal carcinoma to neoadjuvant chemoradiotherapy in comparison with the esophageal wall thickness

Purpose: To evaluate the accuracy of the multidetector computed tomography (MDCT) in the response evaluation of the esophageal squamous cell carcinoma (ESCC) to neoadjuvant chemoradiotherapy (nCRT) by analyzing the thickness and post-contrast attenuation of the esophageal wall after the nCRT. Methods: Contrast-enhanced (CE)-MDCT examinations in portal venous phase of one hundred patients with locally advanced ESCC who received nCRT and underwent esophageal resection and histopathology assessment of tumor regression grade (TRG) were retrospectively analyzed by measuring the maximal thickness and mean density of the esophageal wall in the segment involved by tumor and visually searching for hyperdense foci within it. Diagnostic performance was evaluated using the ROC analysis. Results: Average attenuation of the esophageal wall had stronger diagnostic performance for predicting pathologic complete regression (pCR) (AUC = 0.994; p < 0.001) in relation to maximal esophageal wall thickness (AUC = 0.731; p < 0.001). Maximal esophageal wall thickness ≤ 9 mm and average attenuation of the esophageal wall ≤ 64 HU predicted pCR with the sensitivity, specificity, and overall accuracy of 62.5%, 77.9%, and 73%, and 96.9%, 98.5%, and 98%, respectively. Combination of both cutoff values enabled correct assessment of pCR with the 100% accuracy. Visual detection of the hyperdense focus within the esophageal wall predicted pCR with the sensitivity, specificity, and overall accuracy values of 100%, 94.1%, and 96%, respectively. Conclusion: Visual analysis and measurement of post-contrast attenuation of the esophageal wall after the nCRT can improve diagnostic accuracy of MDCT in the response evaluation of the ESCC to nCRT in comparison with measuring the esophageal wall thickness.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2019

Intrinsic structural instabilities of domain walls driven by gradient coupling: Meandering antiferrodistortive-ferroelectric domain walls in BiFeO 3

Using the Landau-Ginzburg-Devonshire approach, we predict the intrinsic instability of the ferroelectric-ferroelastic domain walls in the multiferroic BiFeO 3 emerging from the interplay between the gradient terms of the antiferrodistortive and ferroelectric order parameters at the walls. These instabilities are the interface analog of the structural instabilities in the vicinity of phase coexistence in the bulk, and so they do not stem from incomplete polarization screening in thin films or its spatial confinement, electrostrictive or flexoelectric coupling. The effect of BiFeO 3 material parameters on the 71°, 109°, and 180° walls is explored, and it is shown that the meandering instability appears at 109° and 180° walls for small gradient energies, and the walls become straight and broaden for higher gradients. In contrast to the 180° and 109° domain walls, uncharged 71° walls are always straight, and their width increases with increasing the tilt gradient coefficient. As a result, the wall instability and associated intrinsic meandering provide insight into the behavior of morphotropic and relaxor materials, wall pinning, and mechanisms of interactions between order parameter fields and local microstructure.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Two- and three-dimensional model and wall data from a flexible-walled transonic test section

Both two- and three-dimensional model testing is being carried out in the transonic flexible-walled wind tunnel test section. The test section has flexible top and bottom walls with rigid sidewalls. Interference is eliminated by adjustments based on data taken at walls in two dimensional models. Cast-7 data will illustrate agreement between various flexible-walled tunnels. In three-dimensional models interference cannot be eliminated but wall adjustments can control and relieve the principal sources of wall-induced errors. Estimates of magnitudes of the control which may be exercised on flow by movement of one wall jack are presented. A wall control algorithm (still in analytic development stage) based on use of this data is described. Brief examples of control of wall-induced perturbations in region of model are given.

Goodyer, M. J.↗
NASA NTRS1988

Adaptive wall technology for minimization of wall interferences in transonic wind tunnels

Modern experimental techniques to improve free air simulations in transonic wind tunnels by use of adaptive wall technology are reviewed. Considered are the significant advantages of adaptive wall testing techniques with respect to wall interferences, Reynolds number, tunnel drive power, and flow quality. The application of these testing techniques relies on making the test section boundaries adjustable and using a rapid wall adjustment procedure. A historical overview shows how the disjointed development of these testing techniques, since 1938, is closely linked to available computer support. An overview of Adaptive Wall Test Section (AWTS) designs shows a preference for use of relatively simple designs with solid adaptive walls in 2- and 3-D testing. Operational aspects of AWTS's are discussed with regard to production type operation where adaptive wall adjustments need to be quick. Both 2- and 3-D data are presented to illustrate the quality of AWTS data over the transonic speed range. Adaptive wall technology is available for general use in 2-D testing, even in cryogenic wind tunnels. In 3-D testing, more refinement of the adaptive wall testing techniques is required before more widespread use can be planned.

Wolf, Stephen W. D.↗
NASA NTRS1989

A two-dimensional adaptive-wall test section with ventilated walls in the Ames 2- by 2-foot transonic wind tunnel

The first tests conducted in the adaptive-wall test section of the Ames Research Center's 2- by 2-Foot Transonic Wind Tunnel are described. A procedure was demonstrated for reducing wall interference in transonic flow past a two-dimensional airfoil by actively controlling flow through the slotted walls of the test section. Flow through the walls was controlled by adjusting pressures in compartments of plenums above and below the test section. Wall interference was assessed by measuring (with a laser velocimeter) velocity distributions along a contour surrounding the model, and then checking those measurements for their compatibility with free-air far-field boundary conditions. Plenum pressures for minimum wall interference were determined from empirical influence coefficients. An NACA 0012 airfoil was tested at angles of attach of 0 and 2, and at Mach numbers between 0.70 and 0.85. In all cases the wall-setting procedure greatly reduced wall interference. Wall interference, however, was never completely eliminated, primarily because the effect of plenum pressure changes on the velocities along the contour could not be accurately predicted.

Schairer, Edward T.↗
DOE OSTI2016

Wall Area of Influence and Growing Wall Heat Transfer due to Sliding Bubbles in Subcooled Boiling Flow

A variety of dynamical features of sliding bubbles and their impact on wall heat transfer were observed at subcooled flow boiling conditions in a vertical square test channel. Among the wide range of parameters observed, we particularly focus in this paper on (i) the sliding bubbles’ effect on wall heat transfer (supplemantry discussion to the authors’ previous work in Yoo et al. (2016a,b)) and (ii) the wall area influenced by sliding bubbles in subcooled boiling flow. At first, this study reveals that the degree of wall heat transfer improvement due to sliding bubbles depended less on the wall superheat condition as the mass flux increased. Also, the sliding bubble trajectory was found to be one of the critical factors in order to properly describe the wall heat transfer associated with sliding bubbles. In particular, the wall area influenced by sliding bubbles depended strongly on both sliding bubble trajectory and sliding bubble size; the sliding bubble trajectory was also observed to be closely related to the sliding bubble size. Importantly, these results indicate the limitation of current approach in CFD analyses especially for the wall area of bubble influence. In addition, the analyses on the temporal fraction of bubbles’ residence (FR) along the heated wall show that the sliding bubbles typically travel through narrow path with high frequency while the opposite was observed downstream. That is, both FR and sliding bubble trajectory depended substantially on the distance from nucleation site, which is expected to be similar for the quenching heat transfer mode induced by sliding bubbles.

42 ENGINEERING↗
DOE OSTI2018

Finding order in a bustling construction zone: quantitative imaging and analysis of cell wall assembly in plants

Assembly of polysaccharide-based walls by plant cells involves the rapid synthesis, trafficking, and deposition of complex biopolymers, but how these events are controlled and coordinated to achieve a strong, resilient extracellular matrix has remained obscure for decades. Recent quantitative analyses of fluorescence microscopy data have revealed details of the trafficking and synthetic activity of cellulose synthases, and new methods for labeling matrix polymers have unveiled aspects of their regulated deposition in the wall. Detailed studies of the identity, architecture, activity, and trafficking of the proteins and protein complexes that synthesize wall polymers, combined with advances in image acquisition and analysis, will aid future efforts to dissect wall assembly.

biofuels (including algae and biomass), bio-inspir↗
DOE OSTI2016

Domain wall and interphase boundary motion in (1−x)Bi(Mg{sub 0.5}Ti{sub 0.5})O{sub 3}–xPbTiO{sub 3} near the morphotropic phase boundary

Electric field-induced changes in the domain wall motion of (1−x)Bi(Mg{sub 0.5}Ti{sub 0.5})O{sub 3}–xPbTiO{sub 3} (BMT-xPT) near the morphotropic phase boundary (MPB) where x = 0.37 (BMT-37PT) and x = 0.38 (BMT-38PT), are studied by means of synchrotron x-ray diffraction. Through Rietveld analysis and profile fitting, a mixture of coexisting monoclinic (Cm) and tetragonal (P4mm) phases is identified at room temperature. Extrinsic contributions to the property coefficients are evident from electric-field-induced domain wall motion in both the tetragonal and monoclinic phases, as well as through the interphase boundary motion between the two phases. Domain wall motion in the tetragonal and monoclinic phases for BMT-37PT is larger than that of BMT-38PT, possibly due to this composition's closer proximity to the MPB. Increased interphase boundary motion was also observed in BMT-37PT. Lattice strain, which is a function of both intrinsic piezoelectric strain and elastic interactions of the grains (the latter originating from domain wall and interphase boundary motion), is similar for the respective tetragonal and monoclinic phases.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Observation of hohlraum-wall motion with spectrally selective x-ray imaging at the National Ignition Facility

The high fuel capsule compression required for indirect drive inertial confinement fusion requires careful control of the X-ray drive symmetry throughout the laser pulse. When the outer cone beams strike the hohlraum wall, the plasma ablated off the hohlraum wall expands into the hohlraum and can alter both the outer and inner cone beam propagations and hence the X-ray drive symmetry especially at the final stage of the drive pulse. To quantitatively understand the wall motion, we developed a new experimental technique which visualizes the expansion and stagnation of the hohlraum wall plasma. Details of the experiment and the technique of spectrally selective x-ray imaging are discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Domain wall dynamics in tungsten trioxide: Evidence for polar domain walls

Domain walls have distinct properties from the bulk, and tailoring them to suit the needs for device applications is critical. Tungsten trioxide, WO 3 , is of great interest for device applications that make use of domain wall properties; it exhibits a phenomenologically rich sequence of phase transitions, virtually all of which are ferroelastic in character, resulting in many sets of domain walls at low temperatures, each with their own unique properties. Domain wall motion and its contribution to the piezoelectric response have been investigated in WO 3 from 300 to 180 K using resonant ultrasound spectroscopy (RUS) and resonant piezoelectric spectroscopy (RPS), which showed that the P 2 1 / n , P 1 ¯ , and P 2 1 / c phases give a piezoelectric response despite the bulk being nominally centrosymmetric. Second harmonic generation (SHG) confirmed that polarity was strongest within the domain walls, and additional weak signals were found in the domains. Domain wall mobility was investigated in the P b c n , P 2 1 / n , and P 2 1 / c phases from 685 to 5 K. Domain walls in the P 2 1 / n and P 1 ¯ were more mobile than those in the P b c n and P 2 1 / c structures, and soon after the P 1 ¯ → P 2 1 / c transition the walls become pinned at ∼ 140 K . Published by the American Physical Society 2024

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗