Search NASA⌕ Search

SEARCH · Search NASA

Results for “WHISKER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

35 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Anion-tethered Single Lithium-ion Conducting Polyelectrolytes through UV-induced Free Radical Polymerization for Improved Morphological Stability of Lithium Metal Anodes

Single Li + ion conducting polyelectrolytes (SICs), which feature covalently tethered counter-anions along their backbone, have the potential to mitigate dendrite formation by reducing concentration polarization and preventing salt depletion. However, due to their low ionic conductivity and complicated synthetic procedure, the successful validation of these claimed advantages in lithium metal (Li 0 ) anode batteries remains limited. In this study, we fabricated a SIC electrolyte using a single-step UV polymerization approach. The resulting electrolyte exhibited a high Li + transference number (t + ) of 0.85 and demonstrated good Li + conductivity (6.3×10 -5 S/cm at room temperature), which is comparable to that of a benchmark dual ion conductor (DIC, 9.1×10 -5 S/cm). Benefitting from the high transference number of SIC, it displayed a three-fold higher critical current density (2.4 mA/cm 2 ) compared to DIC (0.8 mA/cm 2 ) by successfully suppressing concentration polarization-induced short-circuiting. Additionally, the t + significantly influenced the deposition behavior of Li 0 , with SIC yielding a uniform, compact, and mosaic-like morphology, while the low t + DIC resulted in a porous morphology with Li 0 whiskers. In conclusion, using the SIC electrolyte, Li 0 ||LiFePO 4 cells exhibited stable operation for 4500 cycles with 70.5 % capacity retention at 22 °C.

25 ENERGY STORAGE↗
DOE OSTI2023

Assessment of habitat‐specific competition for oral rabies vaccine baits between raccoons and opossums

Abstract Throughout the eastern United States, the National Rabies Management Program (NRMP) distributes oral rabies vaccine (ORV) baits to manage rabies virus circulation in raccoon ( Procyon lotor ) populations. The consumption of vaccine baits by non‐target species including Virginia opossums ( Didelphis virginiana ) may reduce the effectiveness of ORV programs, but competition for baits remains poorly quantified in many areas of the southeastern United States. We distributed placebo ORV baits injected with a biomarker across 4 land cover types (bottomland hardwood, upland pine, riparian, isolated wetland) on the Savannah River Site in South Carolina, USA, 2017–2019. We then trapped and collected whiskers from 247 raccoons and 78 opossums to assess biomarker presence using fluorescent microscopy. Our data revealed greater bait uptake probability by raccoons (estimated x̅ = 0.30, 95% CI = 0.19–0.44) compared to opossums (estimated x̅ = 0.11, 95% CI = 0.05–0.23) across all cover types surveyed. Probability of bait consumption was not affected by cover type or the abundance of raccoons or opossums. Among raccoons, males were more likely to consume baits than females (estimated x̅ = 0.28, 95% CI = 0.17–0.44 for males and 0.14, 95% CI = 0.05–0.31 for females) and probability of consumption increased by 0.08 with each additional day trapped during the 10‐day trapping session. Uptake rates for raccoons were relatively low compared to other studies and not influenced by competition with opossums. These low consumption rates indicate that additional research addressing the roles of baiting season, bait density, and resource selection will be important to maximize ORV bait uptake by target species in these southeastern landscapes.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Grafted nickel-promoter catalysts for dry reforming of methane identified through high-throughput experimentation

High-throughput synthesis of a series of monometallic and bimetallic catalysts (45 bimetallic and 50 monometallic samples) consisting of nickel and one of nine different metal promoters (B, Co, Cu, Fe, Mg, Mn, Sn, V and Zn) supported on one of six different metal oxides alumina, ceria, magnesia, silica and titania) is carried out via organometallic grafting using a robotic platform. The catalysts are evaluated for their activity and selectivity for the dry reforming of methane at a feed ratio of CH 4 :CO 2 of 1 at 650–800 °C in a parallel flow reactor system. The type of oxide support prevails over the type of additive for both catalyst activity and stability. On Al 2 O 3 and MgO, Fe was found to be the best promoter; on SiO 2 , Cu is the best promoter at 700 °C and higher, while on TiO 2 , Mn is found to enhance the conversion at 800 °C. On CeO 2 , all additives except Fe have beneficial effects. Twenty-five catalysts show > 90% methane conversion with ten catalysts showing > 95% conversion at 800 °C with the H 2 :CO ratios ranging from 0.8 to 1.2. Amongst the ten highest performers, NiFe/Al 2 O 3 and NiFe/MgO are more active than Ni/Al 2 O 3 and Ni/MgO, respectively and were stable over a period of 25 h at 800 °C. Characterization on the as-prepared samples reveals highly dispersed phase, while after reduction in H 2 , highly dispersed and reduced nickel particles up to 10 nm are formed. The particles do not increase in size under dry reforming reaction conditions at 800 °C. An increased hydrogen consumption observed during H 2 -TPR of the nickel particles is positively correlated with methane conversion for Al 2 O 3 -based catalysts. The resistance to deactivation by coking and variation in coke structure are investigated by spectroscopic and microscopic methods to identify the relationship between metal promoters, alloy formation, and type of surface carbon deposits. Carbon whiskers were observed on the ten selected spent samples and are preferentially deposited on Ni rather than on the promoters. Carbon nanotube formation and metal particle removal from support were not observed to cause deactivation while amorphous carbon formation was clearly linked to catalyst deactivation, as amorphous carbon could encapsulate nickel, either on the support or at the end of the carbon nanotube. Furthermore, the organometallic grafting technique is an efficient and suitable technique for synthesizing highly dispersed and homogeneous phases which lead to high conversion and high durability for dry reforming of methane.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Zeolites interactions with microwaves during methane non-oxidative coupling

Microwave-zeolite interactions during direct non-oxidative reactions of methane were studied using three H-ZSM-5 zeolites with different concentrations of Bronsted acid sites. The formation of C 2 and aromatic hydrocarbons increased with increasing surface acidity. When compared to conventional heating, the microwave reaction produced less carbon with higher thermal stability. The increase in diffraction shifts and the decrease in its surface area of microwave-reacted zeolite suggested that the carbon started depositing inside the micropores rather than on the external surfaces. Inhomogeneous carbon deposits with filamentous carbon whiskers were observed under microwave compared to homogeneous spherical carbon deposits on the conventionally reacted sample. The dielectric properties and Raman analysis suggested that the graphitic nature and the thermal stability of deposited carbon increased with zeolite surface acidity under microwave. We believe that this is a very important study for designing microwave active zeolite-based catalysts with a low affinity towards carbon formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Additive manufacturing of continuous carbon fiber-reinforced SiC ceramic composite with multiple fiber bundles by an extrusion-based technique

Due to the high cost, complex preparation process and difficulty in structural design, the traditional methods for carbon fiber-reinforced SiC ceramic composite preparation have great limitations. This paper presents a technique for the additive manufacturing multiple continuous carbon fiber bundle-reinforced SiC ceramic composite with core-shell structure using an extrusion-based technique. A conventional nozzle system was modified to print simultaneously a water-based SiC paste with continuous carbon fibers. Different levels of binder contents were investigated to optimize the stickiness, viscosity, thixotropy and viscoelasticity of the paste. After sintering, SiC whiskers were generated on the surface of fiber, which is conjectured to be due to the reaction between SiO and carbon fiber at high temperature. The continuous carbon fiber-reinforced SiC ceramic composite exhibited non-brittle fracture. In conclusion, the flexural strength of the additively manufactured Cf/SiC composites improved from 162 MPa with no fiber bundles to a maximum of 219 MPa with three fiber bundles.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Graphite crystals in catalytically-graphitized glass-like carbon

Catalytic graphitization of glass-like carbon leads to enhanced growth of micro-sized graphitic crystals with unusual shapes of wires, filaments, tubes, rods, whiskers, and spirals. Similar particles with axial symmetry are also found in pure glass-like carbon heat-treated at high temperatures. Nonetheless, the presence of a graphitization catalyst, Si in this case, in the heat-treatment process supports the transformation of porous, disordered carbon structure towards the graphitic atomic order and the formation of manifold peculiar polyhedral wires and particles of geometry distinct from the plate-like shape typical for conventional graphite. In contrast to conventional carbon nanotubes and fibers, the graphene layers are stacked perpendicular to the tube axis, while the size of the most common tube fibers can reach up to 10 μm in diameter and 100 μm in length. X-ray diffraction, Raman spectroscopy, scanning and transmission electron microscopy, small-angle X-ray scattering combined with complementary techniques have been used to characterize the structure of the glass-like carbon derived from furfuryl alcohol catalytically-graphitized using Si particles at 3000 °C. Finally, since control of graphite shape is vital to achieving the level of performance required in contemporary applications, the obtained results demonstrate that the catalytic graphitization method may be employed to produce filamentous graphite crystals.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Improved adhesion of polyurethane-based nanocomposite coatings to tin surface through silane coupling agents

Conformal coatings with higher adhesion strength is critical for mitigating the growth of whiskers from the pure tin (Sn) or Sn-rich surfaces of the Pb-free electronics. Silane coupling agents have the ability to form a durable bond between polymeric coatings and metallic materials. The main goal of this paper is to investigate the effect of silane agents on the adhesion behavior of polyurethane (PU), polyurethane acrylate (PUA) and both coatings filled with silicone rubber (SR) nanoparticles on the tin solder pads. It was found that an isocyanate-based silane provided excellent adhesion for PU and PU + SR coatings and an acrylic-based silane for PUA and PUA + SR coatings on the tin surface. This was due to the reaction bond formation between the silane coupling agent and the coating. Hence, the selection of silane coupling agents with the organofunctional group similar to the coating material is crucial to improve the adhesion properties of the coating.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Current Density Regulated Atomic to Nanoscale Process on Li Deposition and Solid Electrolyte Interphase Revealed by Cryogenic Transmission Electron Microscopy

Current density has been perceived to play a critical rule for controlling Li deposition morphology and solid electrolyte interphase (SEI). However, the atomic level mechanism of current density on Li deposition and the SEI remains unclear. In this work, based on cryogenic transmission electron microscopy imaging combined with energy dispersive X-ray spectroscopy and electron energy loss spectroscopy electronic structure analyses, we reveal the atomic level correlation of Li deposition morphology and SEI with current density. We discover that increasing current density leads to increased overpotential for Li nucleation and growth, leading to the transition from growth-limited to nucleation-limited mode for Li dendrite. Independence of current density, the electrochemically deposited Li metal (EDLi) exhibits crystalline whisker-like morphology. The SEI formed at low current density (0.1 mA cm -2 ) is monolithic amorphous; while, a current density of above 2 mA cm -2 leads to a mosaic structured SEI, featuring an amorphous matrix with Li 2 O and LiF dispersoids, and the thickness of the SEI increases with the increase of current density. Uniquely, the Li 2 O particles is spatially located at the top surface of the SEI, while LiF is spatially adjacent to the Li-SEI interface. These results highlight the possible tuning of crucial structural and chemical features of EDLi and SEI through altering deposit conditions and consequently direct correlation with electrochemical performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

ABSTRACT Zirconia‐toughened alumina (ZTA) ceramics with high mechanical properties were sintered by hot‐pressing method using SiC particles (SiCp) and SiC whiskers (SiCw) as the reinforcing agents simultaneously. The influences of sintering temperature, SiCp, and SiCw contents on the microstructure and mechanical properties of ZTA ceramics were investigated. It was found that both SiCp and SiCw could contribute to grain refinement significantly and promote the mechanical properties of the ceramics. However, the excess addition of SiCp or SiCw led to the formation of pores with large sizes and degraded the mechanical properties instead. When 13 wt% SiCp was introduced, the maximum flexural strength of 1180.0 MPa and fracture toughness of 15.9 MPa·m 1/2 were obtained, whereas the maximum flexural strength of 1314.0 MPa and fracture toughness of 14.7 MPa·m 1/2 were achieved at 20 wt% SiCw. Interestingly, the simultaneous addition of SiCp and SiCw could further improve the mechanical properties, and the highest flexural strength of 1334.0 MPa and fracture toughness of 16.0 MPa·m 1/2 were achieved at a SiCw/SiCp ratio of 16/4. The reinforcement mechanisms in the ceramics mainly included the phase transformation toughening of ZrO 2 , the crack deflection and bridging of SiCp and SiCw, and the pull‐out of SiCw.

Liu, Longyang↗
DOE OSTI2020

Final Technical Report for project entitled Highly Active, Durable, and Ultra-Low PGM NSTF Thin Film ORR Catalysts and Support

In this project, the objective was to develop new oxygen reduction reaction (ORR) electrocatalysts for proton exchange membrane fuel cells (PEMFCs) which could exceed all of the Department of Energy (DOE) 2020 targets listed in DE-FOA-0001224, Subtopic 1b, Table I. The expected outcome was development of one or more electrocatalysts which are substantially improved over the current state-of-the-art in terms of overall activity, durability, and cost, and are suitable for automotive traction and stationary fuel cell applications. This report summarizes this project’s progress towards meeting the stated objectives and includes a summary of key findings and conclusions. The development activities towards new highly active and durable thin film electrocatalysts has led to the discovery of several electrocatalysts which approached or exceeded several DOE 2020 targets for activity, durability, and performance in proton exchange membrane fuel cell (membrane electrode assemblies (MEAs). In this project, electrocatalyst development focused on systematic physical and electrochemical characterization of electrocatalyst activity, durability, and performance in MEAs as a function of electrocatalyst fabrication, compositional and structural variables. The project approach was to develop relationships between the catalyst functional responses (activity, durability and performance) with catalyst physical properties and catalyst fabrication methods. Additionally, the thin film catalysts were integrated onto the unique and durable 3M Nanostructured Thin Film (NSTF) support, consisting of arrays of self-assembled organic crystalline whiskers. The catalysts were evaluated against the project targets via extensive electrochemical characterization in MEA format at 3M, advanced structural and compositional microscopy at Oak Ridge National Laboratory (ORNL), and atomic structure analysis via XAFS at Argonne National Laboratory (ANL). The extensive electrochemical and physical characterization resulted in development of several trends which correlate the catalysts’ electrochemical properties to their physical properties, including composition, structure, and method of fabrication. The development was guided by density functional theory (DFT) modeling at Purdue University and kinetic Monte Carlo (kMC) modeling at Johns Hopkins University. The catalyst simulations provided key insights into the observed experimental activity and durability trends, and additionally were utilized to assess new electrocatalyst concepts prior to or coincident with physical catalyst development. This development has led to several electrocatalyst candidates with activity and durability which approach or exceed DOE targets. One class of catalysts, based on nm-scale thin layers of Pt on Ir, met or exceeded 6 of the 6 DOE targets the project addressed.

08 HYDROGEN↗
DOE OSTI2020

Novel Ionomers and electrode structures for improved PEMFC electrode performance at low PGM loadings (Final Report)

In this project, the objective is to develop new ORR electrocatalysts on optimized supports which can exceed all of the Department of Energy (DOE) 2020 targets listed in DE-FOA-0001412 directly relevant to the subtopic. This project’s approach is to develop novel, electrode-specific ionomers, and integrate them with state-of-the-art NSTF electrocatalyst powder to develop a cathode electrode achieving >= 044 A/mg PGM mass activity, <=30% mass activity loss during metal cycling, and <=0.125 g PGM /kW performance under DOE testing protocols. Ionomer O 2 permeability and proton conductivity will be increased by up to 1.5X over the baseline 3M800 perfluorosulfonate (PFSA) ionomer to enhance cathode electrode performance. Integration of cathode NSTF powder into an ionomer-containing electrode will increase the surface enhancement factor (SEF) to >=40 cm 2 PGM /cm 2 GEO allowing NSTF containing cathodes to exceed DOE MEA robustness targets. This report summarizes this project’s progress towards meeting the stated objectives and includes a summary of significant findings, conclusions, and developments over the entire project period from Oct. 1 st 2016 – Jan. 31 st 2020. This work has overcome key operation robustness issues with classic NSTF electrodes, identified pathways to improved dispersed and dispersed NSTF cathode performance, developed novel ionomers with high bulk conductivity and oxygen permeability, demonstrated exceptional support-independent electrode activity, and significantly increased metal and support stability through ionomer development. At this point, Tufts, MTU and all 5 FCPAD national labs have been involved, and contributed to, the improvements, learning and achievements of this work. Over the course of this project, more than 50 grams of dispersed NSTF powder in 15 different configurations have been generated, paving the way for scaleup within 3M. These whiskers have been processed in multiple ways, including acid leaching, powder-annealed, and sonicated by various means. For Task 2, 27 different types of ionomers were tested, 19 of which were made for the first time during the course of this project. 377 electrode inks with both NSTF and metal-on-carbon catalysts with I/C ratios from 0.2 to 1.2 were generated and mostly coated on a 3M pilot manufacturing line resulting in more than 700 different electrode types.

08 HYDROGEN↗
DOE OSTI2021

Development of Chromium and Sulfur Getter for Solid Oxide Fuel Cell (SOFC) System

Under the “real world” SOFC operating conditions, gaseous Cr and S species coexist in air stream. The combined Cr and S effect on the electrochemical poisoning of candidate LSM and LSCF electrodes has been investigated. Electrochemical and structural analysis revealed that the combined Cr and S interactions with the LSCF electrode remains significantly different from those of the individual Cr and S interactions. S reacts with the surface SrO accompanied by morphological changes whereas the hexavalent gaseous Cr species mainly deposit at the LSCF/GDC interface as is the case with Cr-only poisoning. For LSM electrode, the combined interactions of Cr and S remains similar to the sum of individual Cr and S effects as SO 2 reacts with Sr-rich regions of the bulk LSM, while Cr deposits at the electrochemically active sites. The use of getter, consisting of alkaline earth and transition metal oxides, has been proposed as a cost-effective approach to mitigate electrode poisoning. SrMnO 3 (SMO) is suggested as a robust getter material for the co-capture of airborne gaseous S and Cr species entering high-temperature electrochemical systems. The honeycomb getter forms, covered with SMO nanoparticles, were fabricated using dip coating. The SMO getter successfully maintained the electrochemical activity of LSM under the presence of gaseous Cr and S species, validating the efficacy of the getter. Post-test characterization revealed that the absorption of S and Cr contaminants led to the elongation of granular SMO particles, forming SrO nanorods and SrCrO 4 whiskers leaving Mn oxides underneath where inward-migrating Cr reside, indicating the high mutual affinity of Sr and Mn. The growth of reaction products during the long term exposure favors continued absorption of incoming S and Cr contaminants. The Mn 2 O 9 dimers, existing on the surface, are considered to help absorb S and Cr impurities, along with the Sr-terminated surface. The SMO getter also displays robust stability in humid environments at high temperatures without phase transformation or hydrolysis, fulfilling the requirement for operation in high-temperature electrochemical systems.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Rapid Predictions of Part Lifetimes in Corrosive Environments, Corrosion

Corrosion challenges persist throughout SNL’s mission areas. The primary difficulty lies in the fact that corrosion typically manifests as isolated, rare events, making preemptive identification exceedingly difficult. Our current strategy for addressing corrosion issues, such as anomalies and SFIs, is similarly isolated and reactive. This method is costly, time-consuming, heavily dependent on a limited number of experts, and offers minimal understanding of the overall damage distribution within the stockpile. This technical challenge is not unique to corrosion but is also prevalent in other material aging phenomena, such as tin-whisker growth in lead-free solder and fatigue failure of springs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Methods for producing metal carbide materials

Methods of producing silicon carbide, and other metal carbide materials. The method comprises reacting a carbon material (e.g., fibers, or nanoparticles, such as powder, platelet, foam, nanofiber, nanorod, nanotube, whisker, graphene (e.g., graphite), fullerene, or hydrocarbon) and a metal or metal oxide source material (e.g., in gaseous form) in a reaction chamber at an elevated temperature ranging up to approximately 2400° C. or more, depending on the particular metal or metal oxide, and the desired metal carbide being produced. A partial pressure of oxygen in the reaction chamber is maintained at less than approximately 1.01×102 Pascal, and overall pressure is maintained at approximately 1 atm.

Garnier, John E.↗
DOE OSTI2022

Catalyst comprising Pt, Ni, and Cr

Catalysts comprising nanostructured elements comprising microstructured whiskers having an outer surface at least partially covered by a catalyst material comprising at least 90 atomic percent collectively Pt, Ni, and Cr, wherein the Pt is present in a range from 32.4 to 35.8 atomic percent, the Ni is present in a range from 57.7 to 63.7 atomic percent, and the Cr is present in a range from 0.5 to 10.0 atomic percent, and wherein the total atomic percent of Pt, Ni, and Cr equals 100. Catalyst described herein are useful, for example, in fuel cell membrane electrode assemblies.

Steinbach, Andrew J. L.↗
DOE OSTI2023

Multi-layered diamond-like carbon coating for electronic components

A multi-layer coating on an outer surface of a substrate includes a first layer applied directly to the outer surface of the substrate. The first layer includes diamond-like carbon (DLC) configured to mitigate metal whisker formation. A second layer is applied on a top surface of the first layer. The second layer is a conformal coating that includes a second material configured to bind to the top surface of the first layer and fill any microfractures that may form in the first layer. Optionally, a third layer is applied on a top surface of the second layer and includes DLC configured to protect the second layer from oxidation and degradation.

Selter, Thomas Matthew↗
DOE OSTI2025

Cutoff and Emergence of Dart Leaders in an Unbranched Positive Leader Simulation

Channel cutoff is the process by which an active lightning channel cools down, goes dark, and loses its ability to effectively conduct electricity. Current cutoff precedes several lightning phenomena, notably dart leaders and return strokes, but the process by which a hot, highly‐conducting leader channel can undergo current cutoff is poorly understood. In this work, we present self‐consistent simulations of positive leader propagation, which include coupled treatment of electrodynamics and plasma physics. The unstable positive leader spontaneously undergoes channel cutoff and creates the conditions for the emission of dart leaders, that is, it accumulates a packet of negative charge at the intersection between cutoff and conducting channel segments. A residual conductivity in the cutoff section facilitates the conversion of the electric field enhancement into a traveling wave, which retraces and reionizes the channel. This is critical for allowing the frail positive leader to keep propagating.

58 GEOSCIENCES↗